SVAT Electronics pmn User manual

Page is loading ...

www.svat.com

IMPORTANT SAFETY PRECAUTIONS

PLEASE READ BEFORE INSTALLING

Congratulations on your purchase of the 2.4GHz Wireless Radio Alarm Clock Monitoring System.

Please read these safety and operating instructions carefully before installing and using this sys-

tem.

• Keep the camera, monitor and AC/DC adapter cords out of reach of children.

• Do not place the camera, monitor and AC/DC adapter cords in a crib or playpen.

• Do not use the camera near water or damp and wet environments, such as a bathtub,

laundry tub, kitchen sink, or wet basements.

• Locate the camera, monitor and AC/DC adapters where there is adequate ventilation.

Do not locate the camera in direct sunlight.

• Do not locate the camera, monitor and AC/DC adapters near heat sources such as heat

registers, radiators, ovens, furnaces or other appliances with high operating temperatures.

• Do not use with extension cords. Use only the AC/DC adapters provided with this system.

***Note: Use of other adapters may damage the units and void your warranty.

• Only plug components into standard household voltage outlets (110V - 240V AC, 50Hz or 60Hz).

• Do not place cords from the AC/DC adapters, camera or monitor where they can be

pinched or stepped on. Protect the cords by keeping them out of the way of children, pets

and routine household traffic. Do not place heavy objects on power cords or cover cords

with rugs or carpet.

• When cleaning, use a DRY, lint-free cloth. Unplug the camera, monitor and AC/DC adapters

before cleaning. NEVER immerse any components in water and do not spray cleaners or

solvents on the units. Doing so may damage the units or cause electrical shock.

• Unplug the AC/DC adapters from the wall outlet when the system is not in use.

• Mishandling, alterations or modifications not approved by the manufacturer will void

the warranty.

CAUTION!

• Connect this unit ONLY to other compatible units. Do not connect it to any other type of

alarm or auxiliary device. Connecting anything else to this unit may damage it or prevent it

from operating properly.

• Do not paint over the camera.

• This system uses public airwaves for wireless operation. The sound and video may be

broadcast to and picked up by other 2.4 GHz receiving devices. Conversations and images

from other rooms near the camera may be broadcast and picked up. To protect your

privacy, always turn the camera off when not in use.

IMPORTANT!

ACCESSORIES- Do not place video monitor or equipment on an unstable cart, stand or table.

The video monitor or equipment may fall causing serious injury to a child or adult, and serious

damage to the equipment. Wall or shelf mounting should follow the manufacturer's instruction,

and should use a mounting kit approved by the manufacturer.

• Video monitor equipment and cart combinations should be moved with care.

• Quick stops, excessive force, and uneven surfaces may cause the equipment and cart

combination to overturn.

VENTILATION- Slots and openings in the cabinet and the back or bottom are provided for

ventilation and to ensure reliable operation of the video monitor or equipment and to protect if

from overheating. These openings must not be blocked or covered. The openings should never

be blocked by placing the video monitor on a bed, sofa, rug, or other similar surface. Video

monitor or equipment receiver should never be placed near or over a radiator or heat register.

Video monitor or equipment receiver should not be placed in a built-in installation such as a

bookcase unless proper ventilation is provided.

www.svat.com

INCLUDED IN THIS SYSTEM:

• 2.4GHz Camera inside an alarm clock 1pc

• 2.4GHz Receiver 1pc

• DC Power for Receiver 1pc

• DC Power for Camera 1pc

• A/V Cable 1pc

PARTS OF THE SYSTEM

1. Receiver Antenna 12. Time set button

2. Video out to TV or VCR 13. Auto-on-off alarm/radio switcher

3. Power adapter input 14. Snooze button

4. Receiver channel select 15. Display

5. Radio volume 16. AM/FM radio selecter

6. Camera channel select 17. Hour change button

7. Radio tuner 18. Minute change button

8. Battery compartment 19. Sleep button

9. FM radio antenna

10. Speaker

11. Alarm set button

1

2

3

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

4

General Installation

INSTALLING THE RECEIVER

1. Connect the video output on the receiver to a video input (yellow) RCA

connection on your TV or VCR.

2. Connect the 12V power adaptor to the receiver.

3. Using the channel selector, select a desired channel and flip it to the “ON”

position. *Only one channel can be in the ON position

INSTALLING THE ALARM CLOCK CAMERA

1. Place the alarm clock camera in an appropriate location, connect it to the

supplied adaptor and plug in the adaptor to your wall outlet.

2. Using the channel selector, select the same channel as chosen on the receiver

and flip it to the “ON” position. *Only one channel can be in the ON position

IN ORDER TO VIEW THE IMAGE ON YOUR TELEVISION OR VCR, IT MUST BE ON THE

APPROPRIATE INPUT (A/V) CHANNEL.

SETTING THE TIME AND ALARM ON THE CLOCK

1. Hold the [TIME] button down and press the [HOUR] and [MINUTE] button until

you reach the correct time.

2. Hold the [ALARM] button down and press the [HOUR] and [MINUTE] button until

you reach the desired alarm time.

3. To activate the alarm, set the [AUTO-ON-OFF] switch to AUTO.

Sliding the switch to the ON position will turn the radio on.

www.svat.com

TROUBLESHOOTING

You should...

1. Check that the power cord(s) is properly connected.

2. Check that the monitor is turned ON.

3. Wrong AC/DC adapter used. Check that the adapter

labeled OUTPUT: 10.2V ACx2 is connected to the clock cam-

era, and adaptor labled OUTPUT: 12V DC is connected to the

receiver.

1. Check the channel switch settings on the camera and

receiver. Make sure the channels match on both units.

2. Signal interference from a microwave oven. Check if a

micro-wave oven is in use or located in the path between the

camera and monitor. If so, turn it off or move it out of the

path.

3. Signal interference from other signal producing devices.

(a) Identify and eliminate the source of the interference.

(b) Relocate the camera and/or monitor closer to each other.

(c) Change the channel setting on both camera and receiver.

4. Camera and receiver are too far apart. Relocate the

camera and/or receiver.

If the Camera

and/or Monitor

No Power

No picture.

Distorted picture

Receiver:

Video Out ......................1 Vp-o 75 Ohm

Audio Out ......................1 Vp-o 600 Ohm

Power Supply..................10V DC, 600mA

Operating Temp ............32

o

F - 122

o

F (0-50

o

C)

Dimensions......................3.7” x 1.8” x 2.5”

Weight ............................0.5lb (210 g)

Clock Radio Camera:

Image Sensor..................1/3” CMOS Image Sensor

Resolution........................330 TV lines (H)

Lens..................................6mm

Power Supply..................10.2V DC x 2, 250 mA

DC Backup Power ........DC 9V battery (not included)

Frequency ......................AM 530-1600 KHz

FM 88 - 108 MHz

Operating Temp ............32

o

F - 122

o

F (0-50

o

C)

Dimensions......................2.1” x 1.6” x 6.2”

Weight ............................0.2lb (100 g)

Antenna ..........................FM with 1m wire antenna

AM with built-in ferrite bar antenna

Speaker ..........................1/4” 8 Ohm Dynamic Loudspeaker

Product Specifications

NOTES

_______________________________________________________________________________________________________

www.svat.com

PRODUCT WARRANTY

We take quality very seriously. This is why all of our products

come with a one year warranty from the original purchase date

against defects in workmanship and materials.

If you have warranty or support issues please contact us using any of the following methods:

SVAT Electronics USA SVAT Electronics Canada Phone: 866.946.7828

2315 Whirlpool St., Unit 333 4080 Montrose Road Fax: 888.771.1701

NIagara Falls, New York Niagara Falls, ON Email: [email protected]

USA 14305 Canada L2H 1J9 Website: www.svat.com

Warranty Terms

1. SVAT products are guaranteed for a period of one year from the date of purchase against defects in

workmanship and materials. This warranty is limited to the repair, replacement or refund of the purchase price

at SVAT's option.

2. When service is required, the warranty is validated by the submission of a fully completed warranty card.

3. This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered

with contrary to the applicable instruction manual.

4. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this

warranty.

5. The warranty expressly provided for herein is the sole warranty provided in connection with the product itself

and no other warranty, expressed or implied is provided. SVAT assumes no responsibilities for any other

claims not specifically mentioned in this warranty.

6. This warranty does not cover the shipping cost, insurance or any other incidental charges.

7. You MUST call SVAT before sending any product back for repair. You will be given a Return Authorization

number. When returning the product for warranty service, please pack it carefully in the original box with all

supplied accessories, and enclose your original receipt or copy, and a brief explanation of the problem

(include RA #).

8. This warranty is valid only in Canada and the U.S.A.

9. This warranty card cannot be re-issued.

CAUTION

RISK OF ELECTRIC SHOCK, DO NOT OPEN

Graphic Symbol Explanation:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

Disclaimer: SVAT does not endorse of any of SVAT products for any illegal activites.

SVAT is not responsible or liable in any way shape or form for any damage, vandalism,

theft or any other action that may occur while a SVAT product is in use by the purchaser.

Page is loading ...

SVAT Electronics pmn User manual

This manual is also suitable for

SVAT Electronics pmn User manual

in other languages

Related papers

Other documents