Fujitsu CELVIN NAS QE805 Operating instructions

Operating Manual System

CELVIN® NAS Server

Congratulations on your purchase of an innovative

product from Fujitsu.

Latest information about our products, tips, updates etc. can be found on the Internet at:

http://www.fujitsu.com/fts/

For driver updates, please go to: http://support.ts.fujitsu.com/download

Should you have any technical questions, please contact:

● our Hotline/Service Desk (see Service Desk list or visit:

http://support.ts.fujitsu.com/contact/servicedesk)

● your sales partner

● your sales office

We hope you enjoy working with your new Fujitsu system!

Published by / Contact address in the EU

Fujitsu Technology Solutions GmbH

Mies-van-der-Rohe-Straße 8

80807 Munich, Germany

http://www.fujitsu.com/fts/

Copyright

Publication Date

08/2014

Order No.: A26341-F103-Z306-1-7619, edition 3

CELVIN® NAS Server

Operating Manual

Your CELVIN® NAS Server … 3

Installing the NAS 9

Connecting to the NAS 30

Copying data using the front USB port 37

Web Server 39

FTP server 41

Using the QGet download software 42

NetBak Replicator 45

Firmware update 47

NAS maintenance 50

Troubleshooting RAID operation errors 55

Technical data 59

Remarks

Information on the product description meets the design specifications of Fujitsu and is

provided for comparison purposes. Several factors may cause the actual results to differ.

Technical data is subject to change without prior notification. Fujitsu rejects any responsibility

with regard to technical or editorial mistakes or omissions.

Trademarks

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its subsidiaries in

the United States and other countries.

Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation

in the United States and/or other countries.

CELVIN is a registered trademark of Fujitsu Technology Solutions GmbH.

All other trademarks specified here are the property of their respective owners.

Copyright

No part of this publication may be copied, reproduced or translated without the prior written

consent of Fujitsu.

No part of this publication may be saved or transferred by any electronic means without the

written approval of Fujitsu.

Fujitsu 1

Contents

Your CELVIN

®

NAS Server … ............................................................................................................ 3

Safety Warnings ................................................................................................................................... 3

CE marking................................................................................................................................... 3

Hardware overview............................................................................................................................... 5

CELVIN

®

NAS Server Q802 ......................................................................................................... 5

CELVIN

®

NAS Server Q902 ......................................................................................................... 7

Installing the NAS............................................................................................................................... 9

List of recommended hard disks........................................................................................................... 9

System ventilation ................................................................................................................................ 9

System status checks......................................................................................................................... 10

Use the LCD Panel............................................................................................................................. 13

View system information by the LCD panel........................................................................................ 15

System Messages .............................................................................................................................. 18

Configuring software settings ............................................................................................................. 19

Connecting a network drive........................................................................................................ 25

Connecting to the NAS..................................................................................................................... 30

Using the public folder (public network share).................................................................................... 30

Administering the NAS via a Web browser under Windows............................................................... 32

Administration user interface .............................................................................................................. 33

Opening the main menu ............................................................................................................. 34

Control Panel / Opening applications ......................................................................................... 35

Accessing the NAS from Linux........................................................................................................... 36

Copying data using the front USB port .......................................................................................... 37

Web Server........................................................................................................................................ 39

MySQL administration ................................................................................................................ 40

SQLite administration ................................................................................................................. 40

FTP server ......................................................................................................................................... 41

Using the QGet download software................................................................................................ 42

NetBak Replicator............................................................................................................................. 45

Installing NetBak Replicator ............................................................................................................... 45

Using NetBak Replicator .................................................................................................................... 46

Firmware update............................................................................................................................... 47

Updating the system firmware using Fujitsu Finder.................................................................... 48

NAS maintenance ............................................................................................................................. 50

Shutting down/rebooting the server.................................................................................................... 50

Resetting the administrator password and network settings .............................................................. 52

Failure or malfunction of a hard disk .................................................................................................. 53

Power failure or abnormal shutdown .................................................................................................. 53

Abnormal system software behaviour ................................................................................................ 53

System temperature protection .......................................................................................................... 53

EuP mode configuration (for compliance with legal standby requirements)....................................... 54

Troubleshooting RAID operation errors......................................................................................... 55

Hot-swap Hard Drives ........................................................................................................................ 56

RAID Recovery................................................................................................................................... 57

Technical data................................................................................................................................... 59

Contents

2 Fujitsu

GNU GENERAL PUBLIC LICENSE...................................................................................................61

Your CELVIN® NAS Server …

Fujitsu 3

Your CELVIN

®

NAS Server …

Thank you for purchasing a CELVIN

®

NAS Server. These operating instructions provide detailed

information on the use of this product. Please read the instructions carefully to enjoy the full benefit

of the powerful functions offered by the CELVIN

®

NAS Server.

Safety Warnings

!

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to

the manufacturer’s instructions.

Do NOT touch the fan inside the system to avoid serious injuries.

● The NAS can operate normally in the temperature of 0ºC–40ºC and relative humidity of

0%–95%. Please make sure the environment is well-ventilated.

● The power cord and devices connected to the NAS must provide correct supply voltage (100W,

90–264V).

● Do not place the NAS in direct sunlight or near chemicals. Make sure the temperature and

humidity of the environment are in optimized level.

● Unplug the power cord and all connected cables before cleaning. Wipe the NAS with a dry

towel. Do not use chemical or aerosol to clean the NAS.

● Do not place any objects on the NAS for the server’s normal operation and to avoid overheat.

● Use the flat head screws in the product package to lock the hard disks in the NAS when

installing hard disks for proper operation.

● Do not place the NAS near any liquid.

● Do not place the NAS on any uneven surface to avoid falling off and damage.

● Make sure the voltage is correct in the location where the NAS is installed. Contact the

distributor or the local power supply company for the information.

● Do not place any object on the power cord.

● Do not attempt to repair the NAS in any occasions. Improper disassembly of the product may

expose the users to electric shock or other risks. For any enquiries, please contact the

distributor.

● The chassis NAS models should only be installed in the server room and maintained by the

authorized server manager or IT administrator. The server room is locked by key or keycard

access and only certified staff is allowed to enter the server room.

CE marking

CE marking for devices without wireless component supplied at launch from

20.07.2007

The shipped version of this device complies with the requirements of EC directive

2004/108/EC "Electromagnetic Compatibility", 2006/95/EC "Low voltage directive" and

2009/125/EC “Ecodesign Directive“.

Your CELVIN® NAS Server …

4 Fujitsu

i

The CELVIN® NAS Server will subsequently also be referred to by the short names NAS,

Q802 (model with 4 hard disks) or Q902 (model with 6 hard disks).

!

Back up your system regularly to avoid any potential data loss.

Fujitsu Technology Solutions will not accept responsibility for the loss of or the recovery of

any data in any form.

Q802

Q902

i

Further information, such as data sheets, frequently asked questions and tutorials, can be

found on the Internet at www.celvin.com.

Your CELVIN® NAS Server …

Fujitsu 5

Hardware overview

CELVIN

®

NAS Server Q802

Front

POWER

ENTER

SELECT

COPY

1

2

3

6

7

4

5

STATUS LAN USB eSATA

1 = LED indicators: Status, LAN, USB, eSATA

2 = LED indicators: HDD 1-4

3 = ON/OFF switch

4 = One Touch Copy button

5 = USB 2.0

6 = Enter button

7 = Select button

Your CELVIN® NAS Server …

6 Fujitsu

Rear

1

2

3

4

5

6

7

8

9

1 = Power supply

2 = HDMI (reserved)

3 = VGA (reserved for service purposes)

4 = Reset button for password and network settings

5 = USB 3.0 x 2

6 = USB 2.0 x 4

7 = Gigabit LAN x 2

8 = eSATA x 2

9 = Security Lock slot

Your CELVIN® NAS Server …

Fujitsu 7

CELVIN

®

NAS Server Q902

Front

ENTER

SELECT

POWER

COPY

STATUS LAN USB

eSATA

6

7

8

1

2

3

4

5

1 = LED indicators: Status, LAN, USB, eSATA

2 = LED indicator: Power supply

3 = ON/OFF switch

4 = One Touch Copy button

5 = USB 2.0

6 = Enter button

7 = Select button

8 = LED indicators: HDD 1-6

Your CELVIN® NAS Server …

8 Fujitsu

Rear

1

2

3

4

5

6

7

8

9

1 = Power supply

2 = HDMI (reserved)

3 = VGA (reserved for service purposes)

4 = Reset button for password and network settings

5 = USB 3.0 x 2

6 = USB 2.0 x 4

7 = Gigabit LAN x 2

8 = eSATA x 2

9 = Security Lock slot

Installing the NAS

Fujitsu 9

Installing the NAS

For information on hard disk installation, please refer to the "Quick Start Guide".

List of recommended hard disks

This product will work with 2,5/3,5 inch SATA hard disks from major hard disk manufacturers. A list of

compatible drives can be found at http://support.ts.fujitsu.com.

!

Fujitsu Technology Solutions will accept no liability whatsoever for any product

defects/faulty operation, and/or any time and costs associated with data loss/data

recovery, insofar as the cause can be attributed to misuse or improper installation of hard

disks, regardless of the circumstances or for whatever reason.

!

Please note that when installing a hard disk (new or used) which has not previously been

installed on the NAS, the hard disk will first be formatted and sub-divided automatically,

and all disk data will be lost.

System ventilation

Please ensure when setting up the device that sufficient ventilation will be available at all times. The

air inlet on the underside of the product must not be covered, as otherwise it is not possible to

guarantee that the system will receive sufficient ventilation, which may lead to the product being

damaged.

Installing the NAS

10 Fujitsu

System status checks

The NAS is fitted with LED indicators to show the system status and further information. When the

NAS is switched on it is important to check the following items to make sure that the system is

working normally. Please note that the information provided by the LEDs described below is only

valid if the hard disks have been correctly installed and the NAS is connected to the network and the

power supply.

i

The following illustration shows the CELVIN

®

NAS Server Q902. The status indicators,

other than the power supply status indicator, are identical for both device variants.

ENTER

SELECT

STATUS LAN USB

eSATA

123456

1 = Power supply (Q902) 4 = USB

2 = System status 5 = eSATA

3 = LAN

6 = HDD 1 - 4 (Q802)

HDD 1 - 6 (Q902)

Installing the NAS

Fujitsu 11

LED Display & System Status Overview

LED Colour LED-Status Description

Flashes green

and red

alternately every

0.5 sec

● The hard disk drive on the NAS is being

formatted.

● The NAS is being initialized.

● The system firmware is being updated.

● RAID rebuilding is in process.

● Online RAID capacity expansion is in

process.

● Online RAID level migration is in process.

Red

● The hard disk drive is invalid.

● The disk volume has reached its full

capacity.

● The disk volume is going to be full.

● The system fan is out of function.

● An error occurs when accessing (read/write)

the disk data.

● A bad sector is detected on the hard disk

drive.

● The NAS is in degraded read-only mode

(2 member hard drives fail in a RAID 5 or

RAID 6 configuration, the disk data can still

be read).

● (Hardware self-test error).

Flashes red

every 0.5 sec

The NAS is in degraded mode (one member hard

drive fails in RAID 1, RAID 5 or RAID 6

configuration).

Flashes green

every 0.5 sec

● The NAS is starting up.

● The NAS is not configured.

● The hard disk drive is not formatted.

Green The NAS is ready.

System

Status

Red /

Green

Off

All the hard disk drives on the NAS are in

standby mode.

Orange The NAS is connected to the network.

LAN Orange

Flashes orange The NAS is being accessed from the network.

Flashes red

The disk data is being accessed and a read/write

error occurs during the process.

Red

A hard drive read/write error occurs.

Flashes green

The disk data is being accessed.

HDD

Red /

Green

The hard drive can be accessed.

Installing the NAS

12 Fujitsu

LED Display & System Status Overview

LED Colour LED-Status Description

Flashes blue

every 0.5 sec

● A USB device (connected to front USB port)

is being detected.

● A USB device (connected to front USB port)

is being removed from the NAS.

● The USB device (connected to the front USB

port) is being accessed.

● The data is being copied to or from the

external USB or eSATA device.

Blue

A front USB device is detected (after the device is

mounted).

USB Blue

Off

● No USB device is detected.

● The NAS has finished copying the data to or

from. the USB device connected to the front

USB port of the NAS.

Flashes The eSATA device is being accessed.

eSATA Orange

Off

No eSATA device can be detected.

Alarm Buzzer

The alarm buzzer can be disabled in Control Panel - Hardware.

i

The beep, which sounds when booting the device, cannot be deactivated.

Beep sound No. of Times Description

Short beep (0.5 sec) 1

● The NAS is starting up.

● The NAS is being shut down (software

shutdown).

● The user presses the reset button to

reset the NAS.

● The system firmware has been updated.

Short beep (0.5 sec) 3 An attempt is being made to copy NAS data

to an external storage device connected to

the front USB port, but the data cannot be

copied.

Short beep (0.5 sec)

Long beep (1.5 sec)

3, every 5 min. The system fan is out of function.

Installing the NAS

Fujitsu 13

Beep sound No. of Times Description

2

● The disk volume is going to be full.

● The disk volume has reached its full

capacity.

● The hard disk drives on the NAS are in

degraded mode.

● The user starts hard drive rebuilding.

Long beep (1.5 sec)

1

● The NAS is turned off by force shutdown

(hardware shutdown).

● The NAS has been turned on and is

ready.

Use the LCD Panel

You can use the LCD panel to perform disk configuration and view the system information.

When the NAS has started up, you will be able to view the NAS name and IP address:

NAS5F4DE3

169.254.100.100

For the first time installation, the LCD panel shows the number of hard drives detected and the IP

address. You may select to configure the hard drives.

Number of

hard drives

detected

Default disk

configuration

Available disk configuration options

1 Single Single

2 RAID 1 Single  JBOD  RAID 0  RAID 1

3 RAID 5 Single  JBOD  RAID 0  RAID 5

4 or above RAID 5 Single  JBOD  RAID 0  RAID 5  RAID 6  RAID 10

i

Press the Select button to choose the option.

Press the Enter button to confirm.

For example, when you switch on the NAS with 5 hard disks installed, the following message is

displayed on the LCD panel:

Config.Disks?

Installing the NAS

14 Fujitsu

Use the Select button to select further options, e.g. RAID 6.

Proceed as follows to select a standard drive configuration:

► Press Enter.

The following message is displayed:

Choose RAID5?

No

► Use the Select button to select Yes.

► Confirm your selection by pressing Enter.

When you execute RAID 1, RAID 5, RAID 6 or RAID 10 configuration, the system will initialize the

hard drives, create the RAID device, format the RAID device, and mount it as a volume on the NAS.

The progress will be shown on the LCD panel.

When it reaches 100 %, you can connect to the RAID volume, for example, create folders and

upload files to the folders on the NAS.

In the meantime, to make sure the stripes and blocks in all the RAID component devices are ready,

the NAS will execute RAID synchronization and the progress will be shown on Disk Management -

Volume Management page. The synchronization rate is around 30-60 MB/s (varies depending on the

hard drive models, system resource usage, etc.)

i

If a member drive of the RAID configuration is lost during synchronization, the RAID device

will switch to a degraded mode. You can continue to access the drive data.

If you insert a new member drive in the device, the drive is restored. You can check the

status on the Volume Management page.

If Encrypt Volume? is displayed on the LCD screen, select Yes if you wish to encrypt the data carrier.

The default selection is "No".

The default encryption password is admin. To change the password, login the web-based

administration interface of the NAS with an administrator account and change the settings in Disk

Management – Encrypted File System.

Encrypt VOLUME?

No

i

The data encryption functions may not be available in accordance to the legislative

restrictions of some countries.

Page is loading ...

Fujitsu CELVIN NAS QE805 Operating instructions

This manual is also suitable for

Fujitsu CELVIN NAS QE805 Operating instructions

Related papers

Other documents