Blaze King Clarity 2118 SP Owner's manual

Brand: Blaze King

Model: Clarity 2118 SP

Category: Stoves

Type: Owner's manual

180-CL2118.SP.1 v1.00 June 30, 2020

CLARITY CL2118.SP.1

DIRECT VENT GAS ROOM HEATER

with 7 Day Shuto Standing Pilot (SP)

For use with natural gas (NG) or propane (LPG)

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com

Date Installed: ____________

Serial No.: _____________

OPERATION &

INSTALLATION

MANUAL

WARNING: If the information in these

instructions are not followed exactly, a re

or explosion may result causing property

damage, personal injury or loss of life.

PFS Report #

F19-559

180-CL2118.SP.1 v1.00 June 30, 2020

Page 2

CL2118.SP.1

SAFETY PRECAUTIONS _________________________________________________________________ 4

GENERAL .................................................................................................................................................................... 4

YOUR SAFETY .......................................................................................................................................................... 5

INSTALLATION ..........................................................................................................................................................5

GENERAL INFORMATION ________________________________________________________________ 6

APPLIANCE CERTIFICATION ..............................................................................................................................6

INSTALLATION CODES .........................................................................................................................................6

SPECIFICATIONS.....................................................................................................................................................6

HIGH ALTITUDE INSTALLATION .....................................................................................................................6

CERTIFICATION LABEL __________________________________________________________________ 7

DIMENSIONS _____________________________________________________________________________ 8

CLEARANCE TO COMBUSTIBLES ...................................................................................................................8

LIGHTING INSTRUCTIONS _______________________________________________________________ 9

820 NOVA VALVE_________________________________________________________________________ 10

OPERATING INSTRUCTIONS ____________________________________________________________ 11

PILOT LIGHT ..............................................................................................................................................................11

LIGHTING THE BURNER ......................................................................................................................................11

OPTIONAL BLOWER...............................................................................................................................................11

MAINTENANCE and SERVICE____________________________________________________________ 12

ROUTINE MAINTENANCE .................................................................................................................................... 12

CLEANING SURFACES .........................................................................................................................................12

CLEANING THE GLASS .........................................................................................................................................12

GLASS DOOR REMOVAL .....................................................................................................................................13

GLASS DOOR REPLACEMENT ..........................................................................................................................14

BURNER REMOVAL ................................................................................................................................................ 14

SAFETY SCREEN REPLACEMENT ..................................................................................................................15

FUEL CONVERSION ...............................................................................................................................................16

INSTALLATION PLANNING _______________________________________________________________ 18

PRECAUTIONS .........................................................................................................................................................18

FRAMING - ROUGH OPENING ........................................................................................................................... 18

FRAMING - CORNER INSTALLTION .................................................................................................................19

WALL FINISH..............................................................................................................................................................20

CRACKING WALL FINISHES ...............................................................................................................................21

INSTALLATION ___________________________________________________________________________ 22

HARDWIRING FOR OPTIONAL BLOWER ......................................................................................................22

OPTIONAL BLOWER INSTALLATION FOR EXISTING CL2118 INSTALLATION ...............................23

INITIAL SETUP ..........................................................................................................................................................24

VENT TERMINATION LOCATION .......................................................................................................................25

REAR VENT INSTALLATION ................................................................................................................................ 26

CONVERSION TO REAR VENT .......................................................................................................................... 26

GAS CONNECTIONS .............................................................................................................................................. 29

VENTING .....................................................................................................................................................................31

TYPICAL VENTING EXAMPLES .........................................................................................................................32

VERTICAL VENT INSTALLATION ....................................................................................................................... 33

TABLE OF CONTENTS

180-CL2118.SP.1 v1.00 June 30, 2020

Page 3

CL2118.SP.1

Manufactured By

Valley Comfort Systems Inc.

1290 Commercial Way

Penticton, BC V2A 3H5

CANADA

Phone: 250-493-7444

Fax: 250-493-5833

Blaze King Industries

146 A Street

Walla Walla, WA 99362

U.S.A.

Phone: (509) 522-2730

Fax: (509) 522-9803

SAFETY PRECAUTIONS

VENT TERMINATION RESTRICTIONS ............................................................................................................35

VENT RESTRICTOR ...............................................................................................................................................37

AIR SHUTTER ADJUSTMENT ............................................................................................................................. 38

BURNER FLAME APPEARANCE .......................................................................................................................38

MOBILE HOME INSTALLATION .......................................................................................................................... 39

ELECTRICAL REQUIREMENTS: ........................................................................................................................39

RIGID VENTING PARTS LIST _____________________________________________________________ 42

VALVE REMOVAL & INSTALLATION _____________________________________________________ 49

PARTS LIST ______________________________________________________________________________ 50

TROUBLESHOOTING ____________________________________________________________________ 51

WARRANTY ______________________________________________________________________________ 52

NOTES ___________________________________________________________________________________ 56

180-CL2118.SP.1 v1.00 June 30, 2020

Page 4

CL2118.SP.1

SAFETY PRECAUTIONS

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings

exactly could result in serious injury,

death, or property damage.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the premises.

• Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the re department.

— Installation and service must be

performed by a qualied installer, service

agency or the gas supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certied

kit is used.

A safety screen designed to reduce the risk of burns

from the hot viewing glass is provided with this

appliance and shall be installed for the protection of

children and other at-risk individuals. If the safety

screen becomes damaged, the safety screen shall be

replaced with the manufacturer’s safety screen for this

appliance.

NOTE: Failure to follow these instructions could cause a malfunction of the replace, which could result in death, serious bodily injury, and/or

property damage.

GENERAL

• Installation and repair should be done by a qualied service person. The appliance should be inspected before the rst use and, at least,

annually by a qualied service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

It is imperative the control compartments, burners and circulating air passageways of the appliance be kept clean.

• If the CLARITY CL2118 is pulled out of its installation, and the vent-air intake pipes is disconnected for any reason, ensure that the vent-air

intake pipes are reconnected and re-sealed in accordance to the instructions noted in INSTALLATION - VERTICAL VENT INSTALLATION

or REAR VENT INSTALLATION.

• Due to high temperatures, the appliance should be located out of high trac areas and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface

temperatures and should stay away to avoid burn or clothing ignition.

• Young children should be carefully supervised when in the same room as the appliance. Toddlers, young children and others may be

susceptible to accidental contact burns. A physical barrier (safety screen) is required if there are at risk individuals in the house. To restrict

access to a replace or stove install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room

and away from hot surfaces. Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to operating

the appliance.

• Clothing or other ammable materials should not be placed on or near the appliance.

CALIFORNIA PROPOSITION 65

WARNING: This product can expose you to chemicals including

benzene, which is known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information:

www.P65Warnings.ca.gov

180-CL2118.SP.1 v1.00 June 30, 2020

Page 5

CL2118.SP.1

SAFETY PRECAUTIONS

YOUR SAFETY

• Have the venting system inspected annually by a qualied installer for blockage and signs of deterioration.

• To prevent injury, do not allow anyone who is unfamiliar with the stove to operate it.

• To prevent injury, if the pilot or pilot and burners have gone out on their own, open the glass door and wait 5

minutes to air out before attempting to relight the stove.

• Always keep the area around these appliances clear of combustible material, gasoline and other ammable

liquids and vapors.

• These appliances should not be used as a drying rack for clothing or for hanging Christmas stockings/

decorations.

• Due to the paint curing on the stove, a faint odor and slight smoking will likely be noticed when the stove is

rst used. Open a window until the smoking stops.

• Do not use this appliance if any part has been under water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

under water.

• Do not abuse the glass by striking it or slamming the door shut.

INSTALLATION

• Installation and service must be performed by a qualied installer, service agency or gas supplier

• Only doors certied with the appliance shall be used. (see door part numbers in “PARTS LIST”)

• This installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1 / NFPA 54 in the US, or the Natural Gas and Propane Installation Code, CSA B149.1 in

Canada.

• A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not

applicable, the Standard for Manufactured Home Installations, ANSI / NCSBCS A225.1, or Standard for Gas

Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

• Always connect this gas appliance to a vent system and vent to the outside of the building envelope. Never

vent to another room or inside the building. Make sure the specied vent pipe is used, properly sized and of

adequate height to provide sucient draft.

• The ow of combustion and ventilation air must not be obstructed .

• The appliance and its appliance main gas valve must be disconnected from the gas supply piping system

during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

• This gas appliance must not be connected to a chimney ue serving a separate solid-fuel burning appliance.

• The appliance, when installed, must be electrically grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code, ANSI / NFPA 70, in the US, or the Canadian

Electrical Code, CSA C22.1, in Canada.

• Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper

and dangerous operation. Verify proper operation after servicing.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THE DIAGRAMS IN THIS BOOKLET,

OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE, MAY

RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

DO NOT OPERATE WITH THE GLASS FRONT REMOVED, CRACKED OR BROKEN. REPLACEMENT

OF THE GLASS SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.

180-CL2118.SP.1 v1.00 June 30, 2020

Page 6

CL2118.SP.1

SPECIFICATIONS

MODEL

CL2118.SP

Natural Gas (NG) Propane (LPG)

Manifold Pressure 3.8” w.c. (0.95kPa) 10.6” w.c. (2.64 kPa)

Min. Supply Pressure for

Purpose of Input Adjustment

7” w.c. (1.74 kPa) 11.0” w.c. (2.74 kPa)

Orice Size DMS #39 DMS #1.5 mm

Nominal Input Rating 27,300 BTU/hr 26,200 BTU/hr

Minimum Input Rating 14,838 BTU/hr 14,120 BTU/hr

Altitude 0 - 4,500 ft. (0 - 1372 m) 0 - 4,500 ft. (0 - 1372 m)

Primary Air Opening 50% (Minimum) open

Electrical Rating 120 V.A.C. System 120 V.A.C. System

HIGH ALTITUDE INSTALLATION

When installing this appliance beyond 4500 ft. (1372 m) above sea level, the appliance must be properly de-

rated and installed according to local codes, in the absence of local codes, with the current National Fuel Gas

Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code, CSA-B149.1, in Canada.

GENERAL INFORMATION

INSTALLATION CODES

This appliance must be installed by a qualied gas

appliance installer. This appliance is certied for installation

in a bedroom or a bedsitting room. This appliance is only

for use with the type of gas indicated on the rating plate and

may be installed in an aftermarket, permanently located,

manufactured (mobile) home where not prohibited by

local codes. This appliance is not convertible for use with

other gases, unless a certied kit is used. Only for direct

discharge without duct connection. This appliance must

be direct vented using listed and approved Simpson Dura-

Vent, Selkirk, Security or American Metal Products vent

components.

We recommend

that our gas hearth

products be installed

and serviced by

professionals who are

certied in the U.S. by

the National Fireplace

Institute (NFI) as NFI

Gas Specialists.

APPLIANCE CERTIFICATION

This appliance is tested and certied to the following US and Canadian gas appliance standards:

• ANSI Z21.88-2017 / CSA 2.33-2017 - Vented Gas Fireplace Heaters

• CAN/CSA 2.17-2017 - Gas-Fired Appliance for Use at High Altitudes

• CSA P.4.1-15 - Testing Method for Measuring Annual Fireplace Eciency

STEADY STATE EFFICIENCY

Steady State Eciency - High Ey

SS,H

71.01%

Fireplace Eciency FE 60.72%

180-CL2118.SP.1 v1.00 June 30, 2020

Page 7

CL2118.SP.1

CERTIFICATION LABEL

Model: Clarity CL2118 top vent appliance

Modèle: Clarity CL2118 appareil de ventilation vers le haut

oNATURAL GAS oLP GAS

Orice (DMS) 0-1372 m 39 1.5 mm

Input rating / Puissance d’entrée (BTU/hr / Kw ) 0-1370m 0-4,500 ft Alt.

Minimum Input / Entrée Minimum (BTU/hr / Kw)

Manifold Pressure High setting / Manifold Pression réglé à High (In w.c. / kPa)

Manifold Pressure Low setting / Manifold Pression réglé à Low (In w.c. / kPa)

Minimum Inlet Pressure / Pression minimum d'admission (In w.c. / kPa)

27,300 / 8.00

14,838 / 4.35

3.8 / 0.95

1.0 / 0.25

7.0 / 1.74

26,200 / 7.68

14,120 / 4.14

10.6 / 2.64

2.9 /0.72

11.0 / 2.74

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1 / NFPA 54, or the Natural

Gas and Propane Installation Code, CSA B149.1.

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage Refer to the owner's manual

provided with this appliance. For assistance or additional information consult a qualied installer, service agency, or the gas supplier.

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having ammable vapors away. Keep burner and

control compartment clean. See installation and operating instructions accompanying appliance. VENTED GAS FIREPLACE HEATER —NOT FOR

USE WITH SOLID FUEL. For use with glass doors certied with the appliance only. Do not operate this appliance with glass removed, cracked or

broken. Replacement of the panel(s) should only be done by a qualied person. For use only with barrier Part No. 645.1821. Also for use in OEM /

mobile(manufactured) homes after home is on site. Convertible for use with natural gas or propane as follows: For natural gas when equipped with

orice #39; For propane when equipped with orice 1.5 mm. May be installed in a bedroom or sitting room when installed with a listed thermostat control

in Canada.

CLARITY CL2118.SP o CLARITY CL2118.IPI o

Listed vented gas replace heater / Poêle certié au gaz avec évacuation

MODEL / MODÈLE: Clarity CL2118 top venting appliance / Clarity CL2118 appareil ventilé vers le haut

This stove is factory equipped for 0-1372 m (0-4500 ft) / Ce poêle est manufacturé et équipé pour 0-1372 m (0-4500 pied)

UNITED STATES AND CANADA / ÉTATS-UNIS ET LE CANADA: Conforms to ANSI Z21.88-2017; Certied to CSA 2.33-2017 - Vented Gas

Fireplace Heater ,CSA 2.17-2017 - Gas-Fired Appliance For Use At High Altitudes. Conforme à ANSI Z21.88-2017; Certié CSA 2.33-2017 -

Poêle au gaz avec évent et CSA 2.17-2017 - Appareils de chauage au gaz utilisés en hautes altitudes.

SN - 26.

Cet appareil doit être installé selon les codes locaux, s’il y en a: sinon suivez l’actuel ANSI Z223.1 / NFPA 54 ou Gaz Naturel et Propane Codes, CSA

B149.1.

MISE EN GARDE: Une mauvaise installation, un ajustement, une altération, service ou entretien peuvent causer des blessures ou des dommages à la

propriété. Consultez le manuel du propriétaire fourni avec cet appareil. Pour assistance ou information additionnelle, consultez un installateur qualié,

agence de service ou votre fournisseur de gaz. Chaud lorsque l’appareil fonctionne. Ne pas toucher. Tenir loin des enfants, vêtements, meubles, essence

et autres liquides ayant des vapeurs inammables. Tenir le compartiment du brûleur et de contrôle propre. Voir les instructions de l’installation et du

fonctionnement accompagnant cet appareil. FOYER AU GAZ AVEC ÉVENT —NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE. Utiliser seulement

avec des portes vitrées certiées pour cet appareil. Ne pas opérer cet appareil, si la vitre est manquante, craquée, ou brisée. Le remplacement des

panneaux de verre seulement être fait par une personne qualiée. À utiliser uniquement avec le numéro de pièce de barrière 645.1821. Aussi pour l'usage

dans les maisons mobiles (manufacturées) après que la maison soit installée sur le site. Pouvant être converti pour usage avec le gaz naturel ou le

propane comme suit: Pour le gaz naturel une fois équipé d'un orice # 39.; Pour le propane une fois équipé de l'orice # 1.5 mm. Peut être installé dans

une chambre à coucher ou un salon une fois installé avec un thermostat approuvé au Canada.

MINIMUM CLEARANCES TO COMBUSTIBLES /

DÉGAGEMENTS MINIMUM REQUIS ENTRE L’APPAREIL ET DES MATÉRIAUX COMBUSTIBLES

Unit to sidewall / de l’unité au mur latéral 4” (102 mm)

Unit to back wall / de l’unité au mur arrière 4” (102 mm)

Unit corner to sidewall / du coin de l’unité au mur latéral 4” (102 mm)

Unit to ceiling (top vent & rear vent with snorkel) /

de l’unité jusqu’en haut (évacuation sur le dessus et par l’arrière avec ens, périscopique (snorkel))

32” (813 mm )

Unit to ceiling (2' up & out vent) / unité jusqu’en haut (2’ au- dessus et au- dessous de l’évacuation) 45” (1143 mm )

Vertical Vent / verticale évacuation murale extérieure

1” (25 mm) from outside surface / de la surface

extérieure

Horizontal Vent / horizontal évacuation murale extérieure

13" (330 mm) above / au dessus

2.5" (64 mm) beside / à côté de

1" (26 mm) below / au dessous de

Floor clearance / Dégagements pour la surface de plancher 0" (0 mm)

NOTE: CHECK LOCAL CODES FOR FLOOR REQUIREMENTS. THIS FIREPLACE IS SUITABLE FOR INSTALLATION ON A COMBUSTIBLE SURFACE.

VÉRIFIER LES CODES LOCAUX POUR ÉQUIPEMENT DE SURFACE DE PLANCHER, CET APPAREIL PEUT ÊTRE INSTALLÉ SUR UNE SURFACE COMBUSTIBLE

PFS Report#

F19-559

Electrical Rating: 115 Volts, 0.7 Amp, 60 Hz

DANGER: Risk of electrical shock. Disconnect power before servicing unit. Do not route power cord beneath heater. This appliance must be installed

in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title

24CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI / NCSBCSA 225.1 / NFPA501A, Manufactured Home Installations

Standard. This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located,

manufactured(mobile) home where not prohibited by local codes. See owners manual for details. This appliance is not convertible for use with other

gases unless a certied kit is used. This vented gas replace is not for use with air lters.

Caractéristiques électriques: 115 Volts, 0.7 Amp, 60 Hz

DANGER: Risque d’électrocution. Débrancher le courant avant de réparer l’unité. Ne pas mettre le cordon d’alimentation en dessous de l’appareil de

chauage. Cet appareil doit être installé selon les codes CAN/CSA Z240 MH, maisons mobiles (manufacturées), au Canada, sinon applicable, utilisez ANSI

/ NCSBCS A225.1/NFPA 501 A, Installation d’une maison mobile standard.

Cet appareil peut être utilisé seulement avec le type de gaz indiqué sur la plaque de contrôle et peut être installé dans un marché des accessoires, maison

(mobile) de manière permanente placée et manufacturée où ils ne sont pas interdit par des codes. Voir le manuel d’installation pour des détails. Cet

appareil ne peut pas être converti pour l'usage avec d'autres gaz à moins qu'un kit de conversion certié soit employé. Ce foyer au gaz à évacuation ne

pas être utilisé avec des ltres à air.

MANUFACTURED IN:

o USA: Blaze King Industries 146A Street, Walla Walla, WA. 99362

o CANADA: Valley Comfort Systems 1290 Commercial Way, Penticton, B.C. V2A 3H5

CSA P.4.1-15 Fireplace Eciency (FE) / Ecacité énergetique des foyer (EEF) CSA P.4.1-15:

CL2118.IPI Natural Gas / Gaz naturel: 62.04%

CL2118.SP Natural Gas / Gaz naturel: 60.72%

MANUFACTURE DATE

JAN o FEB o MAR o APR o MAY o JUN o

JUL o AUG o SEP o OCT o NOV o DEC o

2020 o 2021 o 2022 o 2023 o 2024 o 2025 o

170-0250 [01 20]

180-CL2118.SP.1 v1.00 June 30, 2020

Page 8

CL2118.SP.1

13"

FRONT FACING OFFSETS

VERT

VENT

REAR

VENT

GAS

INLET

OPTIONAL

ELECTRICAL

ACCESS

13"

OPTIONAL

GAS INLET

OPENING

ELECTRICAL

ACCESS

NOTE: TURNING ON YOUR APPLIANCE WHEN IT HAS BEEN OFF FOR AWHILE MAY CAUSE CONDENSATION

TO APPEAR ON THE GLASS. THIS IS A NORMAL OCCURRENCE AS YOUR APPLIANCE HEATS UP.

CLEARANCE TO COMBUSTIBLES

Side of unit to sidewall 4” (102 mm)

Back of unit to back wall 4” (102 mm)

Corner of unit to sidewall 4” (102 mm)

Top of unit to ceiling (top vent & rear vent with snorkel) 32” (813 mm)

Top of unit to ceiling (2’0” up and out vent) 45” (1143 mm)

Vertical Vent 1” (25 mm) from outside surface

Horizontal Vent

13” (330 mm) above / au dessus

2.5” (64 mm) beside / à côté de

1” (26 mm) below / au dessous de

Floor clearance 0” (0 mm)

DIMENSIONS

180-CL2118.SP.1 v1.00 June 30, 2020

Page 9

CL2118.SP.1

WARNING: If you do not follow these instructions exactly, a  re or explosion may result

causing property damage, personal injury or loss of life.

FOR YOUR SAFETY, READ BEFORE LIGHTING

A. This appliance has a pilot which is lit with a push button piezo lighter. When lighting the pilot, follow these

instructions exactly.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the  oor

because some gas is heavier than air and will settle on the  oor.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas suppliers instructions.

• If you cannot reach your gas supplier, call the  re department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or

turn by hand, don’t try to repair it, call a quali ed service technician. Force or attempted repair may result

in a  re or explosion.

D Do not use this appliance if any part has been under water. Immediately call a quali ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Set the thermostat to the lowest setting.

3. Valve controls are accessed by lowering the hinged panel that is below the  rebox.

4. Set the manual burner switch to the “OFF” position.

5. Push in gas control knob slightly and turn clockwise

to “OFF”.

6. Wait  ve (5) minutes to clear out any gas. Then smell for gas, including near the  oor. If you smell gas,

STOP! Follow “B” in the safety information above. If you don’t smell gas, go to the next step.

7. Turn control knob counterclockwise

to “PILOT” position.

8. Depress control knob and push in Piezo ignitor button. Once pilot ignites, continue to hold the control

knob in for about one (1) minute after the pilot is lit. Release knob and it will pop back up.

Pilot should remain lit. If it goes out, repeat steps 6 through 8.

• If knob does not pop up when released, stop and immediately call your service technician or gas

supplier.

• If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service

technician or gas supplier.

9. Turn gas control knob counter clockwise

to “ON”. Turn on all electric power to the appliance. Set

thermostat to the desired setting or set the manual burner switch to the “ON” position.

TO TURN OFF GAS TO THE APPLIANCE

1. Set the thermostat to the lowest setting.

2. Turn o all electric power to the appliance if service is to be performed.

3. Push in gas control knob slightly and turn clockwise

to “OFF”. Do not force.

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury

or property damage. Refer to the owner’s

information manual provided with this appliance.

For assistance or additional information, consult

a quali ed installer, service agency or your gas

supplier.

170-0360 [03 18]

LIGHTING INSTRUCTIONS

180-CL2118.SP.1 v1.00 June 30, 2020

Page 10

CL2118.SP.1

820 NOVA VALVE

TP TH

820 NOVA VALVE

1 ON/PILOT/OFF Knob

2 Manual HI-LO adjustment or pressure regulator adjustment

3 Pilot adjustment

4 Thermocouple connection

5 Mounting for piezo & bracket

6 Inlet pressure test point

7 Outlet pressure test point

8 Main operator

9 Pilot outlet

10 Main gas outlet

11 Flange mounting screw holes

12 Additional valve mounting holes

13 Alternative TC connection point

14 Thermoelectric unit

15 Inlet

180-CL2118.SP.1 v1.00 June 30, 2020

Page 11

CL2118.SP.1

OPERATING INSTRUCTIONS

PILOT LIGHT

Refer to the lighting instruction label on how to light

the pilot. Check that the pilot has fully engulfed the

thermocouple assembly (Fig.1).

LIGHTING THE BURNER

Standing Pilot (SP)

The CLARITY CL2118 SP controls are located behind

the hinged ap beneath the rebox.(Fig.2) To light

the burner follow the steps below:

1. Make sure the pilot is lit (see “LIGHTING

INSTRUCTIONS Standing Pilot”)

2. Turn the “Valve Control” knob counterclockwise

to ON.

3. Flip the ame ON/OFF switch, located beside the

igniter to ON.(Fig.3)

4. Turn the “Flame Height” knob to the desired

ame height.(Fig.2)

5. Turn on all electrical power to the unit.

6. NOTE: Burn the appliance on high, with the

optional blower OFF, for the rst two to three

hours. This will cure all the paint, gasket, and

seals. It is advised to open a door or window

as the unit will smoke and give o odors as it is

curing.

OPTIONAL BLOWER

An optional blower is available for the CLARITY

CL2118 SP and CLARITY CL2118 IPI, the S.Z5277.

SP and S.Z5277.IPI blower kits respectively. For

installation refer to the installation instructions

provided with the kit.

Turn the blower on by turning the “Fan speed”

knob clockwise .(Fig.2) The blower will only

come on when the replace is up to temperature

(approximately 10-15 minutes). Fan speed control

sequence is o, then maximum to minimum. The

speed of the fan can be decreased by turning the

knob clockwise . The speed of the fan can be

increased by turning the knob counterclockwise

. The blower will continue to operate after the burner

is turned o (approximately 15-20 minutes). To turn

the blower o manually, turn the fan control knob

counterclockwise until it “clicks”.

Fig.2

Fig.3

Fig.1

180-CL2118.SP.1 v1.00 June 30, 2020

Page 12

CL2118.SP.1

MAINTENANCE and SERVICE

ROUTINE MAINTENANCE

Regularly:

• Clean and remove any lint accumulations or debris from the grills and combustion or convection air

passage ways.

• Keep the appliance area free from combustible materials, such as paper, wood, clothing, gasoline,

ammable solids, liquids and vapors.

• Visually check the height and color of the burner and pilot ames. The pilot ame should be blue with

little or no yellow on the tips.

• Check for unusual noises or odors during operation of the appliance.

• Check the vent terminal for any damage, or obstruction by plants or debris accumulation.

It is recommended to periodically have your appliance serviced by a qualied service technician:

1. Remove the glass door (see “GLASS DOOR REMOVAL” on next page) and clean the inside of the

glass with a soft, non-abrasive cloth and water or a suitable, mild, non-abrasive cleaner.

2. Remove and clean the glass oor panel and set aside.

3. Remove and clean the oor panel assembly, check the burner to see if all the ports are clear and clean.

Check the pilot assembly to make sure it is not blocked by anything. Use a vacuum to clear out any

debris around the burner and valve.

4. Completely inspect the appliance and the venting system.

5. Check the safety system of the gas valve.

CLEANING SURFACES

Painted, powder coated, or porcelain enameled surfaces should be wiped with a damp cloth periodically.

Ensure the appliance has cooled down completely before any cleaning. Do not use other cleaners as they

may leave a residue which can become permanently etched into the surface.

CLEANING THE GLASS

DO NOT TO CLEAN THE GLASS WHILE IT IS HOT

One of the by-products of combustion and moisture in the rebox is a white lm which can show up on the

glass of the viewing door. Initial curing of the appliance can also leave a slight lm on the glass, which is a

temporary problem.

1. Turn o the appliance and allow it to cool down completely.

2. Remove the glass door from the rebox (see “GLASS DOOR REMOVAL” on next page)

3. Check the gasket material on the back of the glass. Ensure that it is attached and intact.

4. Clean the glass with a mild glass cleaner and a soft cloth (see below). Abrasive cleaners will damage

the glass

Slight soiling of SCHOTT ROBAX® panels can be removed using conventional glass cleaning products,

provided they are used according to instructions of use, which means cleaning on cold surfaces. The residues

should be removed since chemical attack is possible on exposure to temperature. The coated ROBAX®

Mirror, ROBAX® TrueView, ROBAX® IR Max and ROBAX® Energy Plus can be cleaned with a soft cloth.

NOTE: IT IS NOT RECOMMENDED TO USE SCOURING PADS, ABRASIVE CLEANSERS OR SCOURING

AGENTS, AS MAY CAUSE DAMAGE TO THE GLASS SURFACE. THE SCHOTT-RECOMMENDED DRY

WIPER IS SUITABLE FOR USE ONLY ON UNCOATED FIRE VIEWING PANELS.

180-CL2118.SP.1 v1.00 June 30, 2020

Page 13

CL2118.SP.1

MAINTENANCE and SERVICE

GLASS DOOR REMOVAL

For installation, cleaning, and burner removal the

glass door must be removed.

1. Turn o the appliance and allow it to cool

down completely.

2. Lift the face trim up and out, away from the

appliance, and set it aside.(Fig.4)

3. Lift the safety screen up and out, away

from the appliance, and set it aside. (Fig.5)

4. There are two door latch mechanisms on

top of the glass door.(Fig.6) Pull the tabs

forward and up o the door tabs.

Fig.4

Fig.5

Fig.6

180-CL2118.SP.1 v1.00 June 30, 2020

Page 14

CL2118.SP.1

5. Carefully slide the door glass assembly up

and out of the unit.(Fig.7)

GLASS DOOR REPLACEMENT

This glass in this appliance is a 5 mm high

temperature ceramic glass that will easily

withstand the heat that is produced. In the event

the glass breaks or cracks, contact your dealer

to arrange for your glass door replaced with a

factory replacement (see “PARTS LIST”). Do

not operate this appliance with the glass front

removed, cracked, or broken. Removal and

replacement of the glass from the door must be

done by a qualied service technician. The glass

door must be purchased from a Blaze King dealer.

No substitute materials are allowed.

BURNER REMOVAL

1. Turn o the appliance and allow it to cool down

completely.

2. Remove the face trim, safety screen, and glass

door. (see “GLASS DOOR REMOVAL” on

previoius page)

3. Remove the glass oor plate and set it aside.

(Fig.8)

4. Remove the oor plate assembly and set it

aside.(Fig.8)

5. Remove the screw from the left hand side of

the burner assembly.(Fig.9)

6. Move the burner to the right, up, and out.

To re-install the burner follow steps 1 to 7 in

reverse. Ensure the burner is centered in the

curved burner slot of the oor plate.

Fig.7

Fig.8

GLASS FLOOR PLATE

FLOOR PLATE

Fig.9

SCREW

BURNER

MAINTENANCE and SERVICE

180-CL2118.SP.1 v1.00 June 30, 2020

Page 15

CL2118.SP.1

MAINTENANCE and SERVICE

SAFETY SCREEN REPLACEMENT

The CLARITY CL2118 is supplied with a safety

screen pre-installed inside the door trim. If the

safety screen becomes damaged it must be

replaced with part #645.1821

1. Turn o the appliance and allow it to cool down

completely.

2. Remove the face trim and safety screen

by lifting up and out. (see “GLASS DOOR

REMOVAL”)

3. Slide the safety screen out of the frame, the

tabs may have to be adjusted. (Fig.10)

4. Slide the new safety screen in between the

frame face and the tabs. Ensure screen mesh

faces out, furthest from glass. (see image

below)

5. Hang the safety screen back into position.

6. Hang the face trim back into position.

SCREEN

MESH TO

THIS

SIDE

Fig.10

180-CL2118.SP.1 v1.00 June 30, 2020

Page 16

CL2118.SP.1

FUEL CONVERSION

THIS CONVERSION KIT SHALL BE INSTALLED BY A QUALIFIED SERVICE AGENCY IN

ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS AND ALL APPLICABLE CODES AND

REQUIREMENTS OF THE AUTHORITIES HAVING JURISDICTION. IF THE INFORMATION IN THESE

INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE, EXPLOSION OR PRODUCTION OF CARBON

MONOXIDE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF

LIFE. THE QUALIFIED SERVICE AGENCY IS RESPONSIBLE FOR THE PROPER INSTALLATION OF

THE KIT. THE INSTALLATION IS NOT COMPLETE UNTIL THE OPERATION OF THE CONVERTED

APPLIANCE IS CHECKED AS SPECIFIED IN THE INSTRUCTION MANUAL SUPPLIED WITH THE

KIT. BEFORE PERFORMING THIS OR ANY SERVICE PROCEDURE, MAKE SURE THAT THE GAS

SUPPLY TO THE UNIT AND THE ELECTRICAL SUPPLY ARE SHUT OFF.

CONVERSION KIT CONTENTS

The conversion kit contains the following parts:

• S.Z0760 (LPG)> #635.OR1.5 (1.5 mm orice) and LPG regulator.

• S.Z0761 (NG)> #635.OR39 (#39 orice) and NG regulator.

• Conversion Kit labels.

To convert from NG to LPG or reverse:

1. Turn o the appliance and allow it to cool down completely

2. Remove burner (see “BURNER REMOVAL” on previous page)

3. Replace main orice

4. Convert pilot fuel (see below)

5. Replace regulator (see next page)

How to convert CLARITY CL2118 SP Pilot orice:

1. Use a 7/16” wrench to loosen the pilot hood.

2. Push the little tab in and the little tab with hole should pop out. The hole stamp tab (LP) out is used for

Propane. The stamped tab (NA) out is for Natural Gas.

3. Re-tighten the pilot hood.

4. Fill out the fuel conversion label and ax between the two labels on the control panel door.

All valves have been pre-set and certied for installation at elevations from 0 – 4500 feet (1 – 1372m) above

sea level.

HIGH ELEVATIONS

When installing this unit at higher elevations, it is necessary to decrease the input rating by replacing the

existing burner orice with a smaller size for installations over 4500 feet (1370 m). Above 4500 ft, the

appliance input should be reduced 4% for each additional 1000 feet (305m). For the USA, derate the unit

according to the gas installation code.

MAINTENANCE and SERVICE

180-CL2118.SP.1 v1.00 June 30, 2020

Page 17

CL2118.SP.1

820 NOVA

installationi

HI/LO Conversion Kit

WARNING!

The installation of this conversion kit must only be undertaken by a

qualified and certified gas appliance installer.

WARNING!

This HI-LO conversion kit must ONLY be applied as part of a conversion kit

supplied by the APPLIANCE MANUFACTURER for the specific appliance, and

type of gas, being converted.

INSTALLER NOTICE. These instructions must be left with appliance.

This installation or replacement instruction refer to HI-LO pressure

regulator kit to be used to convert the 820 Nova Combination Gas Control

with adjustable pressure regulator into manual HI-LO. The same kit can

also be used for the conversion from LP to Natural Gas and vice versa of

the 820 Nova with manual HI-LO.

7.252.021 001

Turn control knob to the OFF position,

and shut off the gas supply to the

valve.

Using a Torx T20, or slotted screwdriver,

remove and discard the three pressure

regulator mounting screws (A), pressure

regulator tower (B), and the spring and

diaphragm assembly (C).

Ensure the rubber gasket (D), which is

prefitted as part of assembly (E), is

properly positioned and install the new

HI/LO pressure regulator assemble

using the supplied screws (F).

Tighten screws securely.

(Reference torque = 25 lb·in).

Install the enclosed identification label

(G) to the valve body where it can be

easily seen.

Apply gas to system and re-light

appliance according to manufacturers

instructions.

With the main burner “ON”, test the

new pressure regulator assembly for

leaks using a soap solution.

Relight the main burner in both the HI,

and LO positions, and verify proper

burner ignition and operation.

MAINTENANCE and SERVICE

180-CL2118.SP.1 v1.00 June 30, 2020

Page 18

CL2118.SP.1

INSTALLATION PLANNING

20" to 21"

(based on front

facing offsets)

METAL STUDS

* CLEARANCE TO COMBUSTIBLES

For a 2’0” vertical and 6” out vent conguration the ceiling clearance to combustibles is 71 3/8”

For a vertical vent conguration the ceiling clearance to combustibles is 58 3/8”

For a 9” horizontal to snorkel vent conguration the ceiling clearance to combustibles is 58 3/8”

FRAMING - ROUGH OPENING

The CL2118 appliance can be raised,

placed at oor level, or installed in a

corner. Please see specic framing

measurements for each situation

on the following pages. The basic

rough opening should have the

dimensions shown in Fig.11. Any

framing within specied combustion

clearances must be non-combustible

metal studs. Ensure the replace

has a strong and level surface to be

placed on. It can be made of wood

or a non-combustible material. Any

material such as studs must be non-

combustible if they are within the

clearances specied.

The gas line should be run to the

right side of the appliance, it is also

possible to run it to the left side if

needed. See “DIMENSIONS” for

gas inlet locations.

Fig.11

This section of the owner’s manual is for the use of qualied service technicians only. Fireplace placement,

hearths, and venting terminations will be covered, as well as the gas and electrical systems. Please read

“SAFETY PRECAUTIONS” at the front of this manual.

PRECAUTIONS

• The installation must conform to the installation codes.

• This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate

ventilation air. Provide adequate clearance around air openings of the appliance. Never obstruct front

openings.

• Provide adequate clearances for proper operation and servicing of the appliance.

• This appliance must be properly connected to a venting system.

• The venting of this appliance must be installed in a location that is free of plumbing, electrical wiring and

heating or air conditioning ducts.

Select a location that is accessible for venting.(see “ALLOWABLE TERMINATION LOCATIONS”)

180-CL2118.SP.1 v1.00 June 30, 2020

Page 19

CL2118.SP.1

INSTALLATION PLANNING

102mm

1112mm

1598mm

718mm

min. to metal studs

927mm

min. to wood studs

CLEARANCE TO

COMBUSTIBLES

FRAMING - CORNER INSTALLTION

The dimensions for installing the CL2118 appliance in a corner is shown in Fig.12. Do not interfere with

the structural integrity of the walls. Shown below are minimum clearances; increasing these dimensions is

allowable as long as vent length remains in the allowable range.

Fig.12

180-CL2118.SP.1 v1.00 June 30, 2020

Page 20

CL2118.SP.1

INSTALLATION PLANNING

WALL FINISH

Non-combustible cement board. The CL2118 appliance requires a 1/2” (13 mm) thick non-combustible

cement board to be used as a wall surface immediately surrounding the unit on each side (see Fig13. below)

for minimum coverage. Extending the cement board well beyond the minimum shown will help avoid cracking

due to dierential expansion of materials. Pre-drill cement board with oversized holes and do not over-tighten

screws to avoid cracking due to heat expansion. Standard gypsum wall board may be used beyond the

perimeter of the cement board.

Non-combustible nishing over cement board. Additional non-combustible material such as tile, etc., may

be applied over top of the cement board or you may choose to leave it nished clean with no tile—see next

page. Be aware that a trim is always required and the trims will accept tile, etc. behind them up to 1” thick,

depending on appliance side ange position. Additional non-combustible nishes, if desired, may be butted up

to the trims. Finish should not cover the trims as they need to remain removable.

58 3/8" or 71 3/8"

1483 mm or 1813 mm

Min. (see FRAMING

- ROUGH OPENING)

Min.

927mm

673mm

724mm

13mm

thick non-combustible

cement board

32" or 45"

813 mm or 1143 mm

(see CLEARANCE

TO COMBUSTIBLES)

BOARD FLUSH WITH BOTTOM

OF APPLIANCE; ADD EXTRA

IF OVERLAPPING FRAMING

GYPSUM

BOARD UP TO

PERIMETER OF

CEMENT BOARD

Fig.13

Page is loading ...

Blaze King Clarity 2118 SP Owner's manual

Brand: Blaze King

Model: Clarity 2118 SP

Category: Stoves

Type: Owner's manual

Download PDF

report

Blaze King Clarity 2118 SP Owner's manual

Blaze King Clarity 2118 SP Owner's manual

Related papers

Other documents