ULTIMATE SPEED UPBS 8000 A1 Operating instructions

Brand: ULTIMATE SPEED

Model: UPBS 8000 A1

Category: Battery chargers

Type: Operating instructions

ULTIMATE SPEED UPBS 8000 A1: Your reliable power bank and jump starter in one device. Never get stranded with a dead battery again! This compact and portable device delivers 200A peak current and 80A starting current, making it suitable for petrol motors up to 2 liters and diesel motors up to 1.6 liters. It also features 2 USB ports for charging your mobile devices on the go.

PORTABLE JUMP STARTER WITH POWER BANK

UPBS 8000 A1

IAN 279357

SELBSTSTARTHILFE MIT

POWERBANK

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

PORTABLE JUMP STARTER

WITH POWER BANK

Operation and Safety Notes

Translation of the original instructions

GB / IE / NI Operation and Safety Notes Page 5

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 15

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

Page is loading ...

5 GB/IE/NI

Table of contents

List of pictograms used ........................................................................................................ Page 6

Introduction ................................................................................................................................... Page 6

Intended use ........................................................................................................................................ Page 6

Features ...............................................................................................................................................Page 6

Technical specifications ......................................................................................................................Page 7

Delivery Contents ................................................................................................................................Page 7

General safety instructions .............................................................................................. Page 7

Set up ..................................................................................................................................................Page 9

Monitoring the capacity of the jump start aid ................................................................................... Page 9

Charging the jump start aid ................................................................................................................Page 10

Charging the 12 V vehicle battery ..................................................................................................... Page 10

Charging mobile phones and tablets ................................................................................................Page 11

Switching on the lights ........................................................................................................................Page 11

FAQs ....................................................................................................................................................Page 11

Troubleshooting ........................................................................................................................Page 11

Cleaning ...........................................................................................................................................Page 11

Storage .............................................................................................................................................Page 11

Warranty and service information ...........................................................................Page 12

Warranty terms ...................................................................................................................................Page 12

Extent of warranty ............................................................................................................................... Page 12

Processing of warranty claims ............................................................................................................ Page 12

Environmental notes and disposal information .............................................Page 13

EC Declaration of Conformity ......................................................................................... Page 13

6 GB/IE/NI

Introduction / General safety instructionsIntroduction

Portable jump starter with

power bank UPBS 8000 A1

Introduction

Congratulations! You have purchased

one of our high-quality products. Be-

fore initial setup, please familiarise

yourself with the product. Read the following oper-

ating and safety instructions carefully. Only trained

persons may set up this product.

KEEP OUT OF THE REACH OF CHILDREN!

Only for petrol motors with a

max. 2 litre engine and for

diesel motors with a max.

1.6 litre engine.

Intended use

This power pack is designed to provide additional

support for 12 V vehicle batteries in diesel and

petrol vehicles with start-up problems, caused by

batteries that are weak, empty or have a defect.

However, the power pack cannot replace the

vehicle battery. If no more than 200 A are needed,

the power pack allows the user to single-handedly

start up the vehicle when necessary, without addi-

tional help from a third party (max. peak current).

The device also has 2 USB ports. So, if needed,

mobile phones, navigation tools or other devices

using USB ports can be charged.

Any other use can damage the device and put the

user at serious risk.

The manufacturer is not liable for damage resulting

from improper use or incorrect operation.

This device is not suitable for commercial use.

Commercial use will void the warranty.

The LED bulb is not suitable for

domestic room lighting.

-20°C

The LED bulb is suitable for extreme

temperatures below -20°C.

Features

As you are unpacking the item after

delivery, ensure that all the parts are

present and that the device is in perfect

condition. Do not use the device if it is defective.

List of pictograms used

Please read the operating

instructions!

Serious to fatal injuries possible

Note

Electric shock warning! Danger to

life!

Observe warnings and the

safety instructions!

Caution! Explosion hazard!

The LED bulb is not suitable for

domestic room lighting.

Don't waste, recycle!

-20°C

The LED bulb is suitable for

extreme temperatures below

-20°C.

Dispose of the packaging and pro-

duct in an environmentally-friendly

manner!

7 GB/IE/NI

Introduction / General safety instructionsIntroduction

SOS lights

Charging port 5 V /1A

Output USB 5 V /1A/2A

Power button

Charge status indicator lights

Car’s jump start outlet

USB power cable

Jumper cable

Power pack with vehicle jump start aid

Start LED

Error LED

Power supply adaptor

Button LED box

Technical speciﬁcations

Model: UPBS 8000 A1

Type of battery: LiFePO4

Battery capacity: 8000 mAh,

3.2–3.4 V

Charge cycles: 1500

Charge duration: up to 8 hours

Peak current: 200A

Starting current: 80A

Operating temperature: 0–60°C

Voltage: 12 V

Input voltage

(charging port): 5 V

/1A

Output voltage

(output USB): 5 V

/1A/2A

Only for petrol motors with a

max. 2 litre engine and for

diesel motors with a max.

1.6 litre engine.

Technical and visual changes may be made in fur-

ther development without notifying the customer.

All dimensions, notices and speciﬁcations in the op-

erating instructions are therefore subject to change.

Legal claims arising from the operating instructions

are therefore not applicable.

Delivery Contents

1 Power pack with vehicle jump start aid

1 USB power cable

1 Jumper cable

1 Power supply adaptor

1 Set of operating instructions

General safety

instructions

This section covers the basic safety

instructions for when working with

the device.

Personal safety:

This device can be used by

children 8 years and older and

also by persons with reduced

physical, sensory or mental ca-

pacities or a lack of experience

and knowledge if they are

supervised or they have been in-

structed with regard to the safe

use of the device and they un-

derstand the dangers it presents.

Do not allow children to play

with the product. Cleaning and

user maintenance must not be

performed by children without

supervision.

Children must be supervised to

ensure that they do not play with

the device.

8 GB/IE/NI

General safety instructions / Set upGeneral safety instructions

Keep the device away from

people - especially children -

and pets.

In work areas the user is respon-

sible for third party damage

caused by the use of the device.

Keep the device in a dry loca-

tion and out of the reach of

children.

CAUTION: How to

avoid damage to the

device and any harm

to persons that may

result from such

damage:

Using the device:

Before setup, check the device

for damage and only use it in

perfect condition.

Do not expose the device to rain

or wet weather and do not al-

low it to come into contact with

water or to be submerged in

water. There is a risk of electric

shock!

Keep all openings on the device

clear during operation. Do not

close the openings with your

hands or ﬁngers, and do not

cover the device. There is a risk

of overheating!

Switch the device oﬀ and re-

move the plug from the cigarette

lighter plug socket:

- if the device is not in use;

- if you are leaving the device

unaccompanied;

- if carrying out maintenance or

cleaning it;

- if the connector cable is dam-

aged;

- if foreign objects enter the

device or you notice unusual

noises.

Only use accessories supplied

and recommended by the

manufacturer.

Do not dismantle or modify the

jump start aid. This device must

only be repaired by a mainte-

nance technician.

Do not use the device in areas

with a risk of explosion, e.g.

near ﬂammable liquids, gases or

powders.

Do not expose the device to

heat.

Do not store in places where the

temperature can exceed 70° C.

Only charge in an ambient tem-

perature of 0°C–60° C.

Only use the power supply

adapter

delivered with the

device.

9 GB/IE/NI

General safety instructions / Set upGeneral safety instructions

CAUTION: How to

avoid accidents and

injuries from electric

shock:

Electrical safety:

Do not carry the device by the

cable. Do not pull on the cable

to unplug it from the socket. Pro-

tect the cable from heat, oil and

sharp edges.

Only connect the connector

cable to the vehicle cigarette

lighter.

Observe your vehicle manufac-

turer’s instructions for the use of

the cigarette lighter.

If the cable is damaged, immedi-

ately unplug it from the cigarette

lighter.

Do not short-circuit the two

clamps. This can lead to danger-

ous situations!

Rechargeable batteries:

CAUTION! EXPLO-

SION HAZARD!

Do not short-circuit the

rechargeable battery and/or

open it. The battery may over-

heat, ignite or explode.

Do not expose the rechargeable

battery to high temperatures.

The battery can explode.

Regularly check the battery for

leakage. Leaking or damaged

batteries may cause burns to the

skin if touched; therefore, always

wear suitable safety gloves!

Carefully wipe up the liquid

with a cloth and avoid contact

with skin and eyes. If the liquid

should come into contact with

your skin or eyes, immediately

wash out with clean water and

seek medical attention.

Set up

Monitoring the capacity of the

jump start aid

To monitor the capacity of the jump start aid,

press the power button

. When charging,

the indicator lights

ﬂash. The number of

permanently lit indicator lights

shows the

battery power of the jump start aid. When the

device is fully charged, the indicator lights

will be permanently lit.

Indicator lights Battery power

Device 0 %

1 permanent 25 %

2 permanent 50 %

3 permanent 75 %

4 permanent 100 %

10 GB/IE/NI

Set up / FAQs / Troubleshooting / Cleaning / Storage Set up

Charging the jump start aid

Plug in the power pack with vehicle start-up

aid

Plug the power supply adaptor

cable into

the charging port (5 V

/1A)

of the

power pack with vehicle start-up aid.

Charging the 12 V

vehicle battery

Make sure that the charger

has no less

than 3 illuminated indicator lights

Function LEDs Meaning/Error Solution

1. Connect the

jumper cable

the jump start aid

to the car's start-

up aid output

of the charger

LED

on the jumper

cable

glows red contin-

uously

The voltage detected

in the charger is not

suﬃcient to charge

the car battery

Charge the charger.

LEDs

ﬂash red and

green

Charger ready Carry on to step 2

2. First connect the

red clamp A to the

positive pole of

the vehicle battery

and then connect

the black battery

clamp B to the

negative pole

(see picture 1).

LED

ﬂashes red, a short

warning signal sounds

The temperature is too

high, possibly due to

several jump start

attempts

Disconnect the

black battery clamp

ﬁrst and then the

red clamp from the

battery poles.

Start again from

step 1

LED

ﬂashes red, a con-

tinuous warning signal

sounds

Battery clamps A and

B are the wrong way

round.

It is caused by a short-

circuit or the battery is

leaking

LED

ﬂashes red once, a

continuous warning signal

sounds, followed by two

short warning beeps

The red

and green

LED

ﬂash alternately.

After 1–2 seconds only the

green LED

glows

The connection is

correct

Carry on to step 3

3. Starting up

the vehicle

2. 1.

As soon as the vehicle starts,

remove the jumper cable

from the jump

start aid within 30 seconds and disconnect

ﬁrstly the black battery clamp and then the red

clamp from the battery poles. Otherwise dan-

gerous situations can arise!

Leave the vehicle engine running.

Note: The button on the LED box

from the

jumper cable has no eﬀect and must not be

used. It is only used for troubleshooting pur-

poses during the manufacture of the device.

11 GB/IE/NI

Set up / FAQs / Troubleshooting / Cleaning / Storage Set up

Charging mobile phones

and tablets

Press the power switch

Connect your mobile phone or tablet’s USB

power cable to the USB output (5 V

/1A/2A)

and then to your mobile phone or tablet.

Note: Charging is not possible if the power

pack is already fully charged.

Switching on the lights

When switching on the lights, hold down the

power button

for 3 seconds.

Press the power button

again to switch on

strobe mode.

Press the power button

again to switch on

the SOS signal.

Press the power button

again to switch oﬀ

the light.

CAUTION! Do not look directly at the LED

lights as this can damage your eyes.

Note: It is not possible to turn on the light

while the power pack is charging.

FAQs

Q: How can I switch the device off?

A: The device automatically switches oﬀ after

20 seconds of none use.

Q: How long does it take to fully charge

a mobile phone with the device?

A: With a battery power of 2500 mAh: 1A

(2–3 hours) / 2A (1–2 hours)

Q: How often can a vehicle be started

with a fully loaded device?

A: approx. 20 times (engine capacity ≤ 2.0 l)

Q: How long does the device’s

battery last?

A: 3–6 months. However, we recommend

charging the battery every 1–2 months.

Troubleshooting

= Problem

= Cause

= Solution

The jump start aid is not fully

charged, although all 4 indicator

lights

are permanently lit.

It is 60% charged after a long period out of

use or in storage.

Disconnect the charger

and reconnect it.

The correct number of LEDs are glowing.

There is no response to pressing the

power button

The jump start aid’s low voltage protection is

activated.

Connect the charger

to the charging output

(5 V

/ 1A)

Cleaning

You must not splash the

device with water or place it in water.

There is a risk of injury due to electric

shock if moisture enters the device.

Do not use cleaners or solvents. These could

damage the equipment beyond repair.

Keep the casing of the device clean.

Use a damp cloth or brush to clean.

Storage

Keep the device in a dry location and out of

the reach of children.

12 GB/IE/NI

... / Environmental notes and disposal information / EC Declaration of Conformity Warranty and service information

Warranty and service

information

Creative Marketing

Consulting GmbH warranty

Dear customer,

the warranty for this equipment is 3 years from the

date of purchase. In the event of product defects,

you have legal rights against the retailer of this

product. Our warranty, outlined below, does not

limit your statutory rights.

Warranty terms

The warranty period begins on the date of pur-

chase. Please retain the original sales receipt. This

document will be required as proof of purchase.

Should this product have a material or manufactur-

ing error within three years of the purchase date,

the product will be repaired or replaced - depend-

ent on our choice - by us at no cost to you. This

warranty service requires that you retain proof of

purchase (sales receipt) for the defective device for

the three year period and that you brieﬂy explain

in writing what the fault entails and when it occurred.

If the defect is covered by our warranty, we will re-

turn the repaired device or a replacement thereof.

A repair or exchange of the device does not ex-

tend a new warranty period.

Extent of warranty

The device has been manufactured according to

strict quality guidelines and meticulously examined

before delivery.

The warranty applies to defects in material or man-

ufacture. This warranty does not extend to product

parts, which are subject to normal wear and tear

and can thus be regarded as consumable parts, or

for damages to fragile parts, e.g. switches, re-

chargeable batteries or parts made from glass.

This warranty is void if the product is damaged,

improperly used, or serviced. For proper use of the

product, all of the instructions given in the operat-

ing instructions must be followed precisely. Uses

and acts that the operating instructions dissuade or

warn against are to be avoided without question.

The product is only intended for private use and is

not for commercial use. The warranty becomes

void, in the event of misuse and improper use, use

of force, and any interference not carried out by

our authorised service branch.

Processing of warranty claims

Please follow the instructions below to ensure quick

processing of your claim:

Please retain proof of purchase and the article

number (e.g., EAN) for all inquiries.

The product number can be found on the type

plate, an engraving, the cover page of your instruc-

tions (bottom left) or the sticker on the back or

bottom.

Should you have any functional fault or other error,

ﬁrst contact the service department listed below by

phone or email.

You can then forward a product recognised as de-

fective with a proof of purchase (sales receipt) and

a statement indicating what the fault entails and

when it occurred to the service address, which will

be given at no cost to you for postage.

Note:

You can download this handbook and

many more, as well as product videos

and software at www.lidl-service.com.

How to contact us:

GB, IE, NI

Name: C. M. C. GmbH

Internet address: www.cmc-creative.de

E-mail: service.gb@cmc-creative.de

Phone: 0-808-189-0652 (standard

rates for German landlines)

Registered oﬃce: Germany

13 GB/IE/NI

... / Environmental notes and disposal information / EC Declaration of Conformity Warranty and service information

IAN 279357

Please note that the following address is not a ser-

vice address.

Please ﬁrst contact the service point (hotline)

named above.

Address:

C. M. C. GmbH

Katharina-Loth-Str. 15

DE-66386 St. Ingbert

GERMANY

Environmental notes and

disposal information

Don’t waste, recycle!

Always recycle the tool, accessories and

packaging in an environmentally-friendly

manner.

Do not dispose of the product in household waste,

in ﬁre or in water. Whenever possible, devices,

which are no longer functional, should be recycled.

Ask your local distributor for help.

As a consumer, you are legally required

(Battery Directive) to return all used bat-

teries. Batteries containing harmful sub-

stances are labelled with the adjacent

symbol, which indicates the ban on dis-

posal in household waste. The abbrevia-

tions for the essential heavy metals are:

Cd = Cadmium, Hg = Mercury,

Pb = Lead.

Take used batteries to a disposal facility in your

city or community or back to the distributor. This

satisﬁes your legal obligations and you are greatly

contributing to protecting the environment.

EC Declaration of

Conformity

We,

C. M. C. GmbH

Documentation oﬃcer: Andre Scheer

Katharina-Loth-Str. 15

DE-66386 St. Ingbert

GERMANY

declare under our sole responsibility that the product

Portable jump starter with

power bank UPBS 8000 A1

Year of manufacture: 2016 / 43

EAN: 279357

Year of CE mark: 2016

Model: PORTABLE JUMP STARTER WITH

POWER BANK UPBS 8000 A1

meets the basic safety requirements of

European Directives

2014/30/EU

2014/35/EU

2011/65/EU

2009/125/EU

and their amendments.

The object of the declaration described above

meets the requirements of Directive 2011 / 65 / EU

of the European Parliament and Council dated 8th

June 2011, restricting the use of certain hazardous

substances in electrical appliances and electronics.

The conformity assessment is based on the

following harmonised standards:

EN 55032:2015

EN 55024:2010+A1:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50498:2010

EN 62321-1:2013 / EN 62321-2:2014 /

EN 62321-3-1:2014

14 GB/IE/NI

EC Declaration of Conformity

EN 62321-4:2014 / EN 62321-5:2014 /

EN 62321-6:2015

EN 62321:2009

EN 60335-1:2012+A11:2014

EN 62233:2008

EN 60950-1:2006+A11:2009+A1:2010+A

12:2011+A2:2013

EN 61558-2-16:2009+A1:2013

EN 61558-1+A1:2009

EU 1194/2012

St. Ingbert, 06.10.2016

p.p. Andre Scheer

- Quality Control Manager -

Inhaltsverzeichnis

Page is loading ...

C. M. C. GmbH

Katharina-Loth-Str . 15

DE-66386 St. Ingbert

GERMANY

Last Information Update · Stand der

Informationen: 10 / 2016 · Ident.-No.:

UPBS8000A1102016-GB/IE/NI

IAN 279357

ULTIMATE SPEED UPBS 8000 A1 Operating instructions

Brand: ULTIMATE SPEED

Model: UPBS 8000 A1

Category: Battery chargers

Type: Operating instructions

Download PDF

report

in other languages

Deutsch: ULTIMATE SPEED UPBS 8000 A1 Bedienungsanleitung

ULTIMATE SPEED UPBS 8000 A1 Operating instructions

ULTIMATE SPEED UPBS 8000 A1 Operating instructions

in other languages

Related papers

Other documents