Fiori P44W Instructions And Advice For The Use, Installation And Maintenance

Brand: Fiori

Model: P44W

Category: Hobs

Type: Instructions And Advice For The Use, Installation And Maintenance

This manual is also suitable for

Fiori P44W is a built-in gas hob with 4 burners designed for domestic use. Two of the burners are semirapid burners, one rapid burner and one auxiliary burner. The appliance is equipped with automatic electrical ignition for easy and safe lighting of the burners. It has a sleek design with a black tempered glass surface that is easy to clean and maintain. The dimensions of the hob are 600mm in width, 510mm in depth, and 50mm in height.

COD. 208217 - REV 0 - 14.11.2006

Dear Customer,

Thank you for having purchased one of our products.

We are certain that this new modern functional and practical appliance, built with the very

highest quality materials, will meet your requirements in the best possible way. This appliance

is easy to use, it is however important to thoroughly read the instructions in this handbook, in

order to obtain the best results.

These instructions are only valid for Australia, these instructions are only applicable to the

instruction manual as indicated and on the appliance itself.

Fiori shall not be held responsible for any damages to persons or property caused by incorrect

installation or use of the appliance.

INSTRUCTIONS AND ADVICE FOR THE USE,

INSTALLATION AND MAINTENANCE OF

BUILT-IN GAS HOBS

MODELS: P44W / P44I / P44TCW / P44TCI

Fiori shall not be held responsible for any inaccuracies in this handbook due to printing or

transcription errors; the designs in the figures are purely indicative. Fiori also reserves the

right to make any modifications to the products as may be considered necessary or useful,

also in the interests of the user, without jeopardizing the main functional and safety features of

the products themselves.

Natural Propane

1 Semirapid Burner 7.3 MJ 6.9 MJ

2 Wok Burner 14.5 MJ 14.5 MJ

3 Rapid Burner 12.0 MJ 12.0 MJ

4 Auxiliary Burner 4.2 MJ 3.8 MJ

5 Semirapid Burner

6 Auxiliary Burner control nr. 4

7 Semirapid Back Burner control nr. 1

8 Wok Burner control nr. 2

9 Rapid Burner control nr. 3

10 Semirapid Front Burner control nr. 5

DESCRIPTION OF THE HOT PLATES

Appliance dimensions (mm)

Width mm. 600

Depth mm. 510

Height mm. 50

Attention: this appliance has been manufactured for domestic use only

P44W - P44I P44TCW - P44TCI

600

510

Gas Connection Electrical Supply

Cord

107

600

510

Gas Connection Electrical Supply

Cord

107

USE

1) BURNERS

A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner

the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners

as described below:

- Automatic electrical ignition

Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches

the full on position (large flame fig. 1), then depress the knob for about 2-3 seconds or until the burner

lights.

HOW TO USE THE BURNERS

Bear in mind the following indications in order to achieve maximum efficiency with the least possible gas

consumption:

Use adequate pans for each burner (consult the following table and fig. 2).

When the pan comes to the boil, set the knob to the reduced rate position (small flame fig. 1).

Always place a lid on the pans.

Burners Power ratings Pan Ø in cm

Natural Propane

Wok 14.5 MJ 14.5 MJ 22 ÷ 24

Rapid 12.0 MJ 12.0 MJ 20 ÷ 22

Semirapid 7.3 MJ 6.9 MJ 16 ÷ 18

Auxiliary 4.2 MJ 3.8 MJ 10 ÷ 14

WARNINGS:

Matches can be used to ignite the burners in a blackout.

Never leave the appliance unattended when the burners are being used. Make sure there are no

children in the near vicinity. Particularly make sure that the pan handles are correctly positioned

and keep a check on foods requiring oil and grease to cook since these products can easily catch

fire.

Utilize pots with flat bottom only.

Do not use or store flammable materials in or near this appliance.

For LPG appliances: where this appliance is installed in marine craft or in caravans, it shall not be

used as a space heater.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

•

Fig.1 Fig.2

Maximum

Minimum

USE

Notes:

Use of a gas cooking appliance produces heat and moisture in the room in which it is installed.

The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by

activating the mechanical aeration device (suction hood or electric fan fig. 4 and fig. 5).

Intensive and lengthy use of the appliance may require additional ventilation. This can be

achieved by opening a window or by increasing the power of the mechanical exhausting system if

installed.

Abnormal Operation:

Any of the following are considered to be abnormal operation and may require servicing:

- Yellow tipping of the hob burner flame.

- Sooting up of cooking utensils.

- Burners not igniting properly.

- Burners failing to remain alight.

- Burners extinguished by cupboard doors.

- Gas valves which are difficult to turn.

In case the appliance fails to operate correctly, contact FIORI for your closest authorised service

provider in your area.

REGULATIONS FOR YOUR SAFETY

* Young and infirm SHALL not use UNLESS supervised.

* CHILDREN MUST NOT PLAY WITH THIS APPLIANCE

* This appliance will become HOT in use KEEP children AWAY

* DO NOT steam CLEAN this appliance.

If the appliance fails to operate correctly, contact FIORI for your authorised Agent

Fig.3 Fig.4 Fig.5

(*) Air inlet - minimum section 100cm.

CLEANING THE GAS HOB

CAUTION

Always disconnect or isolate the hob assembly from the Gas and Electricity supply, before

carrying out any cleaning or maintenance operation.

To ensure correct and efficient operation of the Hob assembly, periodically wash/wipe all of the surfaces of

the assembly with a damp cloth.

Periodically wash in luke warm water after they have cooled to touch and remove any heavy deposits

gently from any of the following parts:

* the trivets – or the enamelled pan supports,

* the burner cap,

* the burner head,

* the burner-ring; if supplied.

Note: All of the components are freely mounted above the Hob surface and are easily removed without

tools.

* Never use aggressive or abrasive detergents or cleaning powders.

* All parts should be thoroughly rinsed and dried before re-assembly.

* Do not allow: cooking overspill, splashings of vinegar, coffee, milk, salted water, lemon or tomato juice,

or other corrasive material to remain on the surface of the Hob or components for any extended period of

time.

* Ensure that the Ignition plug is clean and free of foreign matter.

WARNINGS:

Ensure the following is carried out before re-assembling the components.

Check that the burner head slots are not clogged with foreign matter – carbon etc.

Ensure that the enamelled cap, burner head and ring; if supplied, are correctly positioned on the

burner base – wich protrudes through the Hob surface. The assembly must feel steady.

The Trivets or Pan-supports must be positioned, so that the rounded corners are set adjacent to

the side-edges of the Hob top-plate.

Do not force the Gas cocks/taps, if they are difficult to operate – open or close – contact the

Tecnical Assistance Service for advise or repairs.

There are Commercially available products that keep the surfaces clean and resistant to possible

formation of rusting, should the surface be damaged.

Don't use steam jets for the equipment cleaning.

•

Fig.6 Fig.7

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

This appliance shall be installed only by Licensed Authorised Personnel and in accordance with

the manufacturer’s installation instructions, local gas fitting regulations, municipal building

codes, water supply regulations, electrical wiring regulations, AS 5601/AG 601 –

Gas Installations hereafter referred to as the Standard and any other statutory regulations.

* Ensure that the point of connection to the gas supply is accessible when the appliance is installed.

* The appliance may be connected to the gas supply by either rigid or a flexible hose.

* Where a flexible hose is used the length should be 600 mm, but SHALL not exceed 1200 mm, it shall be

of a type that complies with Class B of AS 1869 - refer to AS5601; gas installation.

2) INSTALLING THE COOKTOP

Check that the appliance is in a good condition after having removed the outer packaging and internal

wrappings from around the various loose parts. If in any doubt, do not use the appliance and contact a

qualified technician.

Never leave the packaging materials (cardboard, bags, polystyrene foam, staples, etc.) within

children’s reach since they could become potential sources of danger.

The measurements of the opening made in the top of the modular cabinet and into which the cooktop will

be installed are indicated in fig. 8. Always comply with the measurements given for the hole into which the

appliance will be recessed (see fig. 9).

- The hob SHALL NOT be installed below or adjacent to curtains or the like.

For other combustible materials the following clearance SHALL be maintained :

600mm in a vertical distance and 200mm in a horizontal distance.

3) CLEARANCES

Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions.

However, in no case shall the clearance between the highest part of the hob of the cooking appliance and

a range hood be less than 600 mm or, for an overhead exhaust fan, 760 mm (see fig. 9).

Any other downward facing combustible surface less than 600 mm above the highest part of the hob shall

be protected for the full width and depth of the cooking surface area in accordance with the Standard.

However, in no case shall this clearance to any surface be less than 450 mm.

Where the distance between the outer edge of any burner assembly is less than 200mm from a vertical

combustible surface, that area shall be protected in accordance with the Standard.

Fig.8 Fig. 9

INSTALLATION

CAUTION:

The hob SHALL not be installed below or adjacent to curtains or the like

For other combustible materials the following clearances SHALL be maintained;

- 600 mm in a vertical distance and 200 mm in a horizontal distance

4) FIXING THE COOKTOP

The hot plate has a special seal which prevents liquid from getting into the cabinet. Strictly comply

with the following instructions in order to correctly apply this seal:

Detach the seals from their backing, checking that the transparent protection still adheres to the seal itself.

Overturn the hot plate and correctly position seal “E” (fig. 10) under the edge of the hot plate itself, so that

the outer side of the seal perfectly matches the outer edge of the hot plate. The ends of the strips must fit

together without overlapping.

Evenly and securely fix the seal to the hot plate, pressing into place with the fingers and remove the strip

of protective paper from the seal and set the plate into the hole made in the cabinet.

The prospective walls cutout that exceed the working table in height must be at a minimum distance from

the cutting as mentionned both in the columns and the scheme.

In order to avoid accidental touching of overheated bottom of the hob, during operation, it is necessary to

put a wooden insert, fixed by screws, at a minimum distance of 50 mm from the top (see fig. 8).

5) LOCATION AND VENTILATION

Ventilation must be in accordance with AS5601/AG 601 – Gas Installations.

In general, the appliance should have adequate ventilation for complete combustion of gas, proper flueing

and to maintain temperature of immediate surroundings within safe limits.

6) GAS CONNECTION

Before connecting the appliance, check that the values on the data label affixed to the underside

of the cooktop correspond to those of the gas mains in the home.

A label on the appliance indicates the regulating conditions, type of gas and working pressure.

WARNING

A gas hob must only be connected by Licensed Authorised Person and in accordance with the

Standard AG601/AS5601 - Gas installation

This Gas Hob is NOT recommended for Maritime use.

* This appliance is suitable for a flexible connection;

- Natural Gas Fittings;

Regulator supplied, isolating valve and union are to be fitted.

- L.P.G. Propane Fittings;

Test point adaptor, isolating valve and union are to be fitted

•

Fig.10 Fig.11

Fig.12

Fig.13 Fig. 14

HOT PLATES WITH 4 BURNERS

IGNITION

GENERATOR

ELECTRIC

WIRING

DIAGRAM

230 - 240 V~

INSTALLATION

Gas connection:

All rigid and flexible hose MUST have continuos walls.

There Should be NO stress on the internal gas lines

On completion of the gas connection -

- check the connection seal with soapy water.

- check the gas setting pressure

- check and adjust the gas burners if necessary. - see page 9 for ADJUSTMENTS

7) ELECTRICAL CONNECTIONS

The data label can be found on the underside of the cooktop. Check that the voltage rating of the

appliance corresponds to the supply voltage. The Hob may be connected to a 3 core supply flexible cord

and a 10 ampere plug.

The electrical connections of the appliance must be carried out by a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED

Ensure that this power point is properly earthed. Look at the connection wiring diagrams (fig. 14).

ADJUSTMENT

Always turn off electrical ignition before making any adjustments.

All seals must be replaced by the technician at the end of any adjustments or regulations.

Our burners do not require primary air adjustment.

Data Label

The Data Label is located on the underside of the appliance. A duplicate Data Label is supplied to adhere

in an accessible area adjacent to the appliance. This appliance is suitable for Natural Gas and LPG;

ensure that the available gas supply matches the Data Label.

Before Leaving

Check all connections for gas leaks with soap and water.

DO NOT use a naked flame for detecting leaks. Ignite all burners to ensure correct operation of gas

valves, burners and ignition. Turn gas taps to low flame position and observe stability of the flame. Check

and adjust the gas pressure as per the Data Plate. When satisfied with the hotplate, please instruct the

user on the correct method of operation. In case the appliance fails to operate correctly after all checks

have been carried out, refer to the authorised service provider in your area.

8) GAS TAPS

Our gas taps are suitable for all gases, they are a male conical type.

“Reduced rate” adjustment

- Switch on the burner and turn the relevant knob to the “Reduced rate” position (small flame fig.1).

- Remove knob (fig. 15) of the tap, which is simply pressed on to its rod.

- Insert a small screwdriver “D” into the valve shaft (fig.15) and turn the throttle screw to the right or left

until the burner flame has been adequately regulated to the “Reduced rate” position.

Check that the flame does not go out when the knob is sharply switched from the “Full on” to the

“Reduced rate” position.

It is understood that only burners operating with Natural gas should be subjected to the above

mentioned adjustments. The screw must be fully locked when the burners operate with propane

gas.

Fig.15

CONVERSIONS

9) REPLACING THE INJECTORS

The burners can be adapted to different types of gas by installing injectors suited to the type of gas

required. To do this, first remove the burner tops using a wrench “B”. Now unscrew injector “A” (see fig.

16) and fit a injector corresponding to the type of gas required.

It is advisable to tighten the injector in place.

After the injectors have been replaced, the burners must be regulated as explained in paragraphs

8. The technician must reset any seals on the regulating or pre-regulating devices and affix the

label corresponding to the new gas regulation on the appliance instead of the already existing

one. This label is supplied in the packet containing the spare injectors.

The envelope with the injectors and the labels can be included in the kit, or at disposal to the

authorized customer Service Centre.

For the sake of convenience, the nominal rate chart also lists the heat inputs of the burners, the diameter

of the injectors and the working pressures of the various types of gas.

Fig.16

BURNERS GAS

NORMAL

PRESSURE

INJECTOR

DIAMETER

NOMINAL HEAT

INPUT

(MJ/h)

N° DESCRIPTION KPa 1/100 mm Max.

1 RAPID LPG 2.75 94 12.0

Natural 1.00 155 12.0

2 SEMI-RAPID LPG 2.75 73 6.9

Natural 1.00 120 7.3

3 AUXILIARY LPG 2.75 54 3.8

Natural 1.00 90 4.2

4 ULTRA RAPID LPG 2.75 106 14.5

Natural 1.00 176 14.5

BURNER ARRANGEMENTS ON THE HOT PLATE

NOT WORKING PROPERLY? (FAULT GUIDE)

* UNEVEN OR YELLOW FLAME RATHER THAN CLEAR BLUE

Switch off immediately and check the following points:

- Are the burners fitted correctly ?

- Are the burners and the holes in the burner cap clear ?

- Check that no dust has fallen into the flame turning it yellow. Relight and if the flame is still yellow, call

Customer Call Centre. DO NOT USE hob again until it has been serviced.

* BURNER FAILING TO IGNITE ?

Chek the power is turned on and that the fuse has not blown. Make sure that the igniter terminal isn’t

coated with food spillage, preventing it from sparking.

* SPARK BUT NO GAS ?

Make sure that gas is turned on. Check that the burner holes are not blocked.

* SMELL OF GAS ?

Check to see if any gas tap has been inadvertently left on. If they are all off, then immediately switch off

gas at mains and call Customer Call Centre. DO NOT under any circumstances press igniter or search for

leak with naked flame.

* STILL NOT WORKING ?

Call Customer Call Centre.

SAFETY WARNING

DANGER:

NEVER SPRAY AEROSOL IN THE VICINITY OF

THIS APPLIANCE WHILE IT IS IN OPERATION.

WHERE THIS APPLIANCE IS INSTALLED IN

MARINE CRAFT OR IN CARAVANS, IT MUST NOT

BE USED AS A SPACE HEATER

TO ACHIEVE LONGEVITY OF LIFE OF THE HOB,

HAVE THE UNIT CHECKED BY A SERVICE AGENT

EVERY 2 YEARS.

THIS IS NOT COVERED BY WARRANTY.

1212

Warranty Certificate (Australia)

Fiori Holdings Pty Ltd ABN 11 089 098 297

P.O.Box 45 Marayong 2148 Ph 02 9831 5594 Fax 02 9831 3803

The benefits conferred hereunder are in addition to all other rights and remedies in respect of the

product which the purchaser has by virtue of the Trade Practice Act 1974, and similar State and Territory

legislation and nothing contained in this certificate shall in any way limit the purchaser’s rights under such

legislation.

Fiori Holdings Pty Ltd warrants this product against manufacturing defects and faulty materials, for a

period of 24 months from date of purchase.

This warranty is limited to the repair or replacement free of charge within the warranty period of any

component or part which Fiori Holdings Pty Ltd at its discretion determines to be faulty. Such warranty is

subject to the terms and conditions set out below.

TERMS AND CONDITIONS

The following conditions apply in respect of the warranty given in this certificate,

1. The warranty applies within the Commonwealth of Australia and only if the product is used for domestic

purposes and where normal vehicular access is provided.

2. The warranty does not apply for the following:

(a) Light globes

(b) To paint finishes and glass

faulty electrical conection

(d) If the product has been repaired or serviced by an unauthorised person

(e) If installed contrary to Fiori Holdings Pty Ltd instructions

3. For warranty service outside of Capital City metropolitan area or outside the normal service area of

the nearest authorized service provider the purchaser shall be liable for travelling expenses and cost

of transport of the product or parts to and from the Service Agent. NOTE: A charge shall be made if the

service person finds the product is functioning correctly.

4. The purchaser must produce proof of the date of purchase toghether with this Warranty Certificate

when making claim.

5. To abide by the guarantee please complete the details below and keep with your purchase invoice.

For details of your nearest Service Provider please select from the Service Provider list or contact the

warranty administrator, data Works Administration on 02 9674 2361

--------------------------------------------------------------------------------------------------------------------------------------------

Guarantee Record

Name of Purchaser:

Address:

Date of Purchase: Model No: Serial No:

Name of Supplier:

Address:

Invoice No:

Complete but do not post

FIORI Service Providers

State Service Area Company Address City P/C Fax Phone

ACT Canberra Absolute Appliance

Service

3/125 LySaght St Mitchell 2911 (02) 6262-3802 (02) 6262-4272

NSW Albury/

Wodonga

Gj & PJ Yensch Lot 5 Jelbert Rd Jindera 2642 (02) 6026-3178 (02) 6026-3414

NSW Ballina to Tweed Paul N Rogers Lot 4 Stock Route

Yelgun 2483 (02) 6680-3453 (02) 6680-3247

NSW Bathurst Zylstra Appliances 47 Opperman Way Bathurst 2795 (02) 6332-1226 (02) 6332-1226

NSW Bowral Highland Electrical Lot 1 Argyle Lane Bowral 2576 (02) 4861-2424 (02) 4861-4339

NSW Cessnock Coalfields Home

Appliance Service

Centre

173 Vincent St Cessnock 2325 (02) 4990-6757 (02) 4990-6757

NSW Coffs Harbour Co ff s Electrical

Services

5/1 Cook Drive Coffs Harbour 2450 (02) 6651-2273 (02) 6651-4145

NSW Coffs Harbour Reg Wooderson

Appliance Service

P/L

3/36 Holberts Rd Toormina 2452 (02) 6653-3581 (02) 6653-3581

NSW Cowra Neil Stephenson

Washer &

Dishwasher

Service

5 Duncowan St Cowra 2794 (02) 6342-1860 (02) 6342-1860

NSW Dalgety B e r r i d a l e

Appliances

Waterford Park Dalgety 2628 (02) 6456-5234 (04) 2711-0247

NSW Deniliquin I D Appliance

Service

254 Henry St Deniliquin 2710 (03) 5881-6900 (03) 5881-5186

NSW Forster Germon Electrics Bay 5 / lot 7 Kularoo

Drive

Forster 2428 (02) 6555-6694 (02) 6554-8538

NSW Forster/Taree Great Lakes

Appliances

1/6 Commerce

Court

Forster 2428 (02) 6555-6550 (02) 6554-9766

NSW Gloucester Buckets Way

Electrical P/L

22 Church St Gloucester 2422 (02) 6558-2361 (02) 6558-1503

NSW Gosford Rob Moffat

Appliance Repairs

12 Melbourne St East Gosford 2250 (02) 4323-6113 (02) 4323-1163

NSW Grafton Repairs and

Spares

140 Fitzroy St Grafton 2460 (02) 6643-3691 (02) 6642-1911

NSW Griffiths W ade Service

Centre

132 Yambil St Griffiths 2680 (02) 6964-1937 (02) 6962-3932

NSW Hawks Nest DJ & JG Peters 7 Yamba Street Hawks Nest 2324 (02) 4997-1233 (02) 4997-1233

NSW Kempsy Macleay Appliance

Service

1 Verge Lane Kempsy 2440 (02) 6562-1721 (02) 6562-1359

NSW Leeton Leeton Appliance

Service

99 Grevilla St Leeton 2705 (02) 6953-4151 (02) 6953-4151

NSW Merimbula Merrimbula Appli-

ance Service

5 martins Lane Pambula 2458 (02) 6494-3145 (02) 6495-1539

NSW Narooma Gross’s Appliance

Service

42 Old South

Coast Rd

Narooma 2546 (02) 4476-4406 (02) 4476-4447

State Service Area Company Address City P/C Fax Phone

NSW Newcastle H.L.Mullane &

Sons P/L

16 Old Maitland Rd Sandgate 2304 (02) 4960-8933 (02) 4960-8999

NSW Nowra Shoalhaven Gas

Hot Water & Ele-

ments P/L

218 Princess Hwy South Nowra 2541 02 4423 1540 (02) 4423-1533

NSW Orange A and All Electrical

Services

59 Lords Pl Orange 2800 (02) 6362-9344 (02) 6361-3533

NSW Orange Orange Refrigera-

tion and Washing

machine Repairs

159 Peisley St Orange 2800 (02) 6362-9344 (02) 6362-9364

NSW Port Macquarie Mid Coast Appli-

ance Service

“Shop 12, Shores

Retail Centre

Bay St”

Port Mac-

quarie

2444 (02) 6584-2441 (02) 6584-2433

NSW Singleton Electrical Spares

and Repairs

1 Pitt St Singleton 2330 (02) 6572-2755 (02) 6571-1633

NSW Sydney Data Works Admin-

istration

PO Box 785 Kings Langley 2147 02 9674 2415 02 9674 2361

NSW Tamworth Tamworth Electri-

cal Service

214 Bridge St Tamworth 2340 (02) 6765-3589 (02) 6765-8509

NSW Ulladulla Kings Point Appli-

ance Repairs

38 Edward St Kings Point 2539 (02) 4454-0560 (02) 4455-4878

NSW Wagga Wagga B & W Appliance

Service

2/7 Copland St Wagga

Wagga

2650 (02) 6921-1067 (02) 6921-1025

NSW Wollongong Henk’s Appliance

Service

149 Laver Rd Dapto 2530 (02) 4261-9307 (02) 4261-3227

NSW Wollongong Regional Appliance

and Electrical

Services P/L

67 Princes Hwy Fairy Meadow 2519 (02) 4285-9873 (02) 4284-9873

NSW Yass Mark Garland Ap-

pliance Service

7 Hovell St Yass 2582 02 622 628 73 (02) 6226-2873

NT Darwin Mobile Electrics 11 Goyder Rd Darwin 0801 (08) 8941-1217 (08) 8936-1888

QLD Ayr Coral Coast

Electrical

133a Edward St Ayr 4807 (07) 4783-4835 (07) 4783-4711

QLD Brisbane Endeavour Refrig-

eration

167 Robertson St Fortitude

Valley

4006 (07) 3852-2465 (07) 3872-7444

QLD Bundaberg Bundaberg Appli-

ance Service

1 Tomlinson St Bundaberg 4670 (07) 4153-2466 (07) 4153-1700

QLD Glasshouse

Mountains

Jeff Brown Electri-

cal, Ref and A/C

P O Box 318 Glasshouse

Mountains

4518 (07) 5438-7344 (07) 5438-7333

QLD Gympie Deens Electrical 11 Stewart Tce Gympie 4570 (07) 5482-8204 (07) 5482-2366

QLD Hervey Bay Hervey Bay Home

Appliances

90 Dayman St Urangan 4655 (07) 4125-3374 (07) 4125-3775

QLD Mt Isa P & R Electrical 31 Arline St Mt Isa 4825 (07) 4743-6766 (07) 4743-3354

QLD Mt Tambourine Tambourine

Mountain Electrical

Service & Refrig-

eration

Shop 4 Tambourine

Plaza

North Tam-

bourine

4272 (07) 5545-2066 (07) 5545-1207

QLD Nambour Nambour Electrical

Service

60 Price St Nambour 4560 (07) 5441-6113 (07) 5441-1677

QLD Noosa Paul Matters

Electrical P/L

4 Venture Dr Nossaville 4566 (07) 5449-9045 (07) 5449-7133

QLD Pt Douglas Port Douglas

Electric

Lot 1 Captain Cook

Hwy

Craieue 4871 (07) 4098-5944 (07) (40985) 933

QLD Rockhampton Leenders Electrical 13 Murray st Rockhampton 4700 (07) 4927-1187 (07) 4927-2922

For all enquiries please contact the warranty administrator. Ph: 02 9674 2361

Data Works Administration, PO Box 785. Kings Langley. 2147 Fx: 02 9674 2415

[email protected]

State Service Area Company Address City P/C Fax Phone

QLD Sunshine Coast Kerr’s Electrical

Appliance Service

11 Newing Way Caloundra 4551 (07) 5491-7919 (07) 5491-2188

QLD Toowoomba Mercer and Luck 49 Stephen St Toowoomba 4350 (07) 4639-2134 (07) 4632-8155

VIC Bairnsdale Megals 76 McLeod St Bairnsdale 3875 (03) 5152-6101 (03) 5152-4894

VIC Bendigo Charltons 60 to 62 Mundy St Bendigo 3550 (03) 5441-3513 (03) 5443-4622

Vic Colac Keith Walsh

Electrical & Refrig-

eration

216 Murray St Colac 3250 (03) 5232-1297 (03) 5231-4994

VIC Echuca Stapleton Electrical

& Refrigeration

Service

40 McMillan Rd Echuca 3564 (03) 5482-5255 (03) 5482-5453

VIC Geelong Graeme Kent

Elect App Service

27 Elizabeth St Geelong West 3218 (03) 5223-2856 (03) 5221-6588

VIC Horsham J.D & J.M English 56 Mc Pherson St Horsham 3400 (03) 5382-3924 (03) 5382-2568

Vic Melbourne

Metro East side

Northern Home

Appliances

324 Waverley Rd Malvern East 3145 (03) 9572-0401 (03) 9572-0400

VIC Melbourne Nth

West side

Stindl Home Appli-

ance Service

71A Hotham Rd Niddrie 3042 (03) 9379-3627 (03) 9374-1129

Vic Mildura Jack Abel 2-4 Tenth St Mildura 3500 (03) 5023-3598 (03) 5023-3613

VIC Mildura Sunrasia Gas P/L 80 Pine Ave Mildura 3500 03 5021 1716 (03) 5023-2907

VIC Orbost KR & JM Grenfell Cnr Princess

Highway and

Salisbury St

Orbost 3888 (03) 5154-3074 (03) 5154-1092

VIC Ouyen Greegs Electrical 58 to 62 Oke St Ouyen 3490 (03) 5092-2009 (03) 5092-1352

VIC Sale Mackay and Love

Appliance repairs

Rear 216 Raymond

Sale 3850 (03) 5144-7855 (03) 5144-7855

VIC Torquay P.K.E. Appliance

Repairs

18- 20 Bristol Rd Torquay 3228 (03) 5261-5246 (03) 5261-3628

VIC Wangaratta Wohlers & York 48 Norton St Wangaratta 3677 (03) 5721-4595 (03) 5721-2465

VIC Warrnambool Peter Pierson Gas

Services

11 Cockman St Warrnambool 3280 (03) 5561-2182 (03) 5562-5113

The manufacturing ﬁ rm refuses all responsibility for any possible imprecision in this booklet, due to

misprints or clerical errors. It reserves the right to make all the changes that it will consider

necessary in its own products, without affecting the essential characteristics of functionality and safety.

Fiori P44W Instructions And Advice For The Use, Installation And Maintenance

Brand: Fiori

Model: P44W

Category: Hobs

Type: Instructions And Advice For The Use, Installation And Maintenance

This manual is also suitable for

Download PDF

report

Fiori P44W Instructions And Advice For The Use, Installation And Maintenance

This manual is also suitable for

Fiori P44W Instructions And Advice For The Use, Installation And Maintenance

Other documents