ANZZI SD-AZ050-01CH User manual

ANZZI
Brand
ANZZI
Model
SD-AZ050-01CH
Type
User manual

This manual is also suitable for

ANZZI SD-AZ050-01CH is a heavy product that requires two people to install. It features glass corner protectors that remain on during installation, glass protective seals that are mounted to the door before opening or closing, and glass panels that are aligned and level with the wall and floor. The slider must be installed correctly for smooth sliding. To care for the product, wipe the bases and back walls with a soft cloth after each use and clean the acrylic surface with non-abrasive sprays or cream-based cleaners.

ANZZI SD-AZ050-01CH is a heavy product that requires two people to install. It features glass corner protectors that remain on during installation, glass protective seals that are mounted to the door before opening or closing, and glass panels that are aligned and level with the wall and floor. The slider must be installed correctly for smooth sliding. To care for the product, wipe the bases and back walls with a soft cloth after each use and clean the acrylic surface with non-abrasive sprays or cream-based cleaners.

V1.4
10/30/2022
ITEM: SD-AZ050-01**
10/30/2022
V1.4
This product is heavy and requires two people
to install.
1.
Glasscorner protectorsremainonduring
installation.
2.
Glassprotectivesealsaremountedtothe
doorbeforeopening/closing.
3.
Glasspanels are aligned & level with wall/floor.
4.
Slider must be installed correctly for smooth
sliding.
5.
2
This product is heavy
and requires two
people to install.
3
This product is heavy and requires two people to install.
4
5
6
7
Corner
Protector
Carefully remove the Corner Protectors from the Fixed Panel [05]. Connect and secure the
Horizontal Rails [02] and Fixed Panels [05] with eight Screws ST4X35 [11]. Make sure the
flange of upper Horizontal Rails [02] pointed downwards, the flange of lower Horizontal Rails
[02] pointed upwards. (Fig 1.3 & Fig 1.4)
8
9
10
11
12
Corner
Protector
Carefully remove the Corner Protectors. Snap the Magnetic seals [03] to the side of
Door Panel [06] close to the center. (Fig 7.2 & Fig 7.3)
13
14
15
16
BASES and BACK WALLS: Wipe them off after each use with a soft cloth. To clean the
acrylic surface, use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol
spray cleaners. Never use abrasive cleansers, metal brushes, or scrapers, as they can
scratch or dull the surface.
GLASS: Wipe off the glass after each use with a soft cloth or a squeegee to prevent soap
buildup and water spots (hard water can etch the surface of the glass over time if left to
dry). To avoid damaging the surface, never use abrasive cleaners or cleaning products that
contain scouring agents. Likewise, never use bristle brushes or abrasive sponges that can
scratch the surface.
HARDWARE: To ensure a long-lasting finish, wipe off the metal parts after using with a
soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach,
or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the
finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe
dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying
stainless steel cleaner or polish to stainless steel hardware, work with (not across) the
grain. Never use an abrasive sponge or cloth, steel wool, or wire brush, which may
permanently scratch the surfaces.
NOTE: Regularly inspect the glass and all hardware for misalignment, proper
attachment, and damage. Contact ANZZI with any questions or concerns.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

ANZZI SD-AZ050-01CH User manual

ANZZI
Brand
ANZZI
Model
SD-AZ050-01CH
Type
User manual
This manual is also suitable for

ANZZI SD-AZ050-01CH is a heavy product that requires two people to install. It features glass corner protectors that remain on during installation, glass protective seals that are mounted to the door before opening or closing, and glass panels that are aligned and level with the wall and floor. The slider must be installed correctly for smooth sliding. To care for the product, wipe the bases and back walls with a soft cloth after each use and clean the acrylic surface with non-abrasive sprays or cream-based cleaners.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents