Milwaukee 2665-20 User manual

Brand: Milwaukee

Model: 2665-20

Category: Power impact wrenches

Type: User manual

Page is loading ...

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

•Keepworkareacleanandwelllit. Cluttered or

dark areas invite accidents.

•Donotoperatepowertoolsinexplosiveat-

mospheres,suchasinthepresenceofam-

mableliquids,gasesordust. Power tools create

sparks which may ignite the dust or fumes.

•Keepchildren and bystanders awaywhile

operatingapowertool. Distractions can cause

you to lose control.

•Powertoolplugsmustmatchtheoutlet.Never

modifythepluginanyway.Donotuseany

adapterplugswithearthed(grounded)power

tools.Unmodied plugs and matching outlets will

reduce risk of electric shock.

•Avoidbodycontactwithearthedorgrounded

surfacessuchaspipes,radiators,rangesand

refrigerators.There is an increased risk of electric

shock if your body is earthed or grounded.

•Donotexposepowertoolstorainorwetcondi-

tions.Water entering a power tool will increase

the risk of electric shock.

•Donotabusethecord.Neverusethecordfor

carrying,pullingorunpluggingthepowertool.

Keepcordawayfromheat,oil,sharp edges

ormovingparts.Damaged or entangled cords

increase the risk of electric shock.

•Whenoperatingapowertooloutdoors,usean

extensioncordsuitableforoutdooruse.Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

•Ifoperatingapowertoolinadamplocation

isunavoidable,usearesidualcurrentdevice

(RCD)protectedsupply.Use of an RCD reduces

the risk of electric shock.

attached to a rotating part of the power tool may

result in personal injury.

•Donot overreach. Keep properfooting and

balanceatalltimes. This enables better control

of the power tool in unexpected situations.

•Dressproperly.Donotwearlooseclothingor

jewellery.Keepyourhair,clothingandgloves

awayfrommovingparts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

•If devices are provided for the connection of

dustextractionandcollectionfacilities,ensure

theseareconnectedandproperlyused.Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failuretofollowthewarningsandinstructionsmayresultinelectricshock,reand/or

seriousinjury.Save all warnings and instructions for future reference.

Theterm"powertool"inthewarningsreferstoyourmains-operated(corded)powertoolor

battery-operated(cordless)powertool.

POWER TOOL USE AND CARE

•Donotforcethepowertool.Usethecorrect

powertool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

•Donotusethepowertooliftheswitchdoesnot

turnitonandoff. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

•Disconnect the plug from the powersource

and/orthe battery packfromthepower tool

beforemaking any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

•Storeidlepowertoolsoutofthereachofchil-

drenanddonotallowpersonsunfamiliarwith

thepowertoolortheseinstructionstooperate

thepowertool.Power tools are dangerous in the

hands of untrained users.

•Maintainpowertools.Checkformisalignment

orbindingofmovingparts,breakageofparts

andany other conditionthat may affectthe

powertool’soperation.Ifdamaged,havethe

powertoolrepairedbeforeuse.Many accidents

are caused by poorly maintained power tools.

•Keepcuttingtoolssharpandclean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

•Usethepowertool,accessoriesandtoolbits

etc., in accordance with these instructions,

takingintoaccounttheworkingconditionsand

theworktobeperformed.Use of the power tool

for operations different from those intended could

result in a hazardous situation.

•Stayalert,watchwhatyouaredoinganduse

commonsensewhenoperatingapowertool.Do

notuseapowertoolwhileyouaretiredorunder

theinuenceofdrugs,alcoholormedication.A

moment of inattention while operating power tools

may result in serious personal injury.

•Use personal protective equipment.Always

weareyeprotection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

•Preventunintentional starting. Ensure the

switchisintheoff-positionbeforeconnecting

topowersourceand/orbatterypack,picking

uporcarryingthetool.Carrying power tools with

your nger on the switch or energising power tools

that have the switch on invites accidents.

•Removeanyadjustingkeyorwrenchbefore

turningthepowertoolon.A wrench or a key left

•Rechargeonlywiththechargerspeciedby

themanufacturer.A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

•Usepowertoolsonlywithspecicallydesig-

natedbattery packs.Use of any other battery

packs may create a risk of injury and re.

BATTERY TOOL USE AND CARE

•Hold power toolby insulated grippingsur-

faces,whenperforminganoperationwherethe

fastenermaycontacthiddenwiring.Fasteners

contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

• Wear ear protectors. Exposure to noise can

cause hearing loss.

•Keephandsawayfromallcuttingedgesand

movingparts.

•Maintainlabels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to lter out microscopic particles.

Cat. No. Volts DC RPM DriveShank IPM

2662-20

2663-20

2664-20

2665-20

0 - 2000

1/2" Square

3/4" Square

7/16" Hex

0 - 2500

FUNCTIONAL DESCRIPTION

SYMBOLOGY

SPECIFICATIONS

SPECIFIC SAFETY RULES

•Whenbatterypackisnotinuse,keepitaway

fromother metal objects like paper clips,

coins,keys,nails,screws,orothersmallmetal

objectsthatcanmakeaconnectionfromone

terminaltoanother.Shorting the battery termi-

nals together may cause burns or a re.

•Underabusiveco

nditions,liquidmaybeeject-

edfromthebattery;avoidcontact.Ifcontactac-

cidentallyoccurs,ushwithwater.Ifliquidcon-

tactseyes,additionallyseekmedicalhelp.Liquid

ejected from the battery may cause irritation or burns.

SERVICE

•Haveyourpowertoolservicedbyaqualied

repairpersonusingonlyidenticalreplacement

parts.This will ensure that the safety of the power

tool is maintained.

Volts

Direct Current

Impacts per Minute Under

Load (IPM)

No Load Revolutions per

Minute (RPM)

Underwriters Laboratories, Inc.

United States and Canada

1. Trigger

2. Control switch

3. Drive Shank

ASSEMBLY

WARNING Recharge onlywith the

chargerspeciedforthebattery.Forspecic

charginginstructions,read the operator’s

manualsuppliedwithyourchargerandbattery.

Inserting/RemovingtheBattery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING Always remove battery

packbeforechangingorremovingaccesso-

ries.Onlyuseaccessoriesspecicallyrecom-

mendedforthistool.Othersmaybehazardous.

AttachingandRemovingtheToolHanger

1. To attach, remove the two top gear case screws.

2. Place the ring through the tool hanger.

3. Position the tool hanger on the tool over the two

gear case screw holes.

4 Replace the two gear case screws. Hand tight-

en the screws.

5. To remove, reverse the procedure.

OPERATION

WARNING Always remove battery

packbeforechangingorremovingaccesso-

ries.Onlyuseaccessoriesspecicallyrecom-

mendedforthistool.Othersmaybehazardous.

WARNING Toreducetheriskofinjury,

wearsafetygogglesorglasseswithsideshields.

UsingControlSwitch

The control switch may be set to three positions: for-

ward, reverse and lock. Due to a lockout mechanism,

the control switch can only be adjusted when the trig-

ger is not pressed. Always allow the motor to come

to a complete stop before using the control switch.

1. For forward(clockwise) rotation, push the con-

trol switch from the right side of the tool. Check

the direction of rotation before use.

2. For reverse (counterclockwise) rotation, push

the control switch from the left side of the tool.

Check the direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when

the control switch is in the locked position.

Always remove the battery pack before perform-

ing maintenance, changing accessories, storing

the tool and any time the tool is not in use.

Starting,StoppingandControllingSpeed

These tools may be operated at any speed from

0 to full speed.

1. To start the tool, pull the trigger.

2. To varythe driving speed, increase or decrease

pressure on the trigger. The further the trigger is

pulled, the greater the speed.

3. To stop the tool, release the trigger.

ImpactingTechniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length of

time required to reach the desired torque. Check the

tightness with a hand-torque wrench. If the fasten-

ers are too tight, reduce the impacting time. If they

are not tight enough, increase the impacting time.

Oil, dirt, rust or other matter on the threads or under the

head of the fastener affects the degree of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for nal tightening.

WARNING Useonlysocketsandother

accessoriesspecicallydesignedforuseon

impactwrenchesanddrivers.Othersockets

andaccessoriesmightshatterorbreakcaus-

inginjury.

AttachingandRemovingAccessories

These tools are intended only for use with acces-

sories designed for impact wrenches and drivers.

Other sockets could shatter or break, causing injury.

Cat. No. 2662-20

1. Use only the appropriate size

Square Drive Sockets.

2. To attach a socket, align the hole

in the accessory with the detent

pin on the drive shank. Hold the

detent pin in while pushing the

socket onto the drive shank. The

detent pin will snap into place

in the hole to secure the socket.

3. To remove the socket, insert a nail or

other thin object into the hole in the

accessory and press in the detent

pin. Pull the accessory off the drive

shank.

Cat.No.2663-20,2664-20

1. Use only the appropriate size Square Drive Sockets.

2. To attach a socket, align the accessory with the

drive shank and push it rmly over the retaining ring.

3. To remove the accessory, pull the accessory off

the drive shank.

Cat. No. 2665-20

This driver is intended for use with drill and driver

bits with a 7/16" hex shank and ball detent recess.

1. To attach an accessory, pull the ring out and

insert the accessory shank. Release the ring. It

may be necessary to pull the bit out slightly to

engage the holding mechanism.

2. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or service center.

WARNING Alwaysremovebatterypack

beforechanging or removing accessories.

Onlyuseaccessoriesspecicallyrecommend-

edfor this tool. Others may be hazardous.

MaintainingTool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

After six months to one year, depending on use,

return the tool, battery pack and charger to A

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger, motor)

• Testing to assure proper mechanical and electrical

operation

If the tool does not start or operate at full power

with a fully charged battery pack, clean the contacts

on the battery pack. If the tool still does not work

properly, return the tool, charger and battery pack,

to a MILWAUKEE service facility for repairs.

MAINTENANCE

Cleaning

Clean dust and debris from charger and tool vents.

Keep tool handles clean, dry and free of oil or

grease. Use only mild soap and a damp cloth to

clean the tool, battery pack and charger since certain

cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include

gasoline, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and house-

hold detergents containing ammonia. Never use

ammable or combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center.

WARNING Toreducetheriskofper-

sonalinjuryanddamage,neverimmerseyour

tool,batterypackorchargerinliquidorallow

aliquidtoowinsidethem.

WARNING Toreducetheriskofinjury,

alwaysunplugthechargerandremovethebat-

terypackfromthechargerortoolbeforeper-

forminganymaintenance.Neverdisassemble

thetool,batterypackorcharger.Contacta

MILWAUKEEservicefacilityforALLrepairs.

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.

This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you pur-

chased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the

original proof of purchase to the ASC.

Call toll-free 1 800 832 1949 to nd the nearest ASC, for service, parts, accessories or components.

Proceduretomakethiswarrantyvalid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you pur-

chased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all

freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a) When the product is used in a different manners from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modied or repaired by people not authorized by TECHTRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Ph. 52 55 4160-3547

IMPORTED AND COMMERCIALIZED BY:

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

LIMITED WARRANTY - USA AND CANADA

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

Model:

DateofPurchase:

DistributororStoreStamp:

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct

CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is war-

ranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain

exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is

determined by MILWAUKEE to be defective in material or workmanship for a period of ve (5) years* after the

date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center

location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the

proof of purchase should be included with the return product. This warranty does not apply to damage that

MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized

personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Indus-

trial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED

Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb

fails the Work Light or Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline

Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,

Reconditioned product and Test & Measurement products. There are separate and distinct warranties avail-

able for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.

The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is

provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A

CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT

AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MIL-

WAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR

ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE

OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY

CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN-

CIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN

OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH

IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS

DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-

waukeetool.com or call 1.800.SAWDUST(1.800.729.3878) to locate your nearest service facility for warranty

and non-warranty service on a Milwaukee electric power tool.

Page is loading ...

MILWAUKEEELECTRICTOOLCORPORATION

13135WestLisbonRoad•Brookeld,Wisconsin,U.S.A.53005

58-14-2665d7 08/14 Printed in China

961011375-01( )

UNITED STATES

MILWAUKEEService

CANADA - ServiceMILWAUKEE

MILWAUKEE prides itself in producing a premium

quality product that is NothiNg But heavy Duty

Your satisfaction with our products is very impor-

tant to us!

If you encounter any problems with the operation

of this tool, or you would like to locate the factory

Service/Sales Support Branch or authorized ser-

vice station nearest you, please call...

1.800.268.4015

Monday – Friday 7:00 – 4:30 CST

fax: 866.285.9049

MilwaukeeElectricTool(Canada)Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with your

tool and accessory needs. Call 1.800.268.4015 to

nd the names and addresses of the closest re-

tailers or consult “Where to buy” on our Web site

www.milwaukeetool.com

MILWAUKEE est er de proposer un produit de

première qualité NothiNg But heavy Duty

. Votre

satisfaction est ce qui compte le plus!

En cas de problèmes d’utilisation de l’outil ou pour

localiser le centre de service/ventes ou le centre

d’entretien le plus proche, appelez le...

1.800.268.4015

Lundi – Vendredi 7:00 – 4:30 CST

fax: 866.285.9049

MilwaukeeElectricTool(Canada)Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Notre réseau national de distributeurs agréés se

tient à votre disposition pour fournir l’aide tech-

nique, l’outillage et les accessoires nécessaires.

Composez le 1.800.268.4015 pour obtenir les

noms et adresses des revendeurs les plus proches

ou bien consultez la section «Où acheter» sur notre

site web à l’adresse www.milwaukeetool.com

CENTRO DE ATENCIÓN A CLIENTES

Av Presidente Mazarik 29 Piso 7

11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Telefono 52 55 4160-3547

e-mail: [email protected]

Adicionalmente, tenemos una red nacional de

distribuidores autorizados listos para ayudarle con

su herramienta y sus accesorios. Por favor, llame

al 01 800 832 1949 para obtener los nombres y

direcciones de los más cercanos a usted, o con-

sulte la sección ‘Where to buy’ (Dónde comprar)

de nuestro sitio web en

www.ttigroupmexico.com

MILWAUKEE prides itself in producing a premium

quality product that is NothiNg But heavy Duty

Your satisfaction with our products is very impor-

tant to us! If you encounter any problems with the

operation of this tool, or you would like to locate the

factory Service/Sales Support Branch or authorized

service station nearest you, please call...

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with

your tool and accessory needs. Check your “Yellow

Pages” phone directory under “Tools-Electric” for

the names & addresses of those nearest you or see

the 'Where To Buy' section of our website.

1-800-SAWDUST

(1.800.729.3878)

Monday-Friday

7:00 AM - 6:30 PM

Central Time

or visit our website at

www.milwaukeetool.com

For service information, use the 'Service Center

Search' icon found in the 'Parts & Service' section.

Contact our Corporate After Sales Service

TechnicalSupportabout...

•Technical Questions

•Service/Repair Questions

•Warranty

call: 1-800-SAWDUST

fax:1.800.638.9582

email:[email protected]

www.milwaukeetool.comand...

• receive important notications regarding

your purchase

• ensure that your tool is protected under the

warranty

• become a heavy Duty club member

MEXICO - Soporte de Servicio MILWAUKEE

Registresuherramientaenlínea,en

www.ttigroupmexico.comy...

• reciba importantes avisos sobre su compra

• asegúrese de que su herramienta esté prote-

gida por la garantía

• conviértase en integrante de Heavy Duty

Milwaukee 2665-20 User manual

Brand: Milwaukee

Model: 2665-20

Category: Power impact wrenches

Type: User manual

Download PDF

report

in other languages

français: Milwaukee 2665-20 Manuel utilisateur
español: Milwaukee 2665-20 Manual de usuario

Milwaukee 2665-20 User manual

Milwaukee 2665-20 User manual

in other languages

Related papers

Other documents