GE GFDN245GL User manual

Type
User manual

This manual is also suitable for

For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Dimensions and Installation Information (in inches)
Exhaust Options: 3-way via rear, left, and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 15-20 amp circuit breaker
or a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information, see
installation instructions packed with your dryer.
27
1-5/8
40-1/2
33
5-1/2
3-3/4
Gas Dryer Rating
120V
60Hz, 6A
Specification Revised 10/10
360484
GFDN240GL/GFDN245GL
GE
®
7.0 cu. ft. stainless steel capacity frontload dryer
For answers to your Monogram,
®
GE Profile
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Special Installation Requirements:
Stacked Installation:
Kit for stacking dryer over washer is not included with the dryer.
Order GEFLSTACK.
Alcove or Closet Installation:
•Ifyourdryerisapprovedforinstallationinanalcoveorcloset,itwillbe
stated on a label on the dryer back.
•ThedryerMUSTbeexhaustedtotheoutside.
•Minimumclearancesbetweendryercabinetandadjacentwallsorother
surfaces are: 0" either side, 3" front and rear
•Minimumverticalspacefromfloortooverheadcabinets,ceilings,etc.is52".
•Closetdoorsmustbelouveredorotherwiseventilatedandmustcontaina
minimumof60sq.in.ofopenareaequallydistributed.Ifthisclosetcontains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
•Nootherfuel-burningapplianceshallbeinstalledinthesameclosetwith
a gas dryer.
Bathroom or Bedroom Installation:
•ThedryerMUSTbeexhaustedtotheoutdoors.
•Theinstallationmustconformwiththelocalcodes,orintheabsenceof
local codes, with the National Electric Code and National Fuel Gas Code,
ANSIZ223forgasdryers.
Minimum Clearance other than Alcove or Closet Installations:
•Minimumclearancestocombustiblesurfaces0"bothsides,3"rear.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
Stacked Dimensions (in inches)
Specification Revised 10/10
360484
GFDN240GL/GFDN245GL
GE
®
7.0 cu. ft. stainless steel capacity frontload dryer
81
Dryer Exhausting Information Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4” diameter
allrigidmetalexhaustduct.Ifrigidmetalductcannotbeused,thenUL-listedflexible
metal(semi-rigid)ductingcanbeused(KitWX08X10077).Inspecialinstallations,itmay
benecessarytoconnectthedryertothehouseventusingaflexiblemetal(foil-type)duct.
AUL-listedflexiblemetal(foil-type)ductmaybeusedONLYininstallationswhererigid
metalorflexiblemetal(semi-rigid)ductingcannotbeusedANDwherea4”diametercan
be maintained throughout the entire length of the transition duct. Please see installation
instructionpackedwithyourdryerforcompleteinstructionswhenusingflexiblemetal(foil
type) ducting.
Exhaust Length Calculation:
1. Determinethenumberof90°turnsneededforyourinstallation.Ifyouexhausttothe
side or bottom of dryer, add one turn.
2. Themaximumlengthof4’rigid(aluminumorgalvanized)ductwhichcanbetoleratedis
shown in the table.
A turn of 4 or less may be ignored. Two 4 turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 9elbow.
Dryers mustbeexhaustedtotheoutside.
Caution: Forpersonalsafetydonotterminateexhaustintoachimney,underanyenclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazardormoisturecouldcausedamage.Neverterminatetheexhaustintoacommonduct
orplenumwithakitchenexhaust,sincethecombinationoflintandgreasecouldcreatea
fire hazard.
Exhaustductsshouldbeterminatedinadamperedwallcaptopreventbackdrafts,bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
Best performance
Domestic
dryer models
Maximum length of 4"
dia. rigid metal duct
Number
of
90°
turns
Exhaust hood type
A
4"
opening
B
2-1/2"
opening
7.0, 6.0 and 5.8 cu. ft.
capacity models
all gas dryers
0
1
2
3
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
45 ft.
35 ft.
25 ft.
A
4
B
2-1/ 2
A
Specification Revised 10/10
360484
GFDN240GL/GFDN245GL
GE
®
7.0 cu. ft. stainless steel capacity frontload dryer
Specification Revised 10/10
360484
GFDN240EL_245EL
Features and Benefits
• SensorDryPlus™-Innovativemoisture-sensingtechnologyhelpsmaintainquality
• eDryoption-Energy-savingoptionreducesdrytemperaturesonselectcycles
without sacrificing performance
• ActiveWearcycle-Specificsettingstotakespecialcareofclothingwornforactive
sportsexercise
• MyCycles-Customcyclethatcanbesetforspecificorfrequentneeds
• SpeedDry-Quicklydriesitemsandsmallloadsforfamiliesonthego
• 1-24-hourDelayStart-Setthedryertobegincycleswheneveritsconvenientforyou
• Upto90ft.ventingcapability-Haslongequivalentductingperformanceformore
flexibleinstallation
• Interiordryerlight-Convenientinteriorlighthelpsyoueasilyseeclothes
• ADACompliant
• ModelGFDN245GLMS–Metallicsilver
• ModelGFDN240GLWW–Whiteonwhite
• ModelGFDN245GLMV–VermillionRed
GFDN240GL/GFDN245GL
GE
®
7.0 cu. ft. stainless steel capacity frontload dryer
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

GE GFDN245GL User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI