Hitachi 42PD6700U Instructions For Use Manual

42PD6700U

GB

Instructions for use

- 1 -

Contents

Remote Control Buttons ......................... 2

PLASMA TV ............................................. 4

Preparation ............................................. 6

Features ............................................... 6

Panel Features .................................... 6

Safety Precautions ................................. 6

Before Switching On Your TV ................ 9

Power Connection ............................... 9

Connections To The Aerial Input Socket ... 9

How To Connect Other Devices ........... 9

Inserting Batteries In The Remote

Control Handset ................................... 9

Switching The TV ON/OFF ...................... 9

To switch the TV on: ............................. 9

To switch the TV off: .............................. 9

Initial Settings ....................................... 10

Operating The TV .................................. 11

Operating with the buttons on the TV set . 11

Operating With Remote Control ........ 11

IDTV Menu System ............................... 11

Channel List ....................................... 11

Installation .......................................... 13

Configuration ..................................... 14

Timers ................................................ 16

Language ........................................... 17

TV Setup ............................................. 17

Common Interface ............................. 18

Analogue TV Menu System .................. 18

Picture menu ...................................... 18

Sound menu ...................................... 19

Feature menu ..................................... 21

Install menu ....................................... 22

Program menu ................................... 23

Source menu ..................................... 24

PC Mode ................................................ 24

Installation .......................................... 24

Menu System in PC mode ................. 25

PC Picture Position Menu .................. 25

PC Picture Menu ................................ 25

Sound Menu ....................................... 26

Feature Menu ..................................... 26

Source Menu ...................................... 26

Sound in PC mode ............................ 26

Other Features ...................................... 26

TV Status ............................................ 26

Mute Indicator ..................................... 26

PIP and PAP modes ........................... 26

Freeze Picture .................................... 26

Zoom Modes ...................................... 26

Teletext .................................................. 27

To Operate Teletext ............................ 27

To Select A Page Of Teletext ............... 27

To Select Index Page ......................... 28

To Select Teletext With A TV Programme 28

To Reveal Concealed Information ... 28

To Select A Subcode Page ................. 28

To Exit Teletext .................................... 28

To Display The Time .......................... 28

Fastext ................................................ 28

Connect Peripheral Equipment ........... 29

High Definition ................................... 29

Via The Scart ...................................... 29

Via Aerial Input .................................... 29

Decoder.............................................. 29

TV And Video Recorder ...................... 29

Playback NTSC .................................. 29

Copy Facility ....................................... 29

Search For And Store The Test Signal

Of The Video Recorder ...................... 29

Camera And Camcorder .................... 30

Connect The Decoder To The Video

Recorder ............................................ 30

Connecting Headphones .................. 30

Connecting Subwoofer ...................... 30

Aerial Connection ................................. 31

Tips ........................................................ 32

Specifications ....................................... 33

Appendix A: PC Input Typical Display

Modes .................................................... 34

Appendix B: DVD Player Selection ...... 35

Appendix C: Main and PIP-PAP Picture

Combinations ........................................ 36

UK Guarantee ........................................ 37

- 2 -

Remote Control Buttons













- 3 -

= Stand by On/Off

= Program Information

SEL= Select TV/ DVD /SAT

AV3 = AV3 mode

AV2 = AV2 mode

RGB2 = No Function

RGB1= PC mode

= Go back to previous menu

`

= Cursor Right

OK = Enter

b

=Cursor Down

= Picture Mode

P+/ - = Programme Up/ Down

= Mute On/Off

0 - 9 = Digit buttons

= PIP / PAP / TV

BLUE = Only used in Teletext mode

YELLOW = Only used in Teletext mode

= Reveal P- = Programme Down /

SLIDE SHOW/ = No function/ Subtitle

PHOTO= No Function

SWIVEL= No Function

= Aspect ratio

= Teletext On/Off

= Time

= Guide for DTT/ Index Pagefor TV

GREEN = Only used in Teletext mode

RED = PAT (Picture and Text)

= Freeze On/Off

/ = Volume Up/ Down



= Mono/Stereo - Dual A-B



= Equalizer Sound Mode



_

= Cursor Left

a

= Cursor Up

= Menu On/Off

AV5 =AV5 mode

AV4 = AV4 mode

AV1 = AV1 mode

DTT/TV = Selector button for Digital/Ana-

logue mode

- 4 -

PLASMA TV

FRONT VIEW

REAR VIEW

- 5 -

On/Off switch

Volume Up, Volume Down buttons

Prog. Up, Prog. Down buttons

MENU button

TV/AV button

Power cord input

S-VHS Input

Video Input

Audio Inputs

Headphone

Audio Line Outs

Subwoofer Out

PC Audio Input

Aerial

Scart 2 (AV-2)

Scart 1 (AV-1)

HDMI Input (AV-5)

Component Audio Inputs

Component Video (YPbPr) Inputs

VGA Input

CI Slot

AV-4

AV-3

- 6 -

Preparation

For ventilation, leave a space of at least 10

cm free all around the set. To prevent any

fault and unsafe situations, please do not

place any objects on top of the set.

Use this apparatus in tropical and/or moder-

ate climates.

Features

 Remote controlled colour television.

 Fully integrated Digital TV (DVB-T)

 100 programmes from VHF, UHF bands or

cable channels can be preset.

 It can tune cable channels.

 Controlling the TV is very easy by its menu

driven system.

 It has 2 Scart sockets for external devices

(such as video, video games, audio set,

etc.)

 3DS Virtual Surround Sound

 Stereo sound system (German+Nicam).

 Full function Teletext .

Fastext (1000 Pages), TOP text.

 Headphone connection.

 Direct channel access.

 A.P.S. (Automatic Programming System).

 All programmes can be named.

 Forward or backward automatic tuning.

 Sleep timer.

 Child Lock.

 Automatic sound mute when no transmis-

sion.

 NTSC Playback.

 AV in and S-VHS in are available.

 It has VGA connector for external devices

such as computer.

 It has an HDMI connector for Digital Video

and Audio. This connection is also de-

signed to accept High Definition signals.

 It has PIP / PAP / PAT functions.

 AVL (Automatic Volume Limiting)

 TV Picture in PC

 When no valid signal is detected, after 5

minutes the TV switches itself automatically

to stand-by mode.

 PLL (Channel Search)

 PC Input (Support up to SXGA 1280 x 1024)

 Stereo PC Audio Input

 Plug&Play for Windows 9X, ME, 2000, XP

 3D Comb Filter

 Audio Line Out

Panel Features

 42-inch PLASMA display.

 High resolution (1024x1024)

 Contrast ratio (3000:1 typical)

 Brightness (typical) 1400 cd/m

2.

 Display colour 16.7 Million.

Safety Precautions

IMPORTANT SAFETY

INFORMATION ON OPERATING

YOUR TV

Dos and Donts

DOs

This Television has been designed and manu-

factured to meet international safety standards,

but like any electrical equipment, care must be

taken if you are to obtain the best results and

safety is to be assured.

DO read the operating instructions before you

attempt to use the equipment.

DO consult your dealer if you are in any doubt

about installation, operation or safety of your

equipment.

DO be careful with glass panels or doors on

equipment.

This TV is supplied with a fitted mains plug.

This plug must not be cut off as it may contain

a special radio interference filter, the removal

of which could lead to impaired performance.

If you wish to extend the lead, obtain an appro-

priate safety approved extension lead or con-

sult your dealer.

- 7 -

Observe the manufacturers instructions when

connecting extension leads to the TV. Check

the fuse rating on the new plug, this should be

fitted with a 5 Amp fuse which conforms to ei-

ther ASTA or BSI (BS1 362) approvals, these

are easily identifiable by either the

or

symbols. If you are in any doubt about the in-

stallation of an extension lead, please consult

a competent electrician.

DONTs

DONT continue to operate the equipment if

you are in any doubt about it working normally,

or if it is damaged in any way switch off, with-

draw the mains plug and consult your dealer.

DONT place water filled vessels on top of T.V.

cabinets.

DONT remove any fixed cover as this may ex-

pose dangerous voltages.

DONT leave equipment switched on when it is

unattended unless it is specifically stated that

it is designed for unattended operation or has

a stand-by mode. Switch off using the switch

on the equipment and make sure your family

know how to do this. Special arrangements

may need to be made for infirm or handi-

capped people.

DONT use equipment such as personal ste-

reos or radios so that you are distracted from

the requirements of traffic safety. It is illegal to

watch television whilst driving.

DONT obstruct the ventilation of the equipment,

for example with curtains or soft furnishings.

Overheating will cause damage and shorten

the life of the equipment.

DONT use makeshift stands and NEVER fix

legs or stands to the TV with any screws other

than those provided - to ensure complete safety

always use the manufacturers approved stand

with the fixings provided.

DONT allow electrical equipment to be ex-

posed to rain or moisture.

ABOVE ALL

 NEVER let anyone, especially children

push anything into holes, slots or any

other opening in the case - this could re-

sult in a fatal electric shock.

 NEVER guess or take chances with elec-

trical equipment of any kind - it is better to

be safe than sorry!

1. Power Source

The receiver should be operated only from a

220-240V AC, 50 Hz. outlet. Ensure you se-

lect the correct voltage setting for your conve-

nience.

2. Power Cord

The power supply cord should be placed so

that it is not likely to be walked on or pinched

by items placed upon them or against it. Pay

particular attention to cord where it enters

the plug, power outlet, and the point where it

exits from the receiver.

3. Moisture and Water

Do not use this equipment in a humid and

damp place (avoid the bathroom, the sink in

the kitchen, and near the washing machine).

Do not expose this equipment to rain or wa-

ter, as this may be dangerous and do not

place objects filled with liquids on top. Avoid

from dripping or splashing.

4. Cleaning

Before cleaning, unplug the receiver from

the main supply, outlet. Do not use liquid or

aerosol cleaners. Use soft and dry cloth.

5. Ventilation

The slots and openings on the receiver are

intended for ventilation and to ensure reli-

able operation. To prevent overheating,

these openings must not be blocked or cov-

ered in anyway.

6. Lightning

In case of storm and lightning or when go-

ing on holiday, disconnect the power cord

from the wall outlet.

7. Replacement Part

When replacement parts are required, be sure

the service technician has used replacement

parts which are specified by the manufacturer

or have the same specifications as the origi-

- 8 -

The Plasma TV is a very high techology

product giving you fine picture details. Occa-

sionally, a few non-active pixels may remain

still on the screen. Long-time unmoving still

pictures may cause permanent shade effect

on the screen and even the picture has been

changed, its influence lasts as ghost pic-

ture. This ghost effect may disturb the user

even though it will diminish in the course of

time. To prevent this, don't leave still pictures

for example teletext pages or frozen pictures

on the screen for a long time. Please note

that this does not affect the performance of

your product.

DO NOT LEAVE YOUR TV AT STAND-BY

OR OPERATING WHEN YOU LEAVE YOUR

HOUSE

nal one. Unauthorised substitutions may re-

sult in fire, electrical shock, or other hazards.

8. Servicing

Please refer all servicing to qualified per-

sonnel. Do not remove cover as this may re-

sult in electric shock.

9. Naked Flame Sources

Do not place naked flame sources on the

apparatus.

WARNING: When the device is not in use

for a long time, disconnect from power.

Instructions for waste disposal:

 Packaging and packaging aids are recy-

clable and should principally be recycled.

Packaging materials, such as foil bag, must

be kept away from children.

 Battery, including those which is heavy

metal-free, should not be disposed of with

household waste. Please dispose of used

battery in an environmentally sound man-

ner. Find out about the legal regulations

which apply in your area.

- 9 -

Before Switching On Your TV

Power Connection

IMPORTANT: The TV set is designed to op-

erate on 220-240V AC, 50 Hz.

 After unpacking, allow the TV set to reach the

ambient room temperature before you con-

nect the set to the mains.

Connections To The Aerial Input

Socket

 Connect the aerial or cable TV plug to the

Aerial input socket located at the rear of the

TV and connect the cable plug coming out

from the TV out socket located on the de-

vices (VCR, DVB etc.) to this socket as well.

How To Connect Other Devices

IMPORTANT: Switch off the TV before con-

necting any external device.

Sockets for external connections are at the

rear side of the TV. For connection of other

devices via Scart refer to the manuals of the

related devices.

Inserting Batteries In The Remote

Control Handset

 Remove the battery cover located on the

back of the handset by gently pulling down-

wards from the indicated part.

 Insert two AA/R6 or equivalent type batteries

inside. Place the batteries in the right direc-

tions.

 Replace the battery cover.

NOTE: Remove the batteries from remote

control handset when it is not to be used for

a long period.Otherwise it can be damaged

due to any leakage of batteries.

Switching The TV ON/OFF

To switch the TV on:

Your TV will switch on in two steps:

1- Connect the power supply cord to the sys-

tem. Press On/Off switch 

 on the TV.

Then the TV switches itself to stand-by mode

and the led on the front of the TV becomes

Red.

2- To switch on the TV from stand-by mode

either:

Press a digit button on the remote control so

that a programme number is selected,

or,

Press the "

" or " " button on the TV or

press the P- or P+ button on the remote

control, so that last mode switched off is se-

lected.

By either method the TV will switch on and

the led becomes green.

To switch the TV off:

 Press the  (stand-by) button on the re-

mote control, so the TV will switch to stand-

by mode and the GREEN LED will become

RED.

To power down the TV completely, press

On/Off switch 

,

or,

Unplug the power cord from the mains

socket.

- 10 -

Initial Settings

When the TV is turned on for the first time, it

is in the digital mode.

Because this is the first time the TV is used,

there are no channels stored in the memory

and the following message appears on the

screen.

 To start installation process, select Yes,

to cancel select No.

 To select an option Yes or No, highlight

the item by using

or buttons and press

the OK button.

The IDTV will automatically tune to the UHF

transmission channels 21 to 68 looking for

digital terrestrial TV broadcasts and display-

ing the names of channels found. This pro-

cess will take about five minutes. To cancel

searching, you can press the 

 button at

any time during the process.

After Automatic Search process is com-

pleted, the following message asking for

analogue channel search appears on the

screen. TV switches to the analogue TV

mode.

To seach for analogue channels, select

Yes.

Press the BLUE button to cancel APS if you

do not want to delete your existing

programme list.

To continue APS, first select the country by

pressing

_

/

`

button and then press the

RED or OK button.

After APS is finalized, the programme table

will appear on the screen. In the programme

list you will see the programme numbers

and names assigned to the programmes.

If you do not accept the locations and / or the

programme names of programmes, you

can change them in Program menu. For de-

tails see Program menu on page 23.

To display channel list in IDTV, switch to the

IDTV via pressing the DTT/TV button. Then

press the   button to enter main menu,

Channel List will be highlighted. Press the

OK button to enter the menu.

- 11 -

Operating The TV

You can operate your TV using both the re-

mote control handset and the buttons on the

set.

Operating with the buttons on the

TV set

Volume setting and programme selection

can be made by using the buttons on the

control panel at the bottom of the TV.

Volume Setting

Press the -

 button to decrease volume

or the  + button to increase volume, so

a volume level scale (slider) will be dis-

played at the bottom of the screen.

Programme Selecting

Press the 

 button to select the next

programme or the 

 button to select the

previous programme.

Entering The Menu

Press the MENU button on the control

panel at the bottom of the TV to enter the

menu.



/  and  + / -  buttons on the TV

are used as navigation buttons in menu.

AV Mode

Press the AV button on the control panel

at the bottom of the TV to switch your TV to

AV modes.

Operating With Remote Control

The remote control handset of your TV is de-

signed to control all the functions of your TV.

The functions will be described in accor-

dance with the menu system of your TV.

Functions of the menu system are de-

scribed in Menu System section.

Volume Setting

Press the button to increase volume.

Press the button to decrease volume. A

volume level scale (slider) will be displayed

at the bottom of the screen.

Programme Selecting

(Previous or next programme)

 Press the P- button to select the previous

programme.

 Press the P+ button to select the next

programme.

Programme Selecting (direct access):

Press digit buttons on the remote control

handset to select programmes between 0

and 9. The TV will switch to the selected

programme after a short delay.

 For a two digit programme number enter the

second digit after pressing the first digit

within 2 seconds.

IDTV Menu System

The IDTV menu can only be shown when

watching Digital terrestrial broadcasting.

Press the DTT/TV button to turn IDTV on

while TV is in analogue mode.

Press the   button. The menu below

appears on the screen:

Channel List

Using the or button on the remote con-

trol in Main menu, make sure that the first

item, Channel List, is highlighted and press

the OK button to display the Channel List.

The following operations can be performed

in this menu:

1. Navigating the whole list of channels

2. Deleting channels

3. Renaming channels

4. Adding locks to channels

5. Setting favourites

Channel List is the place where the chan-

nels are managed.

- 12 -

Navigating the whole channel list

Press

or button for selecting the previ-

ous or next channel.

To watch a specific channel, highlight the

Select item in the channel list using the

or button. Then using the or button

select the desired channel and press the

OK button.

The selected channel has the name dis-

played to the top-right and the channel num-

ber to the top left of the channel preview

pane, as shown in the above diagram.

Deleting the channels in the channel list

Press or button to select the channel

that will be deleted.

Press

or button to select the Delete

item on Channel List menu. As seen on

Channel List menu, Select is written next to

Delete item at the bottom of the screen to in-

dicate that press the OK button to delete

the highlighted channel in the channel list.

Press the OK button to delete the high-

lighted channel in the channel list. Then the

following message appears on the screen.

Press or button to highlight the desired

option. If OK button is pressed while Yes

is highlighted, the highlighted channel is de-

leted. Selecting No cancels the delete op-

eration.

Renaming channels

To rename a specific channel, the channel

must be highlighted via pressing

or

button and then highlight the Edit Name item

by pressing

or button. Press OK to ac-

tivate rename feature.

Now pressing or button moves to the

previous/next character. Pressing

or

button toggles the current character, i.e., b

character becomes a by

and c by .

Pressing the numeric buttons 0...9 re-

places the highlighted character with the

characters printed above the button one by

one as the button is pressed.

Press the   button to cancel the editing

or OK button to save the new name.

Adding locks to channels

Channel Locking provides a password-pro-

tected access to channels selected by par-

ents. In order to lock a channel you should

know the Parental Lock password (default

value is set to 0000 in the factory and can

only be changed from the Configuration

Menu).

- 13 -

Select the channel to be locked by highlight-

ing it and select the Lock option by press-

ing

or button. When the OK button is

pressed, a password box is displayed.

Enter the password using the digit buttons

on the remote control. The Lock icon

will

now be displayed next to the selected chan-

nel. Repeat the same operation to cancel

the Lock.

Setting Favourites

You can set various channels as favourites

so that only the favourite channels are navi-

gated when you press the P +/- keys on the

remote control. To set a favourite you should

highlight the Favourites item at bottom of

the Channel List menu.

Use the

or button to highlight the

Favourites item at the base of the screen

and then, in turn, highlight each channel you

want to add to the favourites list, using the

and buttons and press the OK button.

A channel selected as a favourite appears

in the main channel list with a favourites

icon (

) against the channel name.

You must then set the Favourite mode to

ON in the Configuration menu (see page 15

for further details).

On Screen Help Pressing INFO Button

For all menus press the 

 button to dis-

play the help information about the menu

functions. For Channel List menu the follow-

ing message is displayed on the screen.

Installation

The Installation menu mainly intends to help

you for building a Channel Table in the most

efficient way.

This menu includes the following items:

1. Add New Channels

2. First Time Installation.

ADD NEW CHANNELS:

This tuning menu consists of two parts:

·Automatic Search

·Manual Search

Automatic Search:

Automatic search is started by pressing the

OK button in the auto-search pop up

- 14 -

menu. All the services are searched and a

channel table is created automatically.

All channels found are stored in a sorted

form with respect to their channel numbers.

Some services may not appear with the cor-

rect channel number. At the time of printing,

not all broadcasters are sending their chan-

nel number information.

Manual Search:

In manual search, the number of the multi-

plex is entered manually and only that multi-

plex is searched for the channels. For every

valid channel number, signal level, signal

quality and network name are shown at the

bottom of the screen.

In both manual and auto search any existing

channel in the database is not re-stored to

avoid redundant duplicates of that channel.

FIRST TIME INSTALLATION

The user can use this item to load default

settings, which had been loaded to the re-

ceiver at the factory.

To install factory settings, highlight First

Time Installation menu and press the OK

button, then you will be asked to confirm for

deleting all channels and settings.

By selecting YES and pressing the OK but-

ton, the existing channel table will be de-

leted.

After factory settings is loaded, First Time

Installation menu will be displayed.

Press the OK button to start installation. Af-

ter search is completed for digital channels,

a message asking search for analogue

channels appears on the screen.

Press the OK button to search for ana-

logue channels.The following menu ap-

pears on the screen for analogue channel

search.

First of all choose Language and Country by

using

/ and / buttons. This will af-

fect the sort process in APS. To start APS,

press the RED or OK button.

After APS is finalized, the programme table

will appear on the screen. In the programme

table you will see the programme numbers

and names assigned to the programmes.

If you do not accept the locations and / or the

programme names, you can change them

in the Program menu. (See page 23 for Pro-

gram table explanation.)

Configuration

Press the MENU button to display the Main

Menu and the button twice to highlight

Configuration, then press the OK button to

display the Configuration menu. Press the

MENU button to leave the menu.

- 15 -

The various configuration functions are dis-

played in a list, along with a quarter-screen

image of the currently selected channel. You

can select a function by highlighting the cor-

responding menu line using the

or but-

ton.

Audio Language

Digital terrestrial television channels can

broadcast simultaneous soundtracks in

more than one language. This function se-

lects which language soundtrack you will

hear when switching to a channel broad-

casting with the multiple soundtracks.

Highlight the Audio Language line in the

Configuration menu and use the

or

button to cycle through the language op-

tions.

Subtitle

Digital terrestrial television channels can

broadcast subtitles displayed on-screen for

the hard-of-hearing. This function selects

the desired subtitle language and enables

the automatic display of subtitles whenever

subtitle information is broadcast.

Highlight the Subtitle line in the Configura-

tion menu and use the

or button to

cycle through Off and language options.

Favourite Mode

This function enables or disables the

favourite channel list mode. See Channel

List menu Favourites on page 13.

Use

or button to turn on/off favourite

mode. If the Favourite Mode is on, in nor-

mal operating mode pressing P+ and P-

buttons will only navigate through the chan-

nels that were previously defined as

favourites in Channel List.

EPG Preference

Digital terrestrial television channels can

broadcast simultaneous Next&Now and 7-

Day electronic programme.

Highlight the EPG Preference line in the

Configuration menu and use the

or

button to select Next&Now or 7-Day.

Receiver Upgrade

The IDTV can be upgraded via the configura-

tion menu, entered from the main menu.

In the Configuration menu, highlight the

Receiver Upgrade item by pressing

or

button and press the OK button to start

upgrade process.

There are two possibilities for Receiver soft-

ware to be upgraded: automatic and

manual.

Automatic Download (Automatic upgrade)

Automatic Download can be enabled or

disabled by pressing

or button. If it is

enabled, then there are two ways for auto-

matic upgrade. The first one is checking the

existence of a new software every time the

IDTV goes to standby. The second one is

waking up at 03:00 a.m. every night, pro-

vided that the IDTV is left in standby mode.

- 16 -

Both automatic upgrade methods result in

standby mode either upgraded or not.

If the automatic upgrade is set to Disabled

then this function will not work.

Search For New Version (Manual upgrade)

Manual upgrade starts if the Search for

New Version item is highlighted by using

or button and activated via pressing

the OK button.

After Search for New Version is acti-

vated, the IDTV tunes to each frequency that

have been stored in its database and looks

for the new software.

Parental Settings

Some channels broadcast material which

you do not want younger members of the

family to watch. Any channel can be locked

so that it cannot be selected for viewing with-

out first a four-digit PIN code being entered.

In this way any channel not suitable for

younger viewers can be protected.

This function enables or disables the menu

protection system and allows the PIN code

to be changed.

Use

or button to go to Parental Set-

tings option. Press the OK button to enter

Parental Settings Menu. A box asking for the

lock key is displayed.

There is only one key which is set to 0000

initially. Enter lock key. If wrong Lock key is

entered, the following message is displayed

on the screen and it is returned back.

If it is correct, the Parental Settings Menu in-

cluding following items is displayed:

There you can set/reset locking for the Main

Menu, or the Installation Menu to restrict ac-

cess. If the menu lock is disabled, there will

be free access to the menu system. Also in

this menu you can change the lock key and

set/change parental lock mode.

Disabled: All menus are unlocked.

Main Menu: Main menu is accessible only

with the correct lock key. So the user cannot

add, delete, rename, move channels, cannot

set timers.

Installation: Installation menu is locked, so

the user cannot add channels.

Changes will be updated after exiting Con-

figuration Menu.

Timers

Display the Main Menu by pressing the

MENU button. Highlight the Timers line by

pressing

or button and press the OK

button to display the Timer menu.

Up to five separate timer events can be set

and each is displayed in the Timer screen,

showing the event number, the channel to

be selected, the start time, end time, date

and the mode - whether that event is active

(and will be acted on) or not.

- 17 -

 To set an event, highlight its mode button

using the

or button and press the OK

button to display the timer entry window.

 Here the five settings of channel name,

start time, end time, date and frequency

mode can be set. You can move freely be-

tween each setting using the

or but-

tons.

 The channel name is set using the

or

button to display the channel which broad-

casts the programme.

 The start time, end time and date are each

set with the digit buttons on the remote con-

trol in 24-hour format.

 The frequency mode determines how of-

ten the receiver operates this event and is

set with the

or button to be either Once,

Daily, or Weekly.

If an invalid number for the start or end times

or the date is entered, Entered time is not

valid message appears on the menu.

RECORDING FROM IDTV

Connect your VCR to AV2 via a scart lead.

Set the AV2-OUT in the feature menu to DDT,

as illustrated on page 21 and described on

page 22.

Set the time as described above.

Set your TV to standby using the remote

control.

Set your VCR to correspond with the time set

on your TV and select external input (refer to

your VCR instruction book).

NB. If you switch on your TV whilst the timer

recording is active and then switch back to

standby, the timer recording will be cancelled;

the timer setting will be deleted and the desi-

red programme will not be recorded.

Language

Some programmes are broadcast in two or

more languages simultaneously. The lan-

guage heard can be selected from the Lan-

guage Menu.

 Press the   button to display the Main

Menu and use

or button to highlight the

Language line and press the OK button.

 Use the or button to highlight the

soundtrack language required and press

the OK button. Normal viewing, with the re-

quired language soundtrack, can be re-

sumed by pressing the 

 button.

 If the programme has no alternative lan-

guage soundtrack broadcast, the Language

Menu will not be available, but a message,

No Multi Language Available is displayed

briefly.

TV Setup

To be able to go through TV functions, you

can use this item.

The digital TV Setup menu screen is ac-

cessed from the main menu. Press the

  button to display the main menu and

use

or button to highlight TV Setup,

- 18 -

press the OK button to display TV Setup

menu screen.

Detailed information about Sound, Picture

and Feature menus are in AnalogueTV

Menu System section on page 18.

Common Interface

 Press the   button to display the Main

Menu and use the or button to highlight

the Common Interface line and press the

OK button.

It is required to subscribe to a pay channel

company to view the pay channels of the

Digital Terrestrial broadcasting.

Obtain the Conditional Access Module

(CAM) and the Viewing card by subscribing

to a pay channel company, then insert those

to the Television using the following proce-

dure.

1. Switch off the TV and unplug from the

mains.

2. Insert the CAM, then Viewing Card to the

slot that is located in the terminal cover at

the left-hand side of the TV (from front

view).

 The CAM should be correctly inserted, it is

impossible to insert fully if reversed. The

CAM or the TV terminal may be damaged if

the CAM is forcefully inserted.

3. Connect the TV to the mains supply,

switch on and then wait for few moments

until the card is activated.

 Some CAMs may require the following set

up. Please set the CAM by entering the IDTV

menu, Common Interface then pressing the

SELECT button. (CAM set up menu is not

displayed when it is not required.)

 To see the viewing contract information:

Enter IDTV; press the 

 button, then high-

light Common Interface and press the OK

button.

 When no module is inserted, No Common

Interface module detected message ap-

pears on the screen.

 Refer to the module instruction manual for

details of the settings.

Analogue TV Menu System

Your TV has been designed with a menu

system to provide easy manipulation of a

multifunction system.

Press the

button to enter the menu.

Press

_

/

`

button to select a menu title and

then

a

/

b

button to select a menu item and

_

/

`

or OK button to enter the menu item.

 Press the

button to exit the menu.

 Press the button to return to the previous

menu.

- 19 -

Picture menu

By pressing

_

/

`

button, select the first icon.

Picture menu appears on the screen.

Mode

By pressing

a

/

b

button, select Mode.

Press

_

/

`

button to choose one of these

options: Natural, Dynamic and Cinema.

Picture mode can be changed directly by

pressing the button.

Contrast

By pressing

a

/

b

button, select Contrast.

Press

`

button to increase contrast. Press

_

button to decrease contrast. Contrast level

can be adjusted between 0 and 63.

Brightness

By pressing

a

/

b

button, select Bright-

ness. Press

`

button to increase brightness.

Press

_

button to decrease brightness.

Brightness level can be adjusted between 0

and 63.

Sharpness

By pressing

a

/

b

button, select Sharp-

ness. Press

`

button to increase sharpness.

Press

_

button to decrease sharpness.

Sharpness level can be adjusted between 0

and 31.

Colour

By pressing

a

/

b

button, select Colour.

Press

`

button to increase colour. Press

_

button to decrease colour. Colour level can

be adjusted between 0 and 99.

Hue

This item is displayed in picture menu when

the TV receives an NTSC signal. By press-

ing

a

/

b

button, select hue. Press

`

button

to increase hue. Press

_

button to decrease

hue. Hue level can be adjusted between -31

and 31.

Colour Temp

By pressing

a

/

b

button, select Colour

Temp. Press

_

/

`

button to choose one of

these options: Cool, Normal and Warm.

Noise Reduction

This item is used to reduce the image noise

and improve the picture quality at weak sig-

nals.

By pressing

a

/

b

button, select Noise Re-

duction. Press

_

/

`

button to set Noise re-

duction level to Off, Low, Medium or High.

Film Mode

Films are recorded at a different number of

frames per second to normal television

programmes.

By pressing

a

/

b

button, select Film Mode.

Press

_

/

`

button to set this feature On or

Off. Turn this feature on when you are watch-

ing films to see the fast motion scenes

clearly.

3D Comb

3D Comb is used to improve colour transi-

tions and colour quality of pictures.

By pressing

a

/

b

button, select 3D Comb.

Press

_

/

`

button to set this feature On or

Off.

Page is loading ...

Hitachi 42PD6700U Instructions For Use Manual

Hitachi 42PD6700U Instructions For Use Manual

Related papers

Other documents