FORS WE8566 User manual

Brand: FORS

Model: WE8566

Category: Washing machines

Type: User manual

User manual

Washing Ma-

chine

Benutzer-

information

Wasch-

maschine

WE 8566

CONTENTS

Safety information 2

Safety instructions 3

Product description 4

Control panel 5

Programmes 8

Consumption values 10

Options 11

Before first use 13

Daily use 13

Hints and tips 17

Care and cleaning 18

Troubleshooting 21

Technical information 23

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read

the supplied instructions. The manufacturer is not responsible

if an incorrect installation and use causes injuries and dam-

ages. Always keep the instructions with the appliance for fu-

ture reference.

Children and vulnerable people safety

Warning! Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the haz-

ards involved.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep all detergents away from children.

• Keep children and pets away from the appliance door when

it is open.

• If the appliance has a child safety device, we recommend

you activate it.

• Cleaning and user maintenance shall not be made by chil-

dren without supervision.

General Safety

• Before maintenance, deactivate the appliance and discon-

nect the mains plug from the mains socket.

• Do not change the specification of this appliance.

• Obey the maximum load volume of 8 kg (refer to the “Pro-

gramme chart” chapter).

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

• The operating water pressure (minimum and maximum)

must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)

• The ventilation openings in the base (if applicable) must not

be obstructed by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging and the transit

bolts.

• Keep the transit bolts. When you move

the appliance again you must block the

drum.

• Do not install or use a damaged appli-

ance.

•Do not install or use the appliance where

the temperature is less than 0 °C or

where it is exposed to the weather.

• Obey the installation instruction supplied

with the appliance.

• Make sure that the floor where you install

the appliance is flat, stable, heat resistant

and clean.

• Do not install the appliance where the ap-

pliance door can not be fully opened.

• Always be careful when you move the

appliance because it is heavy. Always

wear safety gloves.

• Make sure that there is air circulation be-

tween the appliance and the floor.

• Adjust the feet to have the necessary

space between the appliance and the

carpet.

Electrical connection

Warning! Risk of fire and electrical

shock.

• The appliance must be earthed.

• Make sure that the electrical information

on the rating plate agrees with the power

supply. If not, contact an electrician.

• Always use a correctly installed shock-

proof socket.

• Do not use multi-plug adapters and ex-

tension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the appliance power supply cable

need to be replaced, this must be carried

out by our Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

• Do not touch the mains cable or the

mains plug with wet hands.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Make sure not to cause damage to the

water hoses.

• The appliance is to be connected to the

water mains using the new supplied

hose-sets. Old hose sets must not be

reused.

• Before you connect the appliance to new

pipes or pipes not used for a long time,

let the water flow until it is clean.

• The first time you use the appliance,

make sure that there is no leakage.

Use

Warning! Risk of injury, electrical

shock, fire, burns or damage to the

appliance.

• Use this appliance in a household envi-

ronment.

• Do not change the specification of this

appliance.

• Obey the safety instructions on the deter-

gent packaging.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

• Do not touch the glass of the door while

a programme operates. The glass can be

hot.

• Make sure that you remove all metal ob-

jects from the laundry.

• Do not put a container to collect possible

water leakage under the appliance. Con-

tact the Service to ensure which acces-

sories can be used.

Care and Cleaning

Warning! Risk of injury or damage to

the appliance.

• Before maintenance, deactivate the ap-

pliance and disconnect the mains plug

from the mains socket.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

Disposal

Warning! Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent chil-

dren and pets to get closed in the appli-

ance.

PRODUCT DESCRIPTION

1 2 3

Worktop

Detergent dispenser

Control panel

Door handle

Rating plate

Drain pump filter

Feet for the appliance level

Child safety device

When you activate this device, you cannot

close the door. This prevents children or

pets to be closed in the drum. To activate

the device, turn it clockwise, until the

groove is horizontal. To deactivate the de-

vice, turn it counter-clockwise, until the

groove is vertical.

Fixing plate kit (4055171146)

Use this special accessory, when you install

the appliance on a plinth.

It prevents the movements of the appliance

when it operates.

Read carefully the instructions supplied with

this accessory.

You can buy it in all approved Service.

CONTROL PANEL

Temp.

Spin

Start/Pause

Delay

Start

Time

Save

Extra

Rinse

Stains/

Prewash

Wool/Silk

Cottons

Extra Silent

Synthetics

Easy Iron

Delicates

Duvet

Anti-Allergy

Spin/Drain

Rinse

Jeans

20 Min. - 3 kg

Super Eco

Refresh

Anticrease

Auto Off

1 2 3

45678910

Cottons

Eco

On/Off button (Auto Off)

Programme knob

Display

Start Pause button (Start/Pause - Dé-

part/Pause)

Delay start button (Zeitvorwahl - Dé-

part Différé)

Time saving button (Zeit Sparen -

Gain de Temps)

Extra rinse button (Extra Spülen -

Rinçage+)

Stain/Prewash button (Flecken/Ta-

ches - Vorw./Prélavage)

Spin reduction button (U./Min. - T/

min.)

Temperature button (Temperatur -

Température)

Display

A H

K J

C D E F GB

M L

The display shows:

The temperature of the set programme

Cold water

The spin speed of the set programme

No Spin symbol

Rinse Hold symbol

1) Only available for SPIN/DRAIN programme.

Prewash phase

Washing phase

Rinses phase

Spin phase

The phase symbols

• When a programme is set, all the symbols of the phases related to the pro-

gramme come on.

• When the programme starts, only the symbol of the phase in operation flashes.

• When the programme is completed, the symbol of the last phase is on.

The steam symbol comes on when you set a Steam programme.

The detergent overdosing symbol comes on at the end of the cycle

when the appliance detects too much detergent.

You cannot open the appliance door when the symbol is on.

You can open the door only when the symbol goes off.

If the programme is completed but the symbol stays on:

• The 'Rinse Hold' function is on.

• There is water in the drum.

The delay start symbol comes on when you set the delay start func-

tion.

The child safety lock symbol comes on when this device is activated.

• The programme time

When the programme starts, the programme time decreases with

steps of 1 minute.

•The delay start

When you press the delay start button, the display shows the delay

start time.

•Alarm codes

If the appliance has a malfunction, the display shows alarm codes.

Refer to 'Troubleshooting'.

• The display shows this message for some seconds when:

– You cannot set a function with the washing programme.

– You try to change the washing programme while it operates.

• When the programme is completed.

When the door is open - Refer to 'Loading the laundry' paragraph

• The maximum programme load

The symbols shows the maximum load for the set

programme.

• The weight of laundry

The symbol shows the weight of the laundry inside the

drum. When you load the laundry, the weight updates

by steps of 0.5 kg.

When the door is closed

•The symbol of detergent

• The percentage of the detergent quantity.

The symbols shows the quantity of detergent to use

for the laundry in the drum. When you press the Start/

Pause button, these symbols go off.

Graphic bars

The empty indicator bar appears only if the related function is availa-

ble for the set programme.

The indicator bar fills accordingly to the set functions.

If you make a wrong selection the message Err indicates that the selection is not possible.

The time save symbol comes on when you set one of the pro-

gramme duration.

• Shortened time

•Extra Quick

The extra rinse symbol comes on when this function is activated.

The value shows the total number of the rinses.

The indicator bar is fully filled when you set the maximum number of

rinses.

The Stain symbol comes on when you activate the function.

The Prewash symbol comes on when this function is activated.

The indicator bar is not fully filled when you set only one of the func-

tions.

The indicator bar is fully filled when you set the two functions.

PROGRAMMES

Programme

Temperature range

Type of load and soil

Maximum load, Maximum spin

Koch/Bunt - Blanc / Couleurs

Cottons

95°C - Cold

White cotton and coloured cotton. Normal soil and light soil.

8 kg, 1600 rpm

Extra Leise - Extra Silence

Extra Silent

95°C - Cold

White and coloured cotton. Normal soil and light soil.

8 kg, 1600 rpm

Pflegeleicht - Synthétiques

Synthetics

60°C - Cold

Synthetic or mixed fabric items. Normal soil and light soil.

2.5 kg, 1200 rpm

Leichtbügeln - Repassage Facile

Easy Iron

60°C - Cold

Synthetic fabric items. Normal soil and light soil.

4 kg, 1000 rpm

Feinwäsche - Délicats

Delicate

40°C - Cold

Delicate fabrics as acrylics, viscose, polyester items. Normal

soil and light soil.

4 kg, 1200 rpm

Wolle/Seide - Laine/Soie

Wool/Silk

40°C - Cold

Machine washable wool, hand washable wool and delicate

fabrics with «hand washing» care symbol.

2 kg, 1200 rpm

Daunen - Couette

Duvet

60° - 30°

Special programme for one synthetic blanket, duvet, bed-

spread and so on.

3 kg, 800 rpm

Anti-Allergie - Anti-Allergies

Anti allergy

60°

White cotton items. This programme removes micro-organ-

isms thanks to the washing by 60° C and adds one rinse. In

this way the wash is more effective. Put a special additive for

hygiene in the Stain compartment and set the Stain function.

8 kg, 1600 rpm

Schleudern/Pumpen - Essorage / Vi-

dange

To spin the laundry and to drain the water in the drum. All

fabrics.

8 kg, 1600 rpm

Spülen - Rinçage

Cold

To rinse and spin the laundry. All fabrics.

8 kg, 1600 rpm

Outdoor - Blousons

Outdoor

60°C - Cold

Waterproof, sports and outdoor items. Do not use any fabric

softener!

2.5 kg, 800 rpm

20 Min. - 3 kg

40° - 30°

Cotton and synthetic items with light soil or worn only one

time.

Programme

Temperature range

Type of load and soil

Maximum load, Maximum spin

Super Eco

Cold

Mixed fabrics (cotton and synthetic items).

max. 3 kg, 1200 rpm

Baumwolle Eco

60 °C - 40 °C

White cotton and colour-fast cotton. Normal soil.

8 kg, 1600 rpm

Steam programmes

Auffrischen - Rafraîchir

Steam - Refresh

Steam programme for cotton and synthetic

This cycle removes odours from the laundry.

1.5 kg

Glätten - Défroissage

Steam Dewrinkler

Steam programme for cotton and synthetic

This cycle helps to dewrinkle the laundry.

1.5 kg

1) The wash and spin phase is soft to prevent the creases of the laundry. The appliance adds some rinses.

2) The default phase of the spin speed is related to cotton items. Set the spin speed. Make sure that it agrees with

the laundry.

3) Set this programme to decrease the time and the consumption of energy and water.

4) Standard programmes for the Energy Label consumption values

According to regulation 1061/2010, these programmes are respectively the «standard 60 °C cotton programme»

and the «standard 40 °C cotton programme». They are the most efficient programmes in terms of combined

energy and water consumption for washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the selected pro-

gramme.

Programme options compatibility

Programme

Flecken-Taches

Vorwäsche-Prélavage

Extra Spülen - Rinçage+

Zeit Sparen - Gain de Temps

Zeitvorvahl - Départ Différé

Koch/Bunt - Blanc /

Couleurs

■ ■ ■ ■ ■ ■

Extra Leise - Extra Si-

lence

■ ■ ■ ■

Pflegeleicht - Synthé-

tiques

■ ■ ■ ■ ■ ■

Leichtbügeln - Repas-

sage Facile

■ ■ ■ ■ ■

Feinwäsche - Délicats ■ ■ ■ ■ ■ ■

Wolle/Seide

- Laine/Soie

■

Daunen - Couette ■ ■

Programme

Flecken-Taches

Vorwäsche-Prélavage

Extra Spülen - Rinçage+

Zeit Sparen - Gain de Temps

Zeitvorvahl - Départ Différé

Anti-Allergie - Anti-Al-

lergies

■ ■ ■ ■ ■

Schleudern/Pumpen -

Essorage / Vidange

■ ■

■

Spülen - Rinçage ■ ■ ■ ■

Outdoor - Blousons ■ ■ ■ ■ ■

20 Min. - 3 kg ■ ■

Super Eco ■ ■ ■ ■

Baumwolle Eco

■ ■ ■ ■ ■ ■

1) If you set No Spin option the only drain phase is available.

Woolmark Certificate

The wool wash of this machine has been tested

and approved by The Woolmark Company for

the washing of wool containing garments la-

beled as «hand wash» provided that the gar-

ments are washed according to the instructions

on the garment label and those issued by the

manufacturer of this washing machine. M1144

In UK, Eire, Hong Kong and India the Woolmark

symbol is a certification trademark.

CONSUMPTION VALUES

At programme start the display shows the duration programme for the maximum

load capacity.

During the washing phase the programme duration is automatically calculated and

can greatly be reduced if the laundry load is lower than the maximum load capacity

(e.g. Cotton 60°C, maximum load capacity 8 kg, the programme duration exceeds 2

hours; real load 1 kg, the programme duration don’t reach 1 hour).

When the appliance is calculating the real programme duration a dot blinks in the

display.

The data of this table are approximate. Different causes can change the data: the

quantity and type of laundry, the water and ambient temperature.

Programmes Load

(Kg)

Energy con-

sumption

(kWh)

Water con-

sumption (li-

tre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Koch/Bunt -

Blanc / Couleurs

60 °C

8 1.50 66 179 43

Koch/Bunt -

Blanc / Couleurs

40 °C

8 0.90 66 175 43

Pflegeleicht -

Synthétiques 40

°C

4 0.60 48 110 35

Feinwäsche -

Délicats 40 °C

4 0.70 58 91 35

Wolle - Laine 30

°C

2 0.35 57 56 30

Standard cotton programmes

Standard 60 °C

cotton

8 0.83

220 43

Standard 60 °C

cotton

4 0.54

184 43

Standard 40 °C

cotton

4 0.43

179 43

Off Mode (W) Left On Mode (W)

0.05 0.05

The information given in the chart above are in compliance with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC.

1) At the end of spin phase.

OPTIONS

Temperature (Temperatur -

Température)

Set this option to change the default tem-

perature.

Indicator

= cold water.

The indicator of the set temperature comes

on.

Spin (U./Min. - T/min.)

With this option you can decrease the de-

fault spin speed.

The display shows the indicator of the set

speed.

Additional spin options:

No Spin

• Set this option to remove all spin phases.

• Set it for very delicate fabrics.

• The rinse phase uses more water for

some washing programmes.

•

The display shows the indicator

Rinse Hold

• Set this option to prevent the laundry

creases.

• The washing programme stops with the

water in the drum. The drum turns regu-

larly to prevent the laundry creases.

• The door stays locked. You must drain

the water to unlock the door.

•

The display shows the indicator

To drain the water refer to ‘At the end

of the programme’.

Stain-Prewash (Flecken/Taches

- Vorwäsche/Prélavage)

Set this option to add the stain and/or a

prewash phase to a programme.

Press this button again and again to acti-

vate one or two options. The related indica-

tor and the indicator bar comes on in the

display.

STAIN

• Use this function for laundry with hard

stains to remove.

When you set this function, put the stain

remover into compartment

. This

function increases the programme dura-

tion.

This function is not available with a

temperature lower than 40° C.

PREWASH

• Use this function to add a prewash

phase before the washing phase. Use

this option for heavy soil. This function in-

creases the programme duration.

Extra Rinse (Extra Spülen -

Rinçage+)

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to deter-

gents and in areas where the water is soft.

The related indicator comes on.

Time save (Zeit Sparen - Gain

de Temps)

With this option you can decrease the pro-

gramme duration.

• Press this button one time to set 'Short-

ened duration' for items with daily soil.

• Press this button two times to set 'Extra

Quick' for items with almost no soil.

Some programmes accept only one of

the two functions.

Delay Start (Zeitvorvahl - Départ

Différé)

With this option you can delay the start of a

programme from 30 minutes to 20 hours.

The display shows the related indicator.

Child Lock

With this option you can prevent that the

children play with the control panel.

• To activate/deactivate this option,

press Temperatur - Température and U./

Min. - T/min. at the same time until the

indicator

comes on/goes off.

You can activate this option:

• After you press Start/Pause - Départ/

Pause, the options and the programme

knob are locked.

• Before you press Start/Pause - Départ/

Pause: the appliance cannot start.

Permanent extra rinse

With this option you can permanently have

an extra rinse when you set a new pro-

gramme.

• To activate/deactivate this option

press Zeit Sparen - Gain de Temps and

Zeitvorvahl - Départ Différé at the same

time until the indicator Extra Spülen - Rin-

çage+ comes on/goes off.

Acoustic signals

The acoustic signals operate when:

• You activate the appliance.

• You deactivate the appliance.

• You press the buttons.

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic sig-

nals, press Flecken/Taches - Vorwäsche/

Prélavage and Extra Spülen - Rinçage+ at

the same time for 6 seconds.

If you deactivate the acoustic signals,

they continue operate when the appli-

ance has a malfunction.

BEFORE FIRST USE

1. Put 2 litre of water in the detergent

compartment for washing phase. This

activates the drain system.

Put a small quantity of detergent in the

compartment for washing phase.

3. Set and start a programme for cotton

at the highest temperature without

laundry. This removes all possible dirt

from the drum and the tub.

DAILY USE

1. Open the water tap.

2. Connect the mains plug to the mains

socket.

For a correct operation of the weight sen-

sor, activate the appliance and set the

programme BEFORE you put the laundry

in the drum.

Activating the appliance

Press Auto Off to activate or deactivate the

appliance. A tune sounds when the appli-

ance is activated.

Setting a programme

1. Turn the programme knob and set the

programme:

• The related programme indicator

comes on.

• The indicator of Start/Pause - Dé-

part/Pause flashes.

• The display shows:

– the default temperature

– the spin speed

– the indicators of the programme

phases

– the programme duration.

If necessary, change the temperature,

the spin speed, the cycle duration, or

add available options. When you acti-

vate an option, the indicator of the set

option comes on.

If you set something incorrect, the dis-

play shows the message Err.

Loading the laundry

1. Open the appliance door.

The display (J) shows the maximum

load for the programme (MAX) and the

weight of the laundry (KG).

Put the laundry in the drum, one item at

time. Shake the items before you put

them in the drum.

4. On the display the weight of the laundry

updates by steps of kg 0.5. The weight

is indicative and changes with the type

of the laundry.

If you put in the drum more laundry

than the maximum load, the symbols

MAX and the value 0.0 start to flash.

You can wash your laundry but the wa-

ter and energy consumption increase.

To have the best consumption and

washing performance remove some

items until the symbols stop to flash.

The overload indication is available only

for programmes with a maximum load

lower than the appliance maximum

load.

5. Close the door. The value 0.0 near the

symbol % on the display shows the

quantity of the detergent to use.

This data is indicative and refers to the

detergent quantity for a maximum load

that the manufacturer recommends.

Make sure that no laundry stays between

the seal and the door. There is a risk of wa-

ter leakage or damage to the laundry.

Filling the detergent and additives

The detergent compartment for the prewash phase and the soak programme.

Add the detergent for prewash and soak before the start of the programme.

The detergent compartment for the washing phase.

If you use a liquid detergent, put it immediately before you start the programme.

Liquid additives compartment (fabric conditioner, starch).

Put the product in the compartment before you start the programme.

This is the maximum level for the quantity of liquid additives.

The compartment for the stain remover.

Put the product in the compartment and set the stain function before you start

the programme.

Flap for powder or liquid detergent

Turn it (up or down) in the correct position to use powder or liquid detergent.

Always obey the instructions that you find on the packaging of the detergent products.

Check the position of the flap

Pull out the detergent dispenser until it

stops.

Press the lever down to remove the

dispenser.

To use powder detergent, turn the flap

up.

4. To use liquid detergent, turn the flap

down.

With the flap in the position DOWN:

– Do not use gelatinous or thick liquid

detergents.

– Do not put more liquid detergent

than the limit showed in the flap.

– Do not set the prewash phase.

– Do not set the delay start function.

5. Measure out the detergent and the

fabric conditioner.

Carefully close the detergent dispens-

er. Make sure that the flap does not

cause a blockage when you close the

drawer.

Starting a programme without

delay start

Press Start/Pause - Départ/Pause:

• The indicator Start/Pause - Départ/Pause

stops to flash and stays on.

•

The indicator

starts to flash on the

display.

• The programme starts, the door is locked

and the display shows the indicator

• The drain pump can operate for a short

time when the appliance fills water.

After approximately 15 minutes from

the start of the programme:

• The appliance adjusts automatically

the programme duration agree with

the laundry load.

• The display shows the new value.

Starting a programme with

delay start

• Press Zeitvorvahl - Départ Différé again

and again until the display shows the de-

lay you want to set. The related indicator

comes on the display.

• Press Start/Pause - Départ/Pause:

– The appliance starts the countdown.

– When the countdown is completed,

the programme starts automatically.

You can cancel or change the set of

the delay start before you press Start/

Pause - Départ/Pause .

To cancel the delay start:

1. Press Start/Pause - Départ/Pause to

set the appliance to pause.

Press Zeitvorvahl - Départ Différé until

the display shows

’.

Press Start/Pause - Départ/Pause

again to start the programme immedi-

ately.

Interrupting a programme and

changing the options

You can change only some options before

they operate.

Press Start/Pause - Départ/Pause. The

indicator flashes.

Change the options.

Press Start/Pause - Départ/Pause

again. The programme continues.

Cancelling a programme

Press Auto Off for some seconds to

cancel the programme and to deacti-

vate the appliance.

2. Press the same button again to activate

the appliance. Now, you can set a new

washing programme.

The appliance does not drain the wa-

ter.

Opening the door

While a programme or the delay start oper-

ates, the appliance door is locked and the

display shows the indicator

Caution! If the temperature and level

of the water in the drum are too high,

you cannot open the door.

Open the appliance door when the

delay start operates:

1. Press Start/Pause - Départ/Pause to

pause the appliance.

Wait until the door lock indicator

goes off.

Open the door.

4. Close the door and press Start/Pause -

Départ/Pause again. The delay start

continues to operate.

Open the appliance door when the

programme operates:

Press Auto Off for some seconds to

deactivate the appliance.

Wait for some minutes and then open

carefully the appliance door.

Close the appliance door.

Set the programme again.

At the end of the programme

• The appliance stops automatically.

• The acoustic signal operates (if it is acti-

vated).

•

In the display a

comes on.

• The indicator Start/Pause - Départ/Pause

goes off.

•

The door lock indicator

goes off.

• Remove the laundry from the appliance.

Make sure that the drum is empty.

• Keep the door ajar, to prevent the mildew

and odours.

• Close the water tap.

• Press Auto Off for some seconds to de-

activate the appliance.

The washing programme is completed,

but there is water in the drum:

– The drum turns regularly to prevent the

creases in the laundry.

–

The door lock indicator

is on. The

door stays locked.

– You must drain the water to open the

door.

To drain the water:

1. If necessary, decrease the spin

speed.

Press Start/Pause - Départ/Pause.

The appliance drains the water and

spins.

When the programme is completed

and the door lock indicator

goes

off, you can open the door.

4. Press Auto Off for some seconds to

deactivate the appliance.

The appliance drains and spins auto-

matically after approximately 18 hours

(except for Wool programme).

AUTO OFF option

The AUTO OFF option automatically deacti-

vates the appliance to decrease the energy

consumption when:

• You do not use the appliance for 5 mi-

nutes before you press the button Start/

Pause - Départ/Pause.

Press the button Auto Off to activate the

appliance again.

• After 5 minutes from the end of the

washing programme

Press the button Auto Off to activate the

appliance again.

The display shows the end of the last set

programme.

Turn the programme knob to set a new

cycle.

HINTS AND TIPS

The laundry load

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are on

the laundry care labels.

• Do not wash together white and coloured

items.

• Some coloured items can discolour with

the first wash. We recommend that you

wash them separately for the first times.

• Button up pillowcases, close zippers,

hooks and poppers. Tie up belts.

• Empty the pockets and unfold the items.

• Turn inside out multilayered fabrics, wool

and items with painted illustrations.

• Remove hard stains.

• Wash with a special detergent heavy soil

stains.

• Be careful with the curtains. Remove the

hooks or put the curtains in a washing

bag or pillowcase.

•Do not wash in the appliance :

– Laundry without hems or with cuts

– Underwired bras.

– Use a washing bag to wash small

items.

• A very small load can cause balance

problems with the spin phase. If this oc-

curs, adjust manually the items in the tub

and start the spin phase again.

Stubborn stains

For some stains, water and detergent is not

sufficient.

We recommend that you remove these

stains before you put the items in the appli-

ance.

Special stain removers are available. Use

the special stain remover that is applicable

to the type of stain and fabric.

Detergents and additives

• Only use detergents and additives spe-

cially made for washing machines.

• Do not mix different types of detergents.

• To help the environment, do not use

more than the correct quantity of deter-

gent.

• Obey the instructions that you find on the

on packaging of these products.

• Use the correct products for the type and

colour of the fabric, the programme tem-

perature and the level of soil.

• If your appliance has not the detergent

dispenser with the flap device, add the

liquid detergents with a dosing ball.

Ecological hints

• Set a programme without the prewash

phase to wash laundry with normal soil.

• Always start a washing programme with

the maximum load of laundry.

• If necessary, use a stain remover when

you set a programme with a low temper-

ature.

• To use the correct quantity of the deter-

gent, check the water hardness of your

domestic system

Water hardness

If the water hardness in your area is high or

moderate, we recommend that you use a

water softener for washing machines. In

areas where the water hardness is soft it is

not necessary to use a water softener.

To know the water hardness in your area,

contact your local water authority.

Use the correct quantity of the water soft-

ener. Obey the instructions that you find on

the packaging of the product.

CARE AND CLEANING

Warning!

Before maintenance, disconnect the appli-

ance from the mains supply.

External cleaning

Clean the appliance only with soap and

warm water. Fully dry all the surfaces.

Caution! Do not use alcohol, solvents

or chemical products.

Descaling

If the water hardness in your area is high or

moderate, we recommend that you use a

water softener for washing machines.

Regularly examine the drum to prevent

limescale and rust particles.

To remove rust particles use only special

products for washing machine. Do this sep-

arately from the laundry wash.

Always obey the instructions that you

find on the packaging of the product.

Maintenance wash

With the low temperature programmes it is

possible that some detergent stays in the

drum. Make regularly a maintenance wash.

To do this:

• Remove the laundry from the drum.

• Set the cotton programme with the high-

est temperature with a small quantity of

detergent.

Door seal

Regularly examine the seal and remove all

objects from the inner part.

Cleaning the detergent dispenser

3. 4.

Cleaning the drain filter

Warning! Do not clean the drain filter if

the water in the appliance is hot.

3. 4.

7. 8.

Cleaning the inlet hose and the valve filter

1. 2.

Page is loading ...

FORS WE8566 User manual

Brand: FORS

Model: WE8566

Category: Washing machines

Type: User manual

Download PDF

report

in other languages

Deutsch: FORS WE8566 Benutzerhandbuch

FORS WE8566 User manual

FORS WE8566 User manual

in other languages

Related papers

Other documents