Kingston Technology KVR13E9K3/6I Datasheet

Category
Memory modules
Type
Datasheet

Kingston Technology KVR13E9K3/6I is a 6GB (2GB x 3) DDR3-1333 ECC DIMM kit designed for use in servers and workstations. It features a CL9 latency and is compatible with Intel platforms. The kit includes three 240-pin DIMMs, each with nine 256M x 8-bit FBGA components. The DIMMs use gold contact fingers and are rated for a maximum operating power of 2.430W. They operate at a voltage of 1.5V and have an operating temperature range of 0°C to 85°C. The DIMMs are also RoHS compliant and UL rated 94 V - 0.

Kingston Technology KVR13E9K3/6I is a 6GB (2GB x 3) DDR3-1333 ECC DIMM kit designed for use in servers and workstations. It features a CL9 latency and is compatible with Intel platforms. The kit includes three 240-pin DIMMs, each with nine 256M x 8-bit FBGA components. The DIMMs use gold contact fingers and are rated for a maximum operating power of 2.430W. They operate at a voltage of 1.5V and have an operating temperature range of 0°C to 85°C. The DIMMs are also RoHS compliant and UL rated 94 V - 0.

KVR13E9K3/6I
6GB (2GB 1Rx8 256M x 72-Bit x 3 pcs.)
PC3-10600 CL9 240-Pin ECC DIMM Kit
DESCRIPTION
ValueRAM's KVR13E9K3/6I is a kit of three 256M x 72-bit
(2GB) DDR3-1333 CL9 SDRAM (Synchronous DRAM), 1Rx8,
ECC, Intel
®
Compatibility Tested, memory modules, based on
nine 256M x 8-bit FBGA components per module. Total kit
capacity is 6GB. The SPDs are programmed to JEDEC stan-
dard latency DDR3-1333 timing of 9-9-9 at 1.5V. Each 240-pin
DIMM uses gold contact fingers. The electrical and mechanical
specifications are as follows:
FEATURES
JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
667MHz fCK for 1333Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Thermal Sensor Grade B
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
PCB: Height 1.18” (30mm), single sided component
Document No. VALUERAM1210-001.A00 05/11/12 Page 1
Memory Module Specifi cations
SPECIFICATIONS
CL(IDD) 9 cycles
Row Cycle Time (tRCmin) 49.5ns (min.)
Refresh to Active/Refresh 160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 36ns (min.)
Maximum Operating Power 2.430 W* (per module)
UL Rating 94 V - 0
Operating Temperature 0
o
C to 85
o
C
Storage Temperature -55
o
C to +100
o
C
*Power will vary depending on the SDRAM used.
Continued >>
MODULE DIMENSIONS:
Document No. VALUERAM1210-001.A00 Page 2
Units: millimeters
30.00
18.80
15.80
11.00
8.00
0.00
133.35
0.00
54.70
TECHNOLOGY
  • Page 1 1
  • Page 2 2

Kingston Technology KVR13E9K3/6I Datasheet

Category
Memory modules
Type
Datasheet

Kingston Technology KVR13E9K3/6I is a 6GB (2GB x 3) DDR3-1333 ECC DIMM kit designed for use in servers and workstations. It features a CL9 latency and is compatible with Intel platforms. The kit includes three 240-pin DIMMs, each with nine 256M x 8-bit FBGA components. The DIMMs use gold contact fingers and are rated for a maximum operating power of 2.430W. They operate at a voltage of 1.5V and have an operating temperature range of 0°C to 85°C. The DIMMs are also RoHS compliant and UL rated 94 V - 0.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI