Rheem RQPL-B049JK000 Installation guide

Brand: Rheem

Model: RQPL-B049JK000

Type: Installation guide

This manual is also suitable for

PACKAGE HEAT PUMPS FEATURING

INDUSTRY STANDARD R-410A REFRIGERANT

RQNL- 13 SEER SERIES (2-4 TONS)

RQPL- 14 SEER SERIES (2-4 TONS)

92-20522-42-08

SUPERSEDES 92-20522-42-07

INSTALLATION INSTRUCTIONS

14 SEER ONLY

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO

QUALIFIED, LICENSED SERVICE PERSONNEL FOR

PROPER INSTALLATION, ADJUSTMENT AND OPERATION

OF THIS UNIT. READ THESE INSTRUCTIONS THOROUGHLY

BEFORE ATTEMPTING INSTALLATION OR OPERATION.

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT

IN IMPROPER INSTALLATION, ADJUSTMENT, SERVICE OR

MAINTENANCE POSSIBLY RESULTING IN FIRE, ELECTRICAL

SHOCK, PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

WARNING

ISO 9001:2008

TABLE OF CONTENTS

I. Safety Information.................................................................................................3

II. Introduction ...........................................................................................................5

A. R-410A Refrigerant...........................................................................................5

1. Specification of R-410A.................................................................................5

2. Quick Reference for R-410A.........................................................................5

3. Evaporator Coil/TXV .....................................................................................5

4. Tools Required for Installing and Servicing R-410A Models.........................5

III. Checking Product Received..................................................................................8

IV. Equipment Protection............................................................................................8

V. Installation.............................................................................................................8

A. General .............................................................................................................8

1. Pre-Installation Check Points........................................................................8

2. Location.........................................................................................................8

B. Outside Slab Installation..................................................................................10

C.Clearances ......................................................................................................10

D.Rooftop Installation..........................................................................................10

VI. Ductwork.............................................................................................................11

VII. Filters ..................................................................................................................12

VIII. Conversion Procedure ........................................................................................13

IX. Condensate Drain...............................................................................................13

X. Condensate Drain, Outdoor Coil.........................................................................14

XI. Electrical Wiring ..................................................................................................14

A. Power Wiring...................................................................................................14

B. Control Wiring .................................................................................................14

C.Internal Wiring.................................................................................................14

D.Grounding .......................................................................................................14

E. Thermostat......................................................................................................15

XII. Indoor Air Flow Data ...........................................................................................16

XIII. Crankcase Heat ..................................................................................................16

XIV. Pre-Start Check...................................................................................................16

XV. Startup.................................................................................................................16

XVI. Operation ............................................................................................................17

XVII. Auxiliary Heat......................................................................................................17

XVIII. Demand Defrost Control and High/Low Pressure Controls.................................18

XIX. General Data..................................................................................................20-24

XX. Miscellaneous

Electrical Data ................................................................................................25-26

Airflow Performance.......................................................................................27-30

Heater Kit Characteristics...............................................................................31-32

Wiring Diagrams.............................................................................................33-37

Charge Charts................................................................................................38-42

Trouble Shooting .................................................................................................43

WARNING

THE MANUFACTURER’S WARRANTY DOES NOT COVER ANY DAMAGE OR

DEFECT TO THE HEAT PUMP CAUSED BY THE ATTACHMENT OR USE OF ANY

COMPONENTS, ACCESSORIES OR DEVICES (OTHER THAN THOSE AUTHO-

RIZED BY THE MANUFACTURER) INTO, ONTO OR IN CONJUNCTION WITH

THE HEAT PUMP. YOU SHOULD BE AWARE THAT THE USE OF UNAUTHO-

RIZED COMPONENTS, ACCESSORIES OR DEVICES MAY ADVERSELY AFFECT

THE OPERATION OF THE HEAT PUMP AND MAY ALSO ENDANGER LIFE AND

PROPERTY. THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY FOR

SUCH LOSS OR INJURY RESULTING FROM THE USE OF SUCH UNAUTHO-

RIZED COMPONENTS, ACCESSORIES OR DEVICES.

WARNING

DISCONNECT ALL POWER TO THE UNIT BEFORE STARTING MAINTENANCE.

FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK OR DEATH.

WARNING

DO NOT, UNDER ANY CIRCUMSTANCES, CONNECT RETURN DUCTWORK

TO ANY OTHER HEAT PRODUCING DEVICE SUCH AS A FIREPLACE INSERT,

STOVE, ETC. UNAUTHORIZED USE OF SUCH DEVICES MAY RESULT IN FIRE,

CARBON MONOXIDE POISONING, EXPLOSION, PROPERTY DAMAGE,

WARNING

IMPORTANT: ALL MANUFACTURER PRODUCTS MEET CURRENT FEDERAL

OSHA GUIDELINES FOR SAFETY. CALIFORNIA PROPOSITION 65 WARNINGS

ARE REQUIRED FOR CERTAIN PRODUCTS, WHICH ARE NOT COVERED BY

THE OSHA STANDARDS.

CALIFORNIA'S PROPOSITION 65 REQUIRES WARNINGS FOR PRODUCTS

SOLD IN CALIFORNIA THAT CONTAIN, OR PRODUCE, ANY OF OVER 600 LIST-

ED CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER

OR BIRTH DEFECTS SUCH AS FIBERGLASS INSULATION, LEAD IN BRASS,

AND COMBUSTION PRODUCTS FROM NATURAL GAS.

ALL “NEW EQUIPMENT” SHIPPED FOR SALE IN CALIFORNIA WILL HAVE

LABELS STATING THAT THE PRODUCT CONTAINS AND/OR PRODUCES

PROPOSITION 65 CHEMICALS. ALTHOUGH WE HAVE NOT CHANGED OUR

PROCESSES, HAVING THE SAME LABEL ON ALL OUR PRODUCTS FACILI-

TATES MANUFACTURING AND SHIPPING. WE CANNOT ALWAYS KNOW

“WHEN, OR IF” PRODUCTS WILL BE SOLD IN THE CALIFORNIA MARKET.

YOU MAY RECEIVE INQUIRIES FROM CUSTOMERS ABOUT CHEMICALS

FOUND IN, OR PRODUCED BY, SOME OF OUR HEATING AND AIR-CONDITION-

ING EQUIPMENT, OR FOUND IN NATURAL GAS USED WITH SOME OF OUR

PRODUCTS. LISTED BELOW ARE THOSE CHEMICALS AND SUBSTANCES

COMMONLY ASSOCIATED WITH SIMILAR EQUIPMENT IN OUR INDUSTRY AND

OTHER MANUFACTURERS.

• GLASS WOOL (FIBERGLASS) INSULATION

• CARBON MONOXIDE (CO)

• FORMALDEHYDE

• BENZENE

MORE DETAILS ARE AVAILABLE AT THE WEBSITES FOR OSHA

(OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION), AT

WWW.OSHA.GOV

AND THE STATE OF CALIFORNIA'S OEHHA (OFFICE OF

ENVIRONMENTAL HEALTH HAZARD ASSESSMENT), AT WWW.OEHHA.ORG.

CONSUMER EDUCATION IS IMPORTANT SINCE THE CHEMICALS AND SUB-

STANCES ON THE LIST ARE FOUND IN OUR DAILY LIVES. MOST CON-

SUMERS ARE AWARE THAT PRODUCTS PRESENT SAFETY AND HEALTH

RISKS, WHEN IMPROPERLY USED, HANDLED AND MAINTAINED.

I. SAFETY INFORMATION

WARNING

ONLY ELECTRIC HEATER KITS SUPPLIED BY THIS MANUFACTURER AS

DESCRIBED IN THIS PUBLICATION HAVE BEEN DESIGNED, TESTED, AND

EVALUATED BY A NATIONALLY RECOGNIZED SAFETY TESTING AGENCY

FOR USE WITH THIS UNIT. USE OF ANY OTHER MANUFACTURED ELECTRIC

HEATERS INSTALLED WITHIN THIS UNIT MAY CAUSE HAZARDOUS CONDI-

TIONS RESULTING IN PROPERTY DAMAGE, FIRE, BODILY INJURY OR

DEATH.

WARNING

THE UNIT MUST BE PERMANENTLY GROUNDED. A GROUNDING LUG IS

PROVIDED IN THE ELECTRIC HEAT KIT FOR A GROUND WIRE. (SEE FIGURE

10.) FAILURE TO GROUND THIS UNIT CAN RESULT IN FIRE OR ELECTRICAL

SHOCK CAUSING PROPERTY DAMAGE, SEVERE PERSONAL INJURY OR

WARNING

IMPORTANT: ALL MANUFACTUR-

ER PRODUCTS MEET CURRENT

FEDERAL OSHA GUIDELINES FOR

SAFETY. CALIFORNIA

PROPOSITION 65 WARNINGS ARE

REQUIRED FOR CERTAIN PROD-

UCTS, WHICH ARE NOT COVERED

BY THE OSHA STANDARDS.

CALIFORNIA'S PROPOSITION 65

REQUIRES WARNINGS FOR PROD-

UCTS SOLD IN CALIFORNIA THAT

CONTAIN, OR PRODUCE, ANY OF

OVER 600 LISTED CHEMICALS

KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER

OR BIRTH DEFECTS SUCH AS

FIBERGLASS INSULATION, LEAD

IN BRASS, AND COMBUSTION

PRODUCTS FROM NATURAL GAS.

ALL “NEW EQUIPMENT” SHIPPED

FOR SALE IN CALIFORNIA WILL

HAVE LABELS STATING THAT THE

PRODUCT CONTAINS AND/OR

PRODUCES PROPOSITION 65

CHEMICALS. ALTHOUGH WE HAVE

NOT CHANGED OUR PROCESSES,

HAVING THE SAME LABEL ON ALL

OUR PRODUCTS FACILITATES

MANUFACTURING AND SHIPPING.

WE CANNOT ALWAYS KNOW

“WHEN, OR IF” PRODUCTS WILL

BE SOLD IN THE CALIFORNIA

MARKET.

YOU MAY RECEIVE INQUIRIES

FROM CUSTOMERS ABOUT CHEMI-

CALS FOUND IN, OR PRODUCED

BY, SOME OF OUR HEATING AND

AIR-CONDITIONING EQUIPMENT,

OR FOUND IN NATURAL GAS USED

WITH SOME OF OUR PRODUCTS.

LISTED BELOW ARE THOSE CHEM-

ICALS AND SUBSTANCES COM-

MONLY ASSOCIATED WITH SIMI-

LAR EQUIPMENT IN OUR INDUS-

TRY AND OTHER MANUFACTUR-

ERS.

• GLASS WOOL (FIBERGLASS)

INSULATION

• CARBON MONOXIDE (CO)

• FORMALDEHYDE

• BENZENE

MORE DETAILS ARE AVAILABLE

AT THE WEBSITES FOR OSHA

(OCCUPATIONAL SAFETY AND

HEALTH ADMINISTRATION), AT

WWW.OSHA.GOV

AND THE STATE

OF CALIFORNIA'S OEHHA (OFFICE

OF ENVIRONMENTAL HEALTH

HAZARD ASSESSMENT), AT

WWW.OEHHA.ORG. CONSUMER

EDUCATION IS IMPORTANT SINCE

THE CHEMICALS AND SUB-

STANCES ON THE LIST ARE

FOUND IN OUR DAILY LIVES. MOST

CONSUMERS ARE AWARE THAT

PRODUCTS PRESENT SAFETY AND

HEALTH RISKS, WHEN IMPROPER-

LY USED, HANDLED AND MAIN-

TAINED.

Recognize this symbol as an indica-

tion of Important Safety Information!

CAUTION

R-410A systems operate at higher pressures than R-22 systems. Do not use

R-22 service equipment or components on R-410A equipment.

II. INTRODUCTION

This booklet contains the installation and operating instructions for your package heat

pump. There are a few precautions that should be taken to derive maximum satisfaction

from it. Improper installation can result in unsatisfactory operation or dangerous conditions.

Read this booklet and any instructions packaged with separate equipment required to

make up the system prior to installation. Give this booklet to the owner and explain its pro-

visions. The owner should retain this booklet for future reference.

NOTE: A load calculation must be performed to properly determine the required heating

and cooling for the structure. Also, the duct must be properly designed and installed for

proper airflow. Existing ductwork must be inspected for proper size and sealed system.

Proper airflow is necessary for both user comfort and equipment performance.

IMPORTANT: Proper application, installation and maintenance of this equipment is a must

if consumers are to receive the full benefit for which they have paid.

A. R-410A REFRIGERANT

All units are factory charged with R-410A refrigerant.

1. Specification of R-410A:

Application: R-410A is not a drop-in replacement for R-22; equipment designs must

accommodate its higher pressures. It cannot be retrofitted into R-22 units.

Pressure: The pressure of R-410A is approximately 60% (1.6 times) greater than R-

22. Recovery and recycle equipment, pumps, hoses and the like need to have design

pressure ratings appropriate for R-410A. Manifold sets need to range up to 800 psig

high-side and 250 psig low-side with a 550 psig low-side retard. Hoses need to have a

service pressure rating of 800 psig. Recovery cylinders need to have a 400 psig service

pressure rating. DOT 4BA400 or DOT BW400.

Combustibility: At pressures above 1 atmosphere, mixture of R-410A and air can

become combustible. R-410A and air should never be mixed in tanks or supply

lines, or be allowed to accumulate in storage tanks. Leak checking should never

be done with a mixture of R-410A and air. Leak checking can be performed safely

with nitrogen or a mixture of R-410A and nitrogen.

2. Quick Reference Guide For R-410A

• R-410A refrigerant operates at approximately 60% higher pressure (1.6 times) than R-

22. Ensure that servicing equipment is designed to operate with R-410A.

• R-410A refrigerant cylinders are pink.

• R-410A, as with other HFC’s is only compatible with POE oils.

• Vacuum pumps will not remove moisture from POE oil.

• R-410A systems are to be charged with liquid refrigerants. Prior to March 1999, R-

410A refrigerant cylinders had a dip tube. These cylinders should be kept upright for

equipment charging. Post March 1999 cylinders do not have a dip tube and should

be inverted to ensure liquid charging of the equipment.

• Do not install a suction line filter drier in the liquid line.

• A liquid line filter drier is standard on every unit.

• Desiccant (drying agent) must be compatible for POE oils and R-410A

3. Evaporator Coil / TXV

The thermostatic expansion valve is specifically designed to operate with R-410A. DO

NOT use an R-22 TXV. The existing evaporator must be replaced with the factory

specified TXV evaporator specifically designed for R-410A.

4. Tools Required For Installing & Servicing R-410A Models

Manifold Sets:

-Up to 800 PSIG High side

-Up to 250 PSIG Low Side

-550 PSIG Low Side Retard

Manifold Hoses:

-Service Pressure Rating of 800 PSIG

Recovery Cylinders:

-400 PSIG Pressure Rating

-Dept. of Transportation 4BA400 or BW400

FIGURE 1

BLOWER/

EVAPORATOR

ACCESS PANEL

SIDE SUPPLY

DUCT OPENING

OUTDOOR FAN GRILLE

AND COMPRESSOR ACCESS

CONTROL

ACCESS PANEL

LIQUID PRESSURE

SERVICE PORT

SUCTION PRESSURE

SERVICE PORT

OUTDOOR COIL

PROTECTIVE GRILLE

FILTER ACCESS

PANEL (FOR

UNIT MOUNTED

FILTER ACCESSORY)

SIDE RETURN

DUCT OPENING

CORNER WEIGHTS %

OF TOTAL UNIT

WEIGHT

ELECTRICAL

POWER

ENTRANCE

THERMOSTAT

WIRE

ENTRANCE

TOP COVER

30% ± 2%

21% ± 2%

20% ± 2%

29% ± 2%

THREADED PVC CONDENSATE

DRAIN CONNECTION (3/4 N.P.T.)

IMPORTANT:

INSTALLATION MUST NOT INTERFERE WITH DRAINAGE OPENINGS

IN BOTTOM OF UNIT UNDER OUTDOOR COIL.

FIGURE 1

Model # Height “A”

B024, B025

⁄16"

41"

B030, B036

B042, B048

FRONT VIEW

REAR VIEW

SIDE VIEW

OUTDOOR

FAN GRILLE

AND

COMPRESSOR

ACCESS

BOTTOM

RETURN

DUCT

OPENING

BOTTOM

SUPPLY DUCT

OPENING

LIQUID

PRESSURE

SERVICE

PORT

CONTROL

ACCESS

PANEL

SUCTION

PRESSURE

SERVICE

PORT

SIDE SUPPLY

DUCT

OPENING

FILTER ACCESS

PANEL (FOR

UNIT MOUNTED

FILTER

ACCESSORY)

BLOWER/

EVAPORATOR

ACCESS

PANEL

THERMOSTAT

WIRE

ENTRANCE

ELECTRICAL POWER

ENTRANCE

THREADED PVC

CONDENSATED DRAIN

CONNECTION (3/4 N.P.T.)

SHOWN WITH DUCT COVERS REMOVED.

OUTDOOR

COIL

PROTECTIVE

GRILLE

SIDE RETURN

DUCT

OPENING

⁄32

ⴖ

⁄16

ⴖ

INSIDE

⁄16

ⴖ

⁄8

ⴖ

⁄16

ⴖ

⁄16

ⴖ

⁄16

ⴖ

⁄8

ⴖ

⁄16

ⴖ

⁄2

ⴖ

⁄16

ⴖ

⁄16

ⴖ

⁄8

ⴖ

⁄8

ⴖ

⁄16

ⴖ

⁄2

ⴖ

⁄16

ⴖ

⁄4

ⴖ

⁄16

ⴖ

INSIDE

⁄2

ⴖ

TYP.

⁄16

ⴖ

TYP.

⁄4

ⴖ

TYP.

⁄4

ⴖ

TYP.

⁄2

ⴖ

TYP.

⁄16

ⴖ

TYP.

⁄16

ⴖ

⁄16ⴖ

⁄16

ⴖ

⁄16ⴖ

III. CHECKING PRODUCT RECEIVED

Upon receiving the unit, inspect it for any damage from shipment. Claims for damage,

either shipping or concealed, should be filed immediately with the shipping company.

Check the unit model number, heating size, electrical characteristics, and accessories to

determine if they are correct.

IV. EQUIPMENT PROTECTION FROM THE

ENVIRONMENT

The metal parts of this unit may be subject to rust or deterioration in adverse environmen-

tal conditions. This oxidation could shorten the equipment’s useful life. Salt spray, fog or

mist in seacoast areas, sulphur or chlorine from lawn watering systems, and various chem-

ical contaminants from industries such as paper mills and petroleum refineries are espe-

cially corrosive.

If the unit is to be installed in an area where contaminants are likely to be a prob-

lem, special attention should be given to the equipment location and exposure.

1. Avoid having lawn sprinkler heads spray direction on the unit cabinet.

2. In coastal areas, locate the unit on the side of the building away from the waterfront.

3. Shielding provided by a fence or shrubs may give some protection.

4. Elevating the unit off its slab or base enough to allow air circulation will help avoid

holding water against the basepan.

Regular maintenance will reduce the buildup of contaminents and help to protect

the unit’s finish.

1. Frequent washing of the cabinet, fan blade and coil with fresh water will remove most

of the salt or other contaminants that build up on the unit.

2. Regular cleaning and waxing of the cabinet with an automobile polish will provide

some protection.

3. A liquid cleaner may be used several times a year to remove matter that will not wash

off with water.

Several different types of protective coatings are offered in some areas. These coatings

may provide some benefit, but the effectiveness of such coating materials cannot be veri-

fied by the equipment manufacturer.

The best protection is frequent cleaning, maintenance and minimal exposure to

contaminants.

V. INSTALLATION

A. GENERAL

1. PRE-INSTALLATION CHECK-POINTS

Before attempting any installation, the following points should be carefully consid-

ered:

a. Structural strength of supporting members.

(rooftop installation)

b. Clearances and provision for servicing.

c. Power supply and wiring.

d. Air duct connections.

e. Drain facilities and connections.

f. Location for minimum noise.

2. LOCATION

These units are designed for outdoor installations. They can be mounted on a

slab or rooftop. They are not to be installed within any part of a structure such as

an attic, crawl space, closet, or any other place where condenser air flow is

restricted or other than outdoor ambient conditions prevail. Since the application

WARNING

THE MANUFACTURER’S WARRAN-

TY DOES NOT COVER ANY DAM-

AGE OR DEFECT TO THE HEAT

PUMP CAUSED BY THE ATTACH-

MENT OR USE OF ANY COMPO-

NENTS, ACCESSORIES OR

DEVICES (OTHER THAN THOSE

AUTHORIZED BY THE MANUFAC-

TURER) INTO, ONTO OR IN CON-

JUNCTION WITH THE HEAT PUMP.

YOU SHOULD BE AWARE THAT

THE USE OF UNAUTHORIZED

COMPONENTS, ACCESSORIES OR

DEVICES MAY ADVERSELY

AFFECT THE OPERATION OF THE

HEAT PUMP AND MAY ALSO

ENDANGER LIFE AND PROPERTY.

THE MANUFACTURER DISCLAIMS

ANY RESPONSIBILITY FOR SUCH

LOSS OR INJURY RESULTING

FROM THE USE OF SUCH UNAU-

THORIZED COMPONENTS, ACCES-

SORIES OR DEVICES.

WARNING

DISCONNECT ALL POWER TO THE UNIT BEFORE STARTING MAINTENANCE.

FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK OR DEATH.

FIGURE 2

PACKAGE HEAT PUMP

OUTSIDE SLAB INSTALLATION, BASEMENT OR

CRAWL SPACE DISTRIBUTION SYSTEM

FIGURE 3

PACKAGE HEAT PUMP

OUTSIDE SLAB INSTALLATION, CLOSET DISTRIBUTION

60ⴖ OVERHEAD

CLEARANCE

0ⴖ MIN.

CLEARANCE

24ⴖ TO SERVICE

BLOWER & EVAPORATOR

0 ⴖ CLEARANCE AROUND

SUPPLY DUCT TO

COMBUSTIBLE STRUCTURE

12ⴖ CLEARANCE

WITHOUT

ECONOMIZER

24ⴖ CLEARANCE

WITH

ECONOMIZER

36ⴖ

I268

I267

SUPPLY DUCT AT

CLOSET CEILING

FILTER

GRILL

IMPORTANT: UNIT MUST BE LEVEL

TO PREVENT WATER MIGRATION

SLAB

FLOOR

THERMOSTAT

WIRE CONDUIT

POWER

SUPPLY

CONDUIT

SERVICE

ACCESS PANELS

DO NOT BLOCK

ACCESS

BRANCH

CIRCUIT

DISCONNECT

FIGURE 4

PACKAGE HEAT PUMP

RIGGING FOR LIFTING

ST-A1100-01

RIGGING

NOT

PROVIDED

SEE DETAIL A

DETAIL A

of the units is of the outdoor type, it is important to consult your local code authori-

ties at the time the first installation is made.

B. OUTSIDE SLAB INSTALLATION (Typical outdoor slab installations are shown

in Figures 2 and 3.)

1. Select a location where external water drainage cannot collect around the unit.

2. Provide a level concrete slab extending a minimum 3" beyond all four sides of the

unit. The slab should be sufficient above grade to prevent ground water from

entering the unit. IMPORTANT: To prevent transmission of noise or vibration,

slab should not be connected to building structure.

3. The location of the unit should be such as to provide proper access for inspection

and servicing.

4. Locate unit where operating sounds will not disturb owner or neighbors.

5. Locate unit so roof runoff water does not pour directly on the unit. Provide gutter

or other shielding at roof level. Do not locate unit in an area where excessive

snow drifting may occur or accumulate.

6. It is essential that the unit be elevated above the base pad to allow for conden-

sate drainage and possible refreezing of condensation. Provide a base pad which

is slightly pitched away from the structure. Route condensate off base pad to an

area which will not become slippery and result in personal injury. IMPORTANT:

Do not interfere with openings in bottom of unit.

7. Where snowfall is anticipated, the height of the unit above the ground level must

be considered. Mount unit high enough to be above average area snowfall and to

allow for proper condensate drainage. IMPORTANT: Do not interfere with open-

ings in bottom of unit.

C. CLEARANCES

The following minimum clearances must be observed for proper unit performance

and serviceability.

1. Provide 36" minimum clearance at the front and right side of the unit for service

access. Provide 12" minimum clearance on the left side of the unit for air inlet.

2. Provide 60" minimum clearance between top of unit and maximum 3 foot over-

hang.

3. Unit is design certified for application on combustible flooring with 0" minimum

clearance.

4. See Figure 2 for illustration of minimum installation-service clearances.

D. ROOFTOP INSTALLATION

1. Before locating the unit on the roof, make sure that the strength of the roof and

beams is adequate at that point to support the weight involved. (See specification

sheet for weight of unit.) This is very important and user’s responsibility.

2. For rigging and roofcurb details, see Figures 4 and 5. Use accessory lift brackets

and field-furnished spreaders.

3. For roofcurb assembly, see Roofcurb Installation Instructions.

4. If the roofcurb is not used, provisions for disposing of condensate water runoff

during defrosting must be provided.

5. The unit should be placed on a solid and level roofcurb or platform of adequate

strength. IMPORTANT: Do not interfere with opening in bottom of unit. (See

Figures 6 and 7.)

6. The location of the unit on the roof should be such as to provide proper access for

inspection and servicing.

IMPORTANT: If unit will not be put into service immediately, cover supply and return

openings to prevent excessive condensation.

VI. DUCTWORK

Ductwork should be fabricated by the installing contractor in accordance with local

codes, state codes and NFPA90A. Industry manuals may be used as a guide when siz-

ing and designing the duct system - contact Air Conditioning Contractors of America,

1513 16th St. N.W., Washington, D.C. 20036.

Place the unit as close to the space to be air conditioned as possible allowing clearance

dimensions as indicated. Run ducts as directly as possible to supply and return outlets.

Use of non-flammable waterproof flexible connectors on both supply and return connec-

tions at the unit to reduce noise transmission is recommended.

It is preferable to install the unit on the roof of the structure if the registers or diffusers

are located on the wall or in the ceiling. Consider a slab installation when the registers

are low on a wall or in the floor.

On ductwork exposed to outside air conditions of temperature and humidity, use a mini-

mum of 2" of insulation and a vapor barrier. Distribution system in attic, furred space or

crawl space should be insulated with at least 2" of insulation with vapor barrier. One-half

to 1" thickness of insulation is usually sufficient for ductwork inside the air conditioned

space.

Provide balancing dampers for each branch duct in the supply system. Properly support

the ductwork from the structure.

When installing ductwork use noncombustible flexible connectors between ductwork and

unit to reduce noise and vibration transmission into the ductwork.

WARNING

DO NOT, UNDER ANY CIRCUMSTANCES, CONNECT RETURN DUCTWORK

TO ANY OTHER HEAT PRODUCING DEVICE SUCH AS A FIREPLACE INSERT,

STOVE, ETC. UNAUTHORIZED USE OF SUCH DEVICES MAY RESULT IN FIRE,

CARBON MONOXIDE POISONING, EXPLOSION, PROPERTY DAMAGE,

FIGURE 5

PACKAGE HEAT PUMP

ROOFCURB INSTALLATION

I270 I271

VII. FILTERS

Filters are not provided with this unit. They may be supplied and installed in the return

air duct by the installer. A field installed filter grille is recommended for easy and conve-

nient access to the filters for periodic inspection and cleaning. Filters must have ade-

quate face area for the rated air quantity of the unit. See Airflow Performance Table - or

Electrical and Physical Data Table - for recommended filter size.

However, if an internal filter is required, an optional internal filter kit is available which

will work for downflow or horizontal applications. For installation, see Filter Kit

Installation Instruction.

NOTE: Do not operate the system without filters.

POWER

SUPPLY

CONDUIT

CONDENSATE INTO

ROOFDRAIN IF REQ’D

BY LOCAL CODES.

SERVICE ACCESS

PANELS. DO NOT

BLOCK ACCESS

I272

FIGURE 6

PACKAGE HEAT PUMP

FLAT ROOFTOP INSTALLATION, ATTIC OR DROP CEILING

DISTRIBUTION SYSTEM. MOUNTED ON

ROOFCURB. CURB MUST BE LEVEL

THERMO-

STAT WIRE

CONDUIT

BRANCH CIRCUIT

DISCONNECT

FIGURE 7

PACKAGE HEAT PUMP

PITCHED ROOFTOP INSTALLATION, ATTIC

OR DROP CEILING DISTRIBUTING SYSTEM.

MUST BE MOUNTED LEVEL.

SERVICE ACCESS

PANELS. DO NOT

BLOCK ACCESS

SUPPLY PLENUM

THER-

MOSTAT

WIRE

CONDUIT

BRANCH

CIRCUIT

DISCONNECT

POWER SUPPLY

CONDUIT

CONDENSATE

DRAIN INTO

ROOFDRAIN IF

REQ’D BY LOCAL

CODES.

I273

VIII.CONVERSION PROCEDURE

1. DOWNFLOW TO HORIZONTAL

a. Remove screws and covers from outside of supply and return sections.

b. Install gasket (supplied with parts bag) around perimeter of covers as illustrated in

“Cover Gasket Detail,” Figure 8.

c. Install covers in bottom of unit with insulated side up.

NOTE: Slip back flange of cover under tab on bottom supply duct opening.

d. Secure covers to base of unit with screw engaging prepunched holes in unit base.

2. HORIZONTAL TO DOWNFLOW

a. Remove screws and covers from the downflow supply and return sections. Both

covers are accessible from the inside of the unit.

NOTE: Supply cover must be rotated 90º before it can be removed.

b. Install gasket (supplied with parts bag) around perimeter of cover on the insulated

side. See Figure 9.

c. Install covers on the outside of the unit over the horizontal supply and return

opening using existing screws.

IX. CONDENSATE DRAIN

The indoor coil condensate drain ends with a threaded (3/4" NPT) PVC stub. A trap is

built in for proper condensate drainage and to prevent debris from being drawn into the

unit. Do not connect drain to closed sewer line. It is recommended that a PVC cement not

be used so that the drain line can be easily cleaned in the future.

NOTE: Do not install an external trap.

FIGURE 9

COVER GASKET DETAIL

FOR UNITS SHIPPED FOR DOWNFLOW APPLICATION

BEING CONVERTED TO SIDE DISCHARGE

TAPE

AROUND FLANGE

SUPPLY/RETURN

AIR COVER

FIGURE 8

COVER GASKET DETAIL

FOR UNITS SHIPPED FOR SIDE DISCHARGE

APPLICATION BEING CONVERTED TO DOWNFLOW

TAPE

AROUND FLANGE

SUPPLY/RETURN

AIR COVER

I654

X. CONDENSATE DRAIN, OUTDOOR COIL

The outdoor coil during heating operation will sweat or run water off. The outdoor coil will

also run water off during the defrost cycle. See Section V, Installation, for mounting pre-

cautions.

XI. ELECTRICAL WIRING

Field wiring must comply with the National Electrical Code* state and local ordinances

that may apply.

*C.E.C. in Canada

A. POWER WIRING

1. It is important that proper electrical power is available at the unit. Voltage should

not vary more than 10% from that stamped on the unit rating plate. On three

phase units, phases must be balanced within 3%.

2. Install a branch circuit disconnect within sight of the unit and of adequate size to

handle the starting current.

3. For branch circuit wiring (main power supply to unit disconnect), the minimum

wire size can be determined from the circuit ampacity found on the unit nameplate

or from Table F and the National Electrical Code or Canadian Electrical Code.

4. This unit incorporates single point electrical connection for unit and electric heat

accessory.

5. Power wiring must be run in grounded rain-tight conduit. Connect the power field

wiring as follows:

a. NO ELECTRIC HEAT - Connect the field wires directly to the contactor in the

unit control box. Connect ground wire to ground lug.

b. WITH ELECTRIC HEAT - Connect the field wires to the terminal block on the

electric heater kit. Connect the ground wire to the ground lug on the heater kit.

NOTE: For installation of the heater kit, follow the instructions provided with the

heater kit.

6. The pigtail wires in the electric heat box are factory wired to the contactor in the

control box and are protected by internal fuses in the hinged fuse box mounted

under the control box. See label on fuse box cover for fuse sizing.

7. DO NOT connect aluminum field wires to electric heat kit power input terminals.

B. CONTROL WIRING (Class II)

1. Do not run low voltage wiring in conduit with power wiring.

2. Control wiring is routed through the 7/8" hole approximately 11" from the unit top

in the corner post adjacent to the control box. Use a minimum #18 AWG thermo-

stat wire. For wire lengths exceeding 50', use #16 AWG thermostat wire. The low

voltage wires are connected to the unit pigtails which are supplied with the unit in

the low voltage connection box located below the unit control box. See Figure 10.

3. It is necessary that only heat pump thermostats be used. Please contact your dis-

tributor for part number information.

4. Figure 11 shows representative low voltage connection diagrams. Read your ther-

mostat installation instructions for any special requirements for your specific ther-

mostat. These connection diagrams are wired to minimize the amount of auxiliary

electric heaters to be energized during defrost.

NOTE: Units installed in Canada require that an outdoor thermostat (30,000 min.

cycles of endurance) be installed and be wired with C.E.C. Class I wiring.

C. INTERNAL WIRING

1. A diagram of the internal wiring of this unit is located on the electrical control box

cover. If any of the original wire as supplied with the appliance must be replaced,

the wire gauge and insulation must be the same as original wiring.

D. GROUNDING

WARNING

THE UNIT MUST BE PERMANENTLY GROUNDED. A GROUNDING LUG IS

PROVIDED IN THE ELECTRIC HEAT KIT FOR A GROUND WIRE. (SEE FIGURE

10.) FAILURE TO GROUND THIS UNIT CAN RESULT IN FIRE OR ELECTRICAL

SHOCK CAUSING PROPERTY DAMAGE, SEVERE PERSONAL INJURY OR

DEATH.

GROUNDING MAY ALSO BE ACCOMPLISHED BY GROUNDING THE POWER

LINE CONDUIT TO THE UNIT. MAKE SURE THE CONDUIT NUT LOCKING

TEETH HAVE PIERCED THE INSULATING PAINT FILM OF THE SIDE PANEL.

E. THERMOSTAT

Mount the thermostat on an inside wall about five feet above the floor in a location

where it will not be affected by unconditioned air, sun, or drafts from open doors or

other sources. READ installation instructions in heat pump thermostat package

CAREFULLY because each has some different wiring requirements.

FIGURE 10

FIGURE 11

VOLTAGE CONNECTIONS DIAGRAMS

CONTROL BOX

CONTROL BOX COVER

CENTER POST

ELECTRIC HEATER KIT

LOW VOLTAGE BOX

CORNER POST

XII. INDOOR AIR FLOW DATA

All 208/230 volt units are equipped with multi-speed indoor blower motors. Each unit is

shipped factory wired for the proper speed at a normal external static. See the blower

performance data in this manual.

XIII. CRANKCASE HEAT (OPTIONAL)

At initial startup or after extended shutdown periods, make sure crankcase heat is ener-

gized for at least 12 hours before compressor is started (disconnect switch closed and

wall thermostat “OFF” position).

Crankcase heat is not required on scroll type compressors, but may be necessary for

difficult starting situations.

XIV.PRE-START CHECK

1. Is unit properly located and slightly slanted toward indoor condensate drain?

2. Is ductwork insulated, weatherproofed, with proper spacing to combustible materi-

als?

3. Is air free to travel to and from outdoor coil? (See Figure 2.)

4. Is the wiring correct, tight, and according to unit wiring diagram?

5. Is unit grounded?

6. Are field supplied air filters in place and clean?

7. Do the outdoor fan and indoor blower turn freely without rubbing, and are they tight

on the motor shafts?

8. Has crankcase heat (if required) been on for at least 12 hours?

9. Is unit elevated to allow for outdoor coil condensate drainage during heating opera-

tion and defrost?

XV. STARTUP

1. Turn thermostat to “OFF,” turn “on” power supply at disconnect switch.

2. Turn temperature setting as high as it will go.

3. Turn fan switch to “ON.”

4. Indoor blower should run. Be sure it is running in the right direction.

5. Adjust discharge air grilles and balance system.

6. Turn fan switch to “AUTO.” Turn system switch to “COOL” and turn temperature set-

ting below room temperature. Unit should run in cooling mode.

7. Is outdoor fan operating correctly in the right direction?

8. Is compressor running correctly.

9. Turn thermostat system switch to “HEAT.” Unit should stop. Wait 5 minutes, then

raise temperature setting to above room temperature. Unit should run in heating

mode and after about 30 to 50 seconds auxiliary heaters, if installed, should come

on.

10. Check the refrigerant charge using the instructions located on control box cover.

Replace service port caps. Service port cores are for system access only and will

leak if not tightly capped.

11. Turn thermostat system switch to proper mode “HEAT” or “COOl” and set thermostat

to proper temperature setting. Record the following after the unit has run some time.

A. Operating Mode _______________________________

B. Discharge Pressure (High)___________________PSIG

C.Vapor Pressure at Compressor (Low) __________PSIG

D.Vapor Line Temperature at Compressor __________°F.

E. Indoor Dry Bulb______________________________°F.

F. Indoor Wet Bulb _____________________________°F.

G.Outdoor Dry Bulb ____________________________°F.

H.Outdoor Wet Bulb____________________________°F.

I. Voltage at Contactor ________________________Volts

J. Current at Contactor _______________________Amps

K. Model Number_________________________________

L. Serial Number _________________________________

M.Location______________________________________

N.Owner _______________________________________

O.Date_________________________________________

12. Check ducts for condensation and air leaks.

13. Check unit for tubing and sheet metal rattles.

14. Instruct the owner on operation and maintenance.

15. Leave “INSTALLATION” and ”USE AND CARE“ instructions with owner

XVI. OPERATION

Most single phase units are operated PSC (no start relay or start capacitor). It is impor-

tant that such systems be off for a minimum of 5 minutes before restarting to allow

equalization of pressures. Do not move the thermostat to cycle unit without waiting five

minutes. To do so may cause the compressor to stop on an automatic open overload

device or blow a fuse. Poor electrical service can cause nuisance tripping in overloads

or blow fuses.

IMPORTANT: The compressor has an internal overload protector. Under some condi-

tions, it can take up to 2 hours for this overload to reset. Make sure overload has had

time to reset before condemning the compressor.

Some models may be factory equipped with a start relay and start capacitor.

Most single phase 208/240 volt units are equipped with a time delay control (TDC1). The

control allows the blower to operate for up to 90 seconds after the thermostat is satis-

fied.

XVII. AUXILIARY HEAT

The amount of auxiliary heat required depends on the heat loss of the structure to be

heated and the capacity of the heat pump. It is good practice to install strip heat to main-

tain at least 60ºF indoor temperatures in case of compressor failure. The auxiliary heat

is energized by the second stage of the thermostat. The amount of electric heat that is

allowed to come on, as determined by the output of the heat pump, may be controlled by

an outdoor thermostat.

A. CONTROL SYSTEM OPERATION

1. In the cooling mode, the thermostat will, on a call for cooling, energize the com-

pressor contactor and the indoor blower relay. The indoor blower can be operated

continuously by setting the thermostat fan switch at the “ON” position. The revers-

ing valve coil is de-energized when the changeover relay is energized.

2. In the heating mode, the first heat stage of the thermostat will energize the com-

pressor contactor and the indoor blower relay. The second heat stage will turn on

one or more supplementary resistance heaters. The reversing valve is energized

except in defrost. If required or considered desirable, the resistance heat may

also be controlled by outdoor thermostats.

WARNING

ONLY ELECTRIC HEATER KITS SUPPLIED BY THIS MANUFACTURER AS

DESCRIBED IN THIS PUBLICATION HAVE BEEN DESIGNED, TESTED, AND

EVALUATED BY A NATIONALLY RECOGNIZED SAFETY TESTING AGENCY

FOR USE WITH THIS UNIT. USE OF ANY OTHER MANUFACTURED ELECTRIC

HEATERS INSTALLED WITHIN THIS UNIT MAY CAUSE HAZARDOUS CONDI-

TIONS RESULTING IN PROPERTY DAMAGE, FIRE, BODILY INJURY OR

DEATH.

XVIII. DEMAND DEFROST CONTROL AND

HIGH/LOW PRESSURE CONTROLS

The demand defrost control monitors the outdoor ambient temperature, outdoor coil

temperature and the compressor run time to determine when a defrost cycle is

required.

Enhanced Feature Demand Defrost Control: This defrost control has high and

low pressure control inputs with unique pressure switch logic built into the micro-

processor to provide compressor and system protection without nuisance lockouts.

The control cycles the compressor off for 30 seconds at the beginning and the end

of the defrost cycle to eliminate the increased compressor noise caused by rapidly

changing system pressures when the reversing valve switches. See next page for

diagnostic flash codes and sensor resistance values at various temperatures.

DEFROST INITIATION

A defrost will be initiated when the three conditions below are satisfied:

1. The outdoor coil temperature is below 35°F as measured by a good coil sensor,

2. The compressor has operated for at least 34 minutes with the outdoor coil tem-

perature below 35°F and

3. The measured difference between the ambient temperature and the outdoor

coil temperature is greater than the calculated difference determined by the

defrost control microprocessor.

DEFROST TERMINATION

Once a defrost is initiated, the defrost will continue until fourteen minutes has

elapsed or the coil temperature has reached the selected termination temperature.

The factory setting is 70°F but can be changed to 50°F, 60°F, or 80°F by relocating

the jumper on the control board.

TEMPERATURE SENSORS

The coil sensor is located on the outdoor coil near the point fed by the distribution

tubes from the expansion device, on the top most cross-over tube. The ambient air

sensor is located outside the control box so it can sense outdoor temperatures.

If the ambient sensor fails, the defrost control will initiate a defrost every 34 minutes

of compressor run time with the coil temperature below 35°F.

If the coil sensor fails, the defrost control will not initiate a defrost.

TEST MODE

The test mode is initiated by shorting the TEST pins. The unit must have an active

heat pump heating call to enter the test mode. In this mode of operation, the enable

temperature is ignored and all timers are sped up. To initiate a manual defrost,

short and hold the TEST pins. Remove the short when the system switches to

defrost mode after the compressor noise abatement delay. The defrost will termi-

nate on time (14 minutes) or when the termination temperature has been reached.

Test Sequence of Operation:

1) Provide a heating call to the heat pump.

2) Short test pins to bypass anti-short cycle timer. (If unit is running, this step is not

necessary.)

3) Short test pins and hold them shorted to enter defrost mode.

4) Release test pins once control exits noise abatement delay.

5) Monitor coil temperature when control exits defrost.

6) Unit should return to heating mode.

TROUBLE SHOOTING DEMAND DEFROST

During the test mode the coil temperature should be monitored. If the system exits

defrost at approximately the termination temperature, the control is operating norml-

ly. If not, check the coil and ambient temperature sensor resistances, using the sen-

sor temperature vs. resistance table at the end of this section.

Immerse the sensor in water and measure the resistance of the sensor. At 35°F the

resistance of the sensor should be approximately 30,000 ohms.

Ensure that the coil sensor is properly installed that is not loose or touching the cab-

inet.

HIGH/LOW PRESSURE CONTROL MONITORING - ENHANCED

DEFROST CONTROL

Status of high and low pressure controls is monitored by the enhanced feature

demand defrost control and the following actions are taken.

High Pressure Control – Provides active protection in both cooling and heating

modes at all outdoor ambient temperatures. The high pressure control is an auto-

matic reset type and opens at approximately 610 psig and closes at approximately

420 psig. The compressor and fan motor will stop when the high pressure control

opens and will start again if the high side pressure drops to approximately 420 psig

where the automatic reset high pressure control resets. If the high pressure control

opens 3 times within a particular call for heating or cooling operation, the defrost

control will lock out compressor and outdoor fan operation.

Low Pressure Control – Provides active protection in both heating and cooling

modes at all outdoor ambient temperatures. The low pressure control is an auto-

matic reset type and opens at approximately 15 psig and closes at approximately

40 psig. Operation is slightly different between cooling and heating modes.

Cooling Mode: The compressor and fan motor will stop when the low pressure

control opens and will start again when the low side pressure rises to approxi-

mately 40 psig after the low pressure control automatically resets. If the low

pressure switch opens 3 times within a particular call for cooling operation, the

defrost control will lock out compressor and outdoor fan operation.

Heating Mode: The compressor and outdoor fan motor will stop when the low

pressure control opens and will start again when the low side pressure rises to

approximately 40 psig when the low pressure control automatically resets. If the

low pressure switch trips 3 times within 120 minutes of operation during a par-

ticular call for heating operation, the defrost control will lock out compressor

and outdoor fan operation. If the lock-out due to low pressure occurs at an out-

door ambient temperature below 5°F, the defrost control will automatically exit

the lock-out mode when the outdoor ambient temperature rises to 5°F. This fea-

ture is necessary since the low pressure control could possibly have opened

due to the outdoor ambient being very low rather than an actual system fault.

Exiting Lock-Out Mode: To exit the lock-out mode, remove 24 volts to the defrost

control by removing power to the unit or by shorting the two defrost control pins

together.

ENHANCED FEATURE DEFROST CONTROL DIAGNOSTIC CODES

SENSOR TEMPERATURE VS. RESISTANCE TABLE

LED 1 LED 2 Control Board Status

OFF OFF No Power

ON ON Coil Sensor Failure

OFF ON Ambient Sensor Failure

FLASH FLASH Normal

OFF FLASH Low Pressure Lockout (short test pins to reset)

FLASH OFF High Pressure Lockout (short test pins to reset)

ON FLASH Low Pressure Control Open

FLASH ON High Pressure Control Open

Alternate Flashing 5 Minute Time Delay

Degrees C Degrees F Ohms

-20 -4 96,974

-10 14 55,298

0 32 32,650

10 50 19,903

20 68 12,493

25 77 10,000

30 86 8,056

40 104 5,324

XIX. GENERAL DATA - RQNL- MODELS

NOMINAL SIZES 2-4 TONS [7.1-14.6 kW]

Model RQNL - Series B024JK B030JK B036CK B036JK

Cooling performance

Gross Cooling Capacity Btu [kW] 24,400 [7.15] 29,000 [8.5] 36,200 [10.61] 36,200 [10.61]

EER, SEER

11/13 11/13 11/13 11/13

Nominal CFM/ARI Rated CFM [L/s] 800/800 [378/378] 1000/1000 [472/472] 1200/1250 [566/590] 1200/1250 [566/590]

ARI Net Cooling Capacity Btu [kW] 23,600 [6.91] 27,800 [8.15] 35,000 [10.26] 35,000 [10.26]

Net Sensible Capacity Btu [kW] 17,600 [5.16] 20,800 [6.09] 26,000 [7.62] 26,000 [7.62]

Net Latent Capacity Btu [kW] 6,000 [1.76] 7,000 [2.05] 9,000 [2.64] 9,000 [2.64]

Net System Power kW 2.15 2.53 3.18 3.18

Heating Performance (Heat Pumps)

High Temp. Btuh [kW] Ratiing 23,600 [6.91] 28,200 [8.26] 34,000 [9.96] 34,000 [9.96]

System Power KW / COP 2.02/3.4 2.45/3.4 2.86/3.5 2.86/3.5

Low Temp. Btuh [kW] Rating 13,000 [3.81] 16,000 [4.69] 19,500 [5.71] 19,500 [5.71]

System Power KW / COP 1.9/2 2.26/2.1 2.61/2.2 2.61/2.2

HSPF (Btu/Watts-hr) 7.7 7.7 7.7 7.7

Compressor

No/Type 1/Copeland Scroll 1/Copeland Scroll 1/Copeland Scroll 1/Copeland Scroll

Outdoor Sound Rating (dB)

76 76 76 76

Outdoor Coil - Fin Type Louvered Louvered Louvered Louvered

Tube Type Rifled Rifled Rifled Rifled

Tube Size in. [mm] OD 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]

Face Area sq. ft. [sq. m] 14.51 [1.35] 16.32 [1.52] 11.2 [1.04] 11.2 [1.04]

Rows / FPI [FPcm] 1 / 22 [9] 1 / 22 [9] 2 / 22 [9] 2 / 22 [9]

Refrigerant Control TX Valves TX Valves TX Valves TX Valves

Indoor Coil - Fin Type Louvered Louvered Louvered Louvered

Tube Type Rifled Rifled Rifled Rifled

Tube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]

Face Area sq. ft. [sq. m] 5.54 [0.51] 7.39 [0.69] 7.39 [0.69] 7.39 [0.69]

Rows / FPI [FPcm] 2 / 15 [6] 2 / 15 [6] 2 / 15 [6] 2 / 15 [6]

Refrigerant Control TX Valves TX Valves TX Valves TX Valves

Drain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]

Outdoor Fan - Type Propeller Propeller Propeller Propeller

No. Used/Diameter in. [mm] 1/22 [558.8] 1/22 [558.8] 1/22 [558.8] 1/22 [558.8]

Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1

CFM [L/s] 2700 [1274] 2700 [1274] 2700 [1274] 2700 [1274]

No. Motors/HP 1 at 1/5 HP 1 at 1/5 HP 1 at 1/5 HP 1 at 1/5 HP

Motor RPM 1075 1075 1075 1075

Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC Centrifugal

No. Used/Diameter in. [mm] 1/9x7 [228.6x177.8] 1/10x9 [254x228.6] 1/10x9 [254x228.6] 1/10x9 [254x228.6]

Drive Type/No. Speeds Direct/2 Direct/3 Direct/1 Direct/1

No. Motors 1111

Motor HP 1/4 1/2 1/3 1/3

Motor RPM 1075 1075 1075 1075

Motor Frame Size 48 48 48 48

Filter - Type Field Supplied Field Supplied Field Supplied Field Supplied

Furnished No No No No

(NO.) Size Recommended in. [mm x mm x mm] (1)1x20x20 [25x508x508] (1)1x24x24 [25x610x610] (1)1x24x24 [25x610x610] (1)1x24x24 [25x610x610]

Refrigerant Charge Oz. [g] 98 [2778] 108 [3062] 146 [4139] 146 [4139]

Weights

Net Weight lbs. [kg] 391 [177] 444 [201] 471 [214] 468 [212]

Ship Weight lbs. [kg] 401 [182] 455 [206] 482 [219] 479 [217]

Continued ->

Page is loading ...

Rheem RQPL-B049JK000 Installation guide

Brand: Rheem

Model: RQPL-B049JK000

Type: Installation guide

This manual is also suitable for

Download PDF

report

Rheem RQPL-B049JK000 Installation guide

This manual is also suitable for

Rheem RQPL-B049JK000 Installation guide

Related papers

Other documents