Page is loading ...
POWX075100 EN
Copyright © 2019 VARO P a g e | 1 www.varo.com
1 APPLICATION ................................................................................ 2
2 PACKAGE CONTENT LIST (FIG. 1) .............................................. 2
3 GENERAL POWER TOOL SAFETY WARNINGS ......................... 2
4 ASSEMBLY INSTRUCTIONS (FIG. 2-8) ........................................ 3
5 HOW TO LEVEL THE STAND (FIG. 9) .......................................... 3
6 TECHNICAL DETAILS .................................................................... 3
POWX075100 EN
Copyright © 2019 VARO P a g e | 2 www.varo.com
STAND
POWX075100
1 APPLICATION
This stand is designed as support for the mitre saws POWX07555, POWX07559S,
POWX07560S, POWX07567S, POWX07569S, POWE50002, POWX07557T, POWX07562,
POWX07568TX, POWX07565T, POWX07554, POWX07573T, POWX0782, POW8005,
POWXQ5330, POWXQ5335, POWXQ5350 and +/- 95% of other mitre saws on the market.
WARNING! Read this manual and general safety instructions carefully
before using the appliance, for your own safety. Your power tool should
only be passed on together with these instructions.
2 PACKAGE CONTENT LIST (FIG. 1)
▪ Remove all packaging materials.
▪ Remove remaining packing and package inserts (if included).
▪ Check that the package contents are complete.
▪ Check the appliance, the power cord, the power plug and all accessories for transportation
damage.
▪ Keep the packing materials as far as possible till the end of the warranty period. Dispose it
into your local waste disposal system afterwards.
WARNING: Packaging materials are not toys! Children must not play with
plastic bags! Danger of suffocation!
4 x rubber pad
1 x adjustable foot with nut
4 x leg
2 x bottom side brace
2 x bottom cross brace
2 x top long brace
2 x tool mount
2 x top short brace
2 x bolt M6x35
2 x bolt M6x45
32 x nut M6
8 x locknut
4 x washer Ø6
36 x bolt M6x12
4 x clamping plate
1 x manual
If any parts are missing or damaged, please contact your dealer.
3 GENERAL POWER TOOL SAFETY WARNINGS
▪ Read and thoroughly understand this manual and the instruction manual of the tool you
use before performing the following.
▪ Before installing a tool on this stand, always switch off and unplug the tool.
▪ Before operating the tool, secure it to stand using bolts.
▪ Do not use the stand on uneven or unstable surface.
▪ Do not climb, sit or stand on the stand.
▪ Do not allow children in the work area.
▪ All connections should be tight and hardware tightened.
▪ When using this product, remember do not expose power tools to rain or wet conditions.
▪ When operating a power tool outside, use an outdoor extension cord. These extension
cords are rated for outdoor use, and reduce the risk of electric shock
▪ Do not modify this tool to perform a task for which it was not designed.
▪ Do not exceed the Tool Stand’s maximum weight capacity.
POWX075100 EN
Copyright © 2019 VARO P a g e | 3 www.varo.com
▪ Do not let children stand on or play with the Heavy Duty Tool Stand.
4 ASSEMBLY INSTRUCTIONS (FIG. 2-9)
NOTE: assembly of the stand and mitre saw must be done by using locknuts M6 (8), do not
use any other nuts.
Note: when the machine is mounted on the table, use M6*45mm bolts only there where base
support is thicker (front or rear). Always check that the turntable is not blocked in position
45°L or R by the assembly nuts.
5 HOW TO LEVEL THE STAND (FIG. 10)
▪ First loosen the nut (b). Turn the adjustable foot (a) clockwise to retract Foot or counter-
clockwise to extend it. Adjust the adjustable foot until the stand is level and all four legs
are in contact with the floor. Tighten the nut securely.
6 TECHNICAL DETAILS
Type
POWX075100
Max. height
800 mm
Table size
430 mm x 460 mm
/