Muller's Smart Carts ULGC Installation guide

Brand
Muller's Smart Carts
Model
ULGC
Type
Installation guide
ULTIMATE GARDENER BY SMART CARTS: INSTRUCTIONS
Step 1: Locate the different components. Get the right tools.
Step 2: Using the 3/4” bolts and acorn nuts create the
Floor Assembly by attaching the Floor Panel (the
biggest plastic sheet) to the two side supports. The
textured side of the Floor Panel should be facing up
and the smooth side facing toward the ground. Make
sure that the holes of the side supports match the
holes of the Floor Panel (there is a left and a right side
support) then secure only the two front holes to the
Floor Panel at this step. Make sure that the bolt head
is against the textured side of the Floor Panel making
the nut to be underneath the Panel (against the
smooth side of the sheet).
Step 3: Connect the aluminum Back Support to the Floor
Assembly. The Back Support goes over the Side Supports
making the Side Supports to be “sandwiched” between
the plastic Floor Panel and the Back Support (See
picture). Secure together the plastic Floor Panel, the
Side Support and the Back Support using the 3/4” bolts
and acorn nuts. The ¾” bolts are just long enough and
you may have to apply pressure on the assembly in order
to get the acorn nut to start engaging.
**Do not fully tighten the hardware.**
Step 4: Connect the two Upright Supports to
the Back Support using the 1/2” bolts and
acorn nuts. The 1/2” bolts are the shortest
bolts that you have. Do not connect the Side
Supports to the Upright Supports at this
point. The remaining holes will be used to
secure the plastic Side Panels (see next step).
.
Tools: Phillips
head screw
driver. Socket
or wrench set
(7/16). Pliers
to bend the
cotter pins.
Axle
Back Panel
Floor Panel
Side Panel (2)
Side Support (2)
Back Support
Leg
Handle
Wheel (2)
Upright
Support (2)
Front
The Back is in the direction of
the 2 side by side holes
located on the Floor Panel.
Back Support
Side Support
Back of the
Floor Panel
Make sure that the
bolt head sits against
the textured side of
the Floor Panel.
Front 2 Holes
**Do not fully tighten the hardware.**
**MAKE SURE TO READ
EACH STEP IN FULL AND
LOOK AT THE PICTURES
BEFORE STARTING TO
ASSEMBLE.**
**Do not fully tighten the hardware**.
Axle Bracket (2)
Spacers (2)
Cotter Pin (2)
Wing Nut (2)
3/4” Bolt (20)
Acorn Nuts (28)
1/2” Bolt (2)
Washers (8)
1 3/4” Bolt (8)
Floor Panel
Step 7: Slide the Leg over the mid section
of the cart as shown. The Leg is the
component having the two bolts already
attached to it. Secure the bottom portion
by sliding the 1 3/4” Bolts and washers
through the Side Panel, Side Support and
Leg. Secure using the Acorn Nuts. Secure
the top section using the 1 3/4” bolts,
washers and acorn nuts. Make sure that the
bolt head and washers are installed inside
the cart and the acorn nuts outside the cart
Step 9: **FULLY TIGHTEN THE HARDWARE
AFTER ALL OF THE BOLTS AND NUTS ARE IN
PLACE AND BEFORE GOING TO STEP 10.**
Step 10: Install the two axle
brackets to the frame using
the 3/4” bolts and acorn nuts.
Smart Carts Enterprises LLC - www.smartcarts.com - (800) 366-6026
Help is available. Please
call 800.366.6026
Step 5: Install the two Side Panels to the Upright and Side Supports using the 3/4” bolts and acorn nuts. Note
that the sticker and the textured side of the plastic is facing out. You will have to install 3 bolts per side to
secure the bottom part of the Side Panel (skipping the second hole from the front) and one more at the top of
the side panel to secure the Side Support to the Uprights.
Step 6: Install the Back Panel by sliding it
between the Uprights and the back of the
Side Panels making sure that the notched
corners are facing down and the textured
side of the plastic is facing out. The
notched corners slide over the bottom
bolts in order for the Back Panel to be
flush with the Side Panels. Secure using
the ¾ Bolts and Wing Nuts
ULTIMATE GARDENER BY SMART CARTS: INSTRUCTIONS
Skip the second hole from the front.
This hole will be used to secure the
Leg at Step 7.
A 1/4” gap is
expected
between the
Uprights and
the back of
the Side
Panels.
Step 8: Install the
Handle to the cart by
sliding the 1 3/4”
bolts and washers
through the Side
Panel and Handle.
Secure using the
acorn nut. Make sure
that the bolt head
and washers are
installed inside the
cart and the acorn
nuts outside the cart.
Step 11: Slide the axle
through the brackets, slide
the spacers on the axle and
mount the wheels to the
axle.
Step 12: Slide the Cotter
Pin into the axle hole. The
cotter pins need to be
opened and bent in order
to stay secured.
NOTE: The
Ultimate
Gardener is not
made for human
transport.
Do not fully tighten the hardware.
  • Page 1 1
  • Page 2 2

Muller's Smart Carts ULGC Installation guide

Brand
Muller's Smart Carts
Model
ULGC
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents