Britax Advocate ClickTight User guide

Brand: Britax

Model: Advocate ClickTight

Category: Car seat

Type: User guide

Tel.: 1-888-427-4829

Tel.: 1-704-409-1699

www.Britax.com

Britax Child Safety, Inc.

4140 Pleasant Road

Fort Mill, SC 29708 USA

A Britax Childcare company

ADVOCATE

CLICKTIGHT

™

User Guide

Guia del usuario

ADVOCATE

, BRITAX

, CLICK & SAFE

, CLICKTIGHT

™

, and EZ-Buckle

™

are

trademarks owned by Britax Child Safety, Inc., and registered in the U.S.A. and

and its components are subject to change without notice. Printed in USA.

P02088800 _A:08.14

Table of Contents

User Guide - English �� 1

Child Seat Features �� 2

Safety Information �� 4

Warnings .................................................................. 4

Important Notes ....................................................... 5

Registration .............................................................. 5

Certiﬁcation .............................................................. 6

Child Fit Information ................................................ 7

Rear-Facing Installation �� 8

Lap-Shoulder Belt Installation ................................. 8

Lower Anchor Installation ...................................... 10

Lap Belt Installation ............................................... 12

Forward-Facing Installation �� 14

Lap-Shoulder Belt Installation ............................... 14

Lower Anchor Installation ...................................... 16

Lap Belt Installation ............................................... 18

Securing Your Child �� 20

Child Seat Functions ��22

Click & Safe

Snug Harness Indicator ................... 22

Adjusting the Harness Height ................................ 23

Harness Buckle Position ........................................ 24

Using the Harness Buckle ..................................... 24

Using the Chest Clip ............................................. 24

Comfort Pillow ....................................................... 25

Seat Positions ........................................................ 25

Using the Lower Anchors and Tethers for Children

(LATCH) .................................................................. 27

Lower Connectors.................................................. 27

Impact Absorbing Tether ....................................... 28

Vehicle Compatibility��31

Vehicle Seating Positions ....................................... 31

Incompatible Vehicle Seat Belts ............................ 32

Maintenance �� 33

Cover ..................................................................... 33

Harness Buckle ...................................................... 37

Impact Absorbing Chest Pads ............................... 39

Cleaning �� 42

Troubleshooting �� 43

Warranty �� 44

User Guide - English

2 3

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Description

1. Cover

2. Harness Height Adjuster

3. Head Restraint

4. Seated Shoulder Height Label

5. Comfort Pads

6. Comfort Pillow

7. Forward-Facing Belt Slot / Harness Holder

8. Lower Connector Strap (LATCH component)

9. Lower Connector Adjuster Release Button (LATCH

component)

10. Lower Connector Adjuster (LATCH component)

11. Lower Connector (LATCH component)

12. User Guide Storage (in pocket behind cover)

13. Impact Absorbing Chest Pads

14. Chest Clip

15. Harness Buckle

16. EZ-Buckle™ Belly Pad

17. Harness Adjuster Button (red)

18. CLICKTIGHT Dial

19. Serial Number & Manufactured Date Label (under seat

cover)

20. CLICKTIGHT Mechanism

21. Click & Safe Snug Harness Indicator (under cover)

22. Harness Adjuster Strap

23. Recline Adjustment Handle

24. Side Impact Cushions

25. Shell

26. Rear-Facing Belt Slot

27. Recline Indicator

28. Impact Absorbing Tether (Top Anchorage Strap - LATCH

component) - stored in Tether Storage Compartment

29. Impact Absorbing Base

30. Tether Connector Strap (stored in Tether Storage

Compartment)

31. Tether Storage Compartment

32. Harness Yoke

33. Harness Straps

34. Lower Connector Storage

Child Seat Features

Front

Rear

4 5

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Safety Information

Failure to follow all warnings and instructions could result

in SERIOUS INJURY or DEATH.

FIT REQUIREMENTS

• Use only in a rear-facing position when using it with

an infant weighing less than 20 lbs (9.1 kg).

• Use only with children who weigh between 5 and 65

lbs (2.3 and 29.4 kg) and whose height is 49 in. (124.5

cm) or less. Use rear-facing for children who weigh

between 5 and 40 lbs (2.3 and 18 kg). Use forward-

facing for children who weigh between 20 and 65 lbs

(9.1 and 29.4 kg).

• Snugly adjust the belts provided with this child

restraint around your child.

INSTALLATION

• Secure the top anchorage strap provided with this

child restraint.

• Secure this child restraint with the vehicle’s child

restraint anchorage system if available, or with a

vehicle belt.

• Use the buckle slot closest to, but not underneath, your

child when installing the child seat rear facing. Use only

the outer buckle slot when installing forward facing.

GENERAL USAGE

• Follow all instructions on this child restraint and in the

written instructions.

• Register your child restraint with the manufacturer.

• In a vehicle with rear designated seating positions,

vehicle owners should be alerted that, according to

accident statistics, children are safer when properly

restrained in the rear seating positions than in the

front seating positions. To ensure your child’s safety,

please study Vehicle Seating Positions on page 31

and consult your vehicle owner’s manual.

• Always make sure the child restraint system is

secured to the vehicle, even when unoccupied, since

in a crash an unsecured child restraint system may

injure occupants.

• To prevent injury due to deterioration or hidden

damage, discontinue use of this child seat if it is

older than ten years or has been in a moderate or

severe crash (see below). See Serial Number and

Manufactured Date Label on child seat (pages 2-3).

• Prevent the Side Impact Cushions from being

punctured. Puncture damage will cause the cushions

not to perform as intended in a crash.

• The use of non-BRITAX covers, inserts, toys,

accessories, or tightening devices is not approved by

BRITAX. Their use could cause this child seat not to

perform as intended in a crash.

Important Notes

• Do not install with the lower anchors for a child weighing

more than 30 lbs (13.6 kg) rear facing or 35 lbs (15.8 kg)

forward facing.

• Ensure that the shell cover is properly secured behind

the red markers to allow for proper functioning of the

CLICKTIGHT mechanism (see page 35).

• Discontinue use of this child seat if it has been in a

moderate or severe crash. It is not necessary to replace a

car seat after a minor crash, deﬁned by the US National

Highway Trac Safety Administration (NHTSA) as:

a. The vehicle is drivable from the crash site; and

b. The vehicle door nearest the child seat was not

damaged; and

c. No vehicle occupants were injured; and

d. There is no visible damage to the child seat; and

e. The airbags (if present) did not deploy.

• Cover the child seat when the vehicle is parked in direct

sunlight. Metal parts of child seat could become hot

enough to burn a child.

• Store the child seat in a safe place when it is not being

used. Avoid placing heavy objects on top of it.

• Do not, except as described in this booklet, attempt to

disassemble any part of the child seat or change the way

the harness or vehicle’s seat belts are used.

• Never use the harness adjuster strap to lift or carry this

child seat. Doing so could cause damage to harness

adjuster and webbing. Always carry this child seat by its

shell or tether straps.

Registration

Child restraints could be recalled for safety reasons. You

must register this restraint to be reached in a recall. Send

your name, address, e-mail address if available and the

restraint’s model number and manufacturing date to

Britax Child Safety, Inc. P.O. Box 91167 Allentown, PA

18109-9925, or call 1-888-427-4829 or 1-704-409-1699,

or register online at www.BritaxUSA.com/registration. For

recall information, call the U.S. Government’s Vehicle Safety

Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to

http://www.NHTSA.gov.

For your convenience, record all the information about

your child seat below. Refer to the Serial Number &

Manufactured Date Label for all information (see page 2).

Model Name and Number: ______________________________

Serial Number: ________________________________________

Batch Number: ________________________________________

Date of Manufacture: ___________________________________

6 7

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Child Fit Information

Rear Facing: 5 – 40 lbs (2�3 – 18 kg)

The American Academy of Pediatrics recommends that all

infants and toddlers should ride in a Rear-Facing Car Seat

until they are 2 years of age or until they reach the highest

weight or height allowed by their car seat manufacturer.

BRITAX strongly recommends that children ride rear facing

to the highest weight or height speciﬁed.

Use rear facing:

• with harness straps in the closest

position at or below the child’s

shoulders and

• with children who weigh 5 – 40 lbs

(2.3 – 18 kg) and

• when the top of the child’s head is at

least 1 in. (2.5 cm) below the top of

the head restraint.

Forward Facing: 20 – 65 lbs (9�1 – 29�4 kg)

BRITAX strongly recommends that children should be

secured with a harness system until they exceed the weight

or height limits speciﬁed.

Use forward facing:

• with harness straps in the closest

position at or above the child’s

shoulders, parallel to level ground and

• with children who weigh 20 – 65 lbs

(9.1 – 29.4 kg) and

• who are 49 in. (124.5 cm) or less in

height and

• when the top of the ears are below the

top of the head restraint.

Certiﬁcation

This Restraint is Certiﬁed For Use in Motor Vehicles and

Aircraft�

Motor Vehicles

This child seat system conforms to all applicable Federal

motor vehicle safety standards (FMVSS 213).

Aircraft

This child seat is certiﬁed for aircraft use. The

FAA recommends that a child weighing up to

40 lbs (18 kg) use a certiﬁed, harnessed child

seat while traveling on an aircraft. Contact the

airline about their policy prior to traveling.

For rear-facing aircraft installation:

1. Recline this child seat (see page 25) and place rear-

facing on the aircraft seat.

2. Slide the aircraft lap belt into the

rear-facing belt slots over the cover

with the CLICKTIGHT in the closed

position.

3. Ensure the lap belt is not twisted,

buckle, and remove all slack.

For forward-facing aircraft

installation:

1. Place this child seat forward-facing on the aircraft seat in

the upright position.

2. Slide the aircraft lap belt into the

forward-facing belt slots under the

cover with the CLICKTIGHT in the

closed position.

3. Ensure the lap belt is not twisted,

buckle, and remove all slack.

NOTE: For further instructions on

securing your child and adjusting ﬁt

see page 20.

– Install your child seat in a window seat to avoid

blocking the aisle.

– If the aircraft lap belt is too short, ask a ﬂight attendant

for a belt extender.

– Your child may experience discomfort if the buckle

is located in the seating area of a the child seat after

installation.

– Inﬂatable aircraft lap belts are not compatible with this

child seat.

– This seat may not ﬁt all aircraft. Contact your airline

prior to travel to verify ﬁt.

NOTE: Use the

Seated Shoulder

Height Label on

the child seat as a

guide to determine

when your child

has reached the

top harness slot.

1 inch

2.5 cm

Shoulder

Level

Shoulder

Level

8 9

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Rear-Facing Installation

Lap-Shoulder Belt Installation

1. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open.

2. Recline the unoccupied

child seat and place rear

facing on the vehicle seat

(see page 25).

3. Slide both parts of the

vehicle belt into the rear-

facing belt slots.

4. Ensure the vehicle belt is

not twisted and buckle

the seat belt.

5. Remove slack from the

lap part (a), then the

shoulder part (b) of the

vehicle belt.

6. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure.

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Ensure that the ball in the recline indicator is within

the allowable blue section for the size of the child (see

page 25).

9 Check that all connections are secure and straps are

not twisted.

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

Rear-Facing Installation with Lap-Shoulder Belt

NOTE: Rear-facing

installations can be

improved by the use of

the tether (see page 29).

10 11

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Rear-Facing Installation with Lower Anchors

1. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open.

2. Recline the unoccupied

child seat and place rear-

facing on the vehicle seat

(see page 25).

3. Remove the lower

connectors from the

storage compartment at

the rear of the seat and

pull the strap to full length

toward the child’s left

side.

4. Slide the lower connector

strap into the rear-facing

belt slots and ﬁrmly press

the lower connectors

over their adjacent lower

anchors.

– Verify that the

connectors are secure

and the strap is not

twisted.

5. Pull the end of the lower

connector strap to

remove slack.

6. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure.

NOTE: Rear-facing

installations can be

improved by the use of

the tether (see page 29).

Lower Anchor Installation

IMPORTANT:

Do not install rear-facing with the lower

anchors for a child weighing more than 30 lbs (13.6 kg).

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Ensure that the ball in the recline indicator is within

the allowable blue section for the size of the child (see

page 25).

9 Check that all connections are secure and straps are

not twisted.

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

12 13

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Lap Belt Installation

1. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open

2. Recline the unoccupied

child seat and place rear-

facing on the vehicle seat

(see page 25).

3. Slide the vehicle belt into

the rear-facing belt slots.

4. Ensure the vehicle belt is

not twisted and buckle

the seat belt.

5. Lock and remove slack

from the vehicle belt.

NOTE: Ensure that the

vehicle belt is locked as

directed by your vehicle

owner’s manual.

6. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure.

Rear-Facing Installation with Lap Belt

NOTE: Rear-facing

installations can be

improved by the use of

the tether (see page 29).

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Ensure that the ball in the recline indicator is within

the allowable blue section for the size of the child (see

page 25).

9 Check that all connections are secure and straps are

not twisted.

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

14 15

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Forward-Facing Installation

Lap-Shoulder Belt Installation

1. Remove the tether

from the tether storage

compartment and retainer

tabs and place it up and

over the child seat back.

2. Recline the unoccupied

child seat and place

forward-facing on the

vehicle seat.

Ensure that

the base of the child seat

is ﬂat on the vehicle seat

and no more than 3 in.

(7.6 cm) of the base hangs

over the edge of the

vehicle seat

(see page 26)

3. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open.

4. Slide both parts of the

vehicle belt into the

forward-facing belt slots.

5. Ensure the vehicle belt is

not twisted and buckle

the seat belt.

6. Remove slack from the

lap part (a), then the

shoulder part (b) of the

vehicle belt.

7. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure

8. Attach the

tether

to a

designated anchor (see

vehicle owner’s manual)

and remove slack (see

page 29).

Forward-Facing Installation with Lap-Shoulder Belt

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Check that all connections are secure and straps are

not twisted.

9 Ensure that the ball in the recline indicator is within the

allowable green section and that no more than 3 in.

(7.6 cm) of the base hangs over the edge of the vehicle

seat (see page 26).

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

9 Check that any excess tether webbing is contained

within your vehicle and secured in the elastic strap.

16 17

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Lower Anchor Installation

IMPORTANT:

Do not install forward-facing with the lower

anchors for a child weighing more than 35 lbs (15.9 kg).

1. Remove the lower

connectors from the

storage compartment

at the rear of the seat

and pull the strap to

full length toward the

child’s left side.

2. Remove the tether

from the tether storage

compartment and retainer

tabs and place it up and

over the child seat back.

3. Recline the unoccupied

child seat and place

forward-facing on the

vehicle seat.

Ensure that

the base of the child seat

is ﬂat on the vehicle seat

and no more than 3 in.

(7.6 cm) of the base hangs

over the edge of the

vehicle seat

(see page 26)

4. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open.

5. Slide the lower connector

strap into the rear-facing

belt slots and ﬁrmly press

the lower connectors

over their adjacent lower

anchors.

– Verify that the

connectors are secure

and the strap is not

twisted.

6. Pull the end of the lower

connector strap to

remove slack.

7. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure

8. Attach the

tether

to a

designated anchor (see

vehicle owner’s manual)

and remove slack (see

page 29).

Forward-Facing Installation with Lower Anchors

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Check that all connections are secure and straps are

not twisted.

9 Ensure that the ball in the recline indicator is within the

allowable green section and that no more than 3 in.

(7.6 cm) of the base hangs over the edge of the vehicle

seat (see page 26).

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

9 Check that any excess tether webbing is contained

within your vehicle and secured in the elastic strap.

18 19

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Lap Belt Installation 7. Close the CLICKTIGHT.

– A click conﬁrms the

CLICKTIGHT is secure

NOTE: If the CLICKTIGHT

is dicult to close, repeat

step 6 with less tension in

the vehicle belt.

8. Attach the

tether

to a

designated anchor (see

vehicle owner’s manual)

and remove slack (see

page 29).

1. Remove the tether

from the tether storage

compartment and retainer

tabs and place it up and

over the child seat back.

2. Place the unoccupied child

seat forward-facing on the

vehicle seat in the upright

position.

Ensure that the

base of the child seat is

ﬂat on the vehicle seat and

no more than 3 in. (7.6 cm)

of the base hangs over the

edge of the vehicle seat

(see page 26)

3. Open the CLICKTIGHT.

a. Press the dimple on

the CLICKTIGHT

dial.

b. Rotate dial clockwise

until CLICKTIGHT

releases and lift to

open.

4. Slide the vehicle belt into

the forward-facing belt

slots.

5. Ensure the vehicle belt is

not twisted and buckle

the seat belt.

6. Push down into the

middle of the child seating

area with moderate

force (approximately

45 lbs/20.4 kg),

compressing the vehicle

seat while tightening the

vehicle belt.

NOTE: Ensure that the

vehicle belt is locked as

directed by your vehicle

owner’s manual.

Forward-Facing Installation with Lap Belt

9 Ensure that the logo on the CLICKTIGHT dial has

returned to a horizontal position.

9 Check that all connections are secure and straps are

not twisted.

9 Ensure that the ball in the recline indicator is within the

allowable green section and that no more than 3 in.

(7.6 cm) of the base hangs over the edge of the vehicle

seat (see page 26).

9 Check that the child seat cannot be moved front to

back or side to side more than 1 in. (2.5 cm) at the belt

path. If the child seat is not secure, repeat installation

or use a dierent seating location.

9 Check that any excess tether webbing is contained

within your vehicle and secured in the elastic strap.

20 21

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Securing Your Child

IMPORTANT: Impact absorbing chest pads are highly

recommended for forward-facing mode. Removal of chest

pads is optional for rear-facing mode to ensure a snug ﬁt

for small infants.

7. Fasten the harness

buckle. Proper

connection is conﬁrmed

with a click after inserting

each buckle tongue.

8. Check for proper harness

height and pull any

excess slack up to the

child’s shoulder area

before tightening.

9. Pull the harness adjuster

strap to tighten the

harness. The Click

& Safe indicator will

click when the harness

is within range of

appropriate snugness

NOTE: The harness

should have a snug ﬁt

around the child. A snug

strap should not allow any

slack. It lies in a relatively

straight line without

Before traveling, verify that the:

9 Harness straps are not twisted.

9 Harness is snug.

9 Buckle is fastened.

9 Chest clip is at the child’s armpit level.

1. Make the proper

adjustments to the

harness and buckle (see

pages 23-24).

2. Loosen the harness.

a. Press harness

adjuster button.

b. Pull both harness

straps forward.

3. Open the chest clip.

a. Press tabs.

b. Pull apart.

4. Release the buckle and

attach the harness straps

to the harness holders.

5. Place the child in the child

seat. Ensure the child

is positioned upright in

the child seat and not

slouching. Their bottom

must touch the child seat,

and their back must rest

ﬂat against the back of the

child seat.

6. Position the harness

straps around the child.

IMPORTANT: Adjust the

harness to ﬁt the clothes

the child is wearing.

Remove bulky coats and/

or jackets before putting

the child in the child seat.

Pull the harness adjuster

strap out from the child

seat to tighten�

Do not pull sideways�

sagging. It does not press on the child’s ﬂesh or push

the child’s body into an unnatural position. You should

not be able to pinch excess.

10. Fasten the chest clip and

place the chest pads in a

comfortable position for

the child within the range

of a correctly placed chest

clip.

NOTE: The correct height for the chest clip is at the

middle of the chest at armpit level.

ADVOCATE CLICKTIGHT User Guide

BRITAX Child Safety, Inc.

Adjusting the Harness Height

• In rear-facing mode, the harness straps should be in

the closest position at or below your child’s shoulders.

See page 7.

• In forward-facing mode, the harness straps should

be in the closest position at or above your child’s

shoulders. See page 7.

1. Loosen the harness.

a. Push harness adjuster

button.

b. Pull both harness

straps forward.

2. Squeeze the harness

height adjuster, slide the

harness into the desired

position and release.

3. Ensure the harness has

locked into position.

Child Seat Functions

Click & Safe

Snug Harness Indicator

IMPORTANT: See page 20 for detailed instructions on

securing your child.

The Click & Safe is designed to sense tension when the

adjuster strap is pulled and will provide an audible indication

when the child seat harness is within range of appropriate

snugness. The harness should have a comfortable but snug

ﬁt around the child. A snug strap should not allow any slack.

It lies in a relatively straight line without sagging. It does not

press on the child’s ﬂesh or push the child’s body into an

unnatural position. You should not be able to pinch excess

webbing at the shoulder. Follow the steps below to tighten

the harness.

To tighten the harness:

1. Remove any bulky clothing

from your child before

tightening the harness.

2. Check for proper harness

height.

3. Pull any excess slack in the

harness up to the child’s

shoulder area.

4. Pull the harness adjuster strap straight out from the

child seat until a click is heard. The Click & Safe

indicator will click when the harness is within range

of appropriate snugness�

NOTE: If there is still slack in the harness, repeat the

steps above until another click indicates a snug harness.

It may be necessary to double check that the harness is

within range of appropriate snugness. Always conﬁrm

a snug ﬁt by attempting to pinch excess webbing in the

shoulders.

9 Check that the harness is buckled and secure.

9 Check that the harness is snug and you can not pinch

excess webbing at the shoulder.

NOTE: Harness length can be extended if necessary for

children over the age of 2. For more information, contact

BRITAX Consumer Services at 1-888-427-4829 or 1-704-

409-1699.

24 25

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Using the Harness Buckle

To Fasten:

1. Insert one tongue at a

time into the buckle.

Proper connection is

conﬁrmed with a click

after inserting each

buckle tongue.

To Release:

1. Press the release button

and pull the tongues from

the buckle.

NOTE: Periodically clean

the buckle to ensure

proper operation. See

page 42.

Using the Chest Clip

1. Open the chest clip.

a. Press tabs.

b. Pull apart.

2. Push together

to fasten.

NOTE: Always

position the

chest clip at

armpit level.

Comfort Pillow

The comfort pillow is designed

to provide better ﬁt and

comfort for infants using this

child seat.

NOTE: Remove the comfort

pillow after the child can sit

comfortably in the child seat

without additional support.

Seat Positions

This child seat has 7 recline positions. To adjust the recline

position:

1. Pull the recline handle

then rotate the child seat

shell until the ball in the

recline indicator is in the

allowable section for:

• Rear Facing - Light

Blue (Infants), or

Dark Blue (larger

children with head and neck control)

• Forward Facing - Green

2. Release the recline handle, then verify the child seat has

locked into position.

NOTE: Set the seat position BEFORE installing.

Rear-Facing

In rear-facing installations

it is important that the child

seat be reclined to maintain

proper head and neck

control with smaller infants.

Use the recline indicator on

the child seat to help achieve

an acceptable recline angle,

with the

ball in the recline indicator in the allowable blue

section for the size of the child.

Toddler Infant

Harness Buckle Position

The child seat shell contains an inner buckle slot and an outer

buckle slot.

• For rear-facing installations,

position the buckle in the

slot closest to but not under

the child.

• For forward-facing

installations, use the outer

buckle slot only.

Reposition the harness buckle by following the steps on

pages 37-38.

NOTE: NEVER leave the buckle in the adjustment slot.

ADJUSTMENT

SLOT

INNER SLOT

OUTER SLOT

26 27

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

Forward-Facing

In forward-facing

installations, it is

important that the base

of the child seat rests

completely ﬂat on the

vehicle seat. As seen

in the illustration, it is

permissible to allow up

to 3 in. (7.6 cm) of the

base to hang over the

edge of the vehicle seat.

Some vehicle seats do

not allow enough of the child seat base to contact the vehicle

seat. If this is the case, adjust the recline angle to a more

upright position. Not doing so could cause the child seat to

not perform as intended. Use the recline indicator on the child

seat to help achieve an acceptable recline angle, with the

ball

in the recline indicator in the allowable green section

In some cases, the vehicle head

restraint can prevent the child seat

head restraint from being raised

high enough to properly adjust the

harness for the ﬁt of your child when

using a forward facing reclined

position. DO NOT force the child

seat head restraint past the vehicle

head restraint. Doing so could cause the child seat not to

perform as intended. If the location of the vehicle head

restraint interferes with the child seat head restraint, raise

or remove the vehicle head restraint. If the vehicle head

restraint cannot be removed, move the child seat to the

upright position or try a dierent seating location.

Acceptable

Overhang

Unacceptable

Overhang

3”

Using the Lower Anchors and Tethers for Children (LATCH)

The Lower Anchors and Tethers for Children or LATCH, is a

system available on this child seat that oers an alternative

to vehicle seat belt installation methods. The ﬁgure below

shows typical locations for lower anchors and tether anchors

in a vehicle. See pages 2-3 for LATCH components on this

child seat.

Check your vehicle owner’s manual to learn if it is equipped

with LATCH, the maximum weight rating for the lower

anchors, tether anchors capacities, and information on the

lower anchor locations and designated seating positions

available for use with this child seat.

Lower Connectors

Using the Lower Connectors

The lower connectors are located in the back of the base

of the child seat. Store the connector assembly in the

compartment when not in use.

To attach the lower connectors:

1. Remove the lower

connectors from the

storage compartment at

the rear of the seat and

pull the strap to full length

toward the child’s left

side.

2. Press the lower connector

hook over its adjacent

lower anchor. For full

installation instructions see

pages 10-11 or 16-17.

LATCH SYSTEM ANCHOR LOCATIONS

Tether

Anchor

Lower

Anchors

Lower Anchors

11 in. (27.9 cm)

28 29

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

To remove the lower

connectors:

1. Push the lower connector

adjuster release button

to loosen the lower

connector strap.

2. Squeeze the lower

connector hook and lift o

the lower anchor.

Impact Absorbing Tether

Failure to follow the guidelines below may cause the child

seat not to perform as intended.

• BRITAX recommends that the tether be used at all

times when installing the child seat. Using the tether

will improve the stability of your child seat and reduce

the risk of injury.

• Attach the tether only to tether anchors identiﬁed by

your vehicle manufacturer as tether anchorage points.

Only use the designated tether anchor for each seating

position.

• If your vehicle does not currently have a tether anchor

attachment, refer to your vehicle owner’s manual or

contact your vehicle man u fac tur er for assistance. DO

NOT modify your vehicle without advice from your

vehicle manufacturer.

• Store the tether in the compartment on the back of the

child seat when not in use.

Tether anchor locations vary from

vehicle to vehicle. Check your vehicle

owner’s manual for tether anchor

capacities and look for the tether

anchor symbol shown in the diagram

to help identify where the top tether

anchor points are located in your

vehicle. See the diagrams below for

possible rear and forward-facing tether

installation conﬁgurations.

Rear-Facing Tether Connector Strap

Because every vehicle model is dierent, locations to

anchor the tether for rear-facing installations may vary. Use

the rear-facing tether connector strap to assist in creating an

anchor point for rear-facing conﬁguration “A” above.

1. Find a ﬁxed location in the vehicle that is bolted to the

ﬂoor. If you cannot ﬁnd a location to create an anchor

point, contact the vehicle manufacturer to identify a

tether connection point.

2. Route the strap through the anchor

point.

3. Thread the loop at one end of the strap

through the loop at the other end and

pull until the strap is tight.

4. Use the open loop as an

attachment point for the

tether.

NOTE: Store the tether

connector strap in the tether

compartment when not in

use.

Using the Tether

To attach the tether to a tether anchor:

(A) Rear Facing

(B) Rear Facing

Tether Conﬁgurations

1. Firmly press the hook

over the tether anchor

point.

2. Pull the loose end of the

webbing to remove slack

from the tether.

NOTE: If the tether is

too short for use in your

vehicle, contact BRITAX

Consumer Services at

1-888-427-4829 or 1-704-

409-1699 to obtain a

tether extender.

30 31

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

To remove the tether from a tether anchor:

1. Loosen the tether.

a. Tilt the lock up.

b. Pull the tether webbing.

2. Remove the tether hook

from the tether anchor.

NOTE: Store the tether in the tether compartment when

not in use and ensure the tether compartment door is

fully closed.

The Tether as a Crash Indicator

The tether can indicate when the child seat has been in a

moderate or severe crash (see “Important Notes” on page 5)

and replacement of the child seat is necessary.

Figure 1 shows a tether

acceptable for continued use

(provided the child seat has

not been involved in a crash).

The colored stitching will be

intact and not visible from the

back of the seat.

Figure 2 shows examples

of when the tether has been

damaged and is unacceptable

for continued use. If one or

both of the loops have pulled

through the back of the shell

and/or any of the colored

stitching has ripped, the child

seat is no longer acceptable

for use.

IMPORTANT: Discontinue use of child seat if it has been

involved in a moderate or severe crash, regardless of

whether the loops have pulled through the back side of the

shell and the colored stitching has been ripped.

Vehicle Compatibility

Vehicle Seating Positions

DO NOT place child seat rear-facing

in the front seat of a vehicle with

a passenger air bag. DEATH or

SERIOUS INJURY can occur. Owners

of vehicles with front passenger side

airbags should refer to their owner’s

manual for child restraint installation

instructions. The back seat is the

safest place for children 12 and under.

Some vehicles have no seating positions which are

compatible with this child seat. If in doubt, contact the

vehicle manufacturer for assistance.

Forward-facing vehicle seats MUST be used with this

child seat. Side-facing or rear-facing seats CANNOT be

used. See the diagram below.

ADVOCATE CLICKTIGHT User Guide

BRITAX Child Safety, Inc.

Incompatible Vehicle Seat Belts

Vehicle seats and seat belts dier from vehicle to vehicle.

Refer to your vehicle owner’s manual for speciﬁc information

about your vehicle seat belts and their use with child seats.

The following types of vehicle seat belts are NOT

compatible with this child seat. If any of the belt types

listed below are in the chosen seating position, choose

another vehicle seating position or check your vehicle

owner’s manual for information on installing a car seat in

your vehicle.

NOTE: This BRITAX car seat may not be compatible with

every inﬂatable lap-shoulder belt. See FAQs in the support

section of the BRITAX website (www.britaxusa.com/support)

for additonal instructions.

Motorized, automatic

vehicle seat belts�

Lap belts forward of

the vehicle seat bight�

Lap-shoulder belts with

top or bottom anchor

points on the vehicle door�

Lap belts with a sewn-in

latch plate that have a

retractor that locks only

in case of a sudden stop�

Maintenance

Cover

Removing the Cover

Never remove the buckle tongues from the harness.

They cannot be reattached after removal. If reassembled

incorrectly, the child seat may not perform as intended.

1. Loosen and unbuckle the

harness.

a. Push harness

adjuster button.

b. Pull both harness

straps forward.

c. Unbuckle the

harness.

2. Open the chest clip.

a. Press tabs.

b. Pull apart.

3. Remove the comfort

pillow and comfort pads if

necessary.

4. Remove the belly pad and

buckle.

a. Open the

CLICKTIGHT and

remove the two

elastic loops on

the bottom of the

CLICKTIGHT.

b. Lift the front of

the seat cover

and pull over the

CLICKTIGHT bezel

to access the buckle

strap connection.

c. Remove the harness

buckle by turning

the buckle strap

sideways and routing

the retainer out of

the front buckle slot

in the child seat (see

page 37).

34 35

BRITAX Child Safety, Inc. ADVOCATE CLICKTIGHT User Guide

d. Pull the end of the

belly pad and buckle

retainer out of the

buckle slot in the

cover to remove.

– Turn the buckle

retainer sideways

and slide the buckle

out of the belly pad

(see page 38).

e. Remove seat cover.

5. Detach the hook and loop

fasteners on the head

restraint from around the

harness.

6. Remove the head

restraint.

a. Raise the harness to

the highest position.

b. Detach the elastic

straps from the rear

of the head restraint.

7. Ensure the CLICKTIGHT

is open and remove the

lower shell cover.

a. Detach elastic loops

at front of shell.

b. Lift up from the front

to remove the lower

shell cover.

c. Pull cover up at

sides and around

rear-facing belt

paths.

8. Lower the harness, reach

around the head restraint,

and pull the upper shell

cover towards you to

remove.

Replacing the Cover

1. Attach one side of the

upper shell cover at the

forward-facing belt path,

pull the cover over the

back of the shell, and

secure at opposite belt

path.

2. Replace lower shell cover.

a. Open the

CLICKTIGHT.

b. Tuck one of the plastic

tabs on the lower

shell cover into the

outer side of the shell

between the forward

and rear-facing belt

paths.

c. Tuck the lower shell

cover around the inner

and outer sides of the

shell from the forward-

facing belt paths to the

front of the child seat.

d. Continue replacing

the lower shell cover

around the seat to the

other forward-facing

belt path and tuck the

second plastic tab

into the shell between

the forward and rear-

facing belt paths.

IMPORTANT:

Ensure shell cover is

secured behind red

markers to allow for

proper function of

CLICKTIGHT.

e. Thread the harness

adjuster strap through

the front of the lower

shell cover.

Page is loading ...

Britax Advocate ClickTight User guide

Brand: Britax

Model: Advocate ClickTight

Category: Car seat

Type: User guide

Download PDF

report

in other languages

español: Britax Advocate ClickTight Guía del usuario

Britax Advocate ClickTight User guide

Britax Advocate ClickTight User guide

in other languages

Related papers

Other documents