Montigo DRFK1 DRFK2 Fan Kit Operating instructions

Montigo
Brand
Montigo
Model
DRFK1 DRFK2 Fan Kit
Category
Fireplaces
Type
Operating instructions
XT0068 - 050619
Installation
DRFK1 DELRAY LINEAR FAN KIT
INSTALLATION
Assembly
1
3
4 6 8
9
5 7
2
Remove two (2) screws securing the pilot cover. Burner
can now be removed by pulling upwards.
Remove the rebox pan being secured with twenty (20) #8
tek screws. The pan can now be pulled forward and gently
rested on the front lip of the replace frame.
Connect the two (2) fans to the manual fan speed control
box. The fan speed control can be connected to the
existing harness.
Install the three (3) air deectors with attached magnets to
the replace door, taking note of spaces for door latches.
Re-install Pan, Deck, media tray and all burner and pilot
related parts. Ensure all screws are accounted for.
Remove adhesive backing from fan brackets. Place fans
against the back of the firebox next to the posts as
shown. Ensure the motors are facing in.
Remove adhesive backing from fan speed control,
attach to the inner front wall of fireplace. Heat sensor
can be attached to the bottom of the burner pan.
Remove the Media tray deck being secured with four (4) #8
tek screws.
The ten (10) screws that retain the media tray can now
be removed. Remove the two media tray(s) as shown
below.
Take care when manoeuvring burner pan to prevent damaging the gas
ex line and pilot wires. Removing the ex hose requires replacement
Some fans might come with the black & white wires in reverse position.
These are AC fans and are not aected by the polarity.
WARNING NOTICE
Fans rest agaist the
back wall of the
fireplace and next to
the support posts.
Be sure to leave
gap between fans
and post to prevent
vibration noise
Ensure the fans are
oriented with the
motors facing inward
FRONT OF FIREPLACE
EXISTING FAN HARNESS
LOCATED AT THE BOTTOM
OF THE FIREBOX
Fan EC1377 - left
Fan Heat Sensor
Fan Molex Connectors
Fan Molex Power
Connector
Fan Speed Control
Fan EC1378 - right Air Deflector(s)
XT0068 - 050619
Installation
DRFK2 DELRAY SQUARE FAN KIT
INSTALLATION
DRFK2 DELRAY SQUARE FAN KIT
INSTALLATION
Assembly
1
3
6 8
9
5
7
2
Remove two (2) screws securing the pilot cover. Burner
can now be removed by pulling upwards.
Connect the two (2) fans to the manual fan speed control
box. The fan speed control can be connected to the
existing harness.
Install the two (2) air deectors with attached magnets to
the top center of the replace door, taking note of spaces
for door latches.
Re-install Pan, Deck, media tray and all burner and pilot
related parts. Ensure all screws are accounted for.
Place fans in the rear corners of the firebox and secure
with two (2) screws. Ensure the motors are facing out.
Remove adhesive backing from fan speed control,
attach to the inner front wall of fireplace. Heat sensor
can be attached to the bottom of the burner pan.
Remove the Media tray deck being secured with
#8 tek screws.
The screws that retain the media tray can now be
removed. Remove the media tray as shown below.
Take care when manoeuvring burner pan to prevent damaging the gas
ex line and pilot wires. Removing the ex hose requires replacement
Some fans might come with the black & white wires in reverse position.
These are AC fans and are not aected by the polarity.
WARNING
NOTICE
EXISTING FAN HARNESS
LOCATED AT THE BOTTOM
OF THE FIREBOX
Fan EC1377 - left
Fan Heat Sensor
Fan Molex Connectors
Fan Molex Power
Connector
Fan Speed Control
Fan EC1378 - right Air Deflector(s)
  • Page 1 1
  • Page 2 2

Montigo DRFK1 DRFK2 Fan Kit Operating instructions

Montigo
Brand
Montigo
Model
DRFK1 DRFK2 Fan Kit
Category
Fireplaces
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents