Zoom Handy Recorder H4 Datasheet

Operation Manual

Reproduction of this manual, in whole or in part,

by any means, is prohibited.

English

H4_E.book 1 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

2

SAFETY PRECAUTIONS

In this manual, symbols are used to highlight warnings and

cautions for you to read so that accidents can be prevented. The

meanings of these symbols are as follows:

This symbol indicates explanations about extremely

dangerous matters. If users ignore this symbol and

handle the device the wrong way, serious injury or

death could result.

This symbol indicates explanations about dangerous

matters. If users ignore this symbol and handle the

device the wrong way, bodily injury and damage to

the equipment could result.

Please observe the following safety tips and precautions to

ensure hazard-free use of the H4.

Power requirements

Since power consumption of this unit is fairly high, we

recommend the use of an AC adapter whenever

possible. When powering the unit from batteries, use

only alkaline types.

[AC adapter operation]

• Be sure to use only an AC adapter which supplies 9 V DC,

300 mA and is equipped with a "center minus" plug

(Zoom AD-0006). The use of an adapter other than the

speciﬁed type may damage the unit and pose a safety

hazard.

• Connect the AC adapter only to an AC outlet that supplies

the rated voltage required by the adapter.

• When disconnecting the AC adapter from the AC outlet,

always grasp the adapter itself and do not pull at the cable.

• During lightning or when not using the unit for an

extended period, disconnect the AC adapter from the AC

outlet.

[Battery operation]

• Use two conventional IEC R6 (size AA) batteries

(alkaline).

• The H4 cannot be used for recharging.

•Pay close attention to the labelling of the battery to make

sure you choose the correct type.

• When not using the unit for an extended period, remove

the batteries from the unit.

• If battery leakage has occurred, wipe the battery

compartment and the battery terminals carefully to

remove all remnants of battery ﬂuid.

• While using the unit, the battery compartment cover

should be closed.

Environment

To prevent the risk of ﬁre, electric shock or

malfunction, avoid using your H4 in environments

where it will be exposed to:

• Extreme temperatures

• Heat sources such as radiators or stoves

• High humidity or moisture

• Excessive dust or sand

• Excessive vibration or shock

Handling

•Never place objects ﬁlled with liquids, such as vases, on

the H4 since this can cause electric shock.

• Do not place naked ﬂame sources, such as lighted candles,

on the H4 since this can cause ﬁre.

• The H4 is a precision instrument. Do not exert undue

pressure on the keys and other controls. Also take care not

to drop the unit, and do not subject it to shock or excessive

pressure.

•Take care that no foreign objects (coins or pins etc.) or

liquids can enter the unit.

Connecting cables and input and output

jacks

You should always turn off the power to the H4 and all

other equipment before connecting or disconnecting

any cables. Also make sure to disconnect all connection

cables and the power cord before moving the H4.

Alterations

Never open the case of the H4 or attempt to modify the

product in any way since this can result in damage to

the unit.

Volume

Do not use the H4 at a loud volume for a long time

since this can cause hearing impairment.

Usage Precautions

Electrical interference

For safety considerations, the H4 has been designed to provide

maximum protection against the emission of electromagnetic

radiation from inside the device, and protection from external

interference. However, equipment that is very susceptible to

interference or that emits powerful electromagnetic waves

should not be placed near the H4, as the possibility of

interference cannot be ruled out entirely.

With any type of digital control device, the H4 included,

electromagnetic interference can cause malfunctioning and can

corrupt or destroy data. Care should be taken to minimize the

risk of damage.

Cleaning

Use a soft, dry cloth to clean the H4. If necessary, slightly

moisten the cloth. Do not use abrasive cleanser, wax, or solvents

(such as paint thinner or cleaning alcohol), since these may dull

the ﬁnish or damage the surface.

Please keep this manual in a convenient place for

future reference.

W

arning

Caution

W

arning

W

arning

W

arning

Caution

W

arning

Caution

SAFETY PRECAUTIONS / Usage Precautions

Caution

H4_E.book 2 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

3

Contents

SAFETY PRECAUTIONS / Usage

Precautions ............................................2

Overview ...................................................5

Introducing the H4 ...................................6

Stereo Mode and 4-Track Mode ...........6

Mixer Functions .....................................7

Effects ....................................................7

Parts of the H4 .........................................8

Getting Connected .................................10

About SD Cards ......................................10

Operation on Battery Power .................11

Power On/Off ..........................................11

Power-on .............................................11

Power-off .............................................11

Recording ...............................................12

Setup ....................................................12

Recording steps ..................................12

Quick Guide 1

Stereo mode basic operation..............14

Preparations before recording ............14

Starting the H4 ....................................... 14

Adjusting the input sensitivity/recording

level ..................................................... 14

Using effects ........................................16

Recording ............................................17

Selecting a file for playback ...................18

Quick Guide 2

4-track mode basic operation ............19

Step 1: Preparations ............................19

Switch to 4-track mode .......................... 19

Creating a new project ........................... 20

Making metronome settings .................. 20

Step 2: Recording the first track .........21

Selecting the input source/recording

track ..................................................... 21

Adjusting the input sensitivity/recording

level ..................................................... 22

Selecting an effect patch .......................24

Recording/Playback ............................... 25

Step 3: Add more tracks ..................... 26

Preparations ........................................... 26

Recording/Playback ............................... 26

Step 4: Mixing and bounce ................. 27

Mixing .................................................... 27

Bounce ................................................... 28

Stereo Mode .......................................... 30

What is stereo mode? ......................... 30

Switching to stereo mode ................... 30

Recording in stereo mode .................. 31

Select input source ................................ 31

Adjust recording level ............................ 31

Automatic adjustment of recording level

(Auto gain function) ............................. 33

Select recording format ......................... 34

Record ................................................... 35

Using the monitor function .................... 36

Playback in stereo mode .................... 36

Selecting a file for playback ................... 36

Locating a point in a recording

(Locate) ................................................ 37

Playing a specified section repeatedly

(A-B repeat) ........................................ 38

4-Track Mode ......................................... 39

What is 4-track mode? ........................ 39

Switching to 4-track mode ................. 39

Selecting the recording mode ............ 40

About the recording mode ..................... 40

Selecting the recording mode ................ 41

Operation differences according to

recording mode ................................... 41

Recorder .............................................. 42

Selecting files for playback .................... 42

Using the locate function and A-B

repeat function in 4-track mode .......... 43

Re-recording only a specified region

(punch-in/out function) ........................ 43

Combining multiple tracks on one file

(bounce function) ................................. 45

Mixer .................................................... 47

About the mixer in 4-track mode ........... 47

Selecting the input source ..................... 48

Adjusting the recording level ................. 48

Selecting the recording track ................. 50

Using the monitor function .................... 51

4-track mixing (volume/panning) ........... 51

Linking two tracks (stereo link) .............. 53

H4_E.book 3 ページ２００６年９月１日　金曜日　午後７時５６分

Contents

ZOOM H4

4

Projects................................................ 54

What is a project? ...................................54

Basic project operations .........................54

Creating a new project ...........................55

Selecting a project ..................................55

Changing a project name .......................56

Copying a project ...................................57

Deleting a project ...................................57

Write-protecting a project ......................58

Tuner ....................................................59

Using the chromatic tuner ......................59

Using other tuner types ..........................60

Effects .....................................................62

About Effects .......................................62

Using effects in stereo mode ..............62

Using effects in 4-track mode .............64

About effect input/output .......................64

Selecting a patch ....................................64

Editing a patch ........................................65

Saving a patch ........................................67

Assigning a name to a patch ..................68

Importing a patch ...................................69

Managing Recorded Files ..................... 71

About recorded files ............................71

Basic file operations ............................71

Renaming a file ....................................72

Deleting a file .......................................73

Copying a file (4-track mode only) ......73

Importing a file (4-track mode only) ....74

Checking the file size ..........................76

Miscellaneous Settings ......................... 77

Metronome setting ..............................77

Controlling the display

contrast/backlight .............................78

Turning the phantom power supply

on/off .................................................79

Controlling the key-hold function .......79

Using the USB function .......................80

Using the H4 as audio interface for a

computer ..............................................80

Using the H4 as an SD card reader ........82

SD card operations ..............................83

Checking available space on the SD

card ......................................................83

Initializing an SD card .............................84

About the software version .................84

Specifications .........................................86

Troubleshooting .....................................88

Problems during recording/

playback ............................................ 88

Other problems ................................... 88

Effect Types and Parameters ................89

Effect types and parameters in

4-track mode ..................................... 89

PREAMP module ....................................89

EFX module ............................................91

Effect types in stereo mode ................ 95

MIC MODEL module ..............................95

COMP/LIMIT module ..............................95

H4 Patch List ..........................................96

Contents of SD Card ..............................97

INDEX ......................................................98

• Windows and Windows XP are registered

trademarks of Microsoft Corporation.

• Macintosh and MacOS are registered

trademarks of Apple Computer.

• The SD symbol is a trademark.

• All other trademarks, product names, and

company names mentioned in this

documentation are the property of their

respective owners.

• Manufacturer names and product names

mentioned in this documentation are

trademarks or registered trademarks of their

respective owners. The names are used only to

illustrate sonic characteristics and do not

indicate any afﬁliation with ZOOM

CORPORATION.

H4_E.book 4 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

5

Overview

Thank you for selecting the

ZOOM Handy Recorder H4

(subsequently referred to simply as the

"

H4

"). The H4 is an attractive product with the following features.

●

All-in-one type handy recorder

In a compact package weighing a mere 190 grams, the H4 offers a high-performance stereo

condenser mic, SD card recorder, mixer, effect section, metronome, and more. Easily record

and produce music on the go, wherever you are.

●

Applications range from field recording to multi-track use

The H4 offers a choice of stereo mode for instant stereo recording, and 4-track mode which

allows simultaneous playback of four tracks and recording of two tracks. Use the unit in the

field to capture your melody ideas, quickly record a band, or to expand your sound collection.

Or use it as a multi-track recorder to overdub instruments and vocals.

●

Convenient bounce function

Once you have recorded four tracks, you can bounce the contents onto a stereo or mono file. By

assigning the resulting file to a recorder track, you can then continue to add more instrument or

vocal parts using the remaining tracks. Recorded files can also be copied to a computer for

further processing or burning onto an audio CD.

●

Two types of effects built in

The H4 comes with two built-in effect modules. The PREAMP module simulates the

characteristics of famous guitar and bass amps as well as various mic preamps. The EFX

module offers chorus and other modulation effects and spatial effects such as delay. Since the

input signal can be effect processed before recording, all you need to do is directly hook up your

guitar and bass and you're in business.

●

Functions as audio interface or SD card reader for a computer

The USB port of the H4 lets you easily connect the unit to a computer, for use as an audio

interface with built-in effects. (Effects can only be used when the sampling rate is 44.1 kHz.)

Another option is to use the H4 as an SD card reader, to quickly transfer files for import into

DAW software or for creating audio CDs.

●

Built-in tuner and metronome

The integrated tuner not only allows chromatic tuning but also supports 7-string guitar, 5-string

bass and other unconventional tunings. The metronome function is great when doing multi-

track recordings or for use during practice sessions.

Please take the time to read this manual carefully to get the most out of the unit and

to ensure optimum performance and reliability.

Keep this manual at hand for future reference.

H4_E.book 5 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

6

Introducing the H4

This section explains the main features and functions of the H4.

Stereo Mode and 4-Track

Mode

The H4 has two main operation modes, namely

"stereo mode" and "4-track mode". You select

one of these modes when using the unit.

In stereo mode, two signals either from the built-

in stereo mic or from the [INPUT 1]/[INPUT 2]

jacks are used as recording sources to create a

stereo file on the SD card. This is great for

making full-fledged recordings in the field or to

capture the performance of a band in one go. It

also allows the H4 to be used as voice recorder

that's ready at a moment's notice.

You can select either WAV or MP3 as recording

format, and you can change the sampling rate

and bit rate as required. The recorded stereo files

are saved in a dedicated folder (hierarchical unit)

for the stereo mode. These files can be sent to a

computer via the USB port, for burning onto CD-

R/RW discs or for processing with DAW

software.

In 4-track mode, the H4 functions as a multi-

track recorder. This mode allows simultaneous

recording of 2 tracks and simultaneous playback

of 4 tracks. This lets you do things such as

creating a backing of drum machine and bass and

then produce a guitar or vocal overlay in the

studio.

After recording all four tracks, the individual

volume and panning (left/right positioning) of

each track can be adjusted for playback, and a

stereo or mono file can be created on the SD

card. By assigning the resulting file to a

particular track, you can free up the remaining

tracks to record more instruments or vocals to

create an overlay.

The recording format is fixed to WAV (sampling

rate 44.1 kHz/bit rate 16 bit). The individual files

created by recording in 4-track mode are saved

on the SD card in separate folders for each

project.

Recorder

Input 1

Input 2

Built-in

stereo mic

or

[INPUT 1] jack

[INPUT 2] jack

Stereo mode

L stereo track

R stereo track

SD card

Files recorded in

stereo mode are

saved here

Dedicated stereo

mode folder

Input 1

Input 2

Built-in

stereo mic

or

[INPUT 1] jack

[INPUT 2] jack

Recorder

4-track mode

Track 1

Input

mixer

Track 2

Track 3

Track 4

SD card

Files recorded in

4-track mode for

project 2 are saved

here

Project 1 folder

Project 2 folder

Project 3 folder

H4_E.book 6 ページ２００６年９月１日　金曜日　午後７時５６分

Introducing the H4

ZOOM H4

7

Mixer Functions

When the H4 is operating in 4-track mode, two

kinds of mixers can be used, namely the input

mixer and track mixer.

The input mixer takes up to two signals from the

built-in stereo mic or the [INPUT 1]/[INPUT 2]

jacks and sends them on in mixed form or

separately to the recorder tracks.

The track mixer adjusts the volume and panning/

balance of each signal recorded on the four

tracks and produces a stereo output signal.

Effects

The H4 also incorporates an effect section

immediately after the input that can be used to

process the input signal before recording it on the

tracks.

The effect section of the H4 offers multiple

single effects (effect modules) such as

compressor and preamp. The available effect

module configuration and input/output

specifications depend on the operation mode.

In stereo mode, the two effect modules MIC

MODEL and COMP/LIMIT can be used. (The

MIC MODEL module can be used only if the

built-in stereo mic is selected as input source.) In

this mode, both effect input and effect output are

in stereo.

In 4-track mode, the two effect modules

PREAMP and EFX can be used. In this mode,

the effect input is monaural and the effect output

is in stereo. (If only one track is selected as

recording target, the signal will be combined to

mono immediately after the effect section.)

Input 1

Input 2

[LINE OUTPUT] jack

Recorder

Track mixer

(for volume and panning)

Input

mixer

Track 1

Track 2

Track 3

Track 4

Recorder

Input 1

Input 2

Input 1

Input 2

Stereo mode

4-track mode

L stereo track

R stereo track

Recorder

Track 1

Input

mixer

Effect

section

Effect

section

Track 2

Track 3

Track 4

Stereo mode module configuration

(Stereo input → Stereo output)

MIC MODEL COMP/LIMIT

4-track mode module configuration

(Mono input → Stereo output)

PREAMP EFX

H4_E.book 7 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

8

Parts of the H4

Left side panel

[LINE OUTPUT]

jack

Top panel

Built-in stereo mic

[REC] key

[ACCESS]

indicator

[MODE]

indicator

Rear panel

[INPUT 1] jack

[INPUT 2] jack

Display

TRACK

[1] – [4] keys

[MENU] key

[PHONES]

jack

[PHONES LEVEL]

knob

[DC IN] jack

[POWER]

switch

[USB]

port

H4_E.book 8 ページ２００６年９月１日　金曜日　午後７時５６分

Parts of the H4

ZOOM H4

9

Front panel

Right side panel

Jog dial

[MIC GAIN]

switch

[INPUT 2 GAIN]

switch

[INPUT 1 GAIN]

switch

[SD CARD] slot

Battery compartment

cover

Opening the battery compartment cover

(1)

Slide the section with

your index finger to release

the lock.

(1)

(2)

(3)

(2)

(2) With the lock released,

grasp the cover with your

thumb and middle finger

and lift it.

(3) Flip the cover open

in the forward direction.

Battery Battery

(1)

(2)

(3)

H4_E.book 9 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

10

Getting Connected

For using the H4, an SD card is required as a

recording medium. Before turning power to the

H4 on, insert the card into the [SD CARD] slot as

shown in the illustration below. Be sure to push

the card fully into the slot. To remove the card,

first push it into the slot to disengage and then

pull it out.

NOTE

• If the SD card is inserted with wrong

orientation, it will not go all the way into the

slot.

• Never insert or remove the SD card while power

to the H4 is on. Otherwise data can be

destroyed.

•You can use off-the-shelf SD cards with a

capacity from 16 MB to 2 GB.

•To use a SD card that has previously been

initialized in a computer or digital camera or

similar, be sure to format in the H4 ﬁrst

(

→

p. 84).

• If an operation requiring an SD card is

attempted while no SD card is inserted, the

indication "No Card" appears.

About SD Cards

When the H4 is connected to a

computer via the [USB] port, it can be

used as audio interface or SD card

reader for the computer, and audio

files stored on the SD card in the H4

can be transferred to the computer.

To monitor the output of

the H4 with a stereo

audio system, use a Y

cable connected to the

[LINE OUTPUT] jack.

To monitor the output of the H4

with headphones, connect them to

the [PHONES] jack and adjust the

listening level with the [PHONES

LEVEL] knob. This jack carries the

same signal as the [LINE OUTPUT]

jack.

To operate the H4 on AC power, be

sure to use only the supplied AC

adapter (ZOOM AD-0006). Using a

different adapter can lead to damage.

The [INPUT 1]/[INPUT 2] jacks can be used to connect external

equipment such as a mic, bass, guitar, or keyboard.

AC adapter

Monitor

system

Bass

Mic

Keyboard

Computer

Headphones

H4 side panel

H4 rear panel

Guitar

[SD CARD]

slot

SD card

SD

H4_E.fm 10 ページ２００６年９月１日　金曜日　午後８時１６分

ZOOM H4

11

Operation on Battery Power

The H4 can be powered from batteries which must be purchased separately. Insert the batteries as

follows.

1.

Open the battery compartment cover

as described on page 9.

2.

Insert two IEC R6 (size AA) batteries.

3.

Close the battery compartment cover.

NOTE

• When the unit is operated on batteries, the

indication "Low Battery!" will appear on the

display when the batteries are exhausted. In

this case, turn the unit off and replace the

batteries as soon as possible with fresh ones.

• When the unit is operated on batteries, you

should not open the battery compartment

cover while power is on. Otherwise the sudden

interruption of power may lead to data loss.

Power On/Off

Use the following procedure to turn the H4 on and off.

Power-on

1.

Verify that power to the H4 and any

peripheral equipment is off.

Turn down the volume control on connected

instruments, the H4, and the monitoring

system.

2.

Insert the SD card into the [SD

CARD] slot (

→

p. 10).

3.

Set the [POWER] switch on the H4

to On.

NOTE

• If the indication "No Card" appears at startup,

the H4 has not detected an SD card. Verify

that an SD card is correctly inserted.

• If the indication "Format Card?" appears at

startup, the H4 has detected that the SD card

is not initialized. To execute the initialization

process, bring the cursor to the OK button

and press the jog dial.

4.

Turn power to other equipment on

in the order connected instruments

→

monitoring system.

Power-off

1.

Turn power to other equipment off

in the order monitoring system

→

connected instruments.

2.

Set the [POWER] switch on the H4

to Off.

The message "GoodBye See You!" is shown on

the display and the H4 is turned off.

Information about current operations is

automatically saved on the SD card.

NOTE

• Always use the [POWER] switch to turn the

unit on and off.

• Never disconnect or connect the AC adapter

while power is on. Otherwise data loss may

occur.

• In particular, do not plug in or unplug the AC

adapter while the [ACCESS] indicator is lit.

Otherwise data can be destroyed.

H4_E.book 11 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

12

Recording

This section shows how you can try out the H4 straight away by doing some recording. The steps are for

using the stereo mode with the built-in stereo mic.

Setup

To record on-mic, place the sound source at

about 30 to 50 centimeters from the H4.

To record off-mic, the sound source should be

within the range of the two intersecting lines

from the two built-in mics.

If the H4 is placed directly on the floor, it may

pick up the sound of footsteps, drum vibrations

etc. You should therefore place the H4 on a table

or a chair, or use a tripod with the supplied

adapter.

Recording steps

1.

Turn power to the H4 on.

2.

The [MODE] indicator lights up.

Verify that the H4 is set to stereo

mode.

If the [MODE] indicator is out, the H4 is in

4-track mode. Switch it to stereo mode

(

→

p. 30).

3.

Verify that the following indication is

shown on the display.

This is the top screen for the stereo mode. If

another screen is shown, repeatedly press the

center of the [MENU] key until the above screen

appears.

On-mic recording

About

30 – 50 cm

Built-in stereo mic

Sound

source

Off-mic recording

Built-in

stereo mic

Lit

Stereo mode

H4_E.book 12 ページ２００６年９月１日　金曜日　午後７時５６分

Recording

ZOOM H4

13

4.

Use the TRACK [1] – [4] keys to

select the recording format.

The recording format selected by each key is as

shown below. Recording quality and file size

decrease from top to bottom.

Press the key for the desired format and sampling

rate, so that the key lights up. Then press the

center of the [MENU] key repeatedly until to

return to the top screen of the stereo mode.

HINT

If required, you can also change the bit rate

(resolution) of the recording format.

5.

Press the [REC] key.

The [REC] key flashes and the H4 goes into

record standby mode. The display now operates

as a level meter showing the input level from the

built-in stereo mic. The input signal can be

monitored via the [LINE OUTPUT] jack and

[PHONES] jack.

6.

To obtain optimum volume levels, set

the [MIC GAIN] switch so that the

meter indication on the display stays

just below 0.

●

[MIC GAIN] switch setting

HINT

You can fine adjust the recording level manually

or automatically (

→

p. 31, 33).

NOTE

If the level meter does not register at all when the

unit is pointed towards the sound source and the

unit shows the above screen, the [INPUT 1]/

[INPUT 2] jacks may be selected as input source.

Switch the input source to the built-in stereo mic

(

→

p. 31).

7.

Press the [REC] key once more.

The [REC] key lights up and recording starts.

8.

To stop recording, press the [REC]

key or press the top (@

) of the

[MENU] key.

9.

To check the recorded content,

press the top (@

) of the [MENU] key.

The recorded content is played back via the

[LINE OUTPUT] jack and [PHONES] jack.

TRACK [1] key

TRACK [2] key

TRACK [3] key

TRACK [4] key

WAV (96 kHz)

WAV (48 kHz)

WAV (44.1 kHz)

MP3 (44.1 kHz)

Input level

Setting Application

L

For on-mic recording of instruments or

single-session recording of a band

performance.

M

For recording of acoustic guitar and

other instruments with low volume.

H

Off-mic recording setting, mostly for use

in the ﬁeld.

H4_E.book 13 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

14

Quick Guide 1

Stereo mode basic operation

This section explains the basics of using the unit in stereo mode. As an example, it shows how to record a

band performance in one go with the built-in stereo mic.

Preparations before

recording

Starting the H4

1.

Connect the monitor system to the

H4, and turn power on in the order

H4

→

monitor system.

2.

Verify that the [MODE] indicator is lit.

If the [MODE] indicator is out, the H4 is in 4-

track mode. Switch it to stereo mode (

→

p. 30).

The display shows the stereo mode top screen.

If another screen is shown, press the center of the

[MENU] key repeatedly to bring up the screen

shown above.

Adjusting the input sensitivity/

recording level

To record the input signal with optimum quality,

the input sensitivity and recording level must be

adjusted correctly.

◆

Input sensitivity adjustment

The input sensitivity adjustment controls the

input level to the analog section, to ensure that

the signal from the built-in stereo mic or the

[INPUT 1]/[INPUT 2] jacks can be handled by

the H4 at an appropriate level.

1.

Use the [MIC GAIN] switch on the

right side panel to adjust the input

sensitivity (

→

page 13).

◆

Recording level adjustment

The recording level adjustment controls the gain

of the signal to be recorded by the recorder, in

other words it sets the input level to the digital

section of the H4. The method described in this

section uses the auto gain function to detect the

level and make the adjustment automatically.

2.

At the stereo mode top screen, press

the bottom of the [MENU] key.

The [MENU] key serves for calling up various

menus of the H4, and it also functions as the

recorder transport key pad. It works differently

depending on whether the top, bottom, left, right,

or center portion of the key is pressed (see

illustration on next page).

When you press the bottom (INPUT MENU) of

Lit

Stereo mode

H4_E.book 14 ページ２００６年９月１日　金曜日　午後７時５６分

Quick Guide 1

Stereo mode basic operation

ZOOM H4

15

[MENU] key functions in stereo mode

Press top (@) of [MENU] key

Start/stop recorder playback.

Hold down right part (I) of [MENU]

key

Fast-forward from current point in

1-second increments.

Press right part (I) of [MENU] key

Select next file.

Hold down left part (U) of [MENU]

key

Fast-reverse from current point in

1-second increments.

Press left part (U) of [MENU] key

Return counter to zero. If counter is at

zero, select previous file.

Press center of [MENU] key

Display main menu for various settings

(or return to immediately preceding screen).

Press bottom (INPUT MENU) of [MENU] key

Display INPUT menu for making various input

related settings.

the [MENU] key at the top screen of the stereo

mode, the following INPUT menu appears.

This screen lets you select the input source and

fine-adjust the input level. The “ ” symbol on

the screen is called the cursor. It indicates which

item is currently selected for an operation.

3.

Move the jog dial up/down to bring

the cursor to the “AUTO GAIN” item,

then press the jog dial inwards.

The jog dial on the right side panel allows the

following two actions.

●

Move up/down

Pushing the jog dial up or

down serves to move the

cursor on the screen and to

change setting values.

●

Press

Pushing the jog dial

inwards accepts a selected

item or a changed setting.

When you move the jog dial up/down at the

above screen and bring the cursor to “AUTO

GAIN”, the AUTO GAIN function is selected as

setting item. In this condition, pressing the jog

dial enables switching the auto gain function

between on and off.

4.

Move the jog dial up/down to display

“ON”. Then press the jog dial.

The auto gain function is now on.

HINT

• It is also possible to set the recording level

manually (

→

p. 31).

• The auto gain function adjusts the input level to

the digital section. If using the function does

not result in a suitable input level, you should

adjust the input sensitivity (analog level)

(

→

p. 13).

5.

Press the center of the [MENU] key

to return to the stereo mode top

screen.

Cursor

Press

Move

up/down

H4_E.book 15 ページ２００６年９月１日　金曜日　午後７時５６分

Quick Guide 1

Stereo mode basic operation

ZOOM H4

16

6.

At the stereo mode top screen, press

the [REC] key.

The [REC] key flashes, and the recorder is now

in the standby condition.

When the auto gain function is enabled, the

indication “REC LEVEL SCANNING...” will be

shown when you switch the recorder to standby.

7.

Point the mic(s) at the performers

and have them play at the loudest

level.

The H4 detects the level of the currently selected

input source and adjusts the recording level

accordingly. If the band you are recording does

not play louder than during this test, the entire

recording should be possible without distortion.

8.

To cancel the recording standby

condition, press the left part (U

),

right part (I

), or top (@

) of the

[MENU] key.

Using effects

In stereo mode, you can use various effects of the

H4. The compressor/limiter module is useful to

prevent distortion due to sudden volume peaks

and to keep even low sounds at a suitable level.

The sound character of the built-in stereo mic

can be altered using a number of mic simulation

effects. This section describes how to use the

effect section to adjust the input signal level and

change the characteristics of the built-in stereo

mic.

HINT

The mic simulation effects are available only when

using the built-in stereo mic.

1.

At the stereo mode top screen, press

the bottom of the [MENU] key.

The INPUT menu for making various input

related settings appears.

2.

Bring the cursor to the “COMP/

LIMIT” item and press the jog dial.

The COMP/LIMIT (compressor/limiter) module

settings can now be made.

3.

Move the jog dial up/down to select

one of the following settings.

• OFF (default)

The COMP/LIMIT module is off.

• COMP

The compressor which attenuates high-level

signals and boosts low-level signals is active.

• LIMIT

The limiter which attenuates high-level

signals that exceed a certain threshold is

active.

Automatically set

recording level

Currently selected

input source

H4_E.book 16 ページ２００６年９月１日　金曜日　午後７時５６分

Quick Guide 1

Stereo mode basic operation

ZOOM H4

17

HINT

To check the action of the effect, press the [REC]

key to set the H4 to the recording standby

condition, and then monitor the signal at the [LINE

OUTPUT] or [PHONES] jack while the instruments

to record are being played.

4.

To accept the settings for the COMP/

LIMIT module, press the jog dial.

5.

Bring the cursor to the “MIC MODEL”

item and press the jog dial.

If the built-in stereo mic is selected as input

source, the MIC MODEL module is available in

addition to the COMP/LIMIT module. This

module simulates the characteristics of various

well-known microphone models.

6.

Move the jog dial up/down to change

the MIC MODEL module settings.

The following microphone simulation settings

are available.

• OFF (default)

The MIC MODEL module is off.

• SM57, MD421, U87, C414

The MIC MODEL module is enabled, and the

respective mic characteristics are simulated.

For details on mic characteristics, see page

95.

7.

To accept the settings for the MIC

MODEL module, press the jog dial.

8.

To return to the stereo mode top

screen, press the center of the

[MENU] key.

HINT

• In stereo mode, you only need to select an

effect type. There is no provision for adjusting

detailed parameters.

• For details about the effects available in stereo

mode, see the reference section at the end of

this manual.

• If you have switched effects on or off or

changed effect settings, the recording level will

have to be readjusted.

• Manufacturer names and product names

mentioned in this documentation are

trademarks or registered trademarks of their

respective owners. The names are used only to

illustrate sonic characteristics and do not

indicate any afﬁliation with ZOOM

CORPORATION.

Recording

To record in stereo mode, proceed as follows.

1.

At the stereo mode top screen, use

the TRACK [1] – [4] keys to select the

recording format (

→

p. 13).

2.

Press the [REC] key.

The [REC] key flashes, and the recorder is now

in the standby condition.

The level meter on the display lets you check the

input signal level (recording level). You can also

monitor the input signal via the [LINE

OUTPUT] jack/[PHONES] jack.

HINT

• If the monitor function (

→

p. 36) is on, the signal

can always be monitored via the [LINE

OUTPUT] jack/[PHONES] jack, even if the unit

is not in recording standby mode.

• If the auto gain function is on, the input signal

level will be detected when you set the H4 to

H4_E.book 17 ページ２００６年９月１日　金曜日　午後７時５６分

Quick Guide 1

Stereo mode basic operation

ZOOM H4

18

the recording standby condition.

3.

To start recording, press the [REC]

key once more.

If required, you can use the metronome function

while recording (

→

p. 77).

4.

To stop recording, press the [REC]

key, or press the top (@

) of the

[MENU] key.

The counter returns to zero. If you press the top

(@

) of the [MENU] key in this condition, the

recording is played back from the beginning.

If you press the [REC] key again, the recorder

goes again into the standby condition, and you

can record a new stereo file.

NOTE

In stereo mode, a new stereo file is created every

time from the beginning. It is not possible to

record onto an existing file or start recording from

a specified position. (For information on how to

delete unneeded stereo files, see page 73.)

Selecting a file for playback

In stereo mode, one stereo file (WAV or MP3

format) is created for each recording operation.

These files are stored on the SD card in the

dedicated “STEREO” folder.

To select a file from this folder for playback,

proceed as follows.

1.

Verify that the display shows the

stereo mode top screen.

HINT

• Files recorded in stereo mode have the name

“STE-xxx.wav (mp3)” which is assigned

automatically (where xxx is a number from 000

to 999).

•You can change the ﬁle name (

→

p. 72).

2.

Move the jog dial up/down to bring

the cursor to the file name. Then

press the jog dial.

File selection is now possible.

3.

Move the jog dial up/down to select a

file.

All files recorded in stereo mode are shown in

turn.

4.

To accept the file selection, press the

jog dial.

5.

To play the selected file, press the

top (@

) of the [MENU] key.

The file selected in step 3 is played back.

6.

To stop playback, press the top (@

)

of the [MENU] key once more.

Name of currently selected file

H4_E.book 18 ページ２００６年９月１日　金曜日　午後７時５６分

ZOOM H4

19

Quick Guide 2

4-track mode basic operation

In 4-track mode, the H4 operates as a multi-track recorder with four tracks. This section explains the

basics of using the unit in 4-track mode. As an example, it shows how to record instruments or vocal parts

one track at a time, and perform a final mix.

In this section, the recording mode is “Overwrite” (every recording operation overwrites the current file).

Note that operation steps differ depending on the recording mode. For details, see page 41.

The description in this section covers the following four steps.

●

Step 1: Preparations

This includes selecting the mode, creating a project, and other preparation for recording.

●

Step 2: Recording the first track

Record the first track using the input signal after effect processing.

●

Step 3: Add more tracks

While listening to the recorded track, record the second and subsequent tracks.

●

Step 4: Mixing and bounce

Create a stereo mix while adjusting the level and panning settings for the four recorded

tracks. Then write the final stereo mix to a file (bounce).

Step 1: Preparations

Switch to 4-track mode

In the default condition, the H4 operates in stereo

mode (the [MODE] indicator on the top panel is

lit). To switch the H4 to 4-track mode, proceed

as follows.

1.

At the stereo mode top screen, press

the center of the [MENU] key.

The main menu for making various settings

appears.

2.

Move the jog dial up/down to bring

the cursor to “MODE”. Then press

the jog dial.

The MODE SELECT screen appears.

3.

Move the jog dial up/down to bring

the cursor to “4TRACK RECORDER”.

4.

Press the jog dial.

The H4 switches to 4-track mode and the

[MODE] indicator goes out. The display

automatically changes to the 4-track mode top

screen.

H4_E.book 19 ページ２００６年９月１日　金曜日　午後７時５６分

Quick Guide 2

4-track mode basic operation

ZOOM H4

20

HINT

To return from 4-track mode to stereo mode,

perform the same steps from the 4-track mode

top screen, select “STEREO RECORDER”, and

press the jog dial.

Creating a new project

In 4-track mode, the H4 manages recordings in

units called “projects”. When you start a new

recording, create a project as follows.

1.

At the 4-track mode top screen,

press the center of the [MENU] key.

The main menu for making various settings

appears.

2.

Move the jog dial up/down to bring

the cursor to “PROJECT”. Then

press the jog dial.

The PROJECT menu for project related

operations appears.

HINT

When you call up the PROJECT menu, the current

project is saved automatically.

3.

Move the jog dial up/down to bring

the cursor to “NEW PROJECT”. Then

press the jog dial.

The default name for the new project is shown.

HINT

You can change the name of the project at this

point (

→

p. 55), or you can change it later

(

→

p. 56).

4.

To create the new project, move the

jog dial up/down to bring the cursor

to the OK button, and then press the

jog dial.

The newly created project is automatically

loaded, and the 4-track mode top screen appears.

If you select the CANCEL button instead of the

OK button, the new project is not created, and

the PROJECT menu appears again.

Making metronome settings

The H4 incorporates a metronome function that

is useful for practice or for multi-track recording.

Listening to the metronome during recording can

help keep correct timing when adding

instrumental or vocal tracks. (The sound of the

metronome is not recorded on the track.)

This section explains how to set the metronome

tempo and volume.

1.

At the 4-track mode top screen,

press the center of the [MENU] key.

The main menu for making various settings

appears.

2.

Move the jog dial up/down to bring

Name for

project to be

created

H4_E.book 20 ページ２００６年９月１日　金曜日　午後７時５６分

Page is loading ...

Zoom Handy Recorder H4 Datasheet

This manual is also suitable for

Zoom Handy Recorder H4 Datasheet

Related papers

Other documents