Amana 4KAED4900BW1 Installation guide

Page is loading ...

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.kofFi,o..

- Clothes dryer installation must be performed by a qualified installer.

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers, Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire,

= To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

FOR YOUR SAFETY

1. Do not use or store gasoline or other flammable materials in this appliance or near this appliance.

2. Do not spray aerosols in the vicinity of this appliance while it is in operation.

3. Do not modify this appliance.

2

IM PORTANT SAFETY INSTRUCTIONS

WARNING." To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic

precautions, including the following:

[] Read all instructions before using the dryer. _J_

[] Keep a minimum clearance of 100 mm (4 in.) between the

rear of the dryer and any wall.

[] The operation of this appliance may affect the operation of

other types of appliances which take their air supply for safe

combustion from the same room. There has to be adequate

ventilation to replace exhausted air and thus avoid the

back-flow of gases into the room from appliances burning

other fuels, including open fires, when operating the tumble

dryer. If in doubt, consult the appliance manufacturers.

[] Do not obstruct the air supply to the dryer (see Installation

Instructions for minimum clearances).

[] Do not place items exposed to cooking oils in your dryer.

Oil-affected items can ignite spontaneously, especially when

exposed to heat sources such as in a tumble dryer. The

items become warm causing an oxidation reaction in the oil.

Oxidation creates heat. If the heat cannot escape, the items

can become hot enough to catch fire. Piling, stacking or

storing oil-affected items can prevent heat from escaping

and so create a fire hazard.

[] If it is unavoidable to dry in the dryer items that have been

soiled with substances such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes and wax

removers, or that have been contaminated by hair care

products, should be washed in hot water with an extra

amount of detergent before being dried in the dryer. These

items may give off vapours that could ignite or explode. Such

washing will reduce, but not eliminate, the hazard.

[] This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instructions concerning

use of the appliance by persons responsible for their safety.

[] Children should be supervised to ensure that they do not

play with the appliance.

[] The dryer should not be used if industrial chemicals have

been used for cleaning.

[] Before the dryer is removed from service or discarded,

remove the doors to the drying compartment.

[] Do not reach into the dryer if the drum is moving. A door

switch is fitted for your safety.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not continue to use this appliance if it appears to be

faulty.

[] Do not repair or replace any part of the dryer or attempt

any maintenance unless specifically recommended in this

Use and Care Guide. Repairs and servicing should only

be carried out by competent service personnel.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product. Follow their instructions.

[] Clean dryer lint screen before or after each load. Do not

operate dryer without lint screen in place.

[] Keep area around the exhaust and inlet openings and

adjacent surrounding areas free from the accumulation of

lint, dust, and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See Installation Instructions for earthing instructions.

[] Do not dry unwashed items in this dryer.

[] The final part of a tumble dryer cycle occurs without heat

(cool down cycle) to ensure that the items are left at a

temperature that ensures the items will not be damaged.

[] kems such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes or

pillows fitted with foam rubber pads must only be dried

on a clothesline.

[] If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified

person in order to avoid a hazard.

WARNING: Never stop a tumble dryer cycle before the

end of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated.

SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Tools and Parts:

Gather required tools and parts before starting installation.

@

Flat-blade screwdriver

#2 Phillips screwdriver

6,2 mm (1/4") nut driver Adjustable wrench that

opens to 25 mm (1") or a

hex-head socket

Utilityknife Tapemeasure

Pliers

Level

Caulkinggunandcompound

forinstallingnewexhaustvent

Wirestripper

(directwireinstallations)

Tinsnips

(newventinstallations)

Parts supplied (all models):

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts

are included.

Parts needed: (not supplied with dryer)

[] Electric Cord and Plug

[] Vent clamps

[] Vent elbows and ductwork

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with dryers.

The kit should contain:

[] A UL listed 30-amp power supply cord, rated 240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

[] A UL listed strain relief.

Additional parts may be required, depending on your installation.

Check local codes. Check existing electrical supply and venting.

Read "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

LOCATION REQUIREMENTS

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 460 mm (18 inches) above the floor

for a garage installation.

Failure to do so can result in death, explosion,

or fire.

Select proper location for your dryer to improve performance

and minimize noise. Check code requirements. Some codes limit,

or do not permit, installation of the dryer in garages, closets,

mobile homes, or sleeping quarters. Contact your local building

inspector.

You will need:

[] A location that allows for proper exhaust installation. The

dryer must be exhausted to the outdoors. See "Venting

Requirements."

[] A floor that will support the dryer and a total weight (dryer

and load) of 90,7 kg (200 Ibs). The combined weight of a

companion appliance should also be considered.

[] A level floor with maximum slope of 25 mm (1") under entire

dryer. If slope is greater than 25 mm (1"), install Extended

Dryer Feet Kit. Clothes may not tumble properly and models

with automatic sensor cycles may not operate correctly if

dryer is not level.

[] It is important to make sure the room has an adequate air

supply for drying operation. The operation of this appliance

may affect the operation of other appliances which take their

air supply for safe combustion from the same room.

[] Adequate ventilation must be provided to avoid a backflow

of gases into the room from appliances burning other

fuels, including open fires. If in doubt consult the appliance

manufacturers.

iMPORTANT: The dryer must not be installed or stored in an

area where it will be exposed to water and/or weather. Do not

operate your dryer at temperatures below 7°C (45°F). At lower

temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended. Check code

requirements. Some codes limit, or do not permit, installation of

the dryer in garages, closets, or sleeping quarters. Contact your

local building inspector.

Proper installation is your responsibility.

4

Installation clearances:

For each arrangement, consider allowing more space for ease of

installation and servicing; spacing for companion appliances and

clearances for walls, doors, and floor moldings. Space must be

large enough to allow door to fully open. Add spacing on all sides

of dryer to reduce noise transfer. If a closet door or Iouvered door

is installed, top and bottom air openings in door are required.

Dryer Dimensions

Front View:

_686 mm_

(27)

1095 mm

(431/8"}

_578 mm_

(22 3/4"}

489 mm

(191/o"}

Side View:

m

_743 rnm_

356 mm _- (29 1/4 ) r

(14")

Side View of Side Swing Door:

{101/4")

_578 mm_

(22 3/4")

_743 mm_

(29 1/4")

?-

260 mm4_

(101/4")

108 mm

(41/4'')

108 mm

(41/4 ")

Back View:

t

972 mm

{381/4'')

279 mm

,", IT

t

i

359 mm

(141/8"}

100 mm

(4"}

Recessed Area and Closet Installation

This dryer may be installed in a recessed area or closet. If

a closet door or Iouvered door is installed, the minimum

unobstructed air openings in the top and bottom of the door are

required. For recessed area and closet installations, minimum

clearances can be found on the serial tag on the dryer.

356 mm _----_1

(14"} max [........ !.....

r- ........ j .....

102mm I_%'.....

(4"} \ ""%.

f (1")

mm

"}

J

,..25mm

(1"}

76

(:

76

5 ram1

[] Dimensions shown are minimum spacings required. Consider

allowing more space for ease of installation, servicing, and

compliance with local codes and ordinances.

[] Additional spacing for companion appliances and clearances

for walls, doors, and floor moldings should also be

considered. Add spacing of 25 mm (1") on all sides of dryer

to reduce noise transfer.

[] This dryer must not be installed behind a Iockable door,

a sliding door or a door with a hinge on the opposite side

to that of the dryer.

[] The dryer must be exhausted outdoors.

[] No other fuel-burning appliance may be installed in the same

closet as the dryer.

ELECTRICAL REQUIREMENTS

ENectricaNShock Hazard

ENectrically ground this appliance.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

This dryer is supplied without an electric cord and plug.

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with all local codes and ordinances.

[] To supply the required single phase, 240 volt, 60 Hz, AC

only electrical supply on a separate 30-amp circuit fused on

both sides of the line. A time-delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit. Do

not have a fuse in the neutral or grounding circuit.

[] Do not use an extension cord.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly installyour dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

if using a power supply cord:

[] If the supply cord is damaged, it must be replaced by the

manufacturer, a qualified service agent, or other qualified

person to avoid a hazard.

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

[] A UL listed 30-amp power supply cord, rated 240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

[] A UL listed strain relief.

Connecting by direct wire:

Power supply cable must match power supply and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with flexible metallic conduit. All

current-carrying wires must be insulated.

[] 10-gauge solid copper wire (do not use aluminum).

[] At least 5 ft (1.52 m) long.

[] Disconnection must be incorporated in the fixed wiring in

accordance to the wiring rules for your region.

Recommended Grounding Method

[] It is your responsibility to contact a qualified electrical installer

to ensure that the electrical installation is adequate and in

conformance with all local codes and ordinances.

GROUNDING INSTRUCTIONS

m=For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

INSTALL LEVELING LEGS

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. Prepare dryer for leveling legs

To avoid damaging floor, use a large flat piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

6

2, Screw in leveling legs

diamond

marking

Examine leveling legs, find diamond marking. Screw legs into

leg holes by hand, use a wrench to finish turning legs until

diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is

close to its final location. Leave enough room for electrical

connection and to connect the exhaust vent.

VENTING REQUIREMENTS

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent,

Failure to follow these instructions can result in death

or fire,

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or flexible metal vent shall be used for

exhausting.

(4")

[] Only a 102 mm (4") heavy metal exhaust vent and clamps

may be used. Do not install metal vent that is smaller than

102 mm (4")in diameter.

[] Do not use plastic, non-metal, or metal foil vent.

Rigid metal vent

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess flexible metal vent to avoid sagging

and kinking that may result in reduced airflow and poor

performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 2.4 m (73Aft.).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or flexible metal vents. Review "Vent System Chart" and

if necessary, modify existing vent system to achieve best drying

performance.

Exhaust hoods:

[] Must be at least 305 mm (12")from ground or any object that

may obstruct exhaust (such asflowers, rocks, bushes, or

snow).

Recommended Styles:

Louvered Hood

Acceptable Style:

Box Hood

Angled Hood

Elbows:

[] 45° elbows provide better airflow than 90° elbows.

Bet

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Vent products can be purchased from your dealer. For more

information, see "Assistance or Service" section in your "Use

and Care Guide."

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

PLAN VENT SYSTEM

The design of the flue system should ensure that any condensate

formed when operating the appliance from cold, is either retained

and subsequently evaporated or discharged. Following these

installation instructions should adequately meet this requirement.

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

A--

B

G

E. Clamps

E Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best

for your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

Over-The-Top installation (also available with one offset elbow)

Periscope installation

If you prefer, dryer may be converted to exhaust out right side,

left side, or through bottom. You must contact your local dealer

to have dryer converted.

Determine vent path:

[] Select route that will provide straightest and most direct

path outdoors.

[] Plan installation to use fewest number of elbows and turns.

[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking.

[] Use as few 90° turns as possible.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Determine vent length and elbows needed for best

drying performance:

[] Use following Vent System Chart to determine type of vent

material and hood combinations acceptable to use.

f

NOTE: Do not use vent runs longer than those specified

in Vent System Chart. Exhaust systems longer than those

specified will:

[] Shorten life of dryer.

[]

Reduce performance, resulting in longer drying times

and increased energy usage.

Number of

90 °turns

or elbows

2

3

4

Vent System Chart

Type

of vent

Rigid metal

Box/Iouvered Angled

hoods hoods

15,8 m (52 ft.) 13,4 m (44 ft.)

13,4 m (44 ft.) 11,0 m (36 ft.)

11,0 m (36 ft.) 18,5 m (28 ft.)

8,2 m (27 ft.) 6,4 m (21 ft.)

6,1 m (20 ft.) 4,3 m (14 ft.

The Vent System Chart provides venting requirements that

will help achieve best drying performance.

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add

one 90° turn to the chart.

8

The maximum length using a 51 mm x 152 mm (2"x 6")

rectangular vent with 2 elbows and a 64 mm (2-1/2") exhaust

hood is 2,4 m (8 ft).

For exhaust systems not covered by the Vent System Chart (such

as multiple unit hookups, plenums, and power-assist fans), see

Service Manual. (To purchase the Service Manual, contact your

local authorized service dealer.)

INSTALLVENT SYSTEM

1, Install exhaust hood

305 rnm

(12"rain,)

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

, Connect vent to exhaust hood

I

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 102 mm (4") clamp. Run vent to dryer location

using straightest path possible. Avoid 90° turns. Use clamps

to seal all joints. Do not use duct tape, screws, or other

fastening devices that extend into interior of vent to secure

vent, because they can catch lint.

CONNECT VENT

Using a 102 mm (4") clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 102 mm (4") clamp.

2, Move dryer to final location

Move dryer to final location. Avoid crushing or kinking vent.

After dryer is in place, remove corner posts and cardboard

from under the dryer.

LEVEL DRYER

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1, Level Dryer

Check levelness of dryer from side to side. Repeat from

front to back.

NOTE: The dryer must be level to reduce noise and assure

proper performance.

If legs are not long enough to level dryer, order Extended Dryer

Feet kit (sold two legs per kit), from your dealer.

Not Level LEVEL Not Level

2, Tighten and adjust leveling legs

If dryer is not level, prop up using a wood block, use wrench

to adjust legs up or down, and check again for levelness.

Once legs are level, make sure all four legs are snug against

the ground.

COMPLETE INSTALLATION

CHECKLIST

[_ Check that all parts are now installed. Ifthere is an extra

part, go back through steps to see what was skipped.

[_ Check that you have all of your tools.

[_ Dispose of/recycle all packaging materials.

[_ Check dryer's final location. Be sure vent is not crushed

or kinked.

[_ For power supply cord installation, plug into an outlet.

For direct wire installation, turn on power.

[_ Check that dryer is level. See "Level Dryer".

[_ Remove film on console and any tape remaining on dryer.

[_ Wipe dryer drum interior thoroughly with a damp cloth

to remove any dust.

[_ Read "Dryer Use" in your "Use and Care Guide."

[_ Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer.

If the dryer will not start, check the following:

[] Controls are set in a running or "On" position.

[] Start button has been pushed firmly.

[] Dryer is plugged into an outlet and/or electrical supply

is on.

[] Household fuse is intact and tight, or circuit breaker has

not tripped.

[] Dryer door is closed.

[_ When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off dryer, and check the

following:

[] There may be 2 household fuses or circuit breakers for

the dryer. Check that both fuses are intact and tight,

or that both circuit breakers have not tripped. If there

is still no heat, contact a qualified technician.

NOTE: You may notice an odor when the dryer is first heated.

This odor is common when the heating element is first used.

The odor will go away.

10

REVERSE DOOR SWING (OPTIONAL)

(MODELS WITH SIDE SWINGS DOORS ONLY)

27" Wide Model Side-Swing Door

1, Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

Remove bottom screws

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Lift door off top screws

4, Remove screws from hinges

Remove screws attaching hinges to door.

5. Remove screws from door

\

Remove screws at top, bottom, and side of door (6 screws).

Keep door screws separate from hinge screws as they are

different sizes. Holding door over towel on dryer, grasp sides

of outer door and lift to separate it from inner door.

NOTE: Do not pry apart with putty knife or screwdriver.

Do not pull on door seal or plastic door catches.

6, Rotate outer door

Rotate outer door 180° and set it back down on inner door.

Be certain to keep cardboard spacer centered between

doors. Reattach outer door panel to inner door panel so

handle is on the side where hinges were just removed. Insert

6 door screws.

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

11

7, Flip door over

Flip door over so handle side is down.

8, Attach door hinges

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

dryer cabinet

NOTE: 2 people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer

cabinet. Tighten screws halfway. Position door so large end of

door hinge slot is over screws. Slide door up so screws are in

bottom of slots. Tighten screws. Insert and tighten top screws

in hinges.

fll, Check door strike alignment

Close door and check that door strike aligns with door catch.

If it is needed, slide door catch left or right within slot to

adjust alignment.

TROUBLESHOOTING

See the "Use and Care Guide" to possibly avoid the cost of a

service call.

Remove the 4 screws that attach 2 plugs on the left side.

Transfer plugs to opposite side using the same 4 screws.

12

Page is loading ...

Amana 4KAED4900BW1 Installation guide

Amana 4KAED4900BW1 Installation guide

in other languages

Related papers

Other documents