Tascam 202mkIV User manual
- Category
- Cassette players
- Type
- User manual
This manual is also suitable for
202MK%^
Double Auto Reverse Cassette Deck
D00935220B
»
OWNER'S MANUAL
IMPORTANT SAFETY PRECAUTIONS
2 TASCAM 202MKIV
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol, within equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous volt-
age” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
This appliance has a serial num-
ber located on the rear panel.
Please record the model number
an d se ri al n umber and retain
them for your records.
Model number
Serial number
TO THE USER
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications.
H o w ev e r, t h e r e i s n o g u a r a nt e e t h a t
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures.
a) Reor i e n t or re l o c a t e t h e re c e iving
antenna.
b) Increase the separation between the
equipment and receiver.
c) Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
d) Consult the dealer or an experienced
radio/TV technician for help.
CAUTION:
Changes or modifications to this equipment
n o t e x p r e s s l y a p p r o v e d b y T E A C
CORPO R ATIO N for co m p l iance cou l d
void the user's authority to operate this
equipment.
For U.S.A.
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 3
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.
8 Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that pro-
duce heat.
9 Do not defeat the safety purpose of the
polarized or grounding-type plug. A polar-
ized plug has two blades with one wider
than the other. A grounding type plug has
two blades and a third grounding prong. The
wide blade or the third prong are provided
for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked
on or pinched particularly at plugs, conve-
nience receptacles, and the point where
they exit from the apparatus.
11 Only use attachments/accessories specified
by the manufacturer.
12 Use only with the cart, stand, tripod, brack-
et, or table specified by the manufacturer,
or sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14 Refer all servicing to qualified service per-
sonnel. Servicing is required when the appa-
ratus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not oper-
ate normally, or has been dropped.
• Do not expose this apparatus to drips or
splashes.
• Do not place any objects filled with liquids,
such as vases, on the apparatus.
• Do not install this apparatus in a confined
space such as a book case or similar unit.
• The apparatus draws nominal non-operating
power from the AC outlet with its POWER
switch in the off position.
• The apparatus should be located close
enough to the AC outlet so that you can
easily grasp the power cord plug at any
time.
• An apparatus with Class I construction shall
be connected to an AC outlet with a protec-
tive grounding connection.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
IMPORTANT SAFETY PRECAUTIONS
4 TASCAM 202MKIV
Contents
1 − Introduction .........................5
Supplied accessories .................... 5
Rack-mounting the unit ............... 5
About this manual ....................... 5
Precautions and notes for
placement and use ................... 6
About cassette tapes ................... 6
Cassette tapes that you should not
use..........................................6
Automatic tape type detection
function .................................7
Tape slack ..........................................7
Accidental erasure prevention
tabs ........................................7
Maintenance .....................................7
Cleaning the heads ................................ 7
Connections .................................. 8
2 − Features of the 202MKIV .....9
Front panel .................................... 9
Rear panel ................................... 10
Display ......................................... 11
3 − Playback .............................. 12
Playback 1 (either TAPE 1 or
TAPE 2) .................................... 12
Playback 2 (either TAPE 1 or
TAPE 2) .................................... 13
Continuous playback ................. 14
Blank scan ................................... 14
Song search ................................. 15
Intro check .................................. 16
4 − Recording ........................... 17
Recording (either TAPE 1 or
TAPE 2) .................................... 17
To erase recordings .................... 18
Quick record start ...................... 18
To stop recording temporarily ........... 18
Recording silence ....................... 19
To create a blank of more than 4
seconds long .............................. 19
To create a blank of less than 4 seconds
long ............................................. 19
Mic mixing recording ................. 19
Adjusting mix recording level .......20
Continuous recording ................ 20
Parallel recording ....................... 21
Dubbing (from TAPE 1 to
TAPE 2) .................................... 22
Editing during dubbing (only at
normal speed) ........................ 23
Synchro reverse dubbing (from
TAPE 1 to TAPE 2).................... 23
Timer playback ........................... 24
Playback ..........................................24
Timer-controlled recording ...........25
Connections ....................................25
5 − Reference and
specifications ....................26
Troubleshooting ......................... 26
Specifications ............................. 27
Dimensional drawing ................. 27
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 5
Thank you for your purchase of the TASCAM
202MKIV Double Auto Reverse Cassette Deck.
Before connecting and using the unit, please take
time to read this manual thoroughly to ensure you
understand how to properly set up and connect the
202MKIV, as well as the operation of its many use-
ful and convenient functions. After you have finished
reading this manual, please keep it in a safe place for
future reference.
Dolby NR
Dolby NR is designed to reduce tape hiss, a noise
introduced during the recording and playback process-
es. This cassette deck is equipped with Dolby B-type
Noise Reduction.
The Dolby NR system affects both recording and
playback quality. In playback, be sure to set the
DOLBY NR switch to the same position used when
the recording was made.
Manufactured under license from Dolby Laboratories.
HX Pro headroom extension originated by Bang and
Olufsen.
Dolby, HX Pro, and the double-D symbol are trade-
marks of Dolby Laboratories.
Rack-mounting the unit
If you are mounting the unit in a rack, leave 1U of
space above it and 4 inch (10 cm) or more of space at
the rear.
Use the rack-mounting kit to mount the unit in a stan-
dard 19-inch equipment rack, as shown in this section.
Remove the feet of the unit before mounting.
Supplied accessories
In addition to this manual, the 202MKIV has been
packed with the following:
• A rack-mounting screw kit (screws and washers) ...
1
• A warranty card ......................................................
1
Contact your TASCAM supplier if any of these items
are missing.
About this manual
In this manual, we use the following conventions:
The names of keys and controls are given in the fol-
lowing typeface: EJECT.
The alphanumeric portion of the display shows a
message, this is shown in the following typeface:
CP01.
If a preset indicator in the display (i.e. one which
cannot change, but is either on or off) is shown,
this is shown as follows: PARALLEL.
•
•
•
1 − Introduction
IMPORTANT SAFETY PRECAUTIONS
6 TASCAM 202MKIV
1 − Introduction
Precautions and notes for placement and use
The 202MKIV may be used in most areas, but to
maintain top performance, and prolong operating life,
observe the following notes, precautions and environ-
mental conditions:
Avoid exposing it to extremes of temperature and
humidity and avoid mechanical shocks and vibra-
tion.
Keep the unit away from strong magnetic fields
(TV sets, computer monitors, large electric motors,
etc.).
The nominal temperature should be between 5°C
and 35°C (41°F and 95°F).
Relative humidity should be 30 to 90 percent.
As the unit may become hot during operation,
always leave sufficient space above the unit for
ventilation. Do not install this unit in a confined
space such as a bookcase, and do not put anything
on top of the unit.
Avoid installing this unit on top of any heat-gener-
ating electrical device such as a power amplifier.
Make sure that the unit is mounted in a level posi-
tion for correct operation.
•
•
•
•
•
•
•
Do not open the sealed cabinet as this might result
in damage to the circuitry or electrical shocks. If
a foreign object should get inside the unit, contact
your supplier or service agency.
When removing the power plug from the wall out-
let, always pull directory on the plug, never yank
the cord.
The voltage selector on the rear panel is only
available on units for the North American market.
Please set this to match your local supply. If you
are in any doubt in this matter, consult an electri-
cian
NOTE
When transporting the unit, always use the
original packing materials. For this reason, we
strongly recommend that you save all the pack
-
ing materials that came with the 202MKIV,
in case you need to transport it in the future.
In addition, when transporting the unit, you
should tape the cassette decks closed, using an
adhesive tape that will not spoil the finish of
the unit.
•
•
•
CAUTION
Do not open the cassette or pull the tape out of
the cassette.
Do not touch the tape surface.
Do not use or store the tape in a humid or dusty
place.
•
•
•
Keep the tape away from any magnetic sources,
such as speakers or TVs, otherwise noise may be
produced during playback or important record
-
ings may be erased.
•
About cassette tapes
Cassette tapes that you should not use
Poor performance, errors, or malfunctions may result
if you use any of the tapes described below. Some of
these tapes may also cause tape clog problems that can
damage the tape transport mechanism.
Cassettes that are imperfectly shaped
Do not use a deformed cassette or one that has unsta-
ble tape movement or makes a strange sound during
fast-forward or rewind.
Long play tapes
Do not use C-120 or longer tapes. These tapes are very
thin and can easily stretch or get tangled in the tape
transport mechanism.
Endless tapes
Do not use these tapes because they can easily get
tangled in the tape transport mechanism.
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 7
1 − Introduction
Automatic tape type detection function
This cassette deck can detect what type of tape is
being used based on the detection holes in the cassette
shell. Be sure to use cassettes with detection holes.
With this cassette deck, you can play back normal
(Type I), chrome (Type II) and metal (Type IV) tapes.
For recording, use normal (Type I) or chrome (Type
II) tapes.
Each deck (TAPE 1 and TAPE 2) is equipped with its
own auto tape type detection function, so you can use
different types of tape at the same time.
Metal
(
Type
IV
)
Automa
tic
t
ape typ
e de
tect
ion hol
es
Cr
O
2
(
Type
II
)
Normal
(
Type
I
)
Slack can cause the tape to get tangled in the capstan
or other rotating parts. To prevent this, take up all tape
slack using a pencil or the like inserted into the reel
hole.
Tape slack
Tabs on top of the cassette shell allow you to prevent
important recordings from being erased by mistake.
There are two tabs on each cassette shell: one for side
“A” and the other for side “B”.
Once these tabs have been removed using a screw-
driver or the like, there is absolutely no chance of the
recording function being activated.
To record on a cassette whose tab has been broken off,
stick a piece of adhesive tape over the hole. Be careful
not to block the tape type detection holes.
Accidental erasure prevention
tab for side “A”
Side “A”
Accidental erasure prevention tabs
If the surface of the deck becomes soiled, wipe it
clean with a dry, soft cloth. To remove stubborn dirt,
wipe with a cloth slightly moistened with a solution
of mild detergent and water, then moisten a cloth with
water, wring it well, and rub over the surface.
Do not allow the deck to remain in contact with rub-
ber or vinyl products for a long period of time, as
these could damage the surface finish.
Never use volatile cleaners like thinners, benzine or
alcohol because they will damage the surface finish.
CAUTION
For safety, always unplug the power cord be-
fore performing any maintenance.
Cleaning the heads
If the head section gets dirty, the recording quality will
deteriorate, resulting in degraded playback sound or
“drops” in sound. Also, if the tape transport path gets
dirty, the tape may get entangled in the rotating parts.
It is therefore recommended that the heads, pinch roll-
ers and capstans be cleaned regularly at intervals of
10-hour use with a cotton swab moistened with a com-
mercially available, appropriate cleaning liquid.
ª
Maintenance
IMPORTANT SAFETY PRECAUTIONS
8 TASCAM 202MKIV
1 − Introduction
Connections
CAUTION
Plug the power cord into an AC outlet only after
having made all other connections.
Read the instructions of each component you
intend to use with this unit.
Use the supplied RCA cables to make connections
between this unit and your amplifier. Make sure to
connect:
White plug to White jack (L: left channel)
Red plug to Red jack (R: right channel)
NOTE
Plugs must be firmly inserted into the corre-
sponding jacks. Do not bundle the RCA cables
together with the power cord and speaker
cables. Doing so will degrade sound quality or
generate noise.
•
•
Plug this AC power cord into an AC wall socket.
NOTE
Hold the power plug when plugging or unplug-
ging the power cord. Never pull or yank on the
power cord.
Unplug the power cord when you are not going
to use the unit for some time.
•
•
LL RR
PLAYREC
TAPE
NOTE
Do not make a recording or play back tape
when the tape transport path is wet with clean
-
ing liquid, as this could cause the tape to jam or
clog.
Pinch roller
Capstan
Erase head
Record/playback head
Pinch roller
Capstan
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 9
Front panel
1Power switch
This switch toggles the unit on/off.
NOTE
The equipment draws nominal non-operating
power from the AC outlet with its POWER
switch in the OFF position.
2TAPE 1 compartment
3INTRO CHECK key
Pressing this key allows you to identify recorded
segments by listening to the first 15 seconds of each
segment.
4COUNTER RESET keys
Pressing these keys reset the tape counter readings
for TAPE 1 and TAPE 2, respectively.
5Synchro reverse key (SYNC REV)
Pressing this key activates the synchro reverse dub
-
bing function.
6BLANK SCAN key
This key toggles Blank Scan on/off.
7Display
This shows tape counters, level meters, etc.
8Parallel record key (PARALLEL REC)
This key lets you simultaneously record on both
decks.
9Dubbing start key (DUB START)
This key is used when copying the contents of a
tape from TAPE 1 to TAPE 2, either at normal or
high speed.
0TAPE 2 compartment
qReverse mode switch (REV MODE)
This switch is used to switch between reverse
modes.
w TIMER switch
This switch is provided for use with a commercially
available audio timer, to allow timer controlled
recording or playback.
Normally, leave this switch to the
OFF position.
eDOLBY NR switch
This switch toggles the Dolby Noise Reduction sys
-
tem on/off. In playback you need to set this switch
to the same position as when the recording was
made.
rEJECT keys
Pressing these keys opens the TAPE 1 and TAPE 2
compartments.
tTape transport control keys
RECORD
Pressing this key shifts the corresponding deck to
record-pause mode.
PAUSE
Pressing this key temporarily stops playback or
recording.
Recording mute (REC MUTE)
This key is for creating the 4-second blank space
needed for proper operation of the Computomatic
Program Search (CPS) function.
2 − Features of the 202MKIV
IMPORTANT SAFETY PRECAUTIONS
10 TASCAM 202MKIV
2 − Features of the 202MKIV
m/,
Fast-forward/Rewind
H
Stop of playback/record
h / y
Reverse side play/Forward side play
yHeadphones jack (PHONES)
Plug your headphones into this jack.
uPITCH CONTROL
This control is used to vary the playback speed.
oREC LEVEL control
This control is used to adjust the recording level.
o MIC jack and level control
Insert your microphone into this jack and use the
knob to adjust the level of mic input.
NOTE
The MIC jack is mono. You cannot use a stereo
microphone with this cassette deck.
Rear panel
1
3
2
1LINE IN and LINE OUT jacks
Use the supplied RCA cables to make connections
between this unit and your amplifier. Make sure to
connect:
White plug to White jack (L: left channel)
Red plug to Red jack (R: right channel)
2 VOLTAGE SELECTOR
Switches the voltage tp either 230 V or 120 V.
NOTE
The voltage selector is only available on units
for North American market.
•
3AC power cord
Plug this AC power cord into an AC wall socket.
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 11
2 − Features of the 202MKIV
Display
1Peak level meter
This shows recording and playback levels.
2SYNC REV
This indicator lights when the synchro reverse dub
-
bing function is switched on.
3PARALLEL
This indicator lights to indicate parallel recording is
taking place.
4BLANK SCAN
This indicator lights to indicate the corresponding
function is switched on.
5Playback/recording direction indicator of TAPE
1 deck
6Pause indicator
This indicator lights when the TAPE 1 deck is tem
-
porarily stopped.
7Tape counter of TAPE 1 deck
The tape counter indicates the relative position of
the tape. You can reset the counter to zero whenever
you want.
During a CPS function, the tape counter shows
CP
and your specified number of songs to skip ahead or
back.
8Record indicator
This indicator lights when the TAPE 1 deck is in
record mode.
9Play indicator
This indicator lights when the TAPE 1 deck is in
play mode.
0Dubbing indicator
NORMAL DUB lights during normal speed dubbing, and
HIGH DUB lights during high speed dubbing.
qPlay indicator
This indicator lights when the TAPE 2 deck is in
play mode.
wRecord indicator
This indicator lights when the TAPE 2 deck is in
record mode.
eTape counter of TAPE 2 deck
The tape counter indicates the relative position of
the tape. You can reset the counter to zero whenever
you want.
During CPS operation, the tape counter shows
CP
and the number of songs you have specified to skip
ahead or back.
rPause indicator
This indicator lights when the TAPE 2 deck is tem
-
porarily stopped.
tPlayback/recording direction indicator of TAPE
2 deck
1
2
3 4
5
6
7 8
9 0
q w
e
rt
IMPORTANT SAFETY PRECAUTIONS
12 TASCAM 202MKIV
Playback 1 (either TAPE 1 or TAPE 2)
1. Switch on the POWER.
2. Load a pre-recorded tape into the TAPE 1 or 2
deck.
Press the
EJECT key (ø) to open the cassette
compartment. Insert the cassette tape with its
open edge facing down, the desired side facing
you. Then, close the cassette compartment by
pushing on its front part.
Side “A” facing you
This cassette deck can play back Normal (Type I),
Chrome (Type II) and Metal (Type IV) tapes.
For the sake of simplicity, we refer to the tape side
facing you as Side “A” and to the tape side facing
away as Side “B”. When you insert a cassette with
Sides “A” and “B” reversed, Side “A” should read
Side “B” and Side “B” should read Side “A”.
3. Select a reverse mode setting using the
REV
MODE switch.
You have a choice of three settings:
Ä: One way mode
Set the switch to this position to playback
only one side.
Ë: Two way mode
Set the switch to this position to play back
both sides of the tape in one session. When
playback reaches the end of side “A”, the
playback direction is automatically reversed,
and playback continues on side “B”.
ä: Repeat mode
Set the switch to this position. Both sides
of the tape in the Tape 1 deck is played back
continuously until you stop the operation,
and both sides of the tape in the Tape 2 deck
is played back as many as 5 times.
4. Set the
DOLBY NR switch.
Set the switch to the ON position when playing
back tapes recorded with Dolby NR.
To play tapes recorded without Dolby NR, set the
switch to the OFF position.
5. Press the
PLAY key (˙ or ¥).
Pressing the ¥ key starts playback from side
“A”.
Playback stops when reaching the end of side “A”
if the reverse mode is set to Ä. If the reverse
mode is set to Ë, playback continues on side
“B”, stopping at the end of side “B”. If the reverse
mode is set to ä, playback cycles through both
tape sides 5 times.
Pressing the
˙ key starts playback from side
“B”.
Playback stops when reaching the end of side “B”
if the reverse mode is set to either Ä or Ë. If
the reverse mode is set to ä, side “B” is played
back, and then playback cycles through both tape
sides 4 times.
3 − Playback
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 13
3 − Playback
Playback 2 (either TAPE 1 or TAPE 2)
A. To stop playback, press the STOP key (ª).
B. To stop playback temporarily, press the PAUSE
key. To resume playback, press the
PAUSE key
again, or press the
PLAY key (˙ or ¥).
While playback is paused, pressing the PLAY key
whose direction is opposite to the indicator (˙ or
¥) on the display, will switch the playback direc-
tion. This does not release the pause function.
Press PAUSE or the same play key (˙ or ¥) again
to start playback on the other side of the tape.
C. Fast forward/Rewind
Press the
Ô or , key while in stop mode to
fast wind the tape.
To stop the fast winding tape, press the STOP
key (
ª).
D. Tape counter
Press the
COUNTER RESET key to reset the
tape counter to
0000. You can use this func-
tion for easy relocation of any desired point on
the tape.
E. Pitch control (TAPE 1 deck only)
This control varies the pitch of the music dur
-
ing playback (This control does not work dur
-
ing recording or dubbing)
.
Turning the PITCH CONTROL knob clockwise
increases the playback speed and raises the pitch
up to +10%.
Turning the
PITCH CONTROL knob counter-
clockwise reduces the playback speed and lowers
the pitch by a maximum of –10%.
F. To listen through headphones
WARNING
There is no level control for the headphones
output. Beware that sudden loud sounds may
occur depending on recorded material. You
should avoid prolonged exposure to high vol
-
ume sound as this can damage your hearing.
Plug your headphones into the PHONES jack,
and put on the headphones.
Plugging into the PHONES jack does not disable
the line outputs.
IMPORTANT SAFETY PRECAUTIONS
14 TASCAM 202MKIV
3 − Playback
3
3
Continuous playback can be performed between
TAPE 1 and TAPE 2. When one tape is played back to
the end, the other tape automatically starts playback,
in a relay fashion.
1. Load pre-recorded tapes into the TAPE 1 and
TAPE 2 compartments.
2. Set the
DOLBY NR switch.
Always set the DOLBY NR switch to the same
position that was used for recording.
3. Set the
REV MODE switch to the ä (CONT
PLAY) position.
4. Press the PLAY key (˙ or ¥) of the deck you
want to start rst.
You can start continuous playback from either
TAPE 1 or TAPE 2.
Playback cycles through four tape sides as fol
-
lows, and will continue until you stop the opera-
tion.
TAPE 1 Side“A”
∑ Side “B”
™ ≈
TAPE 2 Side “B” ß Side “A”
Continuous playback
Blank scan
The Blank Scan function detects 10 seconds or more
of blank and skips over it.
To activate this function, press the BLANK SCAN key
followed by the desired play key (˙ or ¥).
The BLANK SCAN indicator lights when this function is
activated.
To disable this function, press the BLANK SCAN key
again. The indicator turns off.
Very quiet passages in music are likely to be identified
as blanks. If you are worried about this, switch off
Blank Scan.
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 15
3 − Playback
Song search
This cassette deck is equipped with the Computomatic
Program Search (CPS) function. This function detects
blank spaces (longer than 4 seconds) between songs
and fast-winds the tape in the forward or backward
direction skipping over the specified number of songs,
thus allowing direct access to the beginning of a
desired song. CPS can skip up to 20 songs ahead of or
behind the current song.
When you press the Ô or , key during playback,
the tape counter reads CP 01 and the tape starts
running at high speed in the pressed direction. Each
time you press the same direction key, the displayed
number increases by one integer. The number decreas-
es as you press the opposite direction key.
If you are listening to a song and want to go back to
the previous song, press the locator key opposite to
the playback direction twice. Pressing it just once will
take you back to the beginning of the current song.
Each additional press of the key will take you back
one song.
Display of TAPE 1:
The search range varies depending on REV MODE
switch settings.
Ä: Only one side of tape.
Ê: Both sides of the tape when searching in the
same direction as playback. Or, only one side
of the tape when searching in the opposite
direction as playback.
ä: Both sides followed by the first side (side “A”
∑ side “B” ∑ side “A” if CPS is started when
the tape’s forward side (facing you) is playing; or
side “B” ∑ side “A” ∑ side “B” if CPS is started
when the tape’s reverse side (facing away) is play
-
ing)
NOTE
The CPS function may not work properly if
blanks between songs are less than 4 seconds
long or contain noise.
IMPORTANT SAFETY PRECAUTIONS
16 TASCAM 202MKIV
3 − Playback
Intro Check plays the first 15 seconds of each song,
allowing you to quickly find the song you are looking
for.
Press the INTRO CHECK key during playback or
stop. The tape will fast wind in the same direction as
playback. When you find the desired song, press the
INTRO CHECK key again to start playback.
The tape counter reports how many songs have been
intro-checked so far.
The Intro Check range varies depending on REV
MODE switch settings:
Ä: Checks one side of the tape.
Ê: Checks both sides of the tape.
ä: Checks both sides of tape then double checks
the first side (side “A”
∑ side “B” ∑ side “A”
if Intro Check is started on the tape’s forward
side (facing you); or side “B”
∑ side “A” ∑
side “B” if Intro Check is started on the tape’s
reverse side (facing away).
Activating the Intro Check function during normal
playback will cause it to skip to the next song: play-
back of the current song is interrupted midway.
The tape automatically stops upon completion of the
check operation.
NOTE
Make sure that the TAPE 1 compartment is emp-
ty when starting Intro Check on TAPE 2.
The Intro Check function may not work properly
if blanks between songs are less than 4 seconds
long or contain noise.
•
•
Intro check
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 17
TASCAM 202MKIV 17
Recording (either TAPE 1 or TAPE 2)
1. Turn on the power.
2. Load a tape for recording.
Side “A” facing you
Press the EJECT key (ø) to open the cassette
compartment. Insert the cassette tape with its
open edge facing down, side “A” facing you.
Then close the cassette compartment by push
-
ing in the cassette door until it clicks shut.
NOTE
If the erasure prevention tabs of the loaded cas-
sette tape have been broken off, stick a piece of
adhesive tape over the hole(s).
With this cassette deck you can use Normal (Type
I) and Chrome (Type II) tapes for recording.
3. Set the REV MODE switch.
Ä: Set to this position to record on one side
only.
Ê or ä: Set to either of these positions to
record on both sides.
•
•
4. Set the
DOLBY NR switch.
Set the switch to ON to record with Dolby Noise
Reduction.
Set to
OFF to record without Dolby Noise Reduc-
tion.
5. Press the
RECORD key.
The deck enters the record-pause mode. π and
will light on the display.
6. Adjust the recording level.
Start playback of your recording source and set
the REC LEVEL control knob so that the level
meter indicates “0 dB” at peaks.
7. Set the recording direction.
Recording is made in the direction indicated by
the play/record direction indicator (˙/¥). To
change this direction, press the opposite direction
play key (˙ or ¥).
NOTE
Be careful not to press play key whose arrow
points in the same direction as the indicator.
Doing so will start recording.
4 − Recording
IMPORTANT SAFETY PRECAUTIONS
18 TASCAM 202MKIV
4 − Recording
8. When everything is ready, start recording by
pressing the
PAUSE key or the play key whose
arrow points in the same direction as the indi
-
cator.
To record on both tape sides, set the REV MODE
switch to Ê or ä and press the forward play
key (y). If you press the reverse PLAY key (h),
recording will be done only on side “B”.
To stop recording, press the stop key (ª).
A To stop recording temporarily
Press the PAUSE key to stop recording temporarily.
A second press of the key resumes recording.
To erase recordings
When you make a recording, the tape is overwritten
(previous recording is erased). To erase a tape without
making a new recording, set the REC LEVEL control
to the minimum (0) position and press the RECORD
key followed by the PLAY key (h or y).
Quick record start
Hold down the RECORD key and press the PLAY key
(h or y) corresponding to the direction you want the
tape to run.
IMPORTANT SAFETY INSTRUCTIONS
TASCAM 202MKIV 19
4 − Recording
TASCAM 202MKIV 19
Use this function to create blanks between songs
for proper operation of the Computamatic Program
Search (CPS) function.
Press the REC MUTE key when recording reaches the
desired point. No signal is recorded for about 4 sec-
onds and then the deck enters the record-pause mode.
To resume recording, press the PAUSE key.
To create a blank of more than 4 sec-
onds long
Hold down the REC MUTE key for the desired length
of time. When you release the key, the deck enters the
record-pause mode.
To create a blank of less than 4 sec-
onds long
Press the PAUSE key within 3 seconds of pressing the
REC MUTE key.
NOTE
If you press the REC MUTE key when the deck is
in the record-pause mode, no signal is recorded
for about 4 seconds, and then the deck shifts
back to the record-pause mode.
ª
ª
Recording silence
Mic mixing recording
This function allows you to record your voice and
another audio source together on a cassette tape.
The mic sound is fed into both the Left and Right
channels so it is located in the center of the stereo
image.
You have the choice of either selecting the audio
source you want on the amplifier connected to the
LINE IN jacks of the deck, or plugging the desired
source directly into the deck’s LINE IN jacks.
NOTE
To prevent feedback (howling), disable the
speaker outputs from the amplifier. Use head
-
phones to monitor recording.
This cassette deck is not compatible with stereo
mics. Always use a mono mic.
•
•
IMPORTANT SAFETY PRECAUTIONS
20 TASCAM 202MKIV
4 − Recording
To record a mix of voice and another audio source,
you need to adjust the mic input level and then fine
tune the overall recording level.
1. Plug your microphone into the
MIC jack on the
front panel.
2. Start playing the audio source, switch the deck
into the record-pause mode (by pressing the
RECORD key), and temporarily adjust the REC
LEVEL control to a relatively low level.
3. Speak into the mic and adjust the
MIC level
control to get the optimum balance between
your voice and the other source.
4. Fine tune the overall recording level using
the
REC LEVEL control so that the level meter
reads 0 dB at peaks.
5. When everything is ready, start recording as
instructed earlier in this manual.
Audio source
Adjustment of
mic input level
Adjustment of overall
recording level
Adjusting mix recording level
This function allows you to make uninterrupted
recordings on both sides of two tapes.
1. Load cassette tapes for recording into the
TAPE 1 and TAPE 2 compartments.
Side “A” facing you
2. Set the REV MODE switch to the ä (CONT
REC/PLAY) position.
Set the DOLBY NR switch to the ON position if
you want to.
3. Press the TAPE 1 deck’s
RECORD key.
The deck enters the record-pause mode. π and
will light on the display. Now adjust the
recording level and any other settings, as re-
quired.
Continuous recording
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Tascam 202mkIV User manual
- Category
- Cassette players
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Tascam CC-222mkIII Consultant’s Specification
-
-
-
Tascam CC-222SL User manual
-
-
-
-
-
-