Nex 730-0247 Owner's manual

Brand: Nex

Model: 730-0247

Category: Barbecues & grills

Type: Owner's manual

Stainless Steel Gas Grill

USE AND CARE GUIDE

MODEL NO.: 730-0247

100

200

300

400

500

600

700

800

FOR OUTDOOR USE ONLY

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE

DO NOT RETURN TO PLACE OF PURCHASE

TABLE OF CONTENTS

SECTION ONE

Safety Instructions…………………………1~6

Natural Gas Safety……………………………6

SECTION TWO

Installation of Side Shelves .………….…...7

Installation of Push Bar………..……………8

Installation of Dividing Shelf………………..9

Installation of Battery………………………10

Installation of Nature Gas Regulator and

Hose…………………11

Installation of Rotisserie kit………………..12

To Match light the Gill………………………13

SECTION THREE

Leak Testing……………………………….14

Installer Final Check……………………...15

SECTION FOUR

Operating Instructions…………………15~16

Lighting Instructions……………………....17

Read this Care and Use Manual carefully

and completely before using your grill to

reduce the risk of fire, burn hazard or

other injury.

SECTION FIVE

Using the Side Burner……………………

Care & Maintenance ………………….

Care & Maintenance of Side Burner…..

Trouble Shooting…………………………

SECTION SIX

Exploded View……………………………..

Parts List …………………………………..

Grilling Hints………………………………..

Grill Cooking Chart ……………………….

Grill Recipe Suggestion ………………….

27~28

25~26

19~21

SECTION SEVEN

Limited Warranty ………………………….

SAFETY INSTRUCTIONS

***** WARNING *****

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open Lid.

4. If odor continues, immediately call your gas supplier or your

fire de

artment.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids

in the vicinity of this or any other appliance.

SAFETY INSTRUCTIONS

WARNING

Do not try lighting this appliance without first

reading the “LIGHTING INSTRUCTIONS”

section of this manual.

DO NOT USE ALUMINUM FOIL TO LINE THE GRILL

RACKS OR GRILL BOTTOM. This can severely

upset combustion airflow or trap excessive heat in

the control area.

INSECT WARNING!!! Spiders and insects can

nest in the burners of this and any other grill,

and cause the gas to flow improperly. This is a

very dangerous condition, which can cause a

fire to occur behind and beneath the valve

panel, thereby damaging the grill and making

it unsafe to operate. Inspect the grill twice a

year.

WARNING

ELECTRICAL GROUNDING

INSTRUCTIONS

This appliance (rotisserie motor) is

equipped with a plug and should be

plugged directly into a properly

grounded receptacle. DO NOT cut or

remove the grounding prong from this

plug.

Keep the rotisserie motor electric cord

away from the heated surfaces of the

grill. When not in use remove and store

the motor in a dry location

DO NOT LEAVE THE GRILL

UNATTENDED WHILE COOKING.

CAUTION: REMOVE THE

WARMING RACK WHEN USING

THE ROTISSERIE BURNER. THE

HIGH HEAT COMING FROM THE

BURNER MAY CAUSE THE

WARMING RACK TO BEND.

SAFETY INSTRUCTIONS

WARNING: Always keep your face and body as far away from the

burner as possible when lighting.

WARNING: IMPORTANT!

BEFORE LIGHTING…

Inspect the gas supply hose prior to turning the gas “ON”. If there is

evidence of cuts, wear, or abrasion, it must be replaced prior to use. Do

not use the grill if the odor of gas is present. Only the pressure regulator

and hose assembly supplied with the unit should be used. Never

substitute regulators for those supplied with the grill. If a replacement is

necessary, contact the factory for proper replacement.

Keep a spray bottle of soapy water near

the gas supply valve and check the

connections before each use.

Do not attempt to light the grill if odor of

gas is present. Call for service

1-800-913-8999.

ROTISSERIE DRIVE MOTOR

USE ONLY FOR OUTDOORS, DO NOT EXPOSE TO

RAIN.

CAUTION: TO ENSURE CONTINUED

PROTECTION AGAINST RISK OF ELECTRIC

SHOCK, CONNECT TO PROPERLY GROUNDED

OUTLETS ONLY, TO REDUCE THE RISK OF

ELECTRIC SHOCK, KEEP EXTENSION CORD

CONNECTION DRY AND OFF THE GROUND.

CHILDREN SHOULD NOT BE LEFT ALONE OR

UNATTENDED IN AN AREA WHERE THE GRILL

IS BEING USED. NEVER ALLOW THEM TO SIT,

STAND OR PLAY ON OR AROUND THE GRILL

AT ANY TIME.

DO NOT STORE ITEMS OF INTEREST TO

CHILDREN AROUND OR BELOW THE GRILL

OR IN THE CART. NEVER ALLOW CHILDREN

TO CRAWL INSIDE OF THE CART.

Never let clothing, pot holders or other

flammable materials come in contact with or

too close to any grate, burner or hot surface

until it has cooled. Fabric may ignite and result

in personal injury.

For personal safety, wear proper apparel.

Loose fitting garments or sleeves should

never be worn while using this appliance.

Some synthetic fabrics are highly flammable

and should not be worn while cooking.

Only certain types of glass, heatproof glass

ceramic, earthenware, or other glazed utensils

are suitable for grill use. Theses types of

materials may break with sudden temperature

changes. Use only on low or medium heat

settings according to the manufacturer’s

directions.

Do not heat unopened food containers as a

build-up of pressure may cause the container

to burst.

Use a covered hand when opening the grill lid.

Never lean over an open grill.

WHEN LIGHTING A BURNER, ALWAYS PAY

CLOSE ATTENTION TO WHAT YOU ARE

DOING. BE CERTAIN YOU ARE TURNING THE

IGNITER LABELED FOR THE BURNER YOU

INTEND ON USING.

SAFETY INSTRUCTIONS

TESTED IN ACCORDANCE WITH ANSI

Z21.58b-2002/CGA 1.6b-2002 STANDARD FOR

OUTDOOR COOKING GAS APPLIANCES. THIS

GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the proper

method of installation. In the absence of local

codes, this unit should be installed in accordance

with the National Fuel Gas Code No. Z223.1-1988

and the National Electrical Code ANSI/NFPA No.

70-1990.

CALIFORNIA PROPOSITION

65-WARNING

The burning of gas fuel generates some

byproducts, which are on the list of

substances, which are known by the State of

California to cause cancer or reproductive

harm. California law requires businesses to

warn customers of potential exposure to such

substances. To minimize exposure to these

substances, always operate this unit according

to the use and care manual, ensuring you

provide good ventilation when cooking with

gas.

When properly cared for, your grill will give safe,

reliable service for many years. However,

extreme care must be used since the grill

produces intense heat and that can increase

accident potential. When using this appliance

basic safety practices must be followed,

including the following:

Do not repair or replace any part of the grill

unless specifically recommended in this

manual. All other service should be referred to a

qualified technician.

SAFETY PRACTICES TO AVOID PERSONAL INJURY

SAFETY INSTRUCTIONS

When using the grill, do not touch the grill rack,

burner grate or immediate surroundings as

these areas become extremely hot and could

cause burns. Use only dry potholders. Moist or

damp potholders on hot surfaces may cause

burns from steam. Do not use a towel or bulky

cloth in place of potholders. Do not let

potholders touch hot portions of the grill rack.

cleaner on or around the grill. The chemical that

produces the spraying action could, in the

presence of heat, ignite or cause metal parts to

corrode.

Do not use the grill for cooking excessively fatty

meats or products, which promote flare-ups. Do not

operate the grill under unprotected

Grease is flammable. Let hot grease cool

before attempting to handle it. Avoid letting

excess grease deposits collect in the grease

tray at the bottom of the grill’s firebox. Clean

often.

For proper lighting and performance of the

burners keep the burner ports clean. It is

necessary to clean them periodically for

optimum performance. The burners will only

operate in one position and must be mounted

correctly for safe operation.

Clean the grill with caution. Avoid steam burns;

do not use a wet sponge or cloth to clean the

grill while it is hot. Some cleaners produce

noxious fumes or can ignite if applied to a hot

surface.

Be sure all grill controls are turned off and the

grill is cool before using any type of aerosol

combustible construction. Use only in well

ventilated areas. Do not use in buildings,

garages, sheds, breezeways or other such

enclosed areas. THIS UNIT IS FOR OUTDOOR

USE ONLY.

Keep the area surrounding the grill free from

combustible materials, trash, or combustible

fluids and vapors such as gasoline or charcoal

lighter fluid. Do not obstruct the flow of

combustion and ventilation air. If the unit is

stored indoors ensure that it is cool.

Keep the back of the cart free and clear from

debris. Keep any electrical supply cord, or the

rotisserie motor cord away from the heated

areas of the grill.

Never use the grill in extremely windy

conditions. If located in a consistently windy

area (oceanfront, mountaintop, etc.) a

windbreak will be required (see below). Always

adhere to the specified clearance.

SAFETY INSTRUCTIONS

3. Apply the soap solution to all gas

connections. Bubbles will appear in the

soap solution if connections are not

properly sealed. Tighten or repair as

necessary.

CHECKING FOR GAS LEAKS

Never test for leaks with a flame. Prior to

first use and at the beginning of each new

season, you must check for gas leaks.

FOLLOW THESE STEPS:

1.Make soap solution by mixing one part

liquid detergent and one part water.

2.Turn off heat control valves, and then

turn on gas at source.

4. If you have a gas leak that you cannot

repair, turn off the gas at the source,

disconnect the fuel line from grill and

immediately call your grill dealer or gas

supplier for professional assistance.

NATURAL GAS SAFETY

Your natural gas grill is designed to operate

on natural gas grill only, at a pressure of

water column (W.C.) 4” water column

residential (1/4 psig or 1.75 kpa) regulated at

the residential meter. Check with your gas

utility for local gas pressure and with your

local municipality for building code

requirements. If your residential gas utility

line pressure has not been regulated to 7”

W.C. contact your local gas utility or gas grill

dealer for professional assistance.

gas line piping enters the ground indoors in

an accessible location near the supply line.

Pipe sealing compound or pipe thread tape

of the type resistant to the action of natural

gas must be used on all male pipe threads

when making the connection.

Disconnect your gas grill from its fuel

source when the gas supply lines are being

tested at high pressures by the gas

company. This appliance and its individual

shut off valve must be disconnected from

the gas supply piping system during any

pressure testing of that system at pressure

in excess of ½ psi (3.5 kpa).

Check with your gas utility or with local

building codes for instructions to install gas

supply line, or call a licensed and

knowledgeable installer.

Turn off your gas grill when the gas supply

is being tested at low pressures by the gas

company. This appliance must be isolated

from the gas supply piping system by

closing its individual manual shut off valve

during any pressure testing of the gas

supply piping system at pressures equal or

less than ½ psi (3.5kpa)

It is recommended that an “ON-OFF” shut off

valve be installed at the gas supply source;

outdoors after the gas line piping exits

outside the wall and before the

quick-disconnect. In a branch fuel line, it

should be installed before the

INSTALLATION OF SIDE SHELVES

The screws used to attached the side shelves are already screwed into the two side

panels of the grill.

Remove the screws from the side panel and align with the holes in the left side panel.

Then install the left shelf as shown in the figure below.

Repeat the above step to install the right shelf on right side panel.

INSTALLATION OF PUSH BAR

The screws used to attach the push bar are already screwed into the two shelves.

Remove the screws from the two side shelves, align with the holes in the push bar, and

then re-screw into the holes on the two shelves of the grill. Press the cap against the

ends of the push bar, and gently tap them into place..

800

700

600

500

400

300

200

100

INSTALLATION OF SPICE TRAY AND DIVIDING SHELF

Put the spice tray into the hook on the right door.

Place the spice tray inside the right door. Assembly steps as shown in the figure below.

Place the dividing shelf inside the right door.

800

700

600

500

400

300

200

100

INSTALLATION OF BATTERY

In order to install the battery, remove the ignition button housing. Repeat the ignition

button housing after battery is installed. Please keep the positive pole facing toward

you. Tight the ignition button after installed the battery.

800

700

600

500

400

300

200

100

INSTALLATION OF NATURE GAS REGULATOR AND HOSE

The Nature Gas regulator has been factory installed. Attach the PVC Gas Hose to

the regulator (See drawing below).

Connect the other end of the PVC Gas Hose to the house gas line using the

quick-connect fitting.

800

700

600

500

400

300

200

100

INSTALLATION OF ROTISSERIE KIT

The screws for rotisserie mount are already screwed into the rotisserie kit. After install

the rotisserie motor mount, Assemble the rotisserie skewer as shown in the figure

below.

TO MATCH LIGHT THE GRILL

If the burner will not light after several attempts then the burner can be match lit.

If you’ve just attempted to light the burner with the ignition, allow 5 minutes for any

accumulated gas to dissipate. Keep your face and hands as far away from the grill as

possible. Insert a lit extended match or lighter through the cooking grids to the burner.

Press the control knob and rotate left to the HI setting, continue to press the knob until

the burner ignites. Burner should light immediately. If the burner does not light in 4

seconds turn the knob off, wait 5 minutes and try again.

LEAK TESTING

to shipment; however, variations in the local gas

supply may make it necessary to adjust the

burners, the flames of the burners should be

visually checked.

GENERAL

Although all gas connections on the grill are leak

tested at the factory prior to shipment, a complete

gas tightness check must be performed at the

installation site due to possible mishandling in

shipment, or excessive pressure unknowingly

being applied to the unit. Periodically check the

whole system for leaks following the procedures

listed below. If the smell of gas is detected at

anytime you should immediately check the entire

system for leaks

BEFORE TESTING

ustment Bolt

Lockin

Nut

Flames should be blue and stable with no yellow

tips, excessive noise or lifting. If any of these

conditions exist, check to see if the air shutter or

burner ports are blocked by dirt, debris, spider

webs, etc. If you have any questions regarding

flame stability, please call customer service at

1-800-913-8999.

Make sure that all packing material is removed from

the grill including the burner tie-down straps.

DO NOT SMOKE WHILE LEAK TESTING.

NEVER LEAK TEST WITH AN OPEN FLAME.

Make a soap solution of one part liquid detergent

and one part water. You will need a spray bottle,

brush, or rag to apply the solution to the fittings. For

the initial leak test, make sure the L.P. cylinder is

full.

TO TEST

Make sure all control valves are in the “OFF”

position. Turn the gas supply on. Check all

connections from the L.P. cylinder up to and

including the connection to the manifold pipe

assembly (the pipe that goes to the burners). Soap

bubbles will appear where a leak is present. If a leak

is present, immediately turn off the gas supply,

tighten any leaking fittings, turn gas on, and

recheck. Should the gas continue to leak from any

or all of the fittings, turn off the gas supply, and

contact our customer service at 1-800-913-8999.

Only those parts recommended by the

manufacturer should be used on the grill.

Substitution will void the warranty. Do not use the

grill until all connections have been checked and do

not leak.

GAS FLOW CHECK:

Each grill burner is tested and adjusted at the

factory prior

ALWAYS CHECK FOR LEAKS AFTER EVERY LP

TANK CHANGE

Check all gas supply fittings for leaks before each

use. It is handy to keep a spray bottle of soapy

water near the shut-off valve of the gas supply line.

Spray all the fittings. Bubbles indicate leaks.

Disconnected L.P. cylinders must have threaded

valve plugs tightly installed, and must not be stored

in a building, garage or any other enclosed area.

The gas must be turned off at the supply cylinder

when the unit is not in use.

If the appliance is stored indoors the cylinder must

be disconnected and removed from the appliance.

Cylinders must be stored outdoors in a

well-ventilated area out of the reach of children.

INSTALLER FINAL CHECK

 Specified clearance maintained 24” from

combustibles.

 All internal packaging removed.

 Knobs turn freely.

 Burners are tight and sitting properly on

orifices.

 Pressure regulator connected and set for

11.2” W.C. LP gas. Gas connections to grill

using hose & regulator assembly provided

(pre-set for 11.0” water column).

 Unit tested and free of leaks.

 User informed of gas supply shut off valve

location.

PLEASE RETAIN THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

OPERATING INSTRUCTIONS

General use of the grill and rotisserie

Each main burner is rated at 12,000 BTU/hr. The

main grill burners encompass the entire cooking

area and are side ported to minimize blockage from

falling grease and debris. Above the burners are

stainless steel radiant (flame tamers). The igniter

knobs are located on the lower center portion of the

valve panel. Each rotary igniter is labeled on the

control panel.

To begin:

1. Make sure the grill has been leak tested and is

properly located.

2. Remove any remaining packing material.

3. Light the grill burners using the instructions on

page 13.

4. Turn the control knob(s) to “HI” and preheat the

grill for 15 minutes. The grill lid is to be closed

during the appliance preheat period.

5. Place the food on the grill and cook to the

desired doneness. Adjust heat setting, if

necessary. The control knob may be set to any

position between “HI” and “LO”

USING THE GRILL:

Grilling requires high heat for searing and proper

browning. Most foods are cooked at the “HI” heat

setting for the entire cooking time. However, when

grilling large pieces of meat or poultry, it may be

necessary to turn the heat to a lower setting after

the initial browning. This cooks the food through

without burning the outside. Foods cooked for a

long time or foods basted with a sugary marinade

may need a lower heat setting near the end of the

cooking time.

NOTE: The grill is designed to grill efficiently

without the use of lava rocks or briquettes of any

kind. Heat is radiated by the stainless steel flame

tamers positioned above each burner.

NOTE: The hot grill sears the food, sealing in the

juices. The longer the preheat, the faster the meat

browns and the darker the grill marks.

OPERATING INSTRUCTIONS

USING

ROTISSERIE

BURNER

Your grill is capable of performing back burner

rotisserie cooking. Light the rear burner as

described in the lighting instructions, once lit, the

rotisserie burner will reach cooking temperatures in

about 1 minute.

The rotisserie motor is capable of turning up to a

12lb. cut of meat or poultry. The motor slides onto

the stainless steel motor mount. The rotisserie

motor must be electrically grounded in accordance

with local codes or, in the absence of local codes,

with the National Electrical Code,

ANSI/NFPA 70-1990.

DO NOT LEAVE THE GRILL UNATTENDED WHILE

COOKING.

The skewers for the rotisserie are assembled into

the motor assembly by placing the pointed end into

the motor, and then sliding the grooved bushing

into the slot at the opposite side of the grill. The

thumbscrew for the grooved bushing should be

inside the grill body. To load the skewer, begin with

the bushing screwed on the skewer rod at the

opposite end from the point. Slide the counter

balance apparatus and tighten on the skewer rod

approximately 2-4” from the bushing. Slide the first

meat fork onto the skewer rod prongs toward the

food. Center the product to be cooked on the

skewer then push the meat forks firmly together.

Tighten the wing nuts as tight as possible.

It may also be necessary to wrap the food with

butchers string (never use nylon or plastic string) to

secure any loose portions. Once the food is secure

insert the skewer into the motor. It is normal for the

skewer to flex when larger cuts of meat are being

cooked. It may also be necessary to remove the

cooking grids for larger cuts of meat. If the meat

scrapes on the cooking grids during any part of the

rotation, the grids must be removed. Adjust the

counter balance weight to balance the heavier side

of the meat and avoid lopsided rotation of the

rotisserie motor.

After your first use of the rotisserie burner it is likely

that the stainless steel adjacent to the burner will

darken to a dark blue color. This is a normal

property of the non-rusting, type 304 stainless steel

used on the grill.

WARNING

ELECTRICAL GROUNDING INSTRUCTIONS

This appliance (rotisserie motor) is equipped with a

plug and should be plugged directly into a properly

grounded receptacle. DO NOT cut or remove the

grounding prong from this plug.

Keep the rotisserie motor electric cord away

from the heated surfaces of the grill. When not

in use remove and store the motor in a dry

location

CAUTION: REMOVE THE WARMING RACK

WHEN USING THE ROTISSERIE BURNER. THE

HIGH HEAT COMING FROM THE BURNER MAY

CAUSE THE WARMING RACK TO BEND.

LIGHTING INSTRUCTIONS

Do not attempt to light the grill if odor of gas is

present. Call for service 1-800-913-8999.

WARNING: IMPORTANT!

BEFORE LIGHTING…

Inspect the gas supply hose prior to turning the

gas “ON”. If there is evidence of cuts, wear, or

abrasion, it must be replaced prior to use. Do not

use the grill if the odor of gas is present. Only the

pressure regulator and hose assembly supplied

with the unit should be used. Never substitute

regulators for those supplied with the grill. If a

replacement is necessary, contact the factory for

proper replacement.

Screw the regulator (type QCC1) onto the tank.

Leak check the hose and regulator connections

with a soap and water solution before operating

the grill

TO LIGHT THE GRILL BURNER:

Make sure all knobs are “OFF” then turn on the

gas supply from the LP tank. Always keep your

face and body as far from the grill as possible

when lighting.

Your grill has an exclusive patented built-in

ignition. The igniter is built in to the valve. To

ignite each burner simply push and turn the

control knobs to the HI setting, you will hear the

valve click as it sends a spark to the pilot flame. If

the burner does not light, wait 5 minutes for any

excess gas to dissipate and then retry.

FLAME CHARACTERISTICS

Check for proper burner flame characteristics.

Each burner is adjusted prior to shipment;

however, variations in the local gas supply may

take minor adjustments necessary.

Burner flames should be blue and stable with no

yellow tips, excessive noise, or lifting. If any of

these conditions exist call our customer service

line. If the flame is yellow, it indicates insufficient

air. If the flame is noisy and tends to lift away from

the burner, it indicates too much air.

TO MATCH LIGHT THE GRILL:

If the burner will not light after several attempts

then the burner can be match lit.

If you’ve just attempted to light the burner with the

igniter, allow 5 minutes for any accumulated gas

to dissipate. Keep your face and hands as far

away from the grill as possible. Insert a lit

extended match or lighter through the cooking

grids to the burner. Press the control knob and

rotate left to the HI setting, continue to press the

knob until the burner ignites. Burner should light

immediately. If the burner does not light in 4

seconds turn the knob off, wait 5 minutes and try

again.

TO LIGHT THE ROTISSERIE BURNER:

Open the lid; push the knob for about 5 seconds

without rotating. This will allow time for the gas to

flow into the rear burner. Continue pushing for 5

seconds then turn the knob to the HI position,

then press the igniter button to light the rotisserie

burner. If the burner does not light, turn the

control knob to “OFF”. If the igniter does not

function, follow the instruction above for match

lighting.

Keep a spray bottle of soapy water near the

gas supply valve and check the connections

before each use.

USING THE SIDE BURNER

WARNING: IMPORTANT!

USING THE SIDE BURNER:

Inspect the gas supply hose prior to turning the

gas “ON”. If there is evidence of cuts, wear or

abrasion, it must be replaced prior to use. Do not

use the side burner if the odor of gas is present.

WARNING: Always keep your face and body

as far away from the burner as possible when

lighting.

LIGHT INSTRUCTION

To light the side burner, remove any cooking

utensils from the burner grate. Push and turn the

control knob counterclockwise to the “HI” position. If

the burner does not light, turn the control knob to

“OFF”. If the smell of gas is detected and the igniter

is not functioning, immediately turn the control knob

“OFF”. Allow 5 minutes for any accumulated gas to

dissipate. If the side burner igniter is not functioning,

see the following section for match lighting.

MATCH LIGHTING

Hold a lit extended match or lighter near the side

burner ports, turn the control knob counterclockwise

to “HI”. Move your hand immediately once the

burner is lit. Rotate the control knob to the desired

setting.

CARE & MAINTENCACE

STAINLESS STEEL

The grill is made from non-rusting and non-magnetic

stainless steel. There are many different stainless

steel cleaners available. Always use the mildest

cleaning procedure first, scrubbing in the direction of

the grain. To touch up noticeable scratches in the

stainless steel, sand very lightly with dry 100 grit

emery paper in the direction of the grain. Specks of

grease can gather on the surfaces of the stainless

steel and bake on to the surface and give the

appearance of rust. For removal use an abrasive pad

in conjunction with a stainless steel cleaner.

GRILL RACK

The easiest way to clean the grill is immediately after

cooking is completed and after turning off the flame.

Wear a barbeque mitt to protect your hand from the

heat and steam. Dip a brass bristle barbeque brush in

tap water and scrub the hot grill. Dip the brush

frequently in the bowl of water. Steam, created as

water contacts the hot grill, assists the cleaning

process by softening any food particles. The food

particles will fall and burn. If the grill is allowed to cool

before cleaning, cleaning will be more difficult.

ENSURE THAT THE GAS SUPPLY AND THE KNOBS

ARE IN THE “OFF” POSITION. MAKE

SURE THE RANGETOP BURNER IS COOL BEFORE

REMOVAL.

GRILL BURNERS

Extreme care should be taken when moving a burner

as it must be correctly centered on the orifice before

any attempt is made to relight the grill. Frequency of

cleaning will depend on how often you use the grill.

GRILL BURNER CLEANING

Ensure the gas supply is off and the knobs are in the

“OFF” position. Make sure the grill is cool. Clean the

exterior of the burner with a wire brush. Clear

stubborn scale with a metal scraper. Clear any

clogged ports with a straightened paper clip. Never

use a wooden toothpick as it may break off and clog

the port. Please note if insects or other obstructions

are blocking the flow of gas through the burner, and if

so you will need to call our customer service line:

1-800-913-8999.

GREASE TRAY CLEANING

The grease tray should be emptied and wiped down

periodically and washed in a mild detergent and warm

water solution. A small amount of sand or cat litter

may be placed in bottom of grease tray to absorb the

grease. Check the grease tray frequently, don’t allow

excess grease to accumulate and overflow out of the

grease tray.

Page is loading ...

Nex 730-0247 Owner's manual

Brand: Nex

Model: 730-0247

Category: Barbecues & grills

Type: Owner's manual

Download PDF

report

Nex 730-0247 Owner's manual

Nex 730-0247 Owner's manual

Related papers

Other documents