2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Racks
  6. Rack accessories
  7. Kolpin
  8. 20200
20200

Kolpin 20200 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Kolpin 20200 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of the Kolpin 20200?
    What components are included in the Kolpin 20200?
    How do I assemble the Kolpin 20200?
    Where can I find additional installation options for the Kolpin 20200?
Rev. 00
20200 UNIVERSAL GUN BOOT BRACKET
NO.
P/N
Description
QTY.
1
U-Bracket 2
2
70321
Rubber Coated Ring 1
3 1/2" Nylock Nut 1
4 1/2” Flat Washer 2
5
Rotating Plate 1
6
70200
Mounting Plate 1
7
79446
Angle Plate 1
8 * 1/4" Nylock Nut 6
9 * 3/8” Nylock Nut 2
10 * 5/16” Nylock Nut 10
11 * 1/4" Flat Washer 6
Bracket Assembly Instructions:
1.
a. Attach angle plate to mounting plate using 5/16” x 3/4” hex head bolts, 5/16” washers and 5/16
nylock nuts.
b. Attach assembly to a cross support tube of ATV rack using 1/4" x 1” wide u-bolts, 1/4" washers
and 1/4" nylock nuts.
c. Attach assembly to outer tube of ATV rack using 1/4" x 1 1/4” wide u-bolts, 1/4" washers and
1/4" nylock nuts.
NO.
P/N
Description
QTY.
12 * 3/8” Flat Washer 2
13 * 5/16” Flat Washer 16
14 * 5/16” x 1” Hex Head Bolt 4
15 * 5/16” x 3/4” Hex Head Bolt 2
16 66352 Locking Pin 1
17 * 1/4" x 1 1/4" SQ U-Bolt 2
18 * 5/16” x 1 3/4" SQ U-Bolt 2
19 * 1/4" x 1” Round U-Bolt 1
20 * 1/4" x 1 1/4" Round U-Bolt 2
21 * 5/16” x 2” Round U-Bolt 2
22 * Rubber Caps 6
23
79447
Hardware Pack* 1
FRONT OF ATV
LEFT SIDE SETUP
RIGHT SIDE SETUP
ATV RACK
CROSS SUPPORT TUBE
7
19
20
2
8
11
8
11
ATV RACK
OUTER TUBE
6
Rev. 00
2.
a. Determine orientation of rotating plate, plate may be flipped around to accommodate either
side of the ATV
b. Attach rubber coated ring to rotating plate using 1/2" washers and 1/2" nylock nut.
c. Attach u-bracket to rotating plate using 3/8” washers and 3/8” nylock nuts. These will need to
be positioned correctly to properly secure gun boot.
d. Attach rotating plate to mounting plate using 5/16” x 1” hex head bolts, 5/16” washers and
5/16” nylock nuts.
e. To secure gun boot use 5/16” x 1” bolts, 5/16” washer and 5/16” nylock nuts OR locking pin
provided.
FRONT OF ATV
14
5
9
12
2
10
13
13
15
1
4
3
10
13
6
U-BRACKET ONLY NEEDED
FOR GUN BOOT 4.3
Rev. 00
Additional Installation Options:
Kolpin Outdoors, Inc.
205 N. Depot Street, Fox Lake, WI 53933
Phone #: (877) 9KOLPIN or (920) 928-3118
www.kolpin.com customerservice@kolpin.com
ATV RACK EXTENDER
*SHOWN ON POLARIS
UTV FRAME UP TO 2” OD
/