StarTech.com S2510SM12U33 User manual

Brand: StarTech.com

Model: S2510SM12U33

Category: HDD/SSD enclosures

Type: User manual

StarTech.com S2510SM12U33 is a USB 3.0 to 2.5in SATA Hard Drive Enclosure with UASP. It allows you to connect a 2.5" SATA hard drive or solid state drive to your computer through a USB 3.0 port. The enclosure supports USB 3.0 data transfer rates of up to 5 Gbps, and is also backward compatible with USB 2.0 ports. The enclosure features a built-in LED indicator that lets you monitor drive activity. It also has a power jack for connecting an optional power adapter, in case the USB port does not provide enough power. The enclosure comes with a USB 3.0 cable, a screw kit, and a set of foot pads.

Manual Revision: 01/30/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

S2510SM12U33

USB 3.0 to 2.5in SATA Hard Drive Enclosure

with UASP

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Product Diagram ....................................................................................1

Introduction ............................................................................................ 2

Packaging Contents ................................................................................................................................. 2

System Requirements ..............................................................................................................................2

Installation ..............................................................................................3

Hardware Installation ..............................................................................................................................3

How to Use ..............................................................................................6

Connecting the Hard Drive .................................................................................................................... 6

Powering the Drive Enclosure .............................................................................................................. 6

LED Indicator .............................................................................................................................................. 7

Disconnecting the Hard Drive .............................................................................................................. 7

Initializing the Hard Drive ...................................................................................................................... 8

Specications .......................................................................................... 9

Technical Support ..................................................................................10

Warranty Information ............................................................................ 10

Instruction Manual

Product Diagram

USB 3.0 Type B port

Power Jack (Power

adapter not included)

Power/Activity LED

Instruction Manual

Introduction

Packaging Contents

• 1 x USB 3.0 SATA HDD Enclosure

• 1 x USB 3.0 Cable

• 1 x Screw kit

• 1 x foot pad set

• 1 x Instruction Manual

System Requirements

• Computer system with available USB 3.0 (5 Gbit/s) port or USB 2.0 port (480Mbps)

• 2.5” SATA hard drive or solid state drive

• Microsoft® Windows® 2000/XP/Server 2003/Vista/Server 2008 R2/7/8 (32/64-bit), or

Apple® Mac® OS 9.x/10, or Linux®

Instruction Manual

2. Remove the HDD tray by sliding it out of the enclosure on either side.

Installation

Hardware Installation

WARNING! Hard drives and storage enclosures require careful handling, especially

when being transported. If you are not careful with your hard disk, lost data may

result. Always handle your hard drive and storage device with caution. Be sure that

you are properly grounded by wearing an anti-static strap when handling computer

components or discharge yourself of any static electricity build-up by touching a large

grounded metal surface (such as the computer case) for several seconds.

1. Remove the four screws from the bottom of the enclosure using a small Phillips

head screw driver (not included).

Instruction Manual

3. Connect the the 2.5” SATA Hard Drive to the SATA connector on the HDD tray.

4. Insert two of the larger screws from the included screw kit, into the mounting holes

on either side of the drive tray to x the hard drive into place.

5. Turn the tray over and insert two of the smaller screws from the included screw kit

into the mounting holes on the bottom of the tray using the Phillips head screw

driver, to x the drive into place.

Instruction Manual

6. Reassemble the enclosure by slide the HDD tray with connected hard drive back

into the enclosure.

Note: Ensure the HDD label is facing upward, and the enclosure is assembled with

the LED on the same side of the drive connector.

7. Reinsert the four screws on the bottom of the enclosure.

Instruction Manual

8. Complete installation by connecting the included USB cable from the USB 3.0 type B

port on the enclosure to an available USB port on the computer system.

Note: The hard drive enclosure has a built-in auxiliary Power Jack that is not required

for standard operation. An additional 5V power source be added in the event your USB

port does not provide sucient power.

How to Use

Connecting the Hard Drive

Once the enclosure has been attached to a computer, and the OS has installed the

necessary software, the drive will be accessible as though it were installed within the

system.

Prior to using the drive, it will need to be formatted according to your operating

system requirements. To format your newly attached hard drive, or create partitions,

please consult the documentation that accompanied your operating system at the

time of purchase.

Powering the Drive Enclosure

The hard drive enclosure requires no external power supply, as it is capable of receiving

enough power from the USB Bus to which it is connected.

Instruction Manual

LED Indicator

The hard drive enclosure oers an LED indicator, to enable you to monitor drive

activity. When the enclosure is powered, the LED will illuminate. While the hard drive

is being accessed, the LED will blink. Do not remove the enclosure from the host

computer while the LED is ashing, as it could damage the drive or the enclosure,

resulting in data loss.

Disconnecting the Hard Drive

Windows

1. Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.

2. Select the storage device from the list that appears.

3. Wait for the message indicating that it is now safe to remove the device.

Note: Removing the connected drive prior to receiving notication that it is safe to

do so, could result in losing or corrupting data stored on the drive. Once the Safe

to Remove Hardware message appears, please disconnect the enclosure from the

computer by removing the USB connection.

Mac OS X

To safely disconnect the attached drive from the host computer, close any windows

listing the contents of the removable drive. Once all windows are closed, click on the

USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.

Allow 5 seconds before physically removing the enclosure/drive from the computer.

Instruction Manual

Initializing the Hard Drive

1. If the SATA Hard Drive is blank it may need to be initialized and formatted before

use. From the main Windows desktop, right-click on “My Computer” (“Computer” in

Vista/ 7 / 8), then select Manage. In the new Computer Management window, select

Disk Management from the left window panel.

2. A dialog window should automatically appear, asking you to initialize the drive.

Depending on the version of Windows, it will give you the option of either creating

an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older

operating systems, while MBR is supported by newer and older operating systems.

3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard

drive capacity to conrm it’s the correct hard drive) and then right-click in the

section that says “Unallocated” and select “New Partition”.

4. Follow the on screen prompts to initialize the drive in the format of your choice.

Instruction Manual

Specications

Host Interface USB 3.0

External Connectors

1 x 15 pin SATA Power female

1 x 7 pin SATA Data male

1 x USB 3.0 Cable

Maximum Data Transfer Rate USB 3.0: 5 Gbit/s

Compatible Operating Systems

Windows 2000/XP/Server 2003/Vista/

Server 2008 R2/7/8 (32/64-bit), Mac OS

9/10, Linux

Instruction Manual

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to

provide industry-leading solutions. If you ever need help with your product, visit

www.startech.com/support and access our comprehensive selection of online tools,

documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials

and workmanship for the periods noted, following the initial date of purchase.

During this period, the products may be returned for repair, or replacement with

equivalent products at our discretion. The warranty covers parts and labor costs only.

StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their

ocers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,

or any pecuniary loss, arising out of or related to the use of the product exceed the

actual price paid for the product. Some states do not allow the exclusion or limitation

of incidental or consequential damages. If such laws apply, the limitations or exclusions

contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From

the latest technology to legacy products — and all the parts that bridge the old and

new — we can help you nd the parts that connect your solutions.

We make it easy to locate the parts, and we quickly deliver them wherever they need

to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to

the products you need in no time.

Visit www.startech.com for complete information on all StarTech.com products and

to access exclusive resources and time-saving tools.

StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology

parts. StarTech.com was founded in 1985 and has operations in the United States,

Canada, the United Kingdom and Taiwan servicing a worldwide market.

StarTech.com S2510SM12U33 User manual

Brand: StarTech.com

Model: S2510SM12U33

Category: HDD/SSD enclosures

Type: User manual

Download PDF

report

StarTech.com S2510SM12U33 User manual

StarTech.com S2510SM12U33 User manual

Related papers

Other documents