Sennheiser e 912 S bl User manual

Sennheiser
Brand
Sennheiser
Model
e 912 S bl
Category
Microphones
Type
User manual

This manual is also suitable for

912 S
Bedienungsanleitung
Instructions for use
Notice d‘emploi
Istruzoni per l‘uso
Instrucciones de uso
Gebruiksaanwijzing
e 912 S_516585_0207_Sp6.book Seite 1 Freitag, 28. September 2007 11:09 11
e 912 S_516585_0207_Sp6.book Seite 2 Freitag, 28. September 2007 11:09 11
1
912 S
The boundary microphone 912 S is a high-quality, pre-
polarized condenser microphone with half-cardioid pick-up
pattern, designed for picking up speech.
Due to its unobtrusive, flat design, it is ideally suited for use on
conference tables, altars and lecterns.
The microphone can be switched on and off via an integrated
membrane switch.
An internal DIP switch bank provides the following operating
modes:
y On/off (factory preset)
y Push-to-talk button (PTT)
y Push-to-mute button (PTM)
y Permanently switched on
The frequency response curve can be changed via a second DIP
switch bank:
y Low cut
y Low and high boost (factory preset)
y Low boost
y linear (= frequency response curve of the 912)
The 912 S is available in three different finishes:
y 912 S BK (black) Cat. No. 500875
y 912 S WH (white) Cat. No. 500876
y 912 S NX (Nextel non-reflecting gray) Cat. No. 502193
e 912 S_516585_0207_Sp6.book Seite 1 Freitag, 28. September 2007 11:09 11
2
Features
y Programmable membrane switch
y Programmable frequency response curve
y Very unobtrusive due to flat design
y Extremely rugged sound inlet basket
y Rubber damping plate on base to minimize structure-born
noise
y Mounting slots for mounting the microphone to table tops,
lecterns, etc.
y Gold-plated XLR connector
y Integrated electronics (instead of in-line preamp)
Delivery includes
y 912 S boundary microphone
y Pouch
y Instructions for use
y Warranty Certificate
e 912 S_516585_0207_Sp6.book Seite 2 Freitag, 28. September 2007 11:09 11
3
Postioning the microphone
Boundary microphones make use of the pressure effects at a
room boundary and need to be mounted on a flat surface:
*) The cardioid pick-up pattern has an opening angle of approx.
130°. Try to position the microphone so that the sound source
(conference participant, speaker or instrument) is located in
this angle area (see polar diagram).
Position Sound result Comments
Altar or lectern:
on a sound-reflecting
surface
Less room resonance
portions or comb filter
elements; improved
speech intelligibility
and greater gain
reserves in contrast to
freestanding micro
-
phones
Unobtrusive due to
flat design; no micro
-
phones in the field of
vision
Conference rooms:
lying on the table;
directed towards the
conference
participants *)
Less room resonance
in contrast to
freestanding
microphones
Microphones must
not be covered by
papers, folders or
similar objects
e 912 S_516585_0207_Sp6.book Seite 3 Freitag, 28. September 2007 11:09 11
4
Setting the operating mode and frequency
response curve
Position of
DIP switches
Operating
mode
쐃
Position of
DIP switches
Frequency
response curve
쐇
Permanently
switched on (ON)
Low cut, can be
used in all
operating modes
Push-to-talk
button (PTT)
Low boost
Push-to-mute
button (PTM)
Low and high
boost (factory
preset)
On/off (factory
preset)
linear
쐃
쐇
DIP switch bank:
(visible when rear side
is open)
쐃 Operating mode
쐇 Frequency response curve
1 2 3 4
1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
e 912 S_516585_0207_Sp6.book Seite 4 Freitag, 28. September 2007 11:09 11
5
Operating Mode 쐃:
y Permanently switched on:
disables the switch completely, the microphone is
permanently switched on.
y Push-to-talk (PTT):
The microphone is switched on as long as the membrane
switch is pressed.
y Push-to-mute (PTM):
The microphone is switched off as long as the membrane
switch is pressed.
y On/off (factory preset):
turns the switch into push to switch on, push again to switch
off.
Frequency response curve 쐇:
y Low cut:
reduces the bass frequencies to minimize structure-born
noise – this switch (1) is independent of the other three DIP
switches and can be used in any of the following conditions
(eg: you can use the low cut as well as the bass boost if
placing the microphone on a small table with a high risk of
structure-born noise).
y Low boost:
extends the bass response to compensate for putting the
microphone on a small table.
y Low and high boost (factory preset):
extends the frequency response at both ends.
y Linear:
is the natural response of the microphone.
e 912 S_516585_0207_Sp6.book Seite 5 Freitag, 28. September 2007 11:09 11
6
Polar diagram
e 912 S_516585_0207_Sp6.book Seite 6 Freitag, 28. September 2007 11:09 11
7
Frequency response curve
- 40
- 50
- 60
- 70
- 80
20
50
100
200
500
1000
2000
5000
10000
20000
Hz
Low and high boost (factory preset)
- 30
dBv
Rumble filter (low cut)
Low boost
Linear ( 912)
- 40
- 50
- 60
- 70
- 80
20
50
100
200
500
1000
2000
5000
10000
20000
Hz
- 30
dBv
e 912 S_516585_0207_Sp6.book Seite 7 Freitag, 28. September 2007 11:09 11
8
Specifications
Pin assignment of XLR-3 connector
Transducer principle pre-polarized condenser
microphone
Frequency response 20 – 20,000 Hz
Pick-up pattern half-cardioid
Sensitivity (free field, no load)
(1 kHz)
6 mV/Pa (factory preset)
10 mV/Pa (lin)
Nominal impedance (1 kHz) <100 Ω
Min. terminating impedance 1 kΩ
Phantom powering 48 V/2.8 mA
Max. sound pressure level (1 kHz) 134 dB SPL
Connector XLR-3
Weight 550 g
Dimensions L: 126.5 mm
W: 105 mm
H: 26.5 mm
12
3
1
2
3
+
+
12
3
XLR
+
XLRXLR
+
e 912 S_516585_0207_Sp6.book Seite 8 Freitag, 28. September 2007 11:09 11
9
Overview of microphone applications
Variant
Application
e901
e902
e904
e905
e906
e908B
e908B ew
e908D
e908T ew
e912
e912 S
e914
e935/e945
Vocals x
Choirs x x
Studio, acoustic
instruments
x x x
Orchestra x
Trumpet, trombone x x x
Saxophone x x x
Acoustic guitar x
Acoustic bass x
Guitar amplifiers x
Bass amplifiers x
Leslie x x x x
Piano, grand piano x x
Kick drums x x
Snare drums x x x x
Rack toms x x x x x
Floor toms x x x x x
Congas x x x x
Cymbals x
Percussion x x x x x x
Conference table,
altar
x x
Lectern x x
Theater stage x x
e 912 S_516585_0207_Sp6.book Seite 9 Freitag, 28. September 2007 11:09 11
10
Manufacturer Declarations
Warranty
2 years
CE Declaration of Conformity
Sennheiser electronic GmbH & Co. KG declare that this
device is in compliance with the applicable CE
standards and regulations.
WEEE Declaration
Please dispose of this product by bringing it to your
local collection point or recycling centre for such
equipment.
e 912 S_516585_0207_Sp6.book Seite 10 Freitag, 28. September 2007 11:09 11
Sennheiser electronic GmbH & Co. KG
30900 Wedemark, Germany
Phone +49 (5130) 600 0
Fax +49 (5130) 600 300
www.sennheiser.com
Printed in Germany Publ. 09/07 516585/A03
e 912 S_516585_0207_Sp6.book Seite 1 Freitag, 28. September 2007 11:09 11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Sennheiser e 912 S bl User manual

Sennheiser
Brand
Sennheiser
Model
e 912 S bl
Category
Microphones
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents