Fagor CNC 8058elite T Owner's manual

Type
Owner's manual

This manual is also suitable for

Ref. 2005
8060
8065
Quercus
Examples manual (·T· model).
BLANK PAGE
·2·
MACHINE SAFETY
It is up to the machine manufacturer to make sure that the safety of the machine
is enabled in order to prevent personal injury and damage to the CNC or to the
products connected to it. On start-up and while validating CNC parameters, it
checks the status of the following safety elements. If any of them is disabled, the
CNC shows the following warning message.
Feedback alarm for analog axes.
Software limits for analog and sercos linear axes.
Following error monitoring for analog and sercos axes (except the spindle)
both at the CNC and at the drives.
Tendency test on analog axes.
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC resulting from any of the safety
elements being disabled.
DUAL-USE PRODUCTS
Products manufactured by FAGOR AUTOMATION since April 1st 2014 will
include "-MDU" in their identification if they are included on the list of dual-use
products according to regulation UE 428/2009 and require an export license
depending on destination.
TRANSLATION OF THE ORIGINAL MANUAL
This manual is a translation of the original manual. This manual, as well as the
documents derived from it, have been drafted in Spanish. In the event of any
contradictions between the document in Spanish and its translations, the wording
in the Spanish version shall prevail. The original manual will be labeled with the
text "ORIGINAL MANUAL".
HARDWARE EXPANSIONS
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC resulting from any hardware
manipulation by personnel unauthorized by Fagor Automation.
If the CNC hardware is modified by personnel unauthorized by Fagor
Automation, it will no longer be under warranty.
COMPUTER VIRUSES
FAGOR AUTOMATION guarantees that the software installed contains no
computer viruses. It is up to the user to keep the unit virus free in order to
guarantee its proper operation. Computer viruses at the CNC may cause it to
malfunction.
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC due a computer virus in the
system.
If a computer virus is found in the system, the unit will no longer be under warranty.
All rights reserved. No part of this documentation may be transmitted,
transcribed, stored in a backup device or translated into another language
without Fagor Automation’s consent. Unauthorized copying or distributing of this
software is prohibited.
The information described in this manual may be subject to changes due to
technical modifications. Fagor Automation reserves the right to change the
contents of this manual without prior notice.
All the trade marks appearing in the manual belong to the corresponding owners.
The use of these marks by third parties for their own purpose could violate the
rights of the owners.
It is possible that CNC can execute more functions than those described in its
associated documentation; however, Fagor Automation does not guarantee the
validity of those applications. Therefore, except under the express permission
from Fagor Automation, any CNC application that is not described in the
documentation must be considered as "impossible". In any case, Fagor
Automation shall not be held responsible for any personal injuries or physical
damage caused or suffered by the CNC if it is used in any way other than as
explained in the related documentation.
The content of this manual and its validity for the product described here has been
verified. Even so, involuntary errors are possible, hence no absolute match is
guaranteed. However, the contents of this document are regularly checked and
updated implementing the necessary corrections in a later edition. We appreciate
your suggestions for improvement.
The examples described in this manual are for learning purposes. Before using
them in industrial applications, they must be properly adapted making sure that
the safety regulations are fully met.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
·3·
REF. 2005
INDEX
CHAPTER 1 BASIC CONCEPTS.
1.1 Basic CNC operating concepts ........................................................................................ 6
1.2 Tools used in the examples. ............................................................................................ 8
1.3 Set part zero. ................................................................................................................... 9
1.4 Programming of the machining conditions..................................................................... 11
1.5 Programming coordinates.............................................................................................. 12
1.5.1 Example. Absolute and incremental coordinates. ...................................................... 13
1.6 Tool path programming.................................................................................................. 14
1.6.1 Example. Arc programming "G02/G03". .................................................................... 15
1.6.2 Example. Tangential entry/exit "G37/G38" and corner rounding (radius blend) "G36". .
17
CHAPTER 2 CANNED CYCLE PROGRAMMING.
2.1 Introduction .................................................................................................................... 19
2.2 Example. Inside turning of curved and straight sections................................................ 20
2.3 Example. Facing of inside curved sections and outside straight sections. .................... 22
2.4 Example. Facing of inside straight sections and outside curved sections. .................... 24
2.5 Example. Inside roughing along Z axis and outside turning of curved sections. ........... 26
2.6 Example. Inside turning of straight sections and outside roughing along the Z axis. .... 28
2.7 Example. Inside and outside roughing along the X axis. ............................................... 30
2.8 Example. Inside and outside taper threading................................................................. 32
2.9 Example. Roughing on the X axis. Outside grooving and threading.............................. 34
2.10 Example. Outside pattern repeat. Internal grooving and threading. .............................. 37
2.11 Example. Inside and outside roughing along the X axis. ............................................... 40
CHAPTER 3 C AXIS PROGRAMMING
3.1 Introduction. ................................................................................................................... 43
3.2 Example. Machining of a profile in the ZC plane. .......................................................... 45
3.3 Example. Machining of a profile in the XC plane. .......................................................... 47
CHAPTER 4 PROFILE EDITOR
4.1 Example. Profile editor................................................................................................... 50
4.2 Example. Profile editor................................................................................................... 51
4.3 Example. Profile editor................................................................................................... 52
4.4 Example. Profile editor................................................................................................... 53
CHAPTER 5 USE SUBROUTINES TO CREATE CANNED CYCLES.
5.1 Arithmetic subroutines and parameters. ........................................................................ 55
5.2 Assistance for subroutines............................................................................................. 57
5.2.1 Subroutine help files................................................................................................... 57
5.3 Example: Global subroutine. Machining of pulleys. ....................................................... 58
5.3.1 Define the subroutine. ................................................................................................ 58
5.3.2 Call to the subroutine from the part-program. ............................................................ 61
BLANK PAGE
·4·
Quercus
CNC 8060
CNC 8065
1
·5·
REF. 2005
1. BASIC CONCEPTS.
Purpose of the exercises.
The purpose of the following programming examples is to familiarize with editing, simulating
and executing programs. Machining starts with raw piece that after running various
operations and cycles on it, it becomes the finished part, programming also the relevant
machining conditions as well as the tools to be used.
The feedrate and spindle speed values are only illustrative and depend on the material of
the part and the tool being used. When using the examples of this manual to make real parts
(on a machine), the feedrate and spindle speed values must be adapted properly.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Basic CNC operating concepts
·6·
REF. 2005
1.1 Basic CNC operating concepts
Some useful keys.
Some operating modes.
Execution keys.
Editing a program.
To select a program from the list:
1 Select the folder that contains the program. If it is a new program, it will be saved in this
folder.
2 Select the program from the list or write its name in the bottom window. To edit a new
program, write the name of the program in the lower window and the CNC will open an
empty program or a predefined template depending on how the editor is configured.
3 Press [ENTER] to accept the selection and open the program or [ESC] to cancel it and
close the program listing.
Syntax check.
The CNC analyzes each program block while editing. If the CNC detects a syntax error in
the block, the error window at the bottom of the screen will display it.
Key. Function.
Automatic mode.
Execute a part-program in "single block" or "automatic" mode.
EDISIMU mode.
Edit and simulate the execution of a part-program displaying a graphic representation of
the program being simulated.
User tables (zero offsets, fixtures and arithmetic parameters).
Tool and magazine table.
Key. Function.
Cycle start key (START).
Execute the selected program in automatic mode, a block in MDI/MDA mode, etc.
Cycle stop key (STOP).
Interrupt the execution of the CNC.
Reset key.
It initializes the system setting the initial conditions as defined by machine parameters.
Single-block execution mode.
AUTO
EDIT
TABLES
TOOLS
RESET
SINGLE
Programs are edited in the EDISIMU mode. Once in this mode, the "Open program" softkey
may be used to select the program to be edited which may be either a new one or an existing
one. When selecting this option, the CNC shows a list of the available programs.
EDIT
The entire program can also be checked. To do that, press the vertical softkey for syntax
check. The errors found will be indicated like with the other method.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Basic CNC operating concepts
·7·
REF. 2005
Program simulation.
The program simulation procedure is the following:
1 Choose the type of graphic representation, its dimensions and the point of view. This data
may also be modified during the simulation of the program.
The simulation of the program starts at the first block of the program and ends after executing
one of the end-of-program functions "M02" or "M30". As an option, it is possible to define
the first and last blocks of the simulation.
2 Activate the desired simulation options using the softkey menu.
3 Pressing the [START] softkey begins the simulation of the program that is being edited.
The simulation may be interrupted with the [STOP] softkey or canceled with the [RESET]
softkey.
START STOP RESET
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Tools used in the examples.
·8·
REF. 2005
1.2 Tools used in the examples.
Tool Geometry Data Tool Geometry Data
T2 D:
F:
A:
B:
C:
Lc:
Rp:
1
3
60
o
7 mm.
100
o
6 mm.
0.4 mm.
T3 D:
F:
A:
B:
C:
Lc:
Rp:
1
2
60
o
7 mm.
60
o
6 mm.
0.2 mm.
T4 D:
F:
A:
B:
C:
Lc:
Rp:
1
3
30
o
7 mm.
100
o
6 mm.
0.4 mm.
T8 D:
F:
A:
B:
C:
Lc:
Rp:
1
5
60
o
7,5 mm.
100
o
6 mm.
0.4 mm.
T9 D:
L:
R:
Lc:
Rp:
1
100 mm.
10 mm.
10 mm.
0 mm.
T10 D:
F:
A:
B:
C:
Lc:
Rp:
1
5
50
o
5 mm.
65
o
5 mm.
0.1 mm.
T11 D:
F:
A:
B:
C:
Lc:
Rp:
1
2
50
o
5 mm.
65
o
5 mm.
0.1 mm.
T12 D:
F:
A:
B:
C:
Lc:
Rp:
1
3
90
o
4 mm.
90
o
4 mm.
0 mm.
T13 D:
F:
A:
B:
C:
Lc:
Rp:
1
6
90
o
4 mm.
90
o
4 mm.
0 mm.
T15 D:
L:
R:
Lc:
Rp:
1
40 mm.
5 mm.
10 mm.
0 mm.
T16 D:
L:
R:
Lc:
Rp:
1
40 mm.
5 mm.
5 mm.
0 mm.
T17 D:
F:
A:
B:
C:
Lc:
Rp:
1
2
40
o
7 mm.
70
o
6 mm.
0.2 mm.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Set part zero.
·9·
REF. 2005
1.3 Set part zero.
With this CNC, it is possible to program movements in the machine reference system or apply
offsets in order to use reference systems referred to the fixtures or the part without having
to change the coordinates of the different points of the part in the program.
The part zero must be located so as to make programming easier. If no part zero is set, the
coordinates will be referred to the machine reference system.
Coordinate preset (G92).
When presetting a coordinate, the CNC interprets that the axis coordinates programmed
after the G92 set the current position of the axes. The rest of the axes that have not been
defined with G92 are not affected by the preset.
Zero offsets (G54-G59/G159).
Using zero offsets, it is possible to place the part zero in different positions of the machine.
When applying a zero offset, the CNC assumes as the new part zero the point defined by
the selected zero offset.
In order to apply a zero offset, it must have been previously defined. To do that, the CNC
has a table where the operator may define up to 99 different zero offsets. The table data may
be defined:
Manually from the CNC's front panel (as described in the Operating Manual).
By program, assigning the corresponding value (of the "n" offset and of the "Xn" axis)
to the "V.A.ORGT[n].Xn" variable.
Once the zero offsets have been defined in the table, they may be activated via program by
programming function G59 followed by the offset number to be activated. The first six zero
offsets of the table can also be applied using functions G54 through G59; G54 for the first
one (same as G159=1), G55 for the second one (same as G159=2) and so on.
G90 G00 X32 Z120 ; Tool approach
G01 X0 ; Facing and positioning in (120,0)
G92 X0 Y0 ;Presetting (120,0) as part zero
Y
X
70
10
30
20
50
120
Ow
Ow
Ow
G54
G55
G56
P1
O
M
X Y
G54 (G159=1)
20 70
G55 (G159=2)
50 30
G56 (G159=3)
120 10
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Set part zero.
·10·
REF. 2005
Cancellation of the part zero (G53).
The part zero stays active until it is canceled with a preset, a zero offset or with a "G53".
N 1 0 0 V. A . O R GT [ 1 ]. X = 2 0 V. A . O R G T [ 1 ] . Y = 7 0
N 1 1 0 V. A . O R GT [ 2 ]. X = 5 0 V. A . O R G T [ 2 ] . Y = 3 0
N100 V.A.ORGT[3].X=120 V.A.ORGT[3].Y=10
...
N100 G54
(It applies the first zero offset)
N200 G159=2
(It applies the second zero offset)
N300 G56 X20 Y30
(It applies the third zero offset)
(The axes move to point X20 Y30 (point P1) referred to the third origin)
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Programming of the machining conditions.
·11·
REF. 2005
1.4 Programming of the machining conditions.
Feedrate programming units (G94/G95).
G94 Feedrate in millimeters/minute (inches/minute).
The feedrate is independent from the spindle speed.
G95 Feedrate in millimeters/revolution (inches/revolution).
The feedrate changes with the spindle speed (usual operation on lathes).
By default the type of feedrate is set in machine parameter IFEED.
Speed programming units (G96/G97).
G96 Constant surface speed.
The G96 function only affects the master spindle of the channel. At constant surface
speed, the CNC changes the spindle speed as the perpendicular axis moves in order
to maintain the cutting speed constant between the tool and the part, thus optimizing
the machining conditions. When working at constant surface speed, it is
recommended to limit by program the maximum turning speed that the spindle can
reach.
G97 Constant turning speed.
Turning speed limit
Function G192 limits the spindle turning speed in both work modes; G96 and G97. This
function is especially useful when working at constant cutting speed while machining large
parts or when doing spindle maintenance work. If function G192 is not programmed, the
turning speed is limited by machine parameter G00FEED of the gear.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Programming coordinates.
·12·
REF. 2005
1.5 Programming coordinates.
Absolute (G90) or incremental (G91) coordinates.
G90 Programming in absolute coordinates. The coordinates of the point are referred to
the current origin of the coordinate system, usually the part zero.
G91 Programming in incremental coordinates. The coordinates of the point are referred
to the current tool position.
By default the type of feedrate is set in machine parameter ISYSTEM.
Programming in radius (G152) or in diameters (G151).
Programming in diameters is only available on the axes allowed by the machine
manufacturer (DIAMPROG=YES).
G151 Programming in diameters.
G152 Programming in radius.
N10 G00 G71 G90 Z0 X0
N20 G01 Z35 X55 F450
N30 Z75 X25
N40 X0 Z0
N50 M30
N10 G00 G71 G90 Z0 X0
N20 G01 G91 Z35 X55 F450
N30 Z40 X-30
N40 Z-75 X-25
N50 M30
Programming in radius. Programming in diameters.
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Programming coordinates.
·13·
REF. 2005
1.5.1 Example. Absolute and incremental coordinates.
Programming in radius.
Programming in diameters.
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4 M41
G0 X50 Z100
G1 X0 Z80 ; Point A
G1 X15 Z65 ; A-B section
Z55 ; B-C section
X40 Z30 ; C-D section
Z0 ; D-E section
G0 X50 Z100
M30
G90 G95 G96 F0.15 S180 T2 D1 M4 M41
G0 X50 Z100
G1 X0 Z80 ; Point A
G1 G91 X15 Z-15 ; A-B section
Z-10 ; B-C section
X25 Z-25 ; C-D section
Z-30 ; D-E section
G0 G90 X50 Z100
M30
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4 M41
G0 X100 Z100
G1 X0 Z80 ; Point A
G1 X30 Z65 ; A-B section
Z55 ; B-C section
X80 Z30 ; C-D section
Z0 ; D-E section
G0 X100 Z100
M30
G90 G95 G96 F0.15 S180 T2 D1 M4 M41
G0 X100 Z100
G1 X0 Z80 ; Point A
G1 G91 X30 Z-15 ; A-B section
Z-10 ; B-C section
X50 Z-25 ; C-D section
Z-30 ; D-E section
G0 G90 X100 Z100
M30
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Tool path programming
·14·
REF. 2005
1.6 Tool path programming
G00 Rapid traverse.
G01 Linear interpolation.
G02 Clockwise circular interpolation.
G03 Counterclockwise circular interpolation.
Functions G02/G03 offer two ways of programming in Cartesian coordinates.
G36 Corner rounding, radius blend.
The programming format is "G36 I–" where "I" is the radius. Parameter I is valid for
all four functions G36, G37, G38 and G39 and stays active until a new value is
programmed.
G37 Tangential entry.
The programming format is "G37 I–" where "I" is the radius.
G38 Tangential exit.
The programming format is "G38 I–" where "I" is the radius.
G39 Corner chamfering.
The programming format is "G39 I–" where "I" is the size of the chamfer.
G40 Cancellation of tool radius compensation.
G41 Left-hand tool radius compensation.
G42 Right-hand tool radius compensation.
The tool will position to the left or to the right of the programmed path, according to
the machining direction.
Setting the end point and the radius. Setting the end point and the center.
G02/G03 X Z R G02/G03 X Z I K
Sign of the radius.
Arc 1: G02 X... Z... R-...
Arc 2: G02 X... Z... R+...
Arc 3: G03 X... Z... R+...
Arc 4: G03 X... Z... R-...
Without compensation. With compensation.
Z
X
R
X,Z
Z
X
I
K
X,Z
Z
X
1
2
3
4
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Tool path programming
·15·
REF. 2005
1.6.1 Example. Arc programming "G02/G03".
Programming in radius.
Programming with the arc center.
Programming with the arc center.
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X60 Z120
G1 X0 Z90 ; Point A
G3 X20 Z70 I0 K-20 ; A-B section
G1 Z60 ; B-C section
G2 X30 Z30 I50 K0 ; C-D section
G1 X40 ; D-E section
G3 X50 Z10 I-19.9 K-22.45 ; E-F section
G1 Z0 ; F-G section
G0 X60 Z120
M30
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X60 Z120
G1 X0 Z90; Point A
G91 G3 X20 Z-20 I0 K-20 ; A-B section
G1 Z-10 ; B-C section
G2 X10 Z-30 I50 K0 ; C-D section
G1 X10 ; D-E section
G3 X10 Z-20 I-19.9 K-22.45 ; E-F section
G1 Z-10 ; F-G section
G0 G90 X60 Z120
M30
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X60 Z120
G1 X0 Z90 ; Point A
G3 X20 Z70 R20 ; A-B section
G1 Z60 ; B-C section
G2 X30 Z30 R50 ; C-D section
G1 X40 ; D-E section
G3 X50 Z10 R30 ; E-F section
G1 Z0 ; F-G section
G0 X60 Z120
M30
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X60 Z120
G1 X0 Z90 ; Point A
G91 G3 X20 Z-20 R20 ; A-B section
G1 Z-10 ; B-C section
G2 X10 Z-30 R50 ; C-D section
G1 X10 ; D-E section
G3 X10 Z-20 R30 ; E-F section
G1 Z-10 ; F-G section
G0 G90 X60 Z120
M30
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Tool path programming
·16·
REF. 2005
Programming in diameters.
Programming with the arc center.
Programming with the arc center.
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X120 Z120
G1 X0 Z90 ; Point A
G3 X40 Z70 I0 K-20 ; A-B section
G1 Z60 ; B-C section
G2 X60 Z30 I50 K0 ; C-D section
G1 X80 ; D-E section
G3 X100 Z10 I-19.9 K-22.45 ; E-F section
G1 Z0 ; F-G section
G0 X120 Z120
M30
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X120 Z120
G1 X0 Z90 ; Point A
G91 G3 X40 Z-20 I0 K-20 ; A-B section
G1 Z-10 ; B-C section
G2 X20 Z-30 I50 K0 ; C-D section
G1 X20 ; D-E section
G3 X20 Z-20 I-19.9 K-22.45 ; E-F section
G1 Z-10 ; F-G section
G0 G90 X120 Z120
M30
Absolute coordinates (G90). Incremental coordinates (G91).
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X120 Z120
G1 X0 Z90 ; Point A
G3 X40 Z70 R20 ; A-B section
G1 Z60 ; B-C section
G2 X60 Z30 R50 ; C-D section
G1 X80 ; D-E section
G3 X100 Z10 R30 ; E-F section
G1 Z0 ; F-G section
G0 X120 Z120
M30
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X120 Z120
G1 X0 Z90 ; Point A
G91 G3 X40 Z-20 R20 ; A-B section
G1 Z-10 ; B-C section
G2 X20 Z-30 R50 ; C-D section
G1 X20 ; D-E section
G3 X20 Z-20 R30 ; E-F section
G1 Z-10 ; F-G section
G0 G90 X120 Z120
M30
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
BASIC CONCEPTS.
1.
Tool path programming
·17·
REF. 2005
1.6.2 Example. Tangential entry/exit "G37/G38" and corner rounding (radius
blend) "G36".
Programming with the arc center.
Absolute coordinates (G90).
G90 G95 G96 F0.15 S180 T2 D1 M4
G0 X120 Z120
G42 X0 ; Begin tool radius compensation.
G01 X0 Z100
G37 I4 ; Tangential entry at point A.
G01 X40 ; A-B section
G36 I5 ; Rounding B
G01 Z70 ; B-C section
G36 ; Rounding C (I radius stays active)
G01 X60 Z50 ; C-D section
G36 ; Rounding D
G01 X80 ; D-E section
G36 ; Rounding E
G01 Z30 ; E-F section
G36 ; Rounding F
G01 X100 Z20 ; F-G section
G36 ; Rounding G
G01 Z0 ; G-H section
G38 I4 ; Tangential exit.
G0 X120
G40 Z120 ; End of tool radius compensation.
M30
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
1.
BASIC CONCEPTS.
Tool path programming
·18·
REF. 2005
Quercus
CNC 8060
CNC 8065
2
·19·
REF. 2005
2. CANNED CYCLE PROGRAMMING.
2.1 Introduction
The canned cycles edited in ISO code are defined using a "G" function and its relevant
parameters.
G81 Turning cycle with straight sections.
G82 Facing cycle with straight sections.
G83 Drilling / tapping canned cycle.
G84 Turning cycle with circular sections.
G85 Facing cycle with circular sections.
G86 Longitudinal threading.
G87 Face threading.
G88 Grooving cycle along X axis.
G89 Grooving cycle along Z axis.
G66 Pattern repeat cycle.
G68 Stock removal along the X axis.
G69 Stock removal along the Z axis.
Machining canned cycles with a live tool:
G160 Drilling / tapping canned cycle on the face of the part.
G161 Drilling / tapping canned cycle on the side of the part.
G162 Slot milling canned cycle along the side of the part.
G163 Slot milling canned cycle along the face of the part.
A canned cycle may be defined anywhere in the program, that is, in the main program as
well as in a subroutine.
When working in a plane other than the ZX, the CNC interprets the canned cycle parameters
as follows:
Parameter Z-X plane W-X plane A-B plane
Parameter Z and all related to it, with the abscissa
axis
Z axis W axis A axis
Parameter X and all related to it, with the ordinate
axis
X axis X axis B axis
Examples manual (·T· model).
Quercus
CNC 8060
CNC 8065
2.
CANNED CYCLE PROGRAMMING.
Example. Inside turning of curved and straight sections.
·20·
REF. 2005
2.2 Example. Inside turning of curved and straight sections.
; First fixture.
; Set part zero:
; Operation 1 (Drilling)
; Operation 2 (Inside curved turning)
; Operation 3 (Facing and outside turning)
Raw dimensions Ø80x114 mm.
V.A.ORGT[1].X=0 V.A.ORGT[1].Z=112
G54
G192 S2200
G94 G97 F90 S600 M4
G0 Z150
T9 D1
G0 X0 Z8
G83 X0 Z0 I45.773 B9 D4 K0 H0 C1
G95 G96 F0.2 S120 M4
T8 D1
G0 X20 Z20
G1 G41 X18 Z5
G84 X70 Z0 Q20 R-33.541 C2 L0.3 M0.3 H0.1 I-35 K0
G0 G40 Z150
G95 G96 F0.2 S180 M4
T2 D1
G0 X90 Z20
G1 X78 Z5
G1 Z-40
G1 X85
G0 Z0
G1 X66
G1 Z5
G1 G42 X72 Z1
G1 X80 Z-3
G0 G40 Z150
Z
X
1
Z
X
2
Z
X
3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Fagor CNC 8058elite T Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI