King Clippo K 074 User manual

Model No: K 074 Clippo

Saç Kesme Makinesi / Hair Cutting Machine

Kullanma Kılavuzu / Instruction Manual

K 074

Clippo

Saç Kesme Makinesi

Hair Cutting Machine

Saç Kesme Makinesi /

Hair Cutting Machine

Kullanma Kılavuzu

MAIN PARTS

Mains Cable

On/Off Switch

Blade Lever

Top Blade

Bottom Blade

A.

B

C.

D.

E.

IMPORTANT

1. Please read these instructions carefully before using your clippers for the first time.

Please keep these instructions in a safe place for future reference.

2. The clippers are suitable for use on a mains supply voltage in the range 220 to 240V

and are suitable for home use only.

3. Before using for the first time ensure all packaging is removed and disposed of

correctly. Do not use any attachments not supplied with this clipper.

4. Regular care and cleaning is essential to maintain your Clipper Set in peak working

condition.

5. Before use, make sure the blades are aligned and securely attached to the main body.

6. Always unplug the clippers after use and never leave unattended when plugged in.

7. DO NOT use the clippers in a bathroom or near sinks or other vessels containing

water.

8. DO NOT wrap the mains cable around the clippers for storage; this may lead to cable

damage and cause early failure.

9. DO NOT use the clippers for any purpose other than clipping human hair.

10. DO NOT place appliance on any surface while it is operating.

11. DO NOT use on sensitive or damaged skin.

12. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience or knowledge, unless they

have been given instruction concerning use of the appliance by a person responsible for

their safety.

ADJUSTABLE LEVER

The lever is conveniently located near your thumb (if you’re right handed) so it can easily

be adjusted while the clipper is in your hand. It adds versatility to your clipper by allowing

you to gradually change the closeness of your cut without using an attachment comb.

When the lever is in the uppermost position, the blades will give you the closest cut and

leave the hair very short. Pushing the lever downward gradually increases the cutting

length.

GENERAL DESCRIPTION

Your Grooming Solutions Clipper comes complete with 4 attachment combs, Comb,

Scissors, Oil and Brush.

The combs leave hair at approximately the following lengths: No 1 Attachment comb

1/8” (0.3cm)

No.2 Attachment comb ¼” (0.6cm),No.3 Attachment comb 3/8” (0.9cm)

No.4 Attachment comb ½” (1.3cm)

OPERATING INSTRUCTIONS

Guide for cutting hair at home

Never use the product to cut wet hair. It is designed to work in dry conditions only.

During use your clippers will become warm. To prevent overheating, only use

continuously for a maximum of 30 minutes at a time and allow to cool for 10 minutes

between cuts.

Before you begin:

1. Make sure that your Grooming Solutions Clipper is clean, properly oiled and in perfect

working condition.

2. Place a towel around the neck of the person to prevent hair from falling down inside

the collar.

3. Position the person whose hair is to be cut on a chair so that his/her head is at your

eye level.

4. Comb the hair to remove all tangles; hold the clipper in a relaxed comfortable grip.

This will help you to maintain an accurate cutting control.

Cutting hair with the attachment combs

(For medium to long styles)

1. To attach combs, hold with teeth facing up and snap comb attachment firmly to the

bottom of the clipper blade.

2. At first cut a small amount of hair until you become accustomed to the length that each

attachment comb leaves the hair.

3. Try the longest attachment comb on the clipper first, and then use a shorter one if

desired.

4. Never push or force the clipper through the hair at a fast rate. The clipper works most

efficiently when it works at it’s own speed.

5. Start by combing the hair in its natural direction.

6. Place the attachment comb onto your clipper and start by trimming the sides from the

bottom upwards. Hold the clipper lightly against the hair with teeth of the attachment

comb pointing up but flat against the head. Slowly lift the clipper up and outward through

the hair, cutting only a small amount at a time

7. Repeat around sides and back of head.

8. If you desire shorter hair, either change to a lower number attachment comb or apply

more pressure and less lift away from head with the present attachment comb.

9. This entire procedure requires practice, and it is always better to leave too much hair

the first few haircuts.

CARE AND MAINTENANCE

Should your Grooming Solutions Hair Clipper Set fail to operate please check that it is

being used in accordance with these instructions.

If after checking the above the product is found to be faulty and it is still within its

guarantee period,

it should be returned to your nearest Boots store stocking this product together with

proof of purchase.

NEVER wrap the cord around the clippers because this can damage the cable and may

lead to premature cable failure.

Regularly inspect the clippers and the mains cable for signs of damage. If the clippers or

its power cable is found to be damaged it should be scrapped.

If the clippers are damaged they should NOT be used. This product contains no user

serviceable parts.

CLEANING

Before cleaning, ensure the clippers are disconnected from the mains supply.

Clean the outside of the clippers body using a damp, not wet, cloth and dry thoroughly

before using.

Clean the outside of the clippers head by gently wiping with a tissue and brushing any

hair residue from the cutter using the brush provided.

DO NOT immerse in water.

DO NOT use petroleum based or flammable cleaning agents because of fire risk.

DO NOT use abrasive cleaning agents.

OIL

To maintain your clipper in peak condition, the blades should be oiled every few haircuts.

Only use oil specifically designed for Clippers.

Page is loading ...

A.

B.

C.

D.

E.

/

Page is loading ...

King Clippo K 074 User manual

King Clippo K 074 User manual

in other languages

Related papers

Other documents