Domo DO926BFK Owner's manual

PRODUCT OF

DO926BFK

Handleiding Koelkast, diepvriezer

Mode d’emploi Réfridgérateur, congélateur

Gebrauchsanleitung Kühlschrank, gefrierschrank

Instruction booklet Refrigerator, freezer

Manual de instrucciones Frigoríco, congelador

Návod k použití Lednice, Kompaktní mrazák

Návod na použitie Chladnička, Mraznička

Lees aandachtig alle instructies - bewaar deze handleiding voor latere raadpleging.

Lisez attentivement les instructions - gardez le mode d’emploi pour utilisation ultérieur.

Lesen Sie genau die Anweisungen - bewahren Sie die Gebrauchsanleitung für spätere

heranziehung.

Read all instructions carefully - save this instruction manual for future reference.

Lea detenidamente todas las instrucciones - Conserve este manual para futura referencia.

Před použitím si důkladně přečtěte tento manuál - manuál si uschovejte i pro případ

budoucího nahlédnutí.

Pred použitím si dôkladne prečítajte tento manuál - manuál si uschovajte aj pre prípad

budúceho nahliadnutie.

NL Nederlands 3

FR Français 15

DE Deutsch 27

EN English 39

ES Espagnol 51

CZ Čeština 63

SK Slovenčina 75

Page is loading ...

10

DO926BFK

NL

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

2. Aan de onderkant van de deur zit een deurstop en een teonbus ter geleiding van het

scharnier. Verplaats deze naar de andere kant.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Verwijder de middelste bouten, scharnier en afdekstopjes. Plaats deze aan de andere

zijde. Til de deur op en plaats deze op een zacht oppervlak om krassen te vermijden.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

4. Aan de bovenkant van de deur zit een teonbus ter geleiding van het scharnier en een

afdekstopje. Verplaats deze naar de andere kant.

Aan de onderkant van de deur zit een deurstop en een teonbus ter geleiding van het

scharnier. Verplaats deze naar de andere kant.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

5. Verwijder de onderste bouten, scharnier en het stelvoetje onderaan het apparaat.

Verwijder het stelvoetje van de andere kant van de bodem en breng het naar de

overeenkomstige positie aan de tegenovergestelde kant van de bodem

11

DO926BFK

www.domo-elektro.be

NL

6. Maak de bouten, scharnierbeugel en het stelvoetje aan de andere kant van de bodem

vast.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

7. Zet de onderste deur voorzichtig op zijn plaats. Zorg dat de deur zowel horizontaal als

verticaal is uitgelijnd zodat de afdichtingen op alle zijden gesloten zijn voordat u het

middelste scharnier volledig vastmaakt. Breng het scharnier terug en schroef vast.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

8. Plaats de bovenste deur. Plaats de scharnieren van de bovenste deur, schroef deze vast

en plaats het afdekplaatje terug.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

9. Met de deur gesloten, controleer of de deur zowel horizontaal als verticaal is uitgelijnd

en de afdichtingen op alle zijden gesloten zijn voordat u het bovenste scharnier volledig

vastmaakt. Indien nodig, stel de stelvoetjes af.

Page is loading ...

22

DO926BFK

FR

outils ne sont pas fournis).

1. Enlevez la cache de protection des vis. Enlevez les vis ainsi que la charnière supérieure

qui maintient la porte en place. Soulevez la porte et posez-la sur une surface douce, an

d’éviter de la grier.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

2. Sur la partie inférieure de la porte se trouvent un arrêt de porte et une bague en téon

qui guide la charnière. Déplacez-les de l’autre côté.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Retirez les boulons, la charnière et les bouchons de protection centraux. Placez-les de

l’autre côté. Soulevez la porte et posez-la sur une surface douce, an d’éviter de la grier.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

4. Sur la partie supérieure de la porte se trouvent une bague en téon qui guide la charnière

et un bouchon de protection. Déplacez-les de l’autre côté.

Sur la partie inférieure de la porte se trouvent un arrêt de porte et une bague en téon

qui guide la charnière. Déplacez-les de l’autre côté.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

23

DO926BFK

www.domo-elektro.be

FR

5. Enlevez la charnière et les boulons et inférieurs, ainsi que le pied réglable situé sous

l’appareil.

Enlevez le pied réglable situé de l’autre côté, sous l’appareil, et déplacez-le vers la

position correspondante sur le côté opposé, sous l’appareil.

6. Fixez les boulons, la charnière-étrier et le pied réglable de l’autre côté, sous l’appareil.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

7. Replacez prudemment la porte inférieure. Veillez à ce que la porte soit bien ajustée,

tant horizontalement que verticalement, de manière à ce que les joints d’étanchéité

se referment sur tous les côtés, avant de revisser dénitivement la charnière centrale.

Replacez la charnière et vissez-la.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

8. Placez la porte supérieure. Placez les charnières de la porte supérieure, vissez-les et

replacez le cache de protection.

Page is loading ...

34

DO926BFK

DE

wurde und dass das Gerät leer ist. Es empehlt sich, einen Kreuzschlitzschraubendreher und

einen Maulschlüssel zu verwenden (beide nicht im Lieferumfang enthalten).

1. Entfernen Sie die Abdeckung der Schrauben. Entfernen Sie die Schrauben und

anschließend das obere Scharnier, dass die Tür in ihrer Position hält. Heben Sie die Tür

hoch und legen Sie diese zur Vermeidung von Kratzern auf einen weichen Untergrund.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

2. An der Unterseite der Tür bendet sich ein Stopper und eine Teonschiene als Führung

des Scharniers. Versetzen Sie diese auf die andere Seite.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Entfernen Sie die mittleren Bolzen, das Scharnier und die Abdeckungen. Setzen Sie diese

an der anderen Seite ein. Heben Sie die Tür hoch und legen Sie diese zur Vermeidung von

Kratzern auf einen weichen Untergrund.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

4. An der Oberseite der Tür bendet sich eine Teonschiene zur Führung des Scharniers und

eine Abdeckung. Versetzen Sie diese auf die andere Seite.

An der Unterseite der Tür bendet sich ein Stopper und eine Teonschiene als Führung

des Scharniers. Versetzen Sie diese auf die andere Seite.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

35

DO926BFK

www.domo-elektro.be

DE

5. Entfernen Sie die untersten Bolzen, das Scharnier und den Stellfuß unten am Gerät.

Entfernen Sie den Stellfuß der anderen Seite vom Boden und setzen Sie ihn an der

entsprechenden Position an der gegenüberliegenden Seite am Boden wieder ein.

6. Befestigen Sie die Bolzen, den Scharnierbügel und den Stellfuß an der

gegenüberliegenden Seite des Bodens.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

7. Setzen Sie die untere Tür vorsichtig ein. Achten Sie darauf, dass die Tür sowohl senkrecht

als auch waagerecht ausgerichtet ist, sodass die Dichtungen an allen Seiten anliegen,

bevor Sie das mittlere Scharnier vollständig festziehen. Setzen Sie das Scharnier wieder

ein und schrauben Sie es fest.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

8. Setzen Sie die oberste Tür ein. Setzen Sie die Scharniere der obersten Tür ein, schrauben

Sie diese fest und befestigen Sie die Abdeckung erneut.

Page is loading ...

39

DO926BFK

www.domo-elektro.be

EN

WARRANTY

Dear client ,

All of our products are always submitted to a strict quality control before they are sold to you.

Should you nevertheless experience problems with your device, we sincerely regret this.

In that case, we kindly request you to contact our customer service.

Our sta will gladly assist you.

+32 14 21 71 91 [email protected]

Monday – Thursday: 8.30 – 12.00 and 13.00 – 17.00

Friday: 8.30 – 12.00 and 13.00 – 16.30

This appliance has a two year warranty period. During this period the manufacturer is

responsible for any failures that are the direct result of construction failure. When these

failures occur the appliance will be repaired or replaced if necessary. The warranty will not be

valid when the damage to the appliance is caused by wrong use, not following the instructions

or repairs executed by a third party. The guarantee is issued with the original till receipt. All

parts, which are subject to wear, are excluded from the warranty.

If your device breaks down within the 2-year warranty period, you can return the device

together with your receipt to the shop where you purchased it.

The guarantee on accessories and components that are liable to wear-and-tear is only 6

months.

The guarantee and responsibility of the supplier and manufacturer lapse automatically in the

following cases:

· If the instructions in this manual have not been followed.

· In case of incorrect connection, e.g., electrical voltage that is too high.

· In case of incorrect, rough or abnormal use.

· In case of insucient or incorrect maintenance.

· In case of repairs or alterations to the device by the consumer or non-authorised third

parties.

· If the customer used parts or accessories that are not recommended or provided by the

supplier / manufacturer.

40

DO926BFK

EN

SAFETY INSTRUCTIONS

- This appliance must be grounded. In the event of an electrical short circuit, grounding

reduces the risk of electrical shock by providing an escape wire for the electrical current

- Do not use an extension cord

- Use an exclusive wall outlet. Do not connect your refrigerator to extension cords or together

with any other appliance in the same wall outlet. Do not splice the cord.

- An empty refrigerator is a very dangerous attraction to children. Remove either the gasket,

latches, lids or doors from unused appliances, or take some other action that will guarantee it

harmless.

- Do not damage the refrigerant circuit.

- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or

a similarly qualied person in order to avoid a hazard.

- Risk of child entrapment. Before you throw away your old refrigerator or freezer.

Take o the doors

Leave the shelves in place so that children may not easily climb inside.

This appliance can be used by children, starting from the age of 8 and up. And by persons with

a physical or sensorly limitation as well as, mentally limited persons or persons with a lack of

experience and knowledge. On the condition that these persons have received the necessary

instruction on how to use this appliance in a safe way and they must also know the dangers

that can occur in using this appliance.

Children cannot be allowed to play with the appliance.

Maintenance and cleaning of the appliance, cannot be done by children younger than 8 year

old.

This appliance is suitable to be in an household environment and in similar surroundings such

as :

Kitchen for personnel of shops, oces or other similar professional surrounding.

Farms

Hotel or motel rooms and other surroundings with a residential character

Guest rooms or similar

Attention : This appliance can not be used with external timer or separate remote control.

41

DO926BFK

www.domo-elektro.be

EN

PARTS

1. Temperature control knob

2. Shelves

3. Cover for vegetable container

4. Vegetable container

5. Freezer drawers

6. Levelling feet

7. Door shelves

8. Door bottle shelf

INSTALLATION

· Remove the exterior and interior packing, wipe the outside thoroughly with a soft dry cloth

and the inside with a wet, lukewarm cloth. Avoid placing the cabinet in a narrow recess

or near any leave source, direct sunlight, or moisture. Let air circulate freely around the

cabinet. Keep the rear of the refrigerator 127mm away from the wall.

· Location

· Select a place with a strong, level oor.

· Allow 5 cm of space between the back of the refrigerator and any adjacent wall.

· Avoid direct sunlight and heat. Direct sunlight may aect the acrylic coating. Heat sources

nearby will cause higher electricity consumption.

· Avoid very moist places. Too much moisture in the air will cause frost to from very quickly

on the evaporator, and your refrigerator.

· Before connecting your refrigerator to the power supply, check that the voltage stated

on the rating label of your appliance corresponds to the voltage in your home. A dierent

voltage could damage the appliance.

· The appliance must be grounded. The manufacturer is not responsible for damages that

may occur as a result of usage without grounding.

· For uneven surfaces, front feet can be aligned.

· After installation, leave the freezer for 3 hours before turning it on. This way the refrigerant

can settle.

· Allow the appliance to run empty for 24 hours so the compartment can cool to the

1

2

3

4

5

6

7

8

42

DO926BFK

EN

appropriate temperature.

· This appliance is designed to operate in ambient temperature between 16°C and 38°C.

If these temperatures are exceeded, i.e. colder or warmer, the appliance will not operate

correctly.

USE

TEMPERATURE CONTROL

The fridge is controlled with a temperature control knob located inside the appliance.

Adjust the control knob as desired to suit your individual preference.

· MIN is warmest setting

· MED is normal setting

· MAX is coldest setting

· The running time and temperature are aected by where the fridge is located, how often

the door is opened and the temperature of the room the fridge is located in.

· When you use the appliance for the rst time or after defrosting, adjust the control knob

to the coldest setting for at least 2 hours before introducing food to be stored, and then

readjust to the middle setting.

MOVING YOUR APPLIANCE

If the appliance is turned o for any reason, wait for 10 minutes before turning it back on. This

will allow the refrigeration system pressures to equalise before restarting.

· Turn o the appliance and unplug it from the mains socket. Remove all food. Also remove

all mobile parts (shelves, accessories, etc.) or x them into the fridge to avoid any shock.

· Relocate and install. If the appliance has been left on its side for any length of time, leave it

standing upright for at least 10 minutes before turning on.

Your appliance uses isobutane (R600a) as a refrigerant. Although R600a is an environmentally

friendly and natural gas, it is explosive. Therefore you should be careful during shipment and

installation to prevent your appliance’s cooler elements from being damaged. In the event of

a leak caused by damage to the cooler elements, move your fridge from open ame or heat

sources and ventilate the room where the appliance is located for a few minutes.

STORING FOOD IN THE FRIDGE

The fridge helps to extend the storage times of fresh perishable foods.

Fresh food care for best results:

· Store foods that are very fresh and of good quality.

· Ensure that food is well wrapped or covered before it is stored. This will prevent food from

43

DO926BFK

www.domo-elektro.be

EN

dehydrating, deteriorating in colour or losing taste and will help maintain freshness. It will

also prevent odour transfer.

· Make sure that strong smelling foods are wrapped or covered and stored away from foods

such as butter, milk and cream which can be tainted by strong odours.

· Cool hot foods down before placing them in the fridge.

FREEZING AND STORING FOOD IN THE FREEZER

Use the freezer

· To store deep-frozen food.

· To make ice cubes.

· To freeze food.

Note: Ensure that the freezer door has been closed properly.

Avoid opening the freezer drawers unnecessarily.

Purchasing frozen food

· Packaging must not be damaged.

· Use by the ‘use by /best before/best by/’ date.

· If possible, transport deep-frozen food in an insulated bag and place quickly in the freezer.

Freezing fresh food

Freeze fresh and undamaged food only. To retain the best possible nutritional value, avour

and colour, vegetables should be blanched before freezing.

Aubergines, peppers, zucchini and asparagus do not require blanching.

Note: Keep food to be frozen away from food which is already frozen.

· The following foods are suitable for freezing: Cakes and pastries, sh and seafood, meat,

game, poultry, vegetables, fruit, herbs, eggs without shells, dairy products such as cheese

and butter, ready meals and leftovers such as soups, stews, cooked meat and sh, potato

dishes, soués and desserts.

· The following foods are not suitable for freezing:Types of vegetables, which are usually

consumed raw, such as lettuce or radishes, eggs in shells, grapes, whole apples, pears and

peaches, hard-boiled eggs, yoghurt, soured milk, sour cream, and mayonnaise.

Packing frozen food

To prevent food from losing its avour or drying out, place food in airtight packaging.

1. Place food in packaging.

2. Remove air.

3. Seal the wrapping.

4. Label packaging with contents and dates of freezing.

44

DO926BFK

EN

Suitable packaging:

Plastic lm, tubular lm made of polyethylene, aluminium foil, freezer containers.

Recommended storage times of frozen food in the freezer

These times vary depending on the type of food. The food that you freeze can be preserved

from 1 to 12 months (minimum at -18°C).

Food Storage time

Bacon, casseroles, milk 1 month

Bread, ice cream, sausages, pies, prepared shellsh, oily sh 2 months

Non-oily sh, shellsh, pizza, scones and muns 3 months

Ham, cakes, biscuits, beef and lamb chops, poultry pieces 4 months

Butter, vegetables (blanched), eggs whole and yolks, cooked cray-

sh, minced meat (raw), pork (raw)

6 months

Fruit (dry or in syrup), egg whites, beef (raw), whole chicken, lamb

(raw), fruit cakes

12 months

Never forget:

· When you freeze fresh foods whit a ‘use by /best before/best by/’ date, you must freeze

them before the expiry of this date.

· Check that the food was not already frozen. Indeed, frozen food that has thawed

completely must not be refrozen.

· Once defrosted, food should be consumed quickly.

POWER FAILURE

Most power failures are corrected within an hour or two and will not aect your refrigerator

temperatures. However, you should minimize the number of door openings while the power

is o. During power failures of longer duration, take steps to protect your food by blacking dry

ice on top of packages.

Frozen food should not be aected if the power failure lasts for less than 15 hours.

Do not refreeze frozen foods that have thawed completely. The food may be dangerous to

eat.

IMPORTANT RULES

· Never place hot foods in the appliance

· Beverages should be stored in sealed containers.

· Foods to be stored for a long time should be wrapped in cellophance or polyethylence, or

kept in glass containers.

· Never place spoiled foods in the cabinet.

45

DO926BFK

www.domo-elektro.be

EN

· Don’t overload the cabinet.

· Caution: please keep the products away from the re or similar glowing substance before

you dispose the refrigerator.

· Caution : Not for outer camping use (ex. Tent)

· Caution: For indoor use only.

· Caution: The appliance can not be used in public transportation.

· Do not freeze food again after it has been defrosted already.

· Do not place carbonated liquids such as zzy drinks into the freezer.

· Be careful when consuming ice lollies straight from the freezer to avoid freeze burns.

· Do not take anything out of the freezer with wet hands.

· The freezer produces sounds when the compressor pumps the refrigerant around. This is

normal.

· Make sure that all food in the freezer is covered.

· Do not press together the food. The air should be able to circulate around the food.

· Do not leave the door open for too long. Also make sure that the door is always properly

closed.

· Label the food with the date to be able to check the expiration in the freezer.

DOOR CONVERSION

1. Remove the cover plate of the screws. Remove the three screws and then the upper

hinge that holds the door in place. Lift the door o and place it on a soft surface to

prevent scratching.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

2. On the bottom of the door there is a door stop and a Teon bush to guide the hinge.

Move this to the other side.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

3. Remove the metal screws, hinge and cover plugs. Place them on the other side. Lift the

46

DO926BFK

EN

door o and place it on a soft surface to prevent scratching.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

4. On the top of the door, there is a Teon bush to guide the hinge and a cover plug. Move

this to the other side.

On the bottom of the door there is a door stop and a Teon bush to guide the hinge.

Move this to the other side.

3. Take off the middle hinge by removing

the screws. Lift the lower door and place

it on a padded surface to prevent it from

scratching.

Remove the screws’ covers and place

them to the opposite side.

Swap the position of the plastic tube and

hole cover on top of the lower door.

Remove the door block, screw and plastic

tube under the lower door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

unscrew

Reversing the Door Swing

Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner

1. Take off the hinge cover.

2. Remove the the upper hinge. Lift the

upper door and place it on a padded

surface to prevent it from scratching.

Remove the door block, screw and plastic

tube under the upper door and move

them to the opposite side. You may

need to replace the door block to fit the

opposite side.

• Ensure the unit is unplugged and empty.

• All parts removed must be saved to do the reinstallation of the door.

• Do not lay the unit flat as this may damage the coolant system.

• We recommend that 2 people handle the unit during assembly.

• If you want to have the door swing reversed, we recommend that you contact a

qualified technician. You should only try to reverse the door yourself if you believe

that you are qualified to do so.

8

INSTALLATION

LFC60W16_IB_160201_grace.indd 8 1/2/16 10:43 am

5. Remove the lower screws, hinge and the adjustable foot from the base of the appliance.

Remove the adjustable foot from the other side of the base and move it to the same

position on the opposite side of the base.

6. Fasten the screws, hinge bracket and the adjustable foot to the other side of the base.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

7. Carefully replace the bottom part of the door into position. Make sure that the door is

aligned horizontally as well as vertically so that the seal is closed on all sides before you

tighten the centre hinge completely. Return the hinge to its positions and fasten it.

47

DO926BFK

www.domo-elektro.be

EN

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

8. Position the upper door. Position the hinge of the upper door, fasten it with the screw and

replace the cover plate.

5. Reverse the middle hinge. Screw the

middle hinge onto the opposite side of

the unit.

6. Carefully set the upper door back into

place, inserting in onto the middle hinge.

7. Insert the upper hinge and screw it

tightly to the top of the unit.

Middle hinge

Ensure the lower door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

Ensure the upper door is aligned

horizontally and vertically, so that

the seals are closed on all sides

before finally tightening the hinge.

4. Remove the lower screws and lower

hinge from the unit bottom. Reverse the

lower hinge, move and secure it with

the lower screws to the opposite side of

the unit bottom. Carefully set the lower

door back into place, inserting it onto the

lower hinge.

8. Put the hinge cover back.

9

INSTALLATION

LFC60W16_IB_160201_grace.indd 9 1/2/16 10:43 am

9. With the door closed, check whether the door is aligned horizontally as well as vertically

and that the seal closes on all sides before you tighten the upper hinge completely. If

necessary, adjust the adjustable feet.

CLEANING AND MAINTENANCE

Do not use abrasive cleaning agents or solvents.

1. Disconnect the mains plug from the mains socket.

2. Take out the food and store in a cool location.

3. Clean the appliance with a soft cloth, warm water and detergent.

4. Wipe the door seal with clear water only and then wipe dry thoroughly.

5. After cleaning reconnect and adjust the temperature control knob as desired.

6. Put the food back into the appliance.

DEFROSTING

The refrigerator defrosts fully automatically.

While the cooling is running, beads of condensation or hoarfrost form at the back of the

refrigerator. This is normal. It is not necessary to wipe o the condensation or frost. The rear

panel defrosts automatically. The condensation runs into the condensation channel and is

conveyed to the cooling from where it evaporates.

Note: Keep the condensation channel and drainage hole clean, so that the condensation can

run out.

48

DO926BFK

EN

A layer of frost in the freezer will impair refrigeration of the frozen food and increases power

consumption. Remove the layer of frost regularly. Do not scrape o frost or ice with a knife or

pointed object. Doing this may damage the refrigerant tubes.

1. Remove the frozen food and place temporarily in a cool location.

2. Disconnect the appliance from the mains socket.

3. To accelerate the defrosting process, place a pan of hot water on a stand in the freezer.

4. Wipe up condensation with a cloth or sponge.

5. Wipe dry the freezer compartment.

6. Plug in the appliance and adjust the temperature control knob as desired.

7. Put the frozen food back in the freezer.

TROUBLE SHOOTING

Frequently, a problem is minor and a service call may not be necessary, use this trouble

shooting guide for a possible solution.

Does not work

· Check connection of power cord to power source.

· Plug in unit

· Use proper voltage.

Cools too frequently

· Check temperature setting and adjust as needed.

· Close door securely.

· Be sure that food is cool before inserting.

· Do not keep door open for too long and MINIMIZE door openings.

· Do not place unit close to heat sources Or direct sunlight.

Intemal temperature not cold enough

· Check connection of power cord to Power source.

· Plug in unit

· Check setting and adjust as needed.

· Close door securely.

· Be sure that food is cool before inserting.

· Do not keep door open for too long and MINMIZE, door openings.

· Allow room for airto circulate around unit..

· Use proper voltage.

49

DO926BFK

www.domo-elektro.be

EN

· Do not place unit close to heat sources or direct sunlight.

Freezer is not cold enough

· Check setting and adjust as needed

· Close door securely.

· Be sure that food is cool before inserting.

· Do not keep door open for too long.

· Use proper voltage.

50

DO926BFK

EN

ENVIRONMENTAL GUIDELINES

This symbol on the product or on its packaging indicates

that this product may not be treated as household waste.

Instead it must be brought to the applicable collection point

for recycling of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more

detailed information about recycling of this product, please

contact your local city oce, your household waste disposal

service or the shop where you purchased the product.

The packaging is recyclable. Please treat the packaging

ecologically.

Page is loading ...

Domo DO926BFK Owner's manual

This manual is also suitable for

Domo DO926BFK Owner's manual

in other languages

Related papers

Other documents