Sherwood 50-1445 Installation guide
- Category
- Cookers
- Type
- Installation guide
This manual is also suitable for
Sonnet Fuel Conversion
Kit - 50-1445 & 50-1446
Please read and understand these instructions before installing. Failure to follow these
instructions carefully could cause property damage or personal injury.
Warning: This conversion kit shall be installed by a qualied service agency in accordance with
the manufacturer’s instructions and all applicable codes and requirements of the authority
having jurisdiction. If the information in these instructions is not followed exactly, a re,
explosion or production of carbon monoxide may result causing property damage, personal
injury or loss of life. The qualied service agency is responsible for the proper installation of
this kit. The installation is not proper or complete until the operation of the converted appliance
is checked as specied in the manufacturer’s instructions supplied with the kit.
Kit Parts List:
1 - Orice (Natural Gas #42 DMS or Propane #54 DMS)
1 - Conversion label 1 - Installation instruction sheet
Carefully inspect the orice supplied with this conversion kit. If it has been damaged or is missing, contact
your dealer, distributor or courier company to have them replaced before starting this installation. It is highly
recommended that you have your Sonnet Owner’s Manual with you to reference for this installation.
Conversion Kit Installation:
1. Shut the gas supply off at the
shut-off valve upstream of the unit.
CAUTION: The gas supply must
be shut off prior to disconnecting
the electrical power and before
proceeding with the conversion.
Allow the valve and unit to cool down
to room temperature.
Figure 1: Door Release.
Figure 2: Door Removal.
2. Remove the glass door by placing the hooked end of the door release
tool in the hole on the door latch mechanism (see Figure 1) and pulling
the latch out then up over the lip on the door. When the two (2) latches
have been released, tilt the door forward and then lift up to unhook the
bottom door tabs. (see Figure 2).
Figure 4: Burner Removal.
3. Carefully remove the log set and ember
material if they are installed.
4. Using a T-20 screwdriver, remove the four (4) screws that
hold the burner in place (pointed out in Figure 19). Slide
the burner to the left (see Figure 4), then up and out of the
rebox.
Figure 3: Unfastening Burner.
2
Figure 7. Ignition assembly.
5. Convert the burner orice:
a) Remove the main burner orice
with a inch deep socket (see
Figure 5).
b) Put a bead of pipe-thread
sealant or approved Teon tape on
the orice threads before installing
into the brass elbow.
c) Install the new orice from the
kit into the brass elbow (see Figure
6).
Figure 8: Turn Pilot Head.
d) Turn the pilot head a turn
clockwise; back to its original position.
e) Close the front of the pilot shield.
7. Convert the gas regulator:
a) If unit is installed, pull the Sonnet
out from the replace. Ensure you do
not damage any of the venting or the
unit itself.
b) Using a
7
/8” wrench, remove the
brass nut at the back left of the unit
(shown in Figure 10). A small black
spring depressor is clipped into the back of the brass nut.
c) Set the black spring depressor according to the gas used. The black spring depressor has two (2)
teeth at each end that t in to the brass nut but only one end has a larger disc. If the disc sits inside
the cap then the valve is set for natural gas and if the disc is pointing out then the valve is set for
propane (see Figure 11).
d) Reinstall the spring depressor and brass nut onto the unit.
e) Install the unit back into the replace. Check the venting and the unit itself are correctly
installed.
Pilot/
Orifice
Ignitor
Thermocouple
Figure 5: Orice Removal. Figure 6: Orice Replacement.
6. Convert the pilot:
a) Open the front of the pilot shield.
b) Using a
7
/16” wrench, turn the pilot head a turn counter-clockwise (shown in Figure 8).
c) Push the slider, with your nger or at head screwdriver, to the left if it is to be set for natural gas
or to the right for propane, red on the slider will be visible (see Figure 9).
Figure 11: Set Gas Type for
Valve.
Figure 10: Remove Brass Cap.
Figure 9: Set Gas Type to LP for
Regulator.
NG
LPG
3
8. Reinstall the burner (reversing the procedure in step 4), log set & embers (refer to SECONDARY
INSTALLATION - INSTALLING LOG SET AND EMBERS in your Sonnet Owner’s Manual), and glass door. Note:
When installing the burner, the venturi shutter rod should slip into the venturi shutter adjustment
hole.
Warning: Never run the unit without the glass door
installed.
9. Open the shut-off valve at the gas line to the unit.
10. Use a small brush to apply a warm soapy water solution to all
gas connections (use half dish soap and half warm water). If
Figure 13: Adjust Venturi Air
a gas leak is present, bubbling will occur. Gas leaks
can be repaired by using an approved pipe thread
sealant or approved Teon tape. NEVER USE AN
OPEN FLAME WHEN TESTING FOR LEAKS. Check
the gas pressure of the appliance, refer to INITIAL
INSTALLATION - GAS LINE CONNECTION in your Sonnet
Owner’s Manual and Table 1.
11. Reconnect the electrical power to the unit.
12. Light the pilot and check for proper ames (see
Figure 12). Light the burner in both the “HI” and
“LO” positions to verify proper burner ignition and
Figure 12: Pilot Flame.
operation and proper ame appearance. The amount of air to the venturi may need to be adjusted
using the rod under the rebox. Pull the rod forward for more air or push it in for less air (see Figure
13). Also refer to Figure 14 for a ame appearance picture.
13. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit
has been converted to a different fuel type.
Figure 14. Sonnet burning.
Part Number Part Description
50-1445 Sonnet Conversion Kit LP To NG Maxitrol
50-1446 Sonnet Conversion Kit NG To LP Maxitrol
MANUFACTURED BY:
SHERWOOD INDUSTRIES LTD.
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
www.envirore.biz
November 7, 2006
C-11195
4
Table 1: Orice and Pressure Information.
Main Burner Natural Gas Propane Gas
Orice: #42 DMS #54 DMS
Manifold Press: 4.0 W.C. (0.99 KPa) 10.0 W.C. (2.47 KPa)
Min. Manifold Press: 0.2 W.C. (0.05 KPa) 2.3 W.C. (0.57 KPa)
Max. Supply Press: 7.0 W.C. (1.74 KPa) 13.0 W.C. (3.28 KPa)
Min. Supply Press: 5.0 W.C. (1.24 KPa) 12.0 W.C. (2.96 KPa)
Max. Input: 26,600 BTU/hr (7.79 KW) 21,300 BTU/hr (6.24 KW)
Min. Input: 6,500 BTU/hr (1.9 KW) 11,400 BTU/hr (3.34 KW)
NEVER USE AN OPEN FLAME FOR LEAK TESTING.
-
1
-
2
-
3
-
4
Sherwood 50-1445 Installation guide
- Category
- Cookers
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Enviro 50-1472 User manual
-
-
-
-
-
-
-
-
-