PAR EverServ ES500 Setup Manual

Brand: PAR

Model: EverServ ES500

Type: Setup Manual

PAR ES500® POS Terminal Setup Guide

Thank You!

Thank you for purchasing a PAR point-of-

sale system. We are confident that our

technology solutions will contribute to your

business success.

Examine the Shipment:

 Use the invoice to ensure all equipment is

present.

 Report any missing or damaged

equipment to your PAR salesperson.

Inventory Components:

Ensure you have the following items in your

POS order:

 POS terminal

 AC power cord

 2 Serial adapter cables (C8200)

 Dual Cash Drawer Adapter cable (C2355)

1. Power LED 2. Touch Screen and LCD

3. Power Switch 4. Customer Display

5. Credit Card Reader 6. Cable Well

POS Dimensions

ES500 POS Terminal Overview

Remove Terminal from

Box

Remove the terminal from the box as

shown.

C2355 Dual Cash Drawer Adapter Cable (Right) TwoC8200 Adapter Cables (Left)

Note: The ES500 POS terminals have two non-powered RJ-

50 10-pin (COM 1 & 2) serial connections. COM 3 and COM

4 are powered RJ-50 serial ports. COM 3 is 5V and COM 4

is 12V. The ES500 has no DB9 serial ports - only RJ-50

10P10C-pin serial ports. When using peripherals with DB9

serial connections with the ES500, an adapter cable must

be used. An example would be between the terminal and

the printer serial interface cable. The adapter cable (PN

C8200) comes in approximately 10” length. A C2355 (Dual

Cash Drawer Adapter Cable) cable is shipped with each

terminal and additional cables can be purchased from PAR.

Inventory Equipment

Power Cord

ES500 Register

PAR ES500® POS Terminal Setup Guide

Service and Support

For service and support during or after installation,

contact the PAR phone center at 1-800-382-6200.

Battery Warning

A lithium coin-type battery is installed on the ES500

motherboard. If this battery is replaced, it must be replaced

with an equivalent battery type. Dispose of the used battery

according to local disposal instructions.

Connect AC Power Cord to

Terminal

1. Lay the terminal on its back on a clean, flat

surface.

2. Locate the AC power cord.

3. Connect the AC power cord to the POS

terminal power supply. The power supply is on

the underside of the terminal.

4. Connect the other end of the AC power cord

to an uninterruptible power supply (UPS)

Connect Peripherals to POS Terminal

1. Lay the terminal on the counter on its back

with the bottom facing you.

2. Tilt the top cover up.

3. Connect your peripherals to the POS terminal.

Refer to the Cable Connections diagram.

4. Place register upright.

5. Power on the POS terminal. The power button

is located on the bottom left side of the top

cover.

6. Power on the peripherals.

Plug Power Cord into

Power Brick

Cable Connections

CD1= RJ-12 Cash

Drawer Port

LAN Connection

USB Ports

COM 1 COM2

(Connect C8200

Cable)

VGA

Power

Button

Input/Output Connections

M5100:

 Two RJ-50 10-pin Serial Ports (COM 1 & 2)

 Two RJ-50 Serial Ports available with +12 or 5V

(COM 3 & 4)

 One RJ-12 Cash Drawer port

 Four (4) Standard 2.0 USB ports

 One 10/100/1000 Ethernet Network port

 One VGA port for optional second play

 One +19V DC power input jack

(Connect C8200 Cable)

COM 3 (5V) COM 4 (12V)

DC Power

(from

Power

Supply)

Cable Well

Additonal Translations

Additional translations can be found at PAR’s website:

http://www2.partech.com/en/service-support/driver-

page.cfm

PAR EverServ ES500 Setup Manual

Brand: PAR

Model: EverServ ES500

Type: Setup Manual

Download PDF

report

PAR EverServ ES500 Setup Manual

PAR EverServ ES500 Setup Manual

Related papers

Other documents