Xenios 2TouchPOS provides a convenient and efficient way to manage your business. With its ability to be wall-mounted, you can save space and keep your workspace organized. The 2TouchPOS is also equipped with a hard drive, allowing you to store and access important data and applications. Additionally, the 2TouchPOS is compatible with Posiflex touch screens, giving you the flexibility to choose the right display for your needs.
2013 Xenios LLC
82 Saint Paul Street
Rochester, NY 14604
Phone 585.325.5242 • Fax 585.325.6989
2TouchPOS Wall Mount
User’s Guide
Xenios LLC @2013 Page 2
Contents
About this Document ...................................................................................................................... 3
Removing the Hard Drive ........................................................................................................... 4
Placing Hard Drive Directly into Posiflex Screen ...................................................................... 8
Attaching Posiflex Touch Screen to Wall Mount ..................................................................... 12
Xenios LLC @2013 Page 3
About this Document
This document was written for 2TouchPOS version 3.03.4900.
Xenios LLC @2013 Page 4
Removing the Hard Drive
1. First, you will turn off the power to your Posiflex terminal. Tilted the Posiflex terminal
back and unplug power cable.
Xenios LLC @2013 Page 5
2. In the front part of your Posiflex terminal, there is a plastic plate; you will remove plastic
plate to expose the hard drive. Press down on the clip release and remove plastic plate.
3. Using a Phillips head screwdriver, unscrew the single screw.
Xenios LLC @2013 Page 6
4. Pull down on the metal bar and slide hard drive tray out.
Xenios LLC @2013 Page 7
5. Unscrew all four screws and remove hard drive.
Xenios LLC @2013 Page 8
Placing Hard Drive Directly into Posiflex Screen
1. Remove Base Terminal stand by pressing plastic clip, located on the backside of your
terminal. Hold the clip, place other hand on the terminals front side of your Posiflex
touch screen and lift screen up.
Xenios LLC @2013 Page 9
2. Place your Posiflex touch screen on a flat clean surface. Disconnect hard drive power and
sata cables.
3. Top right hand corner of the terminal, there are two screws you will remove, then take
plastic plate off. The hard drive will be placed into here.
Xenios LLC @2013 Page 10
4. Once plastic plate is removed, you will see two cables, hard drive power and sata cable.
Xenios LLC @2013 Page 11
5. Connect hard drive with hard drive power and sata cables.
6. Once cables are attached, slide hard into drop down area. Reattached plastic plate with
the two screws.
Xenios LLC @2013 Page 12
Attaching Posiflex Touch Screen to Wall Mount
1. In the Wall Mount hardware package, there are wall mounting instructions and
measurements that will help you mount your Posiflex screen onto the wall.
2. The diagram instruction sheet is used to drill holes into the wall matching bracket screw
holes.
3. Take the wall mounting diagram sheet and place it against the wall. Take a pair of
scissors and cut wholes in diagram sheet, then mark wall with a pencil, where you will
drill holes. Using a drill, drill holes and place anchors into wall. Screw in screws into
anchors. Match up wall mounting bracket to screws in the wall. Make sure your mall
mount is secure before hanging your Posiflex touch screen.
Xenios LLC @2013 Page 13
4. The four metal braces are located on the back of Posiflex terminal. Place the metal
bracket on the wall and secure it. Match the four terminal braces with wall mount (flat
side). Slide Posiflex Touch screen onto to wall mount. Again, make sure everything is
secure before letting go of touch screen.
Xenios LLC @2013 Page 14
5. Once Posiflex screen is mounted on wall, re-connect power, and sata cables.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Posiflex KS-7212/X User manual
Posiflex TX-4200 \ TX-4200E (EN) User manual
POSIFLEX Business Machines KS-6215 User manual
Posiflex KS-6915/ KS-6917/ KS-7215/KS-7217 User manual
Posiflex XT-4015 User manual
