Dishwasher DBI654IBOPERATING INSTRUCTIONS
Contents
2Front panel
3Safety instructions
4Before washing for the first time
5Loading the dishwasher
8Using the dishwasher
12Settings
14Care and cleaning
16Troubleshooting
19Technical information
20Installation
24ASKO Service
25Information for test institute
26Your notes
28Quick guide
Dear Customer,
Thank you for choosing this quality product from ASKO.
We hope it will meet your expectations and fulfil your needs for many years to come. Scandinavian design combines clean
lines, everyday functionality and high quality. These are key characteristics of all our products and the reason they are
greatly appreciated throughout the world.
To get the most out of your new dishwasher, we recommend that you read the Operating Instructions before using the dish-
washer. The last page also includes a Quick guide.
Front panel
To switch on the dishwasher, press and hold the main power switch until the display lights up.
"Welcome to your new ASKO. This is a first time set up." is shown on the display the first time the dishwasher is switched on. It
is important that you choose the right settings to ensure good dishwashing results. See page 4.
Eco
Speed mode
2:00
START
STOP
Display Start/Stop
Program mode selector
Navigation buttons for selecting a program
Option Delayed Start
Option Extra Dry
Main power switch
2
Safety instructions
• Read the operating instructions and keep
them in a safe place!
• Number of place settings: 15
• Never use the dishwasher for any purpose
other than that specified in these operating
instructions.
• Do not load the dishwasher door or dishwash-
er baskets with anything other than dishes.
• Never leave the dishwasher door open as
someone may trip on it.
• Use only dishwasher detergent!
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruc-
tion concerning use of the appliance by a
person responsible for their safety.
• If the supply cord is damaged, it must be re-
placed by a special cord or assembly avail-
able from the manufacturer or its service
agent.
• Damaged mains cables must only be re-
placed by a qualified electrician.
• Only use the dishwasher in domestic house-
hold environments for dishwashing household
dishes. All other use is prohibited.
• Never place dishes with solvent residues in
the dishwasher due to the risk of explosion.
Nor may dishes that contain ash, wax or lubri-
cants be washed in the dishwasher.
WARNING!
Knives and other pointed items must be placed
with the points down in the cutlery basket or
horizontally in other baskets.
Installation
See the chapter Installation.
Child safety
•
Always start the dishwasher immediately after
adding detergent.
•
Keep children away from the dishwasher when
the door is open. Some detergent may remain
inside!
•
Do not allow children to use or play with the
dishwasher. Be especially vigilant when the
door is open.
WARNING!
Dishwasher detergents are strongly alkaline.
They can be extremely dangerous if swallowed.
Avoid contact with skin and eyes and keep
children away from the dishwasher when the
door is open. Seek medical attention if swal-
lowed.
Check that the detergent compartment is
empty after completion of the wash cycle.
Activate child lock (Kid Safe™)
You can activate the child lock (button lock) to prevent children from
starting the dishwasher. See the chapter Settings.
Winter storage/transport
• Store the dishwasher where the temperature remains above freezing.
• Avoid long transport distances in very cold weather.
• Transport the dishwasher upright or laying on its back.
Overflow guard function
The overflow protection starts pumping out the machine and turns off
the water supply if the water level in the dishwasher exceeds the normal
level. If the overflow protection is triggered, turn off the water supply
and call the service department.
Packing material
The packaging protects the product during transport. The packaging
material is recyclable. Separate the different packaging materials to
help reduce raw material use and waste. Your dealer can take the
packaging for recycling or direct you to the nearest recycling centre.
The packaging is comprised of:
• Corrugated cardboard made from up to 100% recycled material.
• Expanded polystyrene (EPS) with no added chlorine or fluorine.
• Supports made from untreated wood.
• Protective plastic made from polyethylene (PE).
Disposal
• When the dishwasher has reached the end of its service life and is
to be disposed of, it should immediately be made unusable. Pull
out the power cable and cut it as short as possible.
• The dishwasher is manufactured and labelled for recycling.
• Contact your local authority for information about where and how
your dishwasher should be correctly recycled.
3
Before washing for the
first time
1. Checking water hardness
Contact the local water utility to check the water hardness in your area.
This is important with regard to how much detergent and rinse aid to
use.
2. Basic settings
To switch on the dishwasher, press and hold the main power switch
until the display lights up.
"Welcome to your new ASKO. This is a first time set up." is shown
on the display. It is important that you choose the right settings to en-
sure good dishwashing results.
Confirm setting
Select setting
Main power switch
Settings
Language1
Select the language to be shown on the display.
Rinse aid 0/1/2/3/4/52
By using rinse aid you will improve your drying result. You will also
achieve a better dishwashing result with glassware and dishes.
Select rinse aid dosage. The rinse aid dispenser can be adjusted
between 0 (Off) and 5 (High dosage).
Pre-selected at factory: 5
To change the chosen setting, see the chapter Settings.
4
3. Top up with rinse aid
By using rinse aid you will improve your drying result. You will also
achieve a better dishwashing result with glassware and dishes.
Press to open
1 Open the rinse aid compartment lid.
2 Carefully top up with rinse aid. Only add rinse aid to the level marked
max.
3 Wipe up any splashes of rinse aid around the compartment.
4 Close the lid firmly.
Top up rinse aid
When the rinse aid needs topping up, the above symbol lights on the
display.
After topping up, it may take a while before the symbol goes out.
NOTE!
Increase the rinse aid dosage:
• If the dishes have water marks.
Decrease the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the rinse aid can be
diluted 50:50 with water.
NOTE!
For water with a hardness greater than 10–12 °dH, you ought to use
rinse aid with citric acid (known as acid rinse aid).
Loading the dishwasher
Energy-efficient dishwashing
Run programs only with a full load
Wait to run a program until the dishwasher is full. This way you save
energy. Use the Rinse and hold program to rinse the dishes if there
are any unpleasant odours while you wait for the dishwasher to become
fully loaded.
Run programs at a lower temperature
If the dishes are only slightly dirty, you can select a program with a low
temperature.
Select Green mode
The dishwasher has different program modes. To save energy and
water, use Green mode.
Better drying results are achieved if you open the door a little once the
program has ended. (If the dishwasher is built-in, the surrounding
cabinets must be resistant to any condensation from the dishwasher.)
Do not rinse under running water
Simply scrape off large food particles before loading the dishwasher.
Choose a green detergent
Read the environmental declaration on the packaging!
Connect to cold water
Connect the dishwasher to the cold water supply if the building is
heated using oil, electricity or gas.
Connection to hot water supply
Connect the dishwasher to the hot water supply (max. 70 °C) if the
building is heated using an energy-efficient means such as district
heating, solar power or geothermal power. Choosing a hot water con-
nection cuts dishwashing times and reduces the dishwasher's energy
consumption.
NOTE!
Do not exceed the permitted water supply temperature. Certain ma-
terials used in some cookware cannot withstand high heat.
5
Fragile dishes
Some cookware is not dishwasher safe. This can be for several reasons.
Some materials cannot withstand strong heat, others can be damaged
by dishwashing detergent.
Exercise caution with, for example, handmade items, fragile decoration,
crystal/glassware, silver, copper, tin, aluminium, wood and plastic.
Look for the "Dishwasher safe" marking.
Fragile decoration
Porcelain with decoration on top of the glazing (the items feel rough)
should not be washed in a dishwasher.
Crystal/Glass
Wash fragile items made of crystal/glass, such as crystal glass from
Orrefors, using the gentle dishwashing program Crystal glass. Remem-
ber to use only a small amount of detergent and to place items so that
they do not touch each other during the wash.
By using rinse aid you will improve your drying result. You will also
achieve a better dishwashing result with glassware and dishes.
Hand-painted glassware, as well as antique and very fragile items,
should not be washed in a dishwasher.
Silver
Silver and stainless steel items should not come into contact, as the
silver can become discoloured.
Aluminium
Aluminium can lose its shine if washed in a dishwasher. However, good
quality aluminium pans can be washed in a dishwasher, even if some
of the shine will be lost.
Cutlery with glued handles
Some types of glue are not dishwasher safe. In such cases, the handles
may loosen.
Points to consider
• All dirty surfaces should face inwards and downwards!
• Dishes should not be placed in or on each other.
• Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
• Make sure small items cannot fall through the dishwasher basket;
place them in the top cutlery tray.
NOTE!
Check that the spray arms can rotate freely.
The dishwasher's baskets
The dishwasher is equipped with a top cutlery tray, an upper basket
and a lower basket with a cutlery basket.
The appearance of the baskets may differ depending on the dishwasher
setup.
Top cutlery tray
The top cutlery tray has space for cutlery, ladles, whisks, serving cutlery
and similar items.
Raising the top cutlery tray
1 Pull out the top cutlery tray.
2 Pull the two locking handles on either side forward to raise the top
cutlery tray.
Lowering the top cutlery tray
1 Make sure the upper basket is in the lowest position.
2 Pull out the top cutlery tray.
3 Slide the two locking handles on either side downwards and back-
wards to lower the top cutlery tray.
Upper basket
Place glasses, cups, bowls, side plates and saucers in the upper
basket. All dirty surfaces should face inwards and downwards! Wine
6
glasses are placed on the wine glass shelf and knives are placed in
the knife stand on the right (if fitted).
Raising the upper basket
1 Pull out the upper basket.
2 Grab the sides of the upper basket with both hands and lift it up.
Lowering the upper basket
1 Pull out the upper basket.
2 Pull out the two locking handles on either side to lower the upper
basket.
Lower basket
Place plates, side plates, serving dishes, pots and cutlery (in the cutlery
basket) in the lower basket.
Place pots and pans in the rear right part of the lower basket to achieve
the best dishwashing results from the rear of the two spray nozzles
(WideSpray™), which are intended for these types of dishes.
Foldable tines
Lower the foldable tines (plate supports) when washing pots and pans.
Release the foldable tines by pressing the catch inwards before adjust-
ing their position.
Washing large plates
Move the foldable tines and their mounts to widen the distance between
the tine rows to adapt the lower basket to plates with a diameter greater
than 25 cm.
Cutlery basket
Place cutlery with the handles facing down, except for knives, and
spread them out as much as possible. Ensure that spoons do not stack
inside each other.
The cutlery basket is best placed in the middle at the front of the lower
basket to achieve the best dishwashing performance from the unique
spray nozzle (Power Zone Cutlery™), which is intended for the cutlery
basket.
WARNING!
Knives and other pointed items must be placed with the points down
in the cutlery basket or horizontally in other baskets.
Fold-down section for small items
The cutlery basket has a fold-down section in the middle for small
items, or small shafts, such as electric whisk attachments.
7
Cutlery basket with lid
The cutlery basket lid can be removed and used, for example, as an
extra cutlery basket in the upper basket (see below).
Accessory
Buy an extra cutlery basket. The extra cutlery basket is flexible and
can be dismantled and attached to the lower basket or the large cutlery
basket to make an extra large cutlery basket. This accessory is avail-
able where you purchased your dishwasher.
2
1
Using the dishwasher
Add detergent
Press to open
1 Prewash detergent compartment
2 Main wash detergent compartment
Detergent is added according to water hardness.
Follow the instructions on the detergent packaging.
Too much detergent can result in less effective dishwashing and also
entails greater environmental impact.
The detergent compartment must be dry when adding detergent. There
is one compartment for the prewash and one for the main wash. If
powder or liquid dishwasher detergent is used, add a small amount
of the detergent to the prewash compartment. Contact the detergent
manufacturer if you have questions about the detergent.
NOTE!
Use only dishwasher detergent! Washing up liquid must not be used
as the foam that forms prevents the dishwasher from operating effec-
tively.
Dishwasher tablets
Halve the tablet if it is difficult to close the dispenser lid. There is a risk
that the detergent will not be released properly if the lid is tight and
will not open correctly.
NOTE!
Dishwasher tablets are not recommended for short programs (less
than 75 minutes). Use powder or liquid dishwasher detergent instead.
All-in-one detergent
There are many types of all-in-one detergents on the market. Read the
directions for these products carefully.
NOTE!
Optimal washing and drying results are achieved by using regular
dishwashing powder or liquid detergent with separately dispensed
rinse aid.
8
Eco
Speed mode
2:00
START
STOP
Starting the dishwasher
Select a program mode Select any options
Press and hold the main power switch until the display lights up.
Select the program
The main power switch
Press and hold the main power switch until the display turns on. Also
check that the water tap is on.
Select a program
To select a program, press the Navigation button or until the desired
program is shown on the display.
Choose a programme to suit the type of dishes and how dirty they are.
ECO wash
Use when you want to save water and energy. For normally soiled load,
such as plates, serving dishes, cups, glasses and so on.
Heavy wash
Use to wash normally soiled load, such as plates, serving dishes, cups,
glasses and so on.
Auto wash
The dishwasher can measure how dirty the dishes are and adjust water
consumption and temperature accordingly. When newly installed, the
program needs to be run five times before it is fully adapted and can
provide the best results.
Sanitation wash
Program for very dirty dishes, such as pans, casserole dishes and
oven dishes. If these dishes do not completely fill the dishwasher, you
can add plates and the like.
Time program
The program adapts to the specified running time or finish time. With
this program it is important to choose a time suited to how dirty the
dishes are.
Slightly dirty dishes0:15-0:45
Normally dirty dishes1:00-1:30
Very dirty dishes2:00-2:30
– To set the desired program time, press and hold the option
button.
Rinse and hold
Used to rinse dishes while you wait for the dishwasher to become fully
loaded.
Plastic wash
A program intended for washing plastic items that are dishwasher safe.
This program has an extra long drying cycle. Porcelain and glasses
can also be washed.
Hygiene wash
This program is designed to meet strict hygiene demands.
Crystal glass
A gentle dishwashing program with a low temperature for washing
fragile items made of crystal/glass, such as crystal glass from Orrefors.
Remember to use only a small amount of detergent and to place items
so that they do not touch each other during the wash. See also Fragile
dishes in the chapter Loading the dishwasher. Porcelain that has just
been used without dried-on leftovers can also be washed using this
program.
Quick Pro wash
Shorten the dishwashing program by preheating the water. This pro-
gram is not intended for dried-on leftovers. Remember to scrape off
larger food particles before loading the dishwasher.
1 To initiate the timer program, press and hold Start/Stop until the
display shows "Preheating". Close the door. Wait until the status
light turns green and the display shows "Preheating ready".
You can load the dishes while the water is being preheated.
2 To start the program, press and hold Start/Stop until the display
shows "Program started, close door". This indicates that the dish-
washer is ready to start. Close the door properly, otherwise the
dishwasher will not start.
Self-cleaning
Self-cleaning programme for hygienic cleaning of the dishwasher tub,
spray arms and spray pipes.
This programme can be run (with no dishes in the machine) using
normal dishwasher detergent or citric acid. Special dishwasher
cleaners are also available on the market. For the removal of limescale
deposits, see The dishwasher tub in the chapter Care and cleaning.
Upper half wash
You can use this program if you only have cups and glasses that need
washing in the upper basket. Slightly dirty dishes can also be placed
in the lower basket.
Lower half wash
You can use this program when you only want to wash plates and
cutlery in the lower basket. Slightly dirty dishes can also be placed in
the upper basket.
Select a program mode
To select a program mode, press the program mode selector until the
desired mode is shown on the display. The available program modes
vary between programs.
For a brief description, press and hold the program mode button.
Green mode
The dishwasher uses less energy and water. The program time is ex-
tended.
Speed mode
The program time is shortened, but the dishwasher uses more energy
and water.
9
Night mode
Lower noise level during the dishwashing program. The program time
is extended.
Intensive mode
Improves the dishwashing results, but the dishwasher uses more energy
and water. The program time is extended.
Select an Option
To select an option, press the option button until the desired option is
shown on the display. The available options vary between programs.
Extra Dry
A higher temperature in the final rinse and a longer drying cycle im-
prove the drying results if you activate this option. Energy consumption
is slightly increased.
For a brief description, press and hold the button for Extra Dry.
Delayed Start
When you select Delayed Start, the dishwasher will start in 1-24 hours
after you have pressed the button Start/Stop and closed the door.
1 Press the button once to activate Delayed Start. Press the button
several times – or hold it in – to set the desired number of hours.
2 Press Start/Stop and close the door. The timer counts down and
the dishwasher starts after the selected delay.
If you want to cancel the Delayed Start option, open the door and press
and hold the main power switch until the display turns off.
START
STOP
Starting the dishwasher
Press and hold Start/Stop until the display shows “Program started,
close door”. This indicates that the dishwasher is ready to start. Close
the door properly, or the dishwasher will not start.
If the dishwasher is not started or the door is not closed within 2 minutes
of the last button press, the machine switches off.
Time remaining
Once you have chosen a program, a program mode and options, the
time the program took when last used is displayed.
Status light™
Status light
The status light at the bottom of the dishwasher provides information
by means of 3 different colours.
Blue - Load more
The program has started, but you can still load more dishes.
Red - Do not load
You should not load any more dishes (risk of poorer dishwashing result).
Flashing red indicates a problem. See also Chapter Troubleshooting.
Green - Unload
The dishwashing program is finished. Standby light for 60 minutes.
Stopping or changing a program
If you want to change program after starting the dishwasher, open the
door then press and hold Start/Stop for three seconds. Add more de-
tergent if the lid of the detergent dispenser has opened. Then choose
a new program, press Start/Stop and close the door.
If you want to load more dishes
Open the door. The dishwasher stops automatically. Add the dishes
and close the door. After a while, the dishwasher continues the pro-
gram.
If the dishwasher is turned off due to a
power failure
If the dishwashing program was not finished, the interrupted program
continues when power is restored.
NOTE!
During drying, the program is interrupted if the power is cut or the
door is open for more than 2 minutes.
How to get the best drying results
• Fully load the dishwasher.
• Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
• Top up with rinse aid or increase the rinse aid dosage level.
• Activate the Extra Dry option.
• Open the door a little once the program has finished.
• Allow the dishes to cool before unloading the dishwasher.
Once the program has finished
Once the program has finished and the door is opened "Ready" appears
on the display.
At the end of the program, you will hear a short beep. Chapter Settings
describes how to change this function.
The end of the program is also indicated by the status light turning
green.
The dishwasher switches off automatically after the program ends.
Turn off the water tap after each use.
Unloading the dishwasher
Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher
before unloading them.
Unload the lower basket first to avoid any water drops from the upper
basket falling onto the dishes in the lower basket.
10
Program chart
Consumption values
1)
Final rinseNumber of rins-
es
Main washPrewashesDetergent, com-
partment 2
(ml)
Program
Water cons.
(liter)
Hot water
3)
Cold water
2)
Energy
(approx. kWh)
Dishwashing
time
(approx.
hrs:min)
Energy
(approx. kWh)
Dishwashing
time
(approx.
hrs:min)
12.20.52:300.82:5048 °C348 °C225
ECO wash
4)
140.62:051.12:2565 °C260 °C225Heavy wash
11-200.5-1.01:50-2:300.9-1.52:10-2:7065 °C2-350-65 °C1-325Auto wash
140.61:351.11:5565 °C260 °C225Sanitation wash
11-190.4-1.20:15-2:300.5-1.60:15-2:30<65 °C2-3<65 °C0-225Time program
30.010:070.010:07--- °C1Rinse and hold
120.52:050.92:2565 °C250 °C125Plastic wash
100.91:001.41:1070 °C270 °C25Hygiene wash
90.51:200.81:4050 °C245 °C20Crystal glass
100.60:501.11:0055 °C260 °C20Quick Pro wash
120.62:001.22:2060 °C260 °C120Upper half wash
120.62:001.22:2060 °C260 °C120Lower half wash
1)
Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions and more.
2)
Connection to cold water, approx. 20 °C.
3)
Connection to hot water, approx. 60 °C.
4)
The energy label performance figures are based on this program which is recommended for normally soiled load (no options).
11
Settings
Open the dishwasher's Settings menu
To open the dishwasher's Settings menu, press the Navigation button or until Settings menu is shown on the display and confirm your selection
using the mode selector .
To exit the dishwasher's Settings menu, select Exit and confirm your selection using the mode selector .
START
STOP
1� Language
English
Mode selector to confirm current setting
Settings Current setting
Navigation buttons for choosing setting
OptionsSettings
You can choose the language used for the display.English GB/English AU/English US/
Svenska/Dansk/Norsk/Suomi/Deutsch
/Italiano/Nederlands/Français/Español
Language1.
Programs can be shown or hidden in the menu. Choose between
On and Off.
Heavy wash On/Off
ECO wash On/Off
Auto wash On/Off
Sanitation wash On/Off
Time program On/Off
Rinse and hold On/Off
Plastic wash On/Off
Hygiene wash On/Off
Crystal glass On/Off
Quick Pro wash On/Off
Self-cleaning On/Off
Lower half wash On/Off
Upper half wash On/Off
Select programs2.
You can activate the child lock (button lock) to prevent children
from starting the dishwasher.
On/OffChild lock3.
To temporarily deactivate or activate the child lock, press and
hold the left Navigation button and the option button Delayed Start
for 3 seconds.
For adjusting the contrast of the display.Contrast top display1/2/3/4Display settings4.
Setting to hide the logo shown on the display.Logo in top display On/Off
This sound is used to confirm each button press.0/1/2/3Feedback sound5.
The buzzer indicates when a dishwashing program has ended.0/1/2/3Buzzer volume6.
Error messages are always indicated by a loud buzzer.
Setting for rinse aid dosage. The rinse aid dispenser can be adjust-
ed between 0 (Off) and 5 (High dosage).
0/1/2/3/4/5Rinse aid7.
Increase the rinse aid dosage:
• If the dishes have water marks.
Decrease the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the rinse aid can
be diluted 50:50 with water.
12
OptionsSettings
Super rinse adds two extra rinses.On/OffSuper rinse8.
Activated in the following programs:
Heavy wash
ECO wash
Sanitation wash
Plastic wash
Lower half wash
Upper half wash
Activate the setting High temperature to improve the dishwashing
results. Energy consumption is slightly increased.
On/OffHigh temperature9.
Activated in the following programs:
Heavy wash
ECO wash
Sanitation wash
Plastic wash
Quick Pro wash
Lower half wash
Upper half wash
13
Care and cleaning
Coarse filter
The coarse filter traps larger food particles, which cannot get past the
drainage pump. Empty the coarse filter as necessary.
Coarse filter
1 Lift the coarse filter by the handle.
2 Empty the coarse filter. Remember to replace it!
Fine filter
Debris that collects on the fine filter is automatically rinsed away during
each wash. Clean the fine filter when necessary.
Fine filter
1 Turn the handle anticlockwise.
2 Lift the filter straight up using the handle. Free the coarse filter to
clean the fine filter.
3 Replace in reverse order. Check that the edges seal properly when
replacing the fine filter.
4 Lock the filter in place by turning the handle clockwise to the stop
position. The handle should point straight out from the dishwasher.
NOTE!
The dishwasher must not be used without the filter in place!
Diswashing efficiency can be affected if the course filter is incorrectly
fitted. After cleaning ensure that filter handle is fully locked with the
handle pointing out of the dishwasher.
Spray arms
Holes and bearings can sometimes become blocked. Remove any
debris using a pin or something similar. The spray arms also have
holes on their undersides.
To facilitate cleaning, you can remove the spray arms. Remember to
fit them firmly back into place after cleaning.
Top spray arm
• The upper basket must be removed before the top spray arm can
be released. Pull out the upper basket and turn the basket catch
on each runner outwards (see illustration). The basket can now be
removed.
• Pull out the top cutlery tray. Press the top spray arm up and unscrew
the spray arm bearings counter-clockwise to remove the spray arm.
Upper spray arm
1 Pull out the upper basket.
2 Unscrew the spray arm bearings counterclockwise to remove the
spray arm from the upper basket.
Lower spray arm
• Pull the lower spray arm straight up to release it.
The door and the door seal
Regularly clean the sides of the door and the door seal. Use a slightly
damp cloth (with a little cleaner if necessary).
Front panel
Keep the buttons clean and free from grease. Wipe them clean with a
dry or slightly damp cloth. Never use cleaners – they can scratch the
surface. Use the main power switch to turn off the dishwasher before
cleaning the buttons to avoid activating any buttons unintentionally.
The dishwasher tub
The dishwasher tub is made of stainless steel and is kept clean through
normal use.
Limescale deposits
If you have hard water, limescale deposits may build up in the dish-
washer. If this happens, run the Self-cleaning program with two table-
spoons of citric acid in the detergent compartment (with no dishes in
the machine). Special dishwasher cleaners are also available on the
market.
14
Unblocking the drainage pump
If the dishwasher still contains water after the programme has finished,
something may be blocking the drainage pump. Such items are easily
removed.
1 Turn off the machine using the main power switch and unplug it
from the wall socket.
2 Remove the coarse filter and the fine filter.
3 Scoop out the water from the dishwasher tub.
4 In order to inspect the drainage pump, remove the coloured stop
on the right in the bottom drain.
5 Turn the pump wheel located behind the drainage pump stop by
hand. Carefully remove any items.
6 Replace the drainage pump stop along with the fine and coarse
filters.
7 Plug the machine in again.
If the dishwasher still does not start and a whirring sound is heard,
the overflow protection has been activated.
• Shut off the water.
• Remove the plug from the wall socket.
• Call the service department.
Drainage pump stop
NOTE!
Do not forget to replace the drainage pump stop.
Unblocking the inlet hose filter
If the water supply contains small particles, the outer filter on the inlet
hose may become blocked, which results in Water inlet fault.
1 Turn off the machine using the main power switch and unplug it
from the wall socket.
2 Turn off the water tap.
3 Unscrew the inlet hose.
4 Carefully remove the outer filter from the inlet hose and clean it.
5 Replace the filter and check that the gasket is correctly positioned.
6 Screw the inlet hose firmly into place.
7 Plug the machine into the wall socket and turn on the water tap.
Allow the pressure to settle for a while and check that the connection
is watertight.
Outer filter on inlet
hose
Gasket
15
Troubleshooting
ActionType of fault on the display
Clear the drainage pump. See the chapter Care and cleaning. If the problem persists, call the
service department.
Overfilling waterF10
See “Water remains in the dishwasher” in the table “Problem” below. If the problem persists, call
the service department.
Water outlet faultF11
Check whether dishwasher inlet hose is connected to a pressure limiting valve (some pressure
limiting valves may restrict the supply of water to the dishwasher).
Water inlet faultF12
Check that the water tap is on. Check that the outer filter on the inlet hose is not blocked. See
Unblocking the inlet hose filter in the chapter Care and cleaning. If the problem persists, call for
service.
Check that the water tap is on. If the problem persists, call the service department.
Turn off the water tap and call the service department.Inlet valve leakageF40
Call the service department.Water level faultF52
Turn off the water tap and call the service department.Overfilling waterF54
Call the service department.Circ. pump faultF56
Press any button to clear the error message.
ActionPossible causesProblem
Wait a moment then try again.You have pressed the buttons too soon after
opening the door.
The buttons do not react when pressed.
See the chapter Settings.Child lock (button lock) activated.
Open the door. The buttons only react to use
when the door is open.
The door is closed.
Clean with a dry or slightly damp cloth.The buttons are dirty.
Check that the baskets are correctly positioned
horizontally.
The baskets are not correctly positioned.Cannot close door.
Check that the dishes are not blocking the bas-
kets from sliding properly into place.
Press and hold Start/Stop until the display shows
"Program started, close door".
The Start/Stop start button has not been pressed
for long enough.
The dishwasher does not start.
Check.The door is not properly closed.
Close the door and wait. After a while, the dish-
washer continues the program.
You have opened the dishwasher to add more
dishes while a program is in progress.
Check.A fuse/circuit breaker has been tripped.
Check.The plug is not plugged into the wall socket.
Check.The water tap is turned off.
Check.Overflow/leaks
Turn off the water tap. Pull out the plug and call
the service department.
A whirring sound (the drainage pump) is heard
from the dishwasher and does not stop when the
main power switch is turned off.
Press and hold Start/Stop for three seconds if
you want to cancel the Delayed Start option.
Check that the Delayed Start option has not been
selected.
16
ActionPossible causesProblem
Check that the dishes are not blocking the spray
arms.
The spray arms do not rotate.The dishes are not clean.
Clean the spray arms. See Chapter Care and
cleaning.
Spray arm holes or bearings blocked.
Choose a longer programme.Unsuitable dishwashing program.
Dose according to water hardness. Far too much
or far too little detergent results in poorer dish-
washing results.
Incorrect detergent dosage.
Avoid large packages.Old detergent. Detergent is a perishable product.
Do not cover porcelain with large bowls or the
like. Avoid placing very tall glasses in the corners
of the baskets.
Dishes loaded incorrectly.
Place dishes to sit steady.Glasses and cups have toppled over during the
program.
Check that the filter handle is locked in the stop
position. The handle should point towards the
back of the dishwasher.
The filters are not fitted correctly.
Rinse off these types of foodstuffs if not starting
the dishwasher immediately. Use the Rinse and
hold program.
Some foodstuffs, such as mustard, mayonnaise,
lemon, vinegar, salt and dressings, can mark
stainless steel if left for too long.
Spots on stainless steel or silver.
In order to avoid marks and tarnishing, separate
dishes made from different metals, such as silver,
stainless steel and aluminium.
All stainless steel can cause spots on silver if
they come into contact during dishwashing.
Aluminium can also cause spots on dishes.
See the chapter Settings.Incorrect rinse aid dosage setting.Spots or films on the dishes.
Wash crystal at a low temperature and with a
conservative amount of detergent. Contact the
detergent manufacturer.
Too high temperature and/or too much detergent
can cause etching on crystal. Unfortunately, this
cannot be repaired, only prevented.
Reduce the dosage. See the chapter Settings.
If you have very soft water, you may want to dilute
the rinse aid 50:50 with water.
Rinse aid dosage setting too high.The dishes have a sticky white/blue film.
Use a detergent with a bleaching agent.Lipstick and tea can be difficult to wash off.Spots left after washing.
The detergent compartment must be dry when
adding detergent.
The detergent compartment was damp when
adding detergent.
Detergent residue in the detergent compartment
after dishwashing.
Check that the dishes are not preventing the
detergent compartment from opening.
The detergent compartment is blocked.
Check that the dishes are placed securely. Spin
the spray arms to make sure they can rotate.
The dishes are not correctly placed or the spray
arms are not rotating.
Rattling sound when dishwashing.
17
ActionPossible causesProblem
Clean the coarse and fine filters.The filters are blocked.Water remains in the dishwasher.
Check that the filter handle is locked in the stop
position. The handle should point towards the
back of the dishwasher.
The filters are not fitted correctly.
Clean the drainage pump. See the chapter Care
and cleaning.
Debris in the drainage pump.
Check that the hose is free from kinks and sharp
bends.
Kink in drainage hose.
Disconnect the drainage hose where it connects
to the sink unit's water trap. Check that no debris
has fastened and that the connection has an in-
ner diameter of at least 14 mm.
Blocked drainage hose.
Clean with washing-up brush and low foaming
cleaner.
Dirt around the seals and in corners.Bad odour in dishwasher.
Run a program with a higher temperature once
or twice a month. Or run a self-cleaning program.
See Self-cleaning in Chapter Using the dishwash-
er.
Low temperature programs have been selected
for a prolonged period.
Activate the Extra Dry option.Depending on the load, the programme's drying
cycle may be insufficient.
The dishes are not dry enough.
Fully load the dishwasher.The dishwasher is not fully loaded.
Top up with rinse aid or increase the rinse aid
dosage level. See the chapter Settings.
Rinse aid needs topping up or dosage is set too
low.
Open the door a little once the program has fin-
ished.
18
Technical information
Information on energy labelling
Energy labelling
AS/NZS 2007Australian standard:
15Number of place settings:
ECO wash
1)
, no optionsDishwashing programs:
2:50 hours:minutesProgram time:
Cold water 20 °CConnection:
IEC 60704-2-3Test method for noise measurement:
1)
This dishwashing program is the standard cleaning cycle used to compile the energy labelling information. It is intended for washing normally
dirty dishes and is the most effective program in terms of combined energy and water consumption.
Technical data
819-872 mmHeight:
596 mmWidth:
559 mmDepth:
45 kg
1)
Weight:
0.03–1.0 MPaWater pressure:
See compliance plateElectrical connection:
See compliance plateRated power:
1)
Weight can vary due to different specifications.
19
Installation
819*- 872
519
559
714
596
131-186
50 30
30-94
1198
700
670
9
[mm]
Nominal dimensions. Actual measurements may vary.
*Remove locking nuts for an installed height of 820-821 mm.
Safety instructions
• Connections to electricity, water and drainage must be performed
by a qualified professional.
• Always follow applicable regulations for water, drainage and elec-
tricity.
• Take care during installation! Wear protective gloves! There must
always be two people!
• Before screwing the dishwasher into place, test the dishwasher by
running the Rinse and hold program. Check that the dishwasher
fills with water and drains. Check also that none of the connections
leak.
WARNING!
Turn off the water supply when installing the dishwasher!
The plug must be disconnected or power to the socket turned off
while the work is carried out!
Transport protection for the door
Do not forget to remove the transport protection for the door when un-
packing the dishwasher.
REMOVE
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Asko DBI653IBBS User manual
-
-
-
-
-
-
-
-
-
Asko DFI664XXLSOF Operating instructions
Other documents
-
Gorenje GS63160WAU Owner's manual
-
Gorenje GV65260AU Owner's manual
-
KitchenAid KDFX 7017 User guide
-
-
-
-
Hisense DW30.2 Owner's manual
-
-
Gorenje DW30.2 User manual
-
KitchenAid KDFX 7015 Owner's manual