Aplisens PCE-28.Modbus User manual

Brand: Aplisens

Model: PCE-28.Modbus

Type: User manual

This manual is also suitable for

Aplisens PCE-28.Modbus is a pressure transmitter that allows for precise and reliable measurement of pressure. It features a digital Modbus RTU output, which enables seamless integration with industrial automation systems. This transmitter is designed for use in various applications, including process control, monitoring, and data acquisition. The PCE-28.Modbus offers flexibility and ease of use, making it an ideal choice for demanding industrial environments.

USER’S MANUAL

PRESSURE TRANSMITTERS

PCE-28, PCE-28.Smart, PCE-28 Ex Safety

PC-29A, PC-29B, PCE-28.Modbus

DIFFERENTIAL PRESSURE TRANSMITTERS

PRE-28, PRE-28.Smart, PRE-28 Ex Safety

PR-29A, PR-29B, PRE-28.Modbus

Flameproof (Exd) version

IO.PCE-28….PC-29.Exd

MARCH 2019

APLISENS S.A., 03-192 Warszawa, ul. Morelowa 7

tel. +48 22 814 07 77; fax +48 22 814 07 78

www.aplisens.pl, e-mail: [email protected]

04.A.004

Symbols used

Symbol

Description

Warning to proceed strictly in accordance with the information contained in the

documentation in order to ensure the safety and full functionality of the device

Information particularly useful during installation and operation of the device

Information particularly useful during installation and operation of Ex

versions

Information on disposal of used equipment

BASIC REQUIREMENTS AND SAFE USE

 The manufacturer will not be liable for damage resulting from incorrect

installation, failure to maintain the device in a suitably functional condition, or

use of the device other than for its intended purpose.

 Installation should be carried out by qualified personnel having the necessary

authorisation to install electrical and pressure measuring devices. The

installer is responsible for performing the installation in accordance with these

instructions and with the electromagnetic compatibility and safety regulations

and standards applicable to the type of installation.

 In the installation with control and measurement instruments exists, in case of

leakage, a risk to personnel on the side where the medium is under pressure.

All safety and protection requirements must be observed during installation,

operation and inspections.

 If a device is not functioning correctly, disconnect it and send it for repair to

the manufacturer or to a firm authorised by the manufacturer.

In order to minimise the risk of malfunction and associated risks to personnel, the

device is not to be installed or used in particularly hostile conditions, where the

following risks occur:

 Possibility of mechanical impacts, excessive shocks and vibration;

 Excessive temperature fluctuation;

 Condensation of water vapour, dust, icing.

When using the device in potentially explosive areas, observe technical

requirements specified in this manual and applicable local (national) regulations.

Changes in the manufacture of transmitters can overtake the update's paper documentation.

Current manuals can be found on the manufacturer's website at www.aplisens.com

IO.PCE-28….PC-29.Exd

04.A.004

CONTENTS

1. INTRODUCTION .......................................................................................... 3

2. SAFETY PROCEDURES ............................................................................. 4

3. USER INFORMATION ................................................................................. 4

4. TRANSPORT AND STORAGE .................................................................... 4

4.1. Transport ..................................................................................................................... 4

4.2. Storage ....................................................................................................................... 4

5. WARRANTY ................................................................................................ 5

6. CONSTRUCTION ........................................................................................ 5

6.1. Intended use and functions ......................................................................................... 5

6.2. Construction and dimensions ...................................................................................... 5

6.3. Identification ................................................................................................................ 8

7. USING OF PCE-28…PC-29 TRANSMITTERS IN HAZARDOUS AREAS ... 9

7.1. Exd versions in accordance with ATEX ....................................................................... 9

7.2. Exd versions in accordance with IECEx ...................................................................... 9

7.3. Electrostatic hazards ................................................................................................. 10

8. INSTALLATION ......................................................................................... 10

8.1. General recommendation .......................................................................................... 10

8.2. Installation in areas with dust explosion hazard ........................................................ 10

9. ELECTRICAL CONNECTIONS ................................................................. 11

9.1. How to connect different types of transmitters .......................................................... 11

9.2. How to connect transmitters in potentially explosive areas ....................................... 12

9.3. Grounding ................................................................................................................. 15

10. TECHNICAL DATA .................................................................................... 15

10.1. Electrical parameters ................................................................................................ 15

10.2. Metrological parameters ............................................................................................ 15

10.3. Permitted environmental conditions .......................................................................... 15

10.3.1. Electromagnetic compatibility, immunity............................................................. 15

10.3.2. Electromagnetic compatibility, emissions ........................................................... 16

10.3.3. Mechanical immunity .......................................................................................... 16

10.3.4. Electrical Isolation .............................................................................................. 16

10.3.5. Insulation strength .............................................................................................. 16

10.3.6. IP protection ratings ........................................................................................... 16

11. INSPECTIONS. SPARE PARTS ................................................................ 17

11.1. Periodic inspections .................................................................................................. 17

11.2. Unscheduled inspections .......................................................................................... 17

12. SCRAPPING, DISPOSAL .......................................................................... 17

12.1. Additional information ................................................................................................ 17

IO.PCE-28….PC-29.Exd

04.A.004

LIST OF FIGURES

Figure 1. Pressure transmitter PCE-28, PCE-28 Ex Safety, PCE-28.Smart, PC-29A, PC-

29B, PCE-28.Modbus. Dimensions ........................................................................ 6

Figure 2. Pressure transmitter PRE-28, PRE-28 Ex Safety PRE-28.Smart, PR-29A, PR-

29B, PRE-28.Modbus. Dimensions ......................................................................... 6

Figure 3. Electrical connections of the transmitters PC(R)E-28, PC(R)E-28 Ex Safety,

PC(R)E-28.Smart, PC(R)-29A, PC(R)-29B, PC(R)E-28.Modbus ............................ 7

Figure 4. PC(R)E-28, PC(R)E-28.Smart, PC(R)-29A, PC(R)-29B, PC(R)E-28.Modbus

rating plate (example) ............................................................................................. 8

Figure 5. Transmitter installed in the hazard zones ................................................................. 9

Figure 6. Wiring diagram transmitters PCE-28, PRE-28, PCE-28 Ex Safety, PRE-28 Ex

Safety .................................................................................................................... 13

Figure 7. Wiring diagram transmitters PCE-28.Smart, PRE-28.Smart. ................................. 13

Figure 8. Wiring diagram transmitters PC-29A, PR-29A, PC-29B, PR-29B .......................... 13

Figure 9. PCE-28.Modbus, PRE-28.Mobdus electrical connection ....................................... 14

IO.PCE-28….PC-29.Exd

04.A.004

1. INTRODUCTION

The subject of this manual are:

 Pressure transmitters PCE-28;

 Pressure transmitters PCE-28 Ex Safety;

 Smart pressure transmitters PCE-28.Smart;

 Pressure transmitters PC-28E.Modbus;

 Pressure transmitters PC-29A, PC-29B;

 Differential pressure transmitters PRE-28;

 Differential pressure transmitters PRE-28 Ex Safety;

 Smart differential pressure transmitters PRE-28.Smart;

 Differential pressure transmitters PRE-28.Modbus

 Differential pressure transmitters PR-29A, PR-29B

This manual contains data, information and recommendations concerning installation and

use of the transmitter, as well as troubleshooting procedures.

Transmitters are designed and manufactured in accordance with the other requirements

provided with the rating plate and Declarations of Conformity. Transmitters comply with EU

directives:

ATEX

ATEX directive, Exd version, certificate KDB 18 ATEX 0077X

Additional information about transmitters: PCE–28, PRE–28, PCE–28.Smart,

PRE–28.Smart, PCE–28.Modbus, PRE–28.Modbus, PCE-28 Ex Safety;

PRE-28 Ex Safety and PC–29A, PC–29B, PR–29A, PR–29B Exd versions

according to ATEX, see p. 7.1.

IECEx

IECEx system, Exd version, certificate IECEx KDB 18.0005X

Additional information about transmitters: PC–28, PR–28, PC–28.Smart,

PR–28.Smart, PC–28.Modbus, PR–28.Modbus, PC-28 Ex Safety; PR-28 Ex

Safety and PC–29A, PC–29B, PR–29A, PR–29B Exd versions according to IECEx,

see p. 7.2.

EMC

EMC directive.

Pressure and differential pressure transmitters: PC–28, PR–28, PC–28.Smart,

PR–28.Smart, PC–28.Modbus, PR–28.Modbus and PC–29A, PC–29B, PR–29A,

PR–29B in all versions comply with EMC directive according to:

PN-EN 61326-1:2013-06.

RoHS

RoHS directive.

Pressure and differential pressure transmitters: PC–28, PR–28, PC–28.Smart,

PR–28.Smart, PC–28.Modbus, PR–28.Modbus and PC–29A, PC–29B, PR–29A,

PR–29B in all versions comply with RoHS directive according to:

PN-EN 50581 :2013-03.

IO.PCE-28….PC-29.Exd

04.A.004

2. SAFETY PROCEDURES

 The installation and commissioning of the transmitter and any activities related

to the operation should be performed only after careful examination of the

contents of this manual.

 Installation and maintenance should be carried out by qualified personnel

having necessary authorisation to install electrical equipment and measuring

instruments.

 The transmitter should be used according to its intended purpose (section 6.1)

with permissible parameters.

 Before assembly or disassembly of the transmitter, one must absolutely

disconnect the power source.

 Under no circumstances may the electrical system of the transmitter be

repaired or otherwise handled by the user. Damage assessments and repairs

may only be carried out by the manufacturer or its authorised dealer.

 Do not use damaged device. If a device is not functioning correctly, disconnect

it.

 When using the device in potentially explosive areas, observe technical

requirements specified in this manual and applicable local (national)

regulations.

3. USER INFORMATION

The user receives together with the transmitter:

a) Product Certificate, which is also a warranty card;

b) Declaration of Conformity;

c) Copy of the certificate (on request);

d) User Manual ref. No. IO.PCE-28…PC-29(ENG).

Items b), c) and d) are available on the website www.aplisens.com

4. TRANSPORT AND STORAGE

4.1. Transport

Transmitters should be transported in multi- or/and single-unit packaging. The packaging

should be protected against displacement and direct weathering effect.

4.2. Storage

The transmitter should be stored in the original packaging, indoor rooms, free of vapours

and corrosive substances, the temperature and relative humidity should not exceed the

permitted conditions (see individual transmitters data sheet).

IO.PCE-28….PC-29.Exd

04.A.004

5. WARRANTY

Manufacturer warrants to the conditions specified in the Product Certificate which is also

a guarantee card.

Warranty is in full force under the condition of using the devices properly along

with the purpose determined in the manual.

6. CONSTRUCTION

6.1. Intended use and functions

Pressure transmitters are designed to measure overpressure, vacuum pressure and

absolute pressure of gases, vapours and liquids (including corrosive).

Differential pressure transmitters are designed to measure the level in closed tanks

and to measure differential pressure at accumulating elements such as filters and

measuring orifices.

Differential pressure transmitters with P-type tubes may operate at static pressures of up

to 4 MPa.

Pressure and differential pressure transmitters may also be equipped with a number

of process connectors, which make it possible to use them with different media such as

dense or aggressive media and for low and high medium temperatures. Examples of

process connectors are listed in point 6.2.

6.2. Construction and dimensions

The main units of transmitters include: measuring head in which a pressure signal is

converted into an electric signal; electronic unit that converts the measuring head signal

into a unified transmission signal; housing and type SGM or FL Exd electrical connector.

Made of a ⌀27 pipe, the transmitter casing is inseparably connected to the measuring

head and electric connector.

Male thread in the electrical connection allows the transmitter to be screwed into an

element such as a flameproof housing, strengthened housing, etc.

IO.PCE-28….PC-29.Exd

04.A.004

Figure 1. Pressure transmitter PCE-28, PCE-28 Ex Safety, PCE-28.Smart, PC-29A, PC-29B,

PCE-28.Modbus. Dimensions

Figure 2. Pressure transmitter PRE-28, PRE-28 Ex Safety PRE-28.Smart, PR-29A, PR-29B,

PRE-28.Modbus. Dimensions

IO.PCE-28….PC-29.Exd

04.A.004

Transmitter can be equipped with:

 “M” process connection, thread M20x1,5;

 “P” process connection, thread M20x1,5 and 12 hole;

 “CM30x2” process connection, thread M30x2 with flush diaphragm;

 “G 1/2” process connection, thread G1/2’’ and 4 hole;

 “GP” process connection, thread G1/2’’ with flush diaphragm;

 “CG1” process connection, thread G1’’ with flush diaphragm;

 “RM” process connection, thread M20x1,5 with 4 hole and radiator;

 “RP” process connection, thread M20x1,5 with 12 hole and radiator;

 “G 1/4” process connection, thread G1/4’’ male;

 “1/2NPT” process connection, thread 1/2NPT male;

 “R 1/2” process connection, thread R ½ and 4 hole;

 “CG 1/2” process connection, thread G1/2’’ with flush diaphragm;

 ”9/16-18 UNF” process connection autoclave F-250 compatible;

 ”1/4NPTF” process connection, thread 1/4NPT female;

 ”1/2NPTF” process connection, thread 1/2NPT female;

 Other on request.

Differential pressure transmitter measuring head can be equipped with :

 P type with M20x1,5 thread process connection;

 Diaphragm seals: see Diaphragm Seals Data Sheets;

 Other on request.

SGM type electrical connection has hermetically sealed cable with poliurethane sheath

and is equipped with M20x1,5 or 1/2”NPT male thread.

FL type electrical connection has hermetically sealed wires with PVC insulation and

M20x1,5 or 1/2”NPT male thread.

Electrical connection designations:

FL (M20x1,5), FL (1/2”NPT) –2, 3 or 4 according to 9.1 0,5mm2 PVC insulated loose wires

length: 180cm

SGM (M20x1,5), SGM (1/2”NPT) – PUR (polyurethane) cable length: 350cm

Figure 3. Electrical connections of the transmitters PC(R)E-28, PC(R)E-28 Ex Safety,

PC(R)E-28.Smart, PC(R)-29A, PC(R)-29B, PC(R)E-28.Modbus

IO.PCE-28….PC-29.Exd

04.A.004

6.3. Identification

Transmitters are provided with a rating plate containing:

1. Manufacturer name and/or logotype;

2. CE marking;

3. Number of notified body;

4. Product code;

5. Type of transmitter: „Pressure transmitter” or „Differential pressure transmitter”;

6. Transmitter type designation;

7a.Process connection designation;

7b.Electrical connection designation;

8. Measuring range;

9a.Permissible ambient temperature range;

9b.Permissible process temperature range;

10. Output signal;

11. Serial number;

12. Maximum static pressure (only for differential pressure transmitters);

13. Supply voltage;

14. Year of production;

15. Diaphragm seal material;

16. IP code;

17. Symbol „Notice”. See relevant information contained in the manual;

18. Ex mark;

19. Kind of flameproof housing designation, certificate designation;

20. Address of the manufacturer.

Figure 4. PC(R)E-28, PC(R)E-28.Smart, PC(R)-29A, PC(R)-29B, PC(R)E-28.Modbus rating plate

(example)

IO.PCE-28….PC-29.Exd

04.A.004

7. USING OF PCE-28…PC-29 TRANSMITTERS IN

HAZARDOUS AREAS

7.1. Exd versions in accordance with ATEX

The transmitters PCE-28, PCE-28 Ex Safety, PCE-28.Smart, PC-29A, PC-29B,

PC-28.Modbus and pressure transmitters PRE-28, PRE-28 Ex Safety, PRE-28.Smart,

PR-29A, PR-29B, PRE-28.Modbus may operate in potentially explosive areas and are

marked:

II 2G Ex db IIC T6/T5/T4 Gb

II 2D Ex tb IIIC T85°C/T100°C/T120°C Db

KDB 18 ATEX 0055X

The transmitters are produced in accordance with the requirements of the following

standards:

EN 60079-0:2012 + A11:2013, EN 60079-1: 2014, EN 60079-31:2014.

7.2. Exd versions in accordance with IECEx

The transmitters PCE-28, PCE-28 Ex Safety, PCE-28.Smart, PC-29A, PC-29B, PCE-

28.Modbus and pressure transmitters PRE-28, PRE-28 Ex Safety, PRE -28.Smart, PR-

29A, PR-29B, PRE-28.Modbus may operate in potentially explosive areas and are

marked:

Ex db IIC T6/T5/T4 Gb

Ex tb IIIC T85°C/T100°C/T120°C Db

IECEx KDB 18.0005X

The transmitters are designed and produced in accordance with standards:

IEC 60079-0:2011 Ed.6, IEC 60079-1:2014 Ed.7, IEC 60079-31:2013 Ed.2

Figure 5. Transmitter installed in the hazard zones

Installation in potentially explosive areas is describe in p. 8.

Connection in potentially explosive areas is shown in p. 9.

IO.PCE-28….PC-29.Exd

04.A.004

7.3. Electrostatic hazards

The non-conductive layer applied onto the conductive substrate is comprised of a plastic

plate. In areas with dust explosion hazard, these transmitters should be installed in such a

manner as to ensure that there is no electrostatic charging, especially through contact with

charged dust escaping or blown from nearby equipment.

8. INSTALLATION

8.1. General recommendation

Given their small weight and size, transmitters may be mounted directly on rigid impulse

pipes.

When selecting assembly components, it may be helpful to refer to information on

connection elements, reduction elements, sockets, valves, reduction clamps and signal

tubes provided by APLISENS.

Further data may be found in the "Valves and fitting accessories" catalogue card.

While installing and using the transmitter, the diaphragm should not be exposed to

damage. The transmitter diaphragm is made of acid-resistant steel or of

Hastelloy and cannot be exposed to media that may damage it.

8.2. Installation in areas with dust explosion hazard

The 2G (2D) category of the transmitter means that the transmitter and process connector

may be installed in a hazardous area of a 1st (21) or 2nd (22) class (example is shown in

Fig. 5).

Wires or cable must not be exposed to mechanical damage.

In order to protect the wires or cable against mechanical damage and to maintain

protection degree IP66 and IP68 (see item 10.3.6.), screw the SGM or FL electric

connection into the cover or tube using:

- for 1/2 "NPT thread - Loctite 577 sealing.

- for thread M20x1,5 - gasket.

The M20x1,5-6g and 1/2"NPT electric connection threads are made with accuracy

ensuring that a flameproof Exd joint is formed.

Temperature class and maximum surface temperature depending on ambient temperature

Ta and process temperature Tp:

Operating temperature range

Temperature class and

maximum surface

temperature

Ambient

temperature

Process

temperature

Ta ≤ 70ºC

Ta ≤ 80ºC

Tp ≤ 70ºC

Tp ≤ 85ºC

Tp ≤ 115ºC

T6/T85ºC

T5/T100ºC

T4/T120ºC

Transmitters with FL electric

connection

(with LgYc wires with PVC insulation)

Ta ≤ 65ºC

Tp ≤ 75ºC

Tp ≤ 105ºC

T6/T85ºC

T5/T100ºC

Transmitters with SGM electric

connection

(with LiYwC11Y (1) 4x0,35c cable

with polyurethane insulation)

IO.PCE-28….PC-29.Exd

04.A.004

Low ambient temperature for pressure transmitters is -40ºC,

Low ambient temperature for differential pressure transmitters is -25ºC

Low ambient temperature for special versions transmitters is -50ºC

Special conditions for safe use

̶ Transmitters with LiYwC11Y (1) 4x0,35c type cable (manufactured by Technokabel)

(SGM electric connection), used at an ambient temperature of Ta = 65°C and process

temperature 105°C, must be installed in a horizontal position in such a way that the

temperature above the process connection does not exceed 100°C.

̶ If transmitters for Group III contain:

a) the nameplate made of plastic,

b) diaphragm seals covered by PTFE,

they should be installed in a way that prevents electrostatic charging, according to

the instruction manual.

̶ If the elements made of titanium are used in the construction of the device, during

installation and operation of the transmitter these elements should be protected against

direct access.

̶ External parts made of plastic should be cleaned with a damp cloth, with the addition of

antistatic fluids.

̶ The diaphragm should not be subject on damage during installation and exploitation of

the transmitter. The transmitter diaphragm is made of stainless steel or Hastelloy alloy

and must not be exposed to medium that could cause its damage.

9. ELECTRICAL CONNECTIONS

All connection and installation activities should be performed when the power

supply and input signal are disconnected.

It is recommended to transmit signal lines through a shielded cable. Signal cables should

not be led with interfering cables e.g. near large load points.

Equipment operating together with transmitters should be resistant to electromagnetic

interference from the transmission line in compliance with electromagnetic compatibility

requirements.

It is also beneficial to use noise filters on the primary side of transformers, power supplies

for transmitters and apparatus operating with them

9.1. How to connect different types of transmitters

PCE-28, PRE-28, PCE-28 Ex Safety, PRE-28 Ex Safety connection

„FL(…)” connection

„SGM(…)” connection

Red wire (+)

Black wire (-)

Green wire (cable shield)

IO.PCE-28….PC-29.Exd

04.A.004

PCE-28.Smart, PRE-28.Smart connection

„FL(…)” connection

„SGM(…)” connection

Red wire (+)

Black wire (-)

Green wire (cable shield)

PCE-28.Modbus, PRE-28.Modbus connection

„FL(…)” connection

„SGM(…)” connection

Red wire (+)

Black wire (-)

Blue wire (VA)

Yellow wire (VB)

Green wire (cable shield)

PC-29A, PR-29A, PC-29B, PR-29B connection.

„FL(…)” connection

„SGM(…)” connection

Red wire (+)

Black wire (-)

Blue wire (OUT)

Green wire (cable shield)

9.2. How to connect transmitters in potentially explosive areas

General principles in relation to connecting and using Exd transmitters should be

consistent with the rules and standards concerning equipment with flame-proof housing as

in point 7.1, including:

EN60079-14 - Electrical equipment in potentially explosive atmospheres. Part 14:

Electrical installation in risk areas (other than mines).

EN60079-17 - Electrical equipment in potentially explosive atmospheres. Part 17:

Inspection and operation of electrical installation in hazardous areas (other than mines).

Cables should be protected against damage by laying them in cable trays, lining

pipes, cable ladders, using durable fastenings etc.

Transmitters and equipment in a transmitter measurement loop should be

connected in accordance with explosion-proof standards and conditions of use in

hazardous areas.

Failure to comply with explosion-proof may result in an explosion and risk to

humans associated with it.

Transmitters should be powered by power supplies or other equipment that

ensures that there is reinforced insulation between primary and secondary

windings and which do not exceed 250V AC. It is the user who is responsible for

the provision of power supply in compliance with the aforementioned

requirements.

IO.PCE-28….PC-29.Exd

04.A.004

Transmitters should be supplied in accordance with the following diagrams

Figure 6. Wiring diagram transmitters PCE-28, PRE-28, PCE-28 Ex Safety, PRE-28 Ex Safety

Figure 7. Wiring diagram transmitters PCE-28.Smart, PRE-28.Smart.

Figure 8. Wiring diagram transmitters PC-29A, PR-29A, PC-29B, PR-29B

IO.PCE-28….PC-29.Exd

04.A.004

Figure 9. PCE-28.Modbus, PRE-28.Mobdus electrical connection

IO.PCE-28….PC-29.Exd

04.A.004

9.3. Grounding

Transmitters should be grounded in accordance with local electrical standards.

It is recommended to ground transmitters by a process connector.

10. TECHNICAL DATA

10.1. Electrical parameters

Transmitter

Power supply

Signal output

PCE-28, PRE-28,

8÷30V DC

4÷20mA

PCE-28 Ex Safety, PRE-28 Ex Safety

10,5÷30V DC

4÷20mA

PCE-28.Smart, PRE-28.Smart.

7,5÷30V DC

4÷20mA + Hart

PCE-28.Modbus, PRE-28.Modbus.

4÷28V DC

MODBUS RTU

PC-29A, PR-29A

7,5...16V DC

0,5...4,5V

8...16V DC

1...5V

0...5V

13...16V DC

0...10V

PC-29B, PR-29B

3,3...5,6V DC

0...2V

3,5...5,6V DC

0...2,5V

4...5,6V DC

0...3V

4,3...5,6V DC

0...3,3V

3,3...5,6V DC

0,4...2V

3,5...5,6V DC

1...2,5V

Power supply ≤ 1W

For other parameters see 8.2. and transmitter’s data sheet.

10.2. Metrological parameters

See individual transmitter’s data sheet.

10.3. Permitted environmental conditions

See 8.2. and individual transmitter’s data sheet.

10.3.1. Electromagnetic compatibility, immunity

Assessment acc. to PN-EN 61326-1 for industrial applications:

Electrostatic discharges (ESD):

PN-EN 61000-4-2

level S3; contact ±6kV; air ±8kV; criterion B;

Conducted interferences inducted by fields with radio frequency:

PN-EN 61000-4-6

0,15…80MHz, 3V; Criterion A;

IO.PCE-28….PC-29.Exd

04.A.004

Electromagnetic fields (radiated interferences):

PN-EN 61000-4-3

80…2000MHz - 10V/m; …2700MHz - 1V/m; Criterion A;

Fast electrical transient conditions (Burst):

PN-EN 61000-4-4

± 2kV supply lines; ± 1kV signal lines; Criterion B;

Surges:

PN-EN 61000-4-5

± 0,5kV (±1kV) signal lines - enclosure; ± 1kV (±2kV) supply lines - enclosure; Criterion B;

10.3.2. Electromagnetic compatibility, emissions

Measurements acc. to CISPR 16-1, CISPR 16-2, class B;

Distance of antenna 3m, quasi-peak measurements:

Radiation:

0,15…30MHz; 80-52dBµV/m;

30…2000MHz; <54dBµV/m;

Inductions:

0,01…0,15MHz; 96-50dBµV/m;

0,15…0,35MHz; 60-50dBµV/m;

0,35…30MHz; <50dBµV/m;

10.3.3. Mechanical immunity

Shocks:

PN-EN 60068-2-27, 31

50g/11ms

Sinusoidal vibrations:

PN-EN 60068-2-6, Fc test;

to 1,6mm; 2…25Hz;

to 4g for 25…100Hz;

10.3.4. Electrical Isolation

>100MΩ @110V DC

10.3.5. Insulation strength

75V AC (110V DC), 1 min

10.3.6. IP protection ratings

Acc. PN-EN 60529:2003

- IP68 – for transmitters designed to measurement of underpressure or absolute pressure.

- IP66 – for transmitters designed to measurement of pressure.

IO.PCE-28….PC-29.Exd

04.A.004

11. INSPECTIONS. SPARE PARTS

11.1. Periodic inspections

During inspection, the connectors should be checked for loose connections and leaks, the

electrical connectors should be checked with regard to tightness and the state of the

housing, gaskets, cable glands, and the diaphragm seals should be checked for tarnishing

and corrosion. Readability of the tag should also be checked.

11.2. Unscheduled inspections

If the transmitter is installed in a location where it could be subjected to mechanical

damage, electrical surges or malfunction is found - inspect it as needed.

In case of lack of signal in the transmission line or its incorrect value, check the state of the

cable, of the connection on terminals, etc. Determine whether the values of the supply

voltage and load resistance are correct. If the communicator is connected to the

transmitter power supply line, an indication of a fault line may be the message "No

response" or "Check connection". If the line is in order, check operation of the transmitter.

12. SCRAPPING, DISPOSAL

Waste or damaged transmitters should be dismantled and disposed of in

accordance with Directive (2012/19/EU) on waste electrical and electronic

equipment (WEEE) or returned to the manufacturer.

12.1. Additional information

The manufacturer reserves the right to make constructional and technological changes

which do not lower the quality of the transmitters.

Aplisens PCE-28.Modbus User manual

Brand: Aplisens

Model: PCE-28.Modbus

Type: User manual

This manual is also suitable for

Download PDF

report

Aplisens PCE-28.Modbus User manual

This manual is also suitable for

Aplisens PCE-28.Modbus User manual

Other documents