P-963ESP
AM/FM/MPX RADIO
WITH
FOLD-DOWN DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER, CD CHANGER CONTROLS,
MP3 CD PLAYBACK, REMOTE CONTROL
AND QUARTZ CLOCK
INSTALLATION MANUAL
Released: 2-17-04
Rev A: Revised Power Pins 4 and 7 functions page 6 : 4-6-04.
CAR CD-R/RWMP3 PLAYBACK
5
CD- CD+
6
P-963ESP
RPT
34
SHFPAU
1
SCN
2
MP3
ENTER
MONO
JAZZ
LOC
REG
LOUD
ST
CLAS
POP
TP
ME/CR
AF TA
PTY
EON
Sub. W
-2-
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation
kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo
specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a
kit but cannot find it available, call our toll-free “HELP” line at 1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the fold-down detachable front panel if it is attached to the chassis by pushing the fold-down button; then press the
“Release” button and slide the panel off the front mounting plate. Now slide the mounting sleeve off of the chassis. If it is locked
into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or
file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend
or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the
dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the
wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or
electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn
the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, re-check all wiring until problem is
corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock
it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided.
Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw
and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the
radio or improper operation due to vibration.
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit
to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 of the installation procedure.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some
Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local
car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will
be used to mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION : DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
4. Wire the new radio to the vehicle as per step 4 of the Universal Installation Procedure.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
-3-
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
SCREW STUD
PERFORATED STRAP
SCREW
FASTEN THIS END TO
SCREW STUD ON
REAR OF CHASSIS
BEND TOP TABS
UPWARD
MOUNTING SLEEVE
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
NOTE: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NUT
BEND BOTTOM TABS
DOWNWARD
RADIO
FASTEN THIS END TO SECURE PART
OF DASHBOARD.
DRILL HOLE IF NECESSARY.
TYPICAL INSTALLATION
MAX. SIZE
M5 x 8
FACTORY MOUNTING BRACKETS
ISO INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE
FRONT OF THE CHASSIS BY CAREFULLY
UNSNAPPING IT.
UNSNAP AT 2 PLACES
EACH ON TOP AND
BOTTOM
PLASTIC FRAME
DETACHABLE
FRONT PANEL
REMOVAL
TOOLS
8:30AM - 7PM
9AM - 5PM
CENTRAL
EASTERN
6:30AM - 5PM
7AM - 3PM
MOUNTAIN
5:30AM - 4PM
6AM - 2PM
PACIFIC
MON.-FRI.
SATURDAY
DAY
TIME ZONE
TT
TT
T
oll-Froll-Fr
oll-Froll-Fr
oll-Fr
ee
ee
e
e Inse Ins
e Inse Ins
e Ins
tt
tt
t
allatallat
allatallat
allat
ion Asion As
ion Asion As
ion As
sissis
sissis
sis
tt
tt
t
ancanc
ancanc
anc
ee
ee
e
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're
here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown
(U.S.A. and Canada only).
7:30AM - 6PM
8AM - 4PM
-4-
RR
RR
R
AA
AA
A
DIO WIRINGDIO WIRING
DIO WIRINGDIO WIRING
DIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
RADIO
8-PIN CONNECTORS
ANTENNA
CONNECTOR
ANTENNA
PLUG
CAR
BATTERY
VEHICLE
FUSEBLOCK
“RADIO” OR
“ACCESSORY”
FUSE
RED
BLACK
YELLOW
IMPORTANT
THIS WIRE MUST BE CONNECTED
TO A CONSTANT 12-VOLT SOURCE
OR RADIO WILL NOT OPERATE
PROPERLY
TO SPEAKERS (SEE SPEAKER
WIRING DIAGRAM)
SPEAKERS
POWER
ANTENNA
CD CHANGER
CONNECTOR
10-AMP
FUSE
AUTOMATIC
ANTENNA
ANTENNA
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED
TO REMOTELY ACTIVATE AN
AUTOMATIC ANTENNA OR AN
EXTERNAL AMPLIFIER (SEE
ANTENNA OR AMPLIFIER
MANUAL)
SCREW
METAL PART OF DASH
(DRILL HOLE IF
NECESSARY)
POSITIVE (+) TERMINAL
12-VOLT BATTERY
-5-
SPESPE
SPESPE
SPE
AA
AA
A
KK
KK
K
ER WIRINGER WIRING
ER WIRINGER WIRING
ER WIRING
REFER TO PAGE 4
FOR RADIO WIRING
l
l
l
l
WARNING!
THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO.
WHITE w/BLACK STRIPE
GRAY w/BLACK STRIPE
8-PIN PLUG
WHITE
LEFT FRONT SPEAKER
RIGHT FRONT SPEAKER
LEFT REAR SPEAKER
RIGHT REAR SPEAKER
GREEN
8-PIN PLUG
GREEN w/BLACK STRIPE
VIOLET w/BLACK STRIPE
RADIO
HELP!
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
Monday - Friday
Saturday
1-800-645-4994
8-PIN DIN SOCKET FOR CONNECTION TO
CD CHANGER ADAPTER CABLE
DIN CABLE (SUPPLIED
WITH CD CHANGER).
6
COMPACT
OPTIONAL CD CHANGER
SEE PAGE 4
FOR RADIO WIRING
NOTE:
CALL 1-800-645-4994 FOR RECOMMENDATIONS
OF MODEL CHANGERS THAT WILL WORK WITH
YOUR RADIO.
GRAY
VIOLET
ISO 8-PIN SOCKET TO 8-PIN DIN
SOCKET CD CHANGER ADAPTER CABLE,
PART NUMBER P956CDC (SUPPLIED) SEE
PAGE 6 FOR DETAILS
ISO 6-PIN SOCKET TO
RCA LOW LEVEL
OUTPUTADAPTER
CABLE, PART
NUMBER P956RCA
(SUPPLIED) SEE
PAGE 6 FOR DETAILS
ISO 8-PIN SOCKET TO
RCA LOW LEVEL AUX
INPUT ADAPTER
CABLE, PART
NUMBER P956AUX
(SUPPLIED) SEE
PAGE 6 FOR DETAILS
8-PIN
CONNECTORS
-6-
ISO AISO A
ISO AISO A
ISO A
DADA
DADA
DA
PTER CABLE CONNECPTER CABLE CONNEC
PTER CABLE CONNECPTER CABLE CONNEC
PTER CABLE CONNEC
TT
TT
T
IONSIONS
IONSIONS
IONS
REFER TO PAGE 5 FOR OPTIONAL CD CHANGER AND AUDIO LEVEL OUTPUT CONNECTIONS
ISO 6-PIN SOCKET TO RCA LOW LEVEL OUTPUT
ADAPTER CABLE, PART NUMBER P956RCA
ISO 8-PIN SOCKET TO RCA LOW LEVEL
AUX INPUT ADAPTER CABLE, PART
NUMBER P956AUX
ISO 8-PIN SOCKET TO 8-PIN DIN SOCKET
CD CHANGER ADAPTER CABLE, PART
NUMBER P956CDC
Main power supply (+B ignition)
Memory (+B permanent)
BATTERY PLUS
Front R ch RED
Front L ch WHITE
Rear R ch RED
Rear L ch WHITE
ISO SOCKET PINOUTS
Part A: Power Connection Part B: Speaker Connection
1 Free 1+
2 Free 2-
3 Free 3+
4 Main power supply (+B Ignition) 4-
5 Trip line for fully automatic antenna 5+
6 Free 6-
7 Memory (+B Permanent) 7+
8 Ground 8-
Part C: Special Functions
1 Audio frequency out, rear left 11 Not allocated
2 Audio frequency out, rear right 12 subwoofer GND
3 Audio frequency out, ground 13 CD bus
4 Audio frequency out, front left 14 CD bus
5 Audio frequency out, front right 15 Ground
6 Battery plus, switched by radio 16 Battery plus, unswitched
7 Aux in R ch 17 Battery plus, unswitched
8 Aux in L ch 18 CD ground
9 Aux in GND 19 CD line in, left channel
10 Subwoofer out 20 CD line in, right channel
RR=Rear right
FR=Front right
FL=Front left
RL=Rear left
R CH (RED)
L CH (WHITE)
GREEN
AUX IN CABLE
(FOR AUX IN VERSION ONLY)
(FOR SUBWOOFER VERSION ONLY)
SUBWOOFER CABLE
(FOR CDC VERSION ONLY)
CDC SOCKET
PART C
PART B
PART A
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
4
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
15A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
3
5
7
2468
1
2
3
4
5
6
7
8
PART A
PART B
PART C
-6-
THIS PAGE LEFT BLANK INTENTIONALLY
-6-
© 2004 AUDIOVOX ELECTRONICS CORP., HAUPPAUGE, NY Printed in China
128-6982A
/