Star Trac E Series Treadmill E-TRxe Owner's manual
- Type
- Owner's manual
Assembly & Setup
STAR TRAC FITNESS
0 of 1
637-1617 Rev: A
Star Trac Treadmill Installation Checklist
Use the checklist below to ensure proper installation of Star Trac Treadmills:
All parts and hardware from packaging are accounted for.
Check all screws and bolts to ensure they are all tightened to the proper torque specifications.
Neck is properly mounted and secured to the base frame.
Left and right handrails are properly mounted and secured to the base frame.
Display frame is properly mounted and secured to the neck and handrails.
Electronic display console is properly mounted and secured to the display frame.
All cables and harnesses are properly plugged to their respective connectors.
All cables inside the motor compartment are routed away from all moving parts.
Motor shroud and side bed covers are properly installed and secured.
Unit is levelled to the floor.
Ensure the power cable is zip tied to the undercarriage of the unit securely.
Verify the running belt is properly aligned on the rollers.
Using a chest strap or wireless heart rate simulator, verify heart rate is recording properly.
Verify machine software versions and update to most recent if necessary.
Access maintenance mode and process a motor calibration.
Access maintenance mode and set elevation values.*
*Last change was done in Dec. 2016. This change introduced 1.05 Display software, for 8-Series LCD
displays, and 1.6 Translator Board software, for E and 8-Series 15”
Please note that this new version changed the elevation parameters as outlined below:
OLD (pre-V1.05) Calibration Values:
Model
Incline Range
Min (zero elevation)
Max (full elevation)
E-TRx
0% - 20%
230
38
E-TR
0% - 15%
230
70
S-TRc
0% - 15%
235 - 230
67 – 75
S-TRx
0% - 15%
235 - 230
67 – 75
NEW (post-V1.05) Calibration Values:
Model
Incline Range
Min (zero elevation)
Max (full elevation)
E-TRx / 8-TRx
0% - 20%
228
11
E-TR / 8-TR
0% - 15%
228
55
The elevation values above are set by accessing the MTT mode within the maintenance mode and
manually adjusting the values.
Assembly & Setup
STAR TRAC FITNESS
1 of 1
637-1617 Rev: A
Verify all user functions of the unit are in good working order – hot bar including the emergency pull stop,
pause/stop button, speed/incline keys, heart rate, fan keypad, quick start/ stop, and general keypad overlay.
Run the “Alpine Pass” program for 2-3 minutes on max elevation and max speed to ensure proper
function of the each newly installed unit.
Overall visual & cosmetic inspection: All equipment is to be wiped down and checked for defects prior to
leaving the facility. Installer is to contact an authorized Core Health & Fitness representative while on site, if
there are any issues that have not been resolved.
ATTENTION
Star Trac requires a dedicated, isolated 20Amp circuit (no shared grounds, positives, or neutrals) for each
treadmill. Please ensure power requirements are met before install. Star Trac also recommends that the
treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe/easy ingress and egress. Even more
importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill.
As with any motorized equipment, the area where treadmills are located must be free of obstructions and
fixtures with sharp edges to prevent injury.
-
1
-
2
Star Trac E Series Treadmill E-TRxe Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Star Trac E Series Treadmill E-TRe User manual
-
Star Trac E Series Treadmill E-TRx User manual
-
-
-
-
-
Stairmaster 8UB-LCD User manual
-
-
-