DFI CMS330 Owner's manual

DFI
Brand
DFI
Model
CMS330
Category
Motherboards
Type
Owner's manual

This manual is also suitable for

CMS330-Q470E/H420E
microATX Industrial Motherboard
User’s Manual
ver.1_-_7-1321_23-15
2User's Manual | CMS330-Q470E/H420E
Copyright
This publication contains information that is protected by copyright. No part of it may be repro-
duced in any form or by any means or used to make any transformation/adaptation without the
prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions or
changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2022. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
• The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• Shielded interface cables must be used in order to comply with the emission limits.
3User's Manual | CMS330-Q470E/H420E
Table of Contents
Chapter 1 - Introduction................................................................................................................6
Specifications ......................................................................................................................... 6
Features .................................................................................................................................. 8
Block Diagram ........................................................................................................................9
Chapter 2 - Hardware Installation ..............................................................................................10
Board Layout.........................................................................................................................10
System Memory ...................................................................................................................11
Installing the DIMM Module .........................................................................................11
Removing the DIMM Module ........................................................................................12
CPU ........................................................................................................................................13
Installing the CPU Fan and Heat Sink .......................................................................... 13
Jumper Settings ...................................................................................................................14
CLEAR CMOS Data ........................................................................................................14
DIO Power ......................................................................................................................14
COM1/COM2 RS232/422/485 Select ..........................................................................15
COM1 RS232 Power Select ..........................................................................................16
AT/ATX Mode - JP26 .....................................................................................................17
USB Power Control - JP25 ............................................................................................ 18
Rear I/O Ports .......................................................................................................................19
USB Ports ....................................................................................................................... 20
Graphics Interfaces .......................................................................................................21
RJ45 LAN Ports ............................................................................................................. 22
Audio .............................................................................................................................22
COM 1 .............................................................................................................................23
Internal I/O Connectors .......................................................................................................24
SATA (Serial ATA) ..........................................................................................................24
Digital I/O Connector (2.0mm pitch)............................................................................24
COM (Serial) ports .........................................................................................................25
Cooling Fan Connectors ................................................................................................26
Power Connector ...........................................................................................................26
Front Panel .....................................................................................................................27
LAN LED Connector .......................................................................................................28
S/PDIF Connector .......................................................................................................... 28
SMBus Connector .........................................................................................................29
LPC Connector ............................................................................................................... 29
Chassis Intrusion Connector ........................................................................................30
InnoAGE HDR1 (JP24) ..................................................................................................30
Expansion Slots .............................................................................................................31
Installing the M.2 Module .............................................................................................31
Battery ............................................................................................................................32
Chapter 3 - BIOS Settings ...........................................................................................................33
Overview ...............................................................................................................................33
Main .......................................................................................................................................34
Advanced .............................................................................................................................34
RC ACPI Configuration ..................................................................................................35
CPU Configuration .........................................................................................................35
Power & Performance ...................................................................................................36
PCH-FW Configuration ..................................................................................................36
Trusted Computing ........................................................................................................39
NCT6126D Super IO Configuration ..............................................................................40
NCT5114D Super IO Configuration ..............................................................................42
Serial Port Console Redirection ...................................................................................43
USB Configuration .........................................................................................................44
CSM Configuration ........................................................................................................45
Network Stack Configuration........................................................................................46
USB Power Control ........................................................................................................46
Chipset ..................................................................................................................................47
Graphics Configuration .................................................................................................47
PEG Port Configuration ................................................................................................. 48
PCH-IO Configuration ....................................................................................................49
PCI Express Configuration ............................................................................................ 49
SATA And RST Configuration .......................................................................................50
HD Audio Configuration ................................................................................................50
Security .................................................................................................................................51
Secure Boot ....................................................................................................................51
Boot .......................................................................................................................................52
Save & Exit ............................................................................................................................52
Updating the BIOS ................................................................................................................ 53
Notice: BIOS SPI ROM..........................................................................................................53
Chapter 4 - RAID ..........................................................................................................................54
RAID Levels Explanation ...................................................................................................... 54
Setup Procedure ................................................................................................................... 54
4User's Manual | CMS330-Q470E/H420E
About this Manual
This manual can be downloaded from the website.
The manual is subject to change and update without notice, and may be based on editions that
do not resemble your actual products. Please visit our website or contact our sales representa-
tives for the latest editions.
Warranty
• Warranty does not cover damages or failures that occur from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
• The warranty is void if the product has been subjected to physical abuse, improper
installation, modification, accidents or unauthorized repair of the product.
• Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether
in or out of warranty. It must be returned to the purchase point, factory or authorized
service agency for all such work.
• We will not be liable for any indirect, special, incidental or consequential damages to
the product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
• To prevent electrostatic build-up, leave the system board in its anti-static bag until you
are ready to install it.
• Wear an antistatic wrist strap.
• Do all preparation work on a static-free surface.
• Hold the device only by its edges. Be careful not to touch any of the components, con-
tacts or connections.
• Avoid touching the pins or contacts on all modules and connectors. Hold modules or
connectors by their ends.
Safety Measures
• To avoid damage to the system, use the correct AC input voltage range.
• To reduce the risk of electric shock, unplug the power cord before removing the sys-
tem chassis cover for installation or servicing. After installation or servicing, cover the
system chassis before plugging the power cord.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other
components. Perform the upgrade instruction procedures described at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
5User's Manual | CMS330-Q470E/H420E
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 CMS330 motherboard
• 1 COM port cables (Length: 300mm, 2 x COM ports) A81-015026-023G
• 1 Serial ATA data cable (Length: 500mm) 332-553001-005G
• 1 I/O shield A49-CMS330-100G
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
When installing the system board in a new system, you will need at least the following internal
components.
• Memory module
• Storage device such as a hard disk drive.
• Power supply
External system peripherals may also be required for navigation and display, including at least
a keyboard, a mouse and a video display monitor.
www.dfi.com
PACKING LIST OPTIONAL ITEMS
ORDERING INFORMATION
Model Name P/N Description
CMS330-H420EC 770-CMS3301-000G 2 DDR4 UDIMM, 2 LAN, 1 RS-232/422/485, 6 USB 3.2 Gen1, 4 USB 2.0, Power: 24-pin ATX/8-pin ATX 12V, Active
thermal (with fan), -5 to 65°C
CMS330-Q470ECRM 770-CMS3301-100G 4 DDR4 UDIMM, 2 LAN, 1 RS-232/422/485, 2 USB 3.2 Gen2, 8 USB 3.2 Gen1, 6 USB 2.0, Power: 24-pin ATX/8-pin ATX
12V, Active thermal (with fan), -5 to 65°C
CMS330-H420EC 770-CMS3301-200G 2 DDR4 UDIMM, 2 LAN, w/ TPM 2.0, 1 RS-232/422/485, 6 USB 3.2 Gen1, 4 USB 2.0, Power: 24-pin ATX/8-pin ATX 12V,
Active thermal (with fan), -5 to 65°C
CMS330-Q470ECRM 770-CMS3301-300G 4 DDR4 UDIMM, 2 LAN, w/ TPM 2.0, 1 RS-232/422/485, 2 USB 3.2 Gen2, 8 USB 3.2 Gen1, 6 USB 2.0, Power: 24-pin
ATX/8-pin ATX 12V, Active thermal (with fan), -5 to 65°C
1 CMS330 motherboard
1 COM port cables (Length: 300mm, 2 x COM ports) A81-015026-023G
1 Serial ATA data cable (Length: 500mm) 332-553001-005G
1 I/O shield A49-CMS330-100G
USB 2.0 port cable (Length: 350/398mm) A81-001066-016G
USB 3.1 Gen1 port cable (Length: 320mm) A81-001052-023G
USB 3.2 Gen2 port cable (Length: 350mm) A81-001075-017G
COM port cable (Length: 300mm, 2 x COM ports) A81-015026-023G
Serial ATA data cable (Length: 500mm, W/LOCK) 332-553001-005G
Serial ATA data cable (Length: 500mm, W/LOCK, 90D) A81-002128-017G
Thermal solution (For 35W, Height: 37.3mm) A71-101107-000G
Thermal solution (For 65W, Height: 72.8mm) 552-200049-000G
Thermal solution (For 95W/125W, Height: 69.3mm) 761-103001-000G
DP to HDMI Dongle 612-D2H13M-000G
I/O shield (opt. for 4 x USB 2.0) A49-CMS330-000G
M.2-COM4 (M.2 serial port module) 770-M2COM1-000G
M.2-2LAN (M.2 LAN port module) 770-M22LN1-000G
M.2-2PSE (M.2 PSE module) 770-M22PS1-000G
OS SUPPORT Microsoft Windows 10 IoT Enterprise 64-bit
Linux Linux Ubuntu 20.04
ENVIRONMENT Temperature Operating: -5 to 65°C
Storage: -30 to 60°C with RTC Battery; -40 to 85°C without RTC Battery
Humidity Operating: 5 to 95% RH
Storage: 5 to 95% RH
MTBF Q470E: 504,615 hrs @ 25°C; 283,232 hrs @ 45°C ; 176,865 hrs @ 60°C ; 128,658 hrs @ 70°C
H420E: 534,071 hrs @ 25°C; 303,942 hrs @ 45°C ; 191,219 hrs @ 60°C ; 139,612 hrs @ 70°C
Calculation Model: Telcordia Issue 4
Environment: GB, GC - Ground Benign, Controlled
MECHANISM Dimensions micro ATX Form Factor
244mm (9.6") x 244mm (9.6")
Height PCB: 1.6mm
Top Side: 33mm; Bottom Side: 3mm
CERTIFICATIONS Certications CE, FCC Class B, UKCA
DFI reserves the right to change the specifications at any time prior to the product's release. Changes thereafter will be based on the product's revision. Please contact your
sales representative for the exact revision offered in your area. All product names mentioned are trademarks of their respective companies. © October 20, 2022 DFI Inc.
6
Chapter 1
INTRODUCTION
User's Manual | CMS330-Q470E/H420E
Chapter 1 - Introduction
XSpecifications
www.dfi.com
SPECIFICATION
SYSTEM Processor 10th Generation Intel® LGA 1200 Socket Processors, TDP support up to 125W
Intel® Core™ i9-10900E (10 Cores, 20M Cache, up to 4.7 GHz); 65W
Intel® Core™ i9-10900TE (10 Cores, 20M Cache, up to 4.5 GHz); 35W
Intel® Core™ i7-10700E (8 Cores, 16M Cache, up to 4.5 GHz); 65W
Intel® Core™ i7-10700TE (8 Cores, 16M Cache, up to 4.4 GHz); 35W
Intel® Core™ i5-10500E (6 Cores, 12M Cache, up to 4.2 GHz); 65W
Intel® Core™ i5-10500TE (6 Cores, 12M Cache, up to 3.7 GHz); 35W
Intel® Core™ i3-10100E (4 Cores, 6M Cache, 3.8 GHz); 65W
Intel® Core™ i3-10100TE (4 Cores, 6M Cache, to 3.6 GHz); 35W
Intel® Pentium® G6400E (2 Cores, 4M Cache, 3.8 GHz); 58W
Intel® Pentium® G6400TE (2 Cores, 4M Cache, 3.2 GHz); 35W
Intel® Celeron® G5900E (2 Cores, 2M Cache, 3.2 GHz); 58W
Intel® Celeron® G5900TE (2 Cores, 2M Cache, 3.0 GHz); 35W
Chipset Intel® Q470E/H420E Chipset
Memory Q470E: Four 288-pin Non-ECC UDIMM up to 128GB
H420E: Two 288-pin Non-ECC UDIMM up to 64GB
Dual Channel DDR4 2400/2666/2933MHz
BIOS AMI SPI 256Mbit
GRAPHICS Controller Intel® HD Gen 9 Graphics
Feature OpenGL 4.5, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display 1 x VGA VGA: resolution up to 1920x1200 @ 60Hz
1 x DP++ DP++: resolution up to 4096x2160 @ 60Hz
1 x HDMI 1.4b HDMI: resolution up to 4096x2160 @ 24Hz
Multiple Dis-
plays Q470E: VGA + DP++ + HDMI
H420E: VGA + DP++ / VGA + HDMI / DP++ + HDMI
EXPANSION Interface 1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
2 x PCI
Q470E:
1 x M.2 2242/2260/2280 M key (PCIe Gen3 x4 NVMe/SATA/Intel® Optane Memory and intel RST
support)
1 x M.2 2230 E key (USB 2.0/PCIe)
H420E: N/A
AUDIO Audio Codec Realtek ALC888
ETHERNET Controller 1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PHY with iAMT12.0 (10/100/1000Mbps)
(Q470E: Core i9/ i7/i5 supports iAMT, H420E: N/A)
REAR I/O Ethernet 2 x GbE (RJ-45)
Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)
USB 2 x USB 3.2 (Q470E: Gen2; H420E: Gen1)
2 x USB 3.2 Gen1 (Q470E: Up to 6 x USB 3.2 Gen1, MOQ required)
2 x USB 2.0
Display 1 x VGA
1 x DP++
1 x HDMI
PS/2 1 x PS/2 (mini-DIN-6)
Audio 1 x Line-out
1 x Mic-in
1 x Line-in (opt., MOQ required)
INTERNAL I/O Serial 9 x RS-232 (2.54mm pitch)
USB 2 x USB 3.2 Gen 1
Q470E: 4 x USB 2.0 (2.54mm pitch, Colay vertical Type A, opt.: MOQ required)
H420E: 2 x USB 2.0 (2.54mm pitch, Colay vertical Type A, opt.: MOQ required)
Audio 1 x Front Audio Header
1 x S/PDIF
SATA 4 x SATA 3.0 (up to 6Gb/s, SATA 3) (Q470E: RAID 0/1/5/10, H420E: N/A)
DIO 1 x 16-bit DIO
LPC 1 x LPC
SMBus 1 x SMBus
WATCHDOG
TIMER Output &
Interval System Reset, Programmable via Software from 1 to 255 Seconds
SECURITY TPM Infineon TPM2.0 (opt., MOQ required)
POWER Type ATX
Connector 8-pin ATX 12V power
24-pin ATX power
Consumption Typical: i9-10900K: 3.3V @ 0.36A (1.19W); 5V @ 1.02A (5.1W); 12V @ 3.8A (45.6W)
Max.: i9-10900K:3.3V @ 0.38A (1.25W); 5V @ 1.82A (9.1W); 12V @ 15.64A (187.68W)
RTC Battery CR2032 Coin Cell
7
Chapter 1
INTRODUCTION
User's Manual | CMS330-Q470E/H420E
www.dfi.com
SPECIFICATION
SYSTEM Processor 10th Generation Intel® LGA 1200 Socket Processors, TDP support up to 125W
Intel® Core™ i9-10900E (10 Cores, 20M Cache, up to 4.7 GHz); 65W
Intel® Core™ i9-10900TE (10 Cores, 20M Cache, up to 4.5 GHz); 35W
Intel® Core™ i7-10700E (8 Cores, 16M Cache, up to 4.5 GHz); 65W
Intel® Core™ i7-10700TE (8 Cores, 16M Cache, up to 4.4 GHz); 35W
Intel® Core™ i5-10500E (6 Cores, 12M Cache, up to 4.2 GHz); 65W
Intel® Core™ i5-10500TE (6 Cores, 12M Cache, up to 3.7 GHz); 35W
Intel® Core™ i3-10100E (4 Cores, 6M Cache, 3.8 GHz); 65W
Intel® Core™ i3-10100TE (4 Cores, 6M Cache, to 3.6 GHz); 35W
Intel® Pentium® G6400E (2 Cores, 4M Cache, 3.8 GHz); 58W
Intel® Pentium® G6400TE (2 Cores, 4M Cache, 3.2 GHz); 35W
Intel® Celeron® G5900E (2 Cores, 2M Cache, 3.2 GHz); 58W
Intel® Celeron® G5900TE (2 Cores, 2M Cache, 3.0 GHz); 35W
Chipset Intel® Q470E/H420E Chipset
Memory Q470E: Four 288-pin Non-ECC UDIMM up to 128GB
H420E: Two 288-pin Non-ECC UDIMM up to 64GB
Dual Channel DDR4 2400/2666/2933MHz
BIOS AMI SPI 256Mbit
GRAPHICS Controller Intel® HD Gen 9 Graphics
Feature OpenGL 4.5, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display 1 x VGA VGA: resolution up to 1920x1200 @ 60Hz
1 x DP++ DP++: resolution up to 4096x2160 @ 60Hz
1 x HDMI 1.4b HDMI: resolution up to 4096x2160 @ 24Hz
Multiple Dis-
plays Q470E: VGA + DP++ + HDMI
H420E: VGA + DP++ / VGA + HDMI / DP++ + HDMI
EXPANSION Interface 1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
2 x PCI
Q470E:
1 x M.2 2242/2260/2280 M key (PCIe Gen3 x4 NVMe/SATA/Intel® Optane Memory and intel RST
support)
1 x M.2 2230 E key (USB 2.0/PCIe)
H420E: N/A
AUDIO Audio Codec Realtek ALC888
ETHERNET Controller 1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PHY with iAMT12.0 (10/100/1000Mbps)
(Q470E: Core i9/ i7/i5 supports iAMT, H420E: N/A)
REAR I/O Ethernet 2 x GbE (RJ-45)
Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)
USB 2 x USB 3.2 (Q470E: Gen2; H420E: Gen1)
2 x USB 3.2 Gen1 (Q470E: Up to 6 x USB 3.2 Gen1, MOQ required)
2 x USB 2.0
Display 1 x VGA
1 x DP++
1 x HDMI
PS/2 1 x PS/2 (mini-DIN-6)
Audio 1 x Line-out
1 x Mic-in
1 x Line-in (opt., MOQ required)
INTERNAL I/O Serial 9 x RS-232 (2.54mm pitch)
USB 2 x USB 3.2 Gen 1
Q470E: 4 x USB 2.0 (2.54mm pitch, Colay vertical Type A, opt.: MOQ required)
H420E: 2 x USB 2.0 (2.54mm pitch, Colay vertical Type A, opt.: MOQ required)
Audio 1 x Front Audio Header
1 x S/PDIF
SATA 4 x SATA 3.0 (up to 6Gb/s, SATA 3) (Q470E: RAID 0/1/5/10, H420E: N/A)
DIO 1 x 16-bit DIO
LPC 1 x LPC
SMBus 1 x SMBus
WATCHDOG
TIMER Output &
Interval System Reset, Programmable via Software from 1 to 255 Seconds
SECURITY TPM Infineon TPM2.0 (opt., MOQ required)
POWER Type ATX
Connector 8-pin ATX 12V power
24-pin ATX power
Consumption Typical: i9-10900K: 3.3V @ 0.36A (1.19W); 5V @ 1.02A (5.1W); 12V @ 3.8A (45.6W)
Max.: i9-10900K:3.3V @ 0.38A (1.25W); 5V @ 1.82A (9.1W); 12V @ 15.64A (187.68W)
RTC Battery CR2032 Coin Cell
8
Chapter 1
INTRODUCTION
User's Manual | CMS330-Q470E/H420E
XFeatures
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so that
your system will continue to operate.
DDR4
DDR4 delivers increased system bandwidth and improves performance. The advantages of
DDR4 provide an extended battery life and improve the performance at a lower power than
DDR3/DDR2.
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
Gigabit LAN
Two Intel® Gigabit LAN controllers support up to 1Gbps data transmission.
Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-
agement Event) signal. However, if your system is in the Suspend mode, you can power-on the
system only through an IRQ or DMA interrupt.
Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The x4 PCI Express lane supports transfer rate of 4 Gigabyte per
second (2 directions). The PCI Express architecture also supports high performance graphics
infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth (8GB/s in
each direction).
ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Manage-
ment and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to go
through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating ses-
sion will resume exactly where you left off the next time you power-on the system.
Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
USB
The system board supports the new USB 3.2 Gen 1. It is capable of running at a maximum
transmission speed of up to 5 Gbit/s (625 MB/s), and is faster than USB 2.0 (480 Mbit/s, or 60
MB/s) and USB 1.1 (12Mb/s). USB 3.2 reduces the time required for data transmission, reduc-
es power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously acces-
sible external Plug and Play peripherals.
RTC Timer
The Real Time Clock (RTC) installed on the system board allows your system to automatically
power-on on the set date and time.
9
Chapter 1
INTRODUCTION
User's Manual | CMS330-Q470E/H420E
XBlock Diagram
www.dfi.com
MECHANICAL DRAWING
0
10.16
112.79
154.94
227.33
233.68
0
34.29
45.72
65.21
81.05
100.55
121.55
128.93
142.55
171.55
197.48
BLOCK DIAGRAM
10
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
Chapter 2 - Hardware Installation
XBoard Layout
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives,
add-in boards, and other components. Perform installation procedures at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
Note:
Some components are optional and only available upon request.
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
11
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
XSystem Memory
• Four 288-pin DIMM up to 128GB (Q470E) / Two 288-pin DIMM up to
64GB (H420E)
• Dual Channel DDR4 2400/2666/2933 MHz
Features
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits from the memory channels. DIMMs are on the same
channel. DIMMs in a channel can be identical or completely different. However, we highly rec-
ommend using identical DIMMs. Not all slots need to be populated.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
Before installing the memory module, please make sure that the following safety cautions are
well-attended.
• Make sure the PC and all other peripheral devices connected to it has been powered
down.
• Disconnect all power cords and cables.
• Locate the DIMM socket on the system board
• Make sure the notch on memory card is aligned to the key on the socket.
XSystem Memory
Installing the DIMM Module
Socket Side View
Socket Top View
Memory Module
Notch
Key
Eject TabEject Tab
DDR4_1
DDR4_2
DDR4_3
DDR4_4
12
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
Please follow the steps below to install the memory card into the socket.
Step 1:
Press the eject tabs at both ends of the socket outward and downward to release them from
the locked position.
Step 2:
Insert the memory card into the slot while making sure the notch and the key are aligned.
Press the card down firmly with fingers while applying and maintaining even pressure on both
ends.
Step 3:
The tabs snap automatically to the edges of the card and lock the card in place.
XSystem Memory
XInstalling the DIMM Module
Please follow the steps below to remove the memory card from the socket.
Step 1:
Press the eject tabs at both ends of the socket outward and downward to release them from
the locked position.
Step 2:
The memory card ejects from the slot automatically.
Step 3:
Hold the card by its edges and remove it from the slot.
XSystem Memory
Removing the DIMM Module
Step 3
Step 2
Step 1 Step 1
Step 2
Step 3
13
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
Installing the CPU Fan and Heat Sink
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circula-
tion across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
Before you place the heat sink on the CPU, you must apply a thermal paste onto the top of the
heat sink. The thermal paste is usually supplied when you purchase the fan with heat sink as-
sembly. Do not spread the paste all over the surface. When you later place the CPU on top of
the heat sink, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal paste if
the fan with heat sink already has a patch of thermal paste on its underside. Peel the strip that
covers the paste before you place the CPU on top of the heat sink.
XCPU
There are 4 screw holes around the CPU for the heat sink to be mounted.
Align the 4 screw holes and tighten the heat sink up by inserting screws, DO remember to con-
nect the fan cable on the board. (The location of fan connector may vary.)
14
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XJumper Settings
CLEAR CMOS Data
JP5
If any anomaly of the followings is encountered —
• a) CMOS data is corrupted;
• b) you forgot the supervisor or user password;
• c) failure to start the system due to BIOS mis-configuration
— it is suggested that the system be reconfigured with default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
• 1. Power-off the system and unplug the power cord.
• 2. Put a jumper cap on pin 2 and pin 3. Wait for a few seconds and set it back to its
default setting, i.e. jumper cap on pin 1 and pin 2.
• 3. Plug the power cord and power-on the system.
2-3 On: Clear CMOS Data 1-2 On: Normal (default)
13 2 13 2
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
1
DIO Power
JP13/11
JP13(DIO 8~11 PWR) / JP11(DIO 0~3 PWR)
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
65
21
1
SOJ2
1
2-3 On: GND 1-2 On: DIO Power (default)
13 2 13 2
15
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XJumper Settings
COM1 RS232/422/485 Select
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
(COM 1)
JP3/
JP2/
JP1
JP1/JP2/JP3 (for COM 1) are used to configure the COM ports to RS232, RS422 (Full Duplex)
or RS485. When COM 1 RS232/422/485 is selected, JP1 and JP2 must be set in accordance to
JP3.
JP1/JP2
1-3, 2-4 On:
RS232 (default) 3-5, 4-6 On:
RS422 Full Duplex 3-5, 2-4 On:
RS485
2 4 6
1 3 5
2 4 6
13 5
2 4 6
1 3 5
JP3
1-3, 4-6 On:
RS232 (default) 3-5, 4-6 On:
RS422 Full Duplex 3-5, 4-6 On:
RS485
2 4 6
13 5
2 4 6
13 5
2 4 6
1 3 5
16
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XJumper Settings
COM1 RS232 Power Select
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
JP4
(COM 1)
JP4 (for COM 1) is used to configure Serial COM ports to pure RS232 or RS232 with power.
The pin functions of COM 1 vary according to JP4’s setting respectively.
JP4 (COM 1)
1-3, 2-4 On:
RS232 (default) 3-5, 4-6 On:
RS232 with power
2 4 6
13 5
2 4 6
13 5
17
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XJumper Settings
AT/ATX Mode - JP26
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
JP26 is used to switch between AT/ATX Mode.
JP26
1 32
1-2 On:
AT Mode (default)
1 3
2
2-3 On:
ATX Mode
18
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XJumper Settings
USB Power Control - JP25
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
JP25 is used to determine the USB power.
JP25
2-3 On:
5V
132
1-2 On:
5VDU (default)
13
2
19
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
XRear I/O Ports
The rear panel I/O ports consist of the following:
• 1 PS/2 for KB/MS
• 2 USB 2.0
• 1 COM 1 port
• 1 VGA port
• 1 DP++
• 1 HDMI port
• RJ45 LAN 1/2
• 2 USB 3.2 Gen2 ports
• 6 USB 3.2 Gen 1 ports
• 1 Line-out jack
• 1 Mic-in jack
Line-out
Mic-in
VGA
PS2
HDMI USB 3.2
Gen 2
USB 2.0
COM 1 USB 3.2
Gen 1
LAN 1
DP++
LAN 2
USB 3.2
Gen 1
20
Chapter 2
HARDWARE INSTALLATION
User's Manual | CMS330-Q470E/H420E
DDR4_1 DDR4_2
DDR4_3 DDR4_4
LGA 1200
PCIE1 (PCIe x16)
PCI1
PCI2
PCIE2 (PCIe x4)
USB 7/8
(USB 2.0)
Mic In
Line Out
Line In
Note
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Buzzer
Battery
Intel
H420E/Q470E
ATX
power
Standby
Power
LED
1 13
12 24
1
210
1
210
USB 9/10 (USB 2.0)
USB 11/12
(USB 2.0)
Note
S/PDIF
1
2
19
M.2 E Key
2230
SATA0/1/2/3
(top to bottom)
SYS FAN2
1
M.2 M Key
224222602280
SYS FAN1 CPU FAN1
1
1
COM2/3/4/5
(top to bottom)
12
13
LPC
14
91
2
Front
Panel
1 2
11
SPI Flash
BIOS
1
LAN LED
Digital I/O (DIO)
Front
Audio
1
2
10
7
1
8
2
9
+12V Power
1
5
1
J10
HDMI
DP
VGA
91
91
91
SYS FAN3
1
1
2
5
J12
3
1
3
1
3
1
J34
19
J35
19
2
J36
19
J37
19
1
3
1
4
JP26
13
JP5
11
1 10
20
USB 3.2 Gen1
(USB 5/6)
JP24
HDDPWR
6
5
2
1
JP4/2/3/1
(top to bottom)
6
5
2
1
6
5
2
1
6
5
2
1
DIO Power
1 4
COM 6
1
2
9
JP13/11/25
(left to right)
65
21
1
SOJ2
USB Ports
The USB device allows data exchange between your computer and a wide range of simultane-
ously accessible external Plug and Play peripherals. The system board is equipped with mul-
tiple USB ports as listed below:
• 2 x USB 3.2 Gen 2 rear ports (USB3 1/2)
• 6 x USB 3.2 Gen 1 rear ports (USB3 3/4/7/8/9/10)
• 2 x USB 3.2 Gen 1 internal ports, box headers (USB3 5/6)
• 4 x USB 2.0 internal ports (USB2 9/10/11/12)
• 2 x USB 2.0 rear ports (USB2 7/8)
The internal USB ports may be mounted on a card-edge bracket. Install the card-edge bracket
to an available slot at the rear of the system chassis and then insert the USB port cables to a
connector.
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
Pin Assignment Pin Assignment
1SBV 2SBV
3Data- 4Data-
5Data+ 6Data+
7GND 8GND
9--- 10 N.C.
USB 2.0 Headers (USB 9/10/11/12)
XRear I/O Ports
USB 1/2 (USB 3.2 Gen 2)
USB 3/4 (USB 3.2 Gen 1)
USB 7/8/9/10 (USB 3.2 Gen 1)
Pin Assignment Pin Assignment
10 GND 11 USBP_C_5P
9USBP_C_6P 12 USBP_C_5N
8USBP_C_6N 13 GND
7GND 14 USB3_TX6_DP
6USB3_TX5_DP 15 USB3_TX6_DN
5USB3_TX5_DN 16 GND
4GND 17 USB3_RX6_DP
3USB3_RX5_DP 18 USB3_RX6_DN
2USB3_RX5_DN 19 SBV3
1SBV3 20 --
USB 3.2 Headers (USB 5/6)
10
91
2
USB 9/10/11/12 (USB 2.0)
221010
99
USB 5/6 (USB 3.2 Gen 1)
USB 7/8 (USB 2.0 )
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

DFI CMS330 Owner's manual

DFI
Brand
DFI
Model
CMS330
Category
Motherboards
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents