Dorel Home 4104419 User manual

DO NOT RETURN TO THE STORE !

Visit www.dhpfurniture.com/eng/support-home

or call Toll-Free 1-800-267-1739

4104019

B34410401900 - 10125-M

Date of Purchase

Rockstar Metal Bunk Bed

F.C. - 2016/9/5

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Twin Over Full

Black

Weight Limit:

200 Lb / 91 Kg For Upper Bed

450Lb / 204Kg For Lower Bed

TM

Contact Us!

cs@dhpfurniture.com

DHP

410E, First Street South, Wright City, MO 63390, USA

Attention: Consumer Service.

Read Before Beginning Assembly

1-800-267-1739

Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)

Warranty Information

2

B34410401900

Caution

DHP warrants this product to be free from defects in material and workmanship and

agrees to remedy any such defect. This warranty covers one year from the date of

original purchase. This is solely limited to the repair or replacement of defective

parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly assembled,

subjected to misuse or abuse or which has been altered or repaired in any way.

Liability for consequential damages is excluded to the extent exclusion is permitted

by law. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

To obtain warranty service, purchaser must present original bill of sale. Components

repaired or replaced are warranted through the remainder of the original warranty

period only. The defective components will be repaired or replaced without charge,

subject to the terms and conditions described above.

Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and

Canada.

 Call our toll free number if you need assistance.

 Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and product.

 Recommended # of people needed for assembly: 2 (however it is always better

to have an extra hand). Estimated assembly time is 1.5 hours.

 Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

 Read each step carefully. It is very important that each step of instruction is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

 This product is designed for home use and not intended for commercial use.

 This product contains small components. Please ensure that they are kept away

from small children.

 Do not use power tools to assemble your furniture. Power tools may strip or

damage the parts.

 You will need a phillips headed screwdriver to assemble this product.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Page is loading ...

4

Parts

B34410401900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

A

Post 1

T941940

X 1

B C

D

E

X

M

X1

T

Z

J

Post 2

T941950

X 1

Post 3

T941960

X 1

Post 4

T941970

X 1

Side Rail

T922140

X 2

End Rail

T910850

X 2

Ladder

T922390

X 2

Guard Rail

T941980

X 2

End Guard Rail 1

T941990

X 1

End Guard Rail 2

T942000

X 1

Middle Rail

T910150

X 1

P

O

W

Q

Y

Upper Slats

T919610

X 22

Lower Slats

T919600

X 22

Slat Spacer 01

T919480

X 66

Slat Spacer 02

T919490

X 63

Plastic Plag

T392590

X 88

A

B

D

E

M

X1

O

T

X

Y

C

J

Z

W

Q

P

5

Hardware Pack

B34410401900

Hardware Pack #: T4104019-00

Hardware Note:

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step

instructions.

6 7 8

4 5

3

2

1

1/4" X 1 3/4"

X 4

1/4" X 1 3/16"

X 8

5/16" X 3/4"

X 8

1/4" X 3/4"

X 16

4.2 X 10mm

X 2

1/4"

X 8

4mm

X 1

Wrench

X 1

A

B

6

B34410401900

Step

1

1.1 Slide (A) & (B) into (M), then fasten

with BOLTS 4.

1.2 Attach (T) to (A) & (B) with BOLTS 4.

X 6

A

B

T

M

A

T

4

1.1

1.2

4

C

D

7

B34410401900

Step

2

2.1 Slide (C) & (D) into (X1), then fasten

with BOLTS 4.

2.2 Attach (T) to (C) & (D) with BOLTS 4.

X 6

C

D

T

X1

C

X1

C

T

4

2.1

2.2

4

E

8

B34410401900

Step

3

Attach (E) X 2 to (X1) & (M) with BOLT 4

and BOLTS 1.

X 4

C

A

B

D

E

X1

1

X 4

4

1

4

X1

M

F

9

B34410401900

Step

4

Attach (J) X 2 to (A,B,C,D) with BOLT 3.

X 8

A

B

C

D

J

D

J

3

Wide side of the slot should

be facing up !

G

K

10

B34410401900

Step

5

5.1 Attach (Z) X 2 to (M) & (T) & (X1) with

BOLTS 2 and NUTS 6.

5.2 Attach (X) to (T) X 2 with SCREWS 5.

X 8

2

6

M

X1

T

X

Z

X 2

5

Z

M

2

6

T

X

5

5.1

5.2

11

B34410401900

Step

6

Slide (O) into the slots on (E), Lock (O) into

place with (Y).

Slide (P) into the slots on (J), Lock (P) into

place with (Y).

E

J

P

O

2

1

2

3

1

E

O

Y

12

B34410401900

Step

7

7.1 Press (W) onto (O) & (P) approximately

in the middle, as illustrated.

7.2 Press (Q) onto (W) alternating left and

right.

P

O

W

O

Q

W

7.1

7.2

1

8

"

1

8

"

1

8

"

13

Helpful Hints

B34410401900

 Move your new furniture carefully, with two

people lifting and carrying the unit to its new

location.

 Your DHP furniture can be disassembled and

reassembled to move.

 Some parts have been pre-assembled for this

item. They are illustrated on this page and available

for replacement.

Helpful Hints

Weight Limit:

200 Lb / 91 Kg For Upper Bed

450Lb / 204Kg For Lower Bed

End Cap

T919620

X 4

14

B34410401900

WARNINGS for Bunk Bed

 Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.

 Always use the recommended size mattresses or mattress supports, or both, to help prevent the likelihood of entrapment or falls.

 Use only a twin mattress which is 74"-75" long and 37 1/2"-38 1/2" wide on upper bunk and a full mattress which is 74"-75" long and 53 1/2"-54 1/2" wide on lower bunk.

 Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.

 Do not allow children under 6 years of age to use the upper bunk.

 Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage, and that all connectors are tight.

 Do not allow horseplay on or under the bed and prohibit jumping on the bed.

 Prohibit more than one person on upper bunk.

 Always use the ladder for entering and leaving the upper bunk.

 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

 Replacements parts, including additional guardrails, may be obtained from DHP.

 Use of a night light may provide added safety precaution for a child using the upper bunk.

 Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed

against the wall to prevent entrapment between the bed and wall.

 The use of water or sleep flotation mattresses is prohibited.

 Do not use risers under this product.

 STRANGULATION HAZARD-Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts

and jump ropes.

 Keep these instructions for future reference.

Page is loading ...