Renkforce 2 ports Serial interface PCI Owner's manual

Brand: Renkforce

Model: 2 ports Serial interface PCI

Category: Interface cards/adapters

Type: Owner's manual

Page is loading ...

• Also observe the safety and operating instructions of any other devices which are connected

to the product.

• Consult an expert when in doubt about operation, safety or connection of the device.

• Maintenance, modications and repairs are to be performed exclusively by an expert or at a

qualied shop.

• If you have questions which remain unanswered by these operating instructions, contact our

technical support service or other technical personnel.

Hardware Installation

1. Turn off your computer and all devices connected to it.

2. Remove the computer’s cover. Refer to your computer user’s manual for more details.

3. Locate an available PCI slot and remove the metal bracket. Save the bracket screw for later use.

4. Align the card horizontally with respect to the PCI slot and insert it into the slot rmly and evenly. Take

care not to force it into the slot. Once you have properly positioned the card into the slot, secure the card

with the bracket screw you have saved.

5. Replace the computer’s cover.

6. Turn your computer on. You are now ready to install the driver.

Driver Installation

For detailed installation procedures of all operating systems, please refer to the

printed manufacturer’s manual or the installation guide included in the CD, under

D:\Moschip\MCS9865.

Installing Driver for Windows Vista 32/64-bit and Server 2008 32/64 bit:

1. Once Windows is running, insert the driver CD into the CD-ROM drive, assuming drive D.

2. Windows will automatically detect the product. Select “Locate and install driver software

(recommended)” and click Continue, then select “I don’t have the disc. Show me other options”.

3. Click on “Browse my computer for driver software (advanced)”, and then browse to the following

folder on the driver CD. Assuming that the operating system used is Windows Vista 32-bit, go to the

following folder:

D:\Moschip\MCS9865\Vista_Server2008\Windows32Bit\PciSetup.exe

4. Click the Next to continue.

5. Follow the on-screen instruction until the driver is install completely.

6. Select “Install this driver software anyway” when Vista prompts the following: “Windows can’t verify

the publisher of this driver software”.

7. Finally click Close when all the drivers have been installed.

Installing Driver for Windows 2000, XP 32/64-bit and Server 2003 32/64bit:

1. Start Windows and insert the Driver CD into the CD-ROM drive, assume drive D.

2. Windows will automatically detect the product. Select “No, not this time” and click the Next button to

continue.

3. Select “Install from a list or specic location (Advanced)” and click on the Next button.

4. Do not select “Search removable media” and select only “Include this location in the search”, and

then click the Browse button select the location for the drivers, assuming the operating system used is

Windows XP 32bit:

D:\Moschip\MCS9865\Win2K_XP_Server2003\Windows32Bit\ PciSetup.exe

5. Click OK button to conrm and click Next button to continue.

6. If the wizard asks for Windows Logo testing to verify compatibility, click Continue Anyway.

7. Click Finish button to nish installing driver.

8. Once driver installation is completed, you can now connect your external devices to the PCI multi- I/O

card. To install the driver for the external devices, please refer to the external device user’s manuals.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the household waste. At

the end of its service life, dispose of the product according to the relevant statutory regulations.

You thus full your statutory obligations and contribute to the protection of the environment.

Technical data

Connections .......................................... 2 x serial

Chipset ................................................. MosChip

Slot type ................................................ PCI

Operating temperature ......................... 0 to +70 °C

Operating instructions

2 Port Serial PCI-Card Low Prole

Item no. 1648554

Intended use

This PCI multi-I/O card uses the latest PCI based Peripheral controller chipset from MosChip, enabling this

card to be installed on any PCI capable PC system. By using this card, end user can add two serial ports to

their PC system, allowing them to connect to their serial device.

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be

avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product

for purposes other than those described above, the product may be damaged. In addition, improper use can

cause hazards such as short circuiting, re, electric shock etc. Read the instructions carefully and keep them.

Make this product available to third parties only together with its operating instructions.

This product complies with the statutory national and European requirements. All company names and

Features

a) General

• Easy installation, automatically selects IRQ and I/O address

• Fully compliant with PCI Local Bus Specication Revision 2.3

• Supports PCI power management

• Supports PCI IRQ sharing feature, saves valuable resources for other add-on cards

• Supports multiple cards on one PC

• Supports Windows 2000, XP 32-/64-bit, Server 2003, Vista 32-/64-bit, or above, Linux kernel 2.6.14 or

above

b) Serial Port (RS-232) Interface

• Compatible with industrial standard 16C550 UART

• On-chip 256-byte depth FIFO in Transmit & Receive paths of each port

• Fast data rate up to 115.2K bits/sec on each port

• Supports hardware and software ow control

• Supports 5-, 6-, 7-, 8-, 9- bit serial format

• Supports Even, Odd, None, Space & Mark parity

• Supports 1 or 2 Stop bit operation

Delivery content

• PCI card

• 2 x low prole bracket

• Driver CD

• Manufacturer’s manual

• Operating instructions

Latest operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code

shown. Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of personal injury,

such as electric shock.

An exclamation mark in a triangle indicates important instructions in this operating manual that

absolutely have to be observed.

The arrow symbol indicates specic tips and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety information.

If you do not follow the safety instructions and information on proper handling in this

manual, we assume no liability for any resulting personal injury or damage to property.

Such cases will invalidate the warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing

material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,

moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it

from any accidental use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage

the product.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in

part, is prohibited. This publication represent the technical status at the time of printing.

Page is loading ...

Renkforce 2 ports Serial interface PCI Owner's manual

Brand: Renkforce

Model: 2 ports Serial interface PCI

Category: Interface cards/adapters

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce 2 ports Serial interface PCI Le manuel du propriétaire
Deutsch: Renkforce 2 ports Serial interface PCI Bedienungsanleitung
Nederlands: Renkforce 2 ports Serial interface PCI de handleiding

Renkforce 2 ports Serial interface PCI Owner's manual

Renkforce 2 ports Serial interface PCI Owner's manual

in other languages

Related papers

Other documents