Desa td126 Owner's manual

Propane/LP Patio Heater

Owner’s Manual

MODELS

TD125, TD126, TD127 AND TD128

Save this manual for future reference.

For more information, visit www.desatech.com

IMPORTANT: Read and understand this manual before

assembling, starting or servicing heater. Improper use

of heater can cause serious injury. Keep this manual for

future reference.

WARNING: For

outdoor use only.

31UT

FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appliance.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, immediately call your gas

supplier.

www.desatech.com

121117-01C2

We cannot foresee every use which may be

made of our heaters. Check with your local

re safety authority if you have questions

about heater use.

Other standards govern the use of fuel gases

and heat producing products for specific

uses. Your local authorities can advise you

about these.

Carbon Monoxide Poisoning: Direct-Fired

means that all of the combustion products

enter the heated space. Even though this

heater operates very close to 100 % combus-

tion efciency, it still produces small amounts

of carbon monoxide. Some people are more

affected by carbon monoxide than others.

Early signs of carbon monoxide poisoning

resemble the u, with headaches, dizziness,

and/or nausea. If you have these signs, the

heater may not be working properly. Get fresh

air at once! Check for proper ventilation and

have heater serviced.

Propane Gas: Propane gas is odorless. An

odor-making agent is added to propane gas.

The odor helps you detect a propane gas

leak. However, the odor added to propane

gas can fade. Propane gas may be present

even though no odor exists.

SAFETY

SPECIFICATIONS

• Rating: 40,000 Btu/hr (11.7 kW)

• Type of Gas: Propane/LP Only

•

Gas Supply Pressure to Regulator:

Maximum - 150 psi (1034.2 kPa), Minimum - 5 psi (34.5 kPa)

• Gas Supply Pressure Regulator Out: 11" W.C. (2.74 kPa)

• Ignition: TD125 Electronic Ignition, TD126, TD127, TD128 Manual Ignition

• Fuel Consumption: 1.8 lbs./hr (0.9 kg/hr)

• Flame Safety: Thermocouple Operated Gas Valve

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects, or other reproduc-

tive harm.

WARNING: Not for home or

recreational vehicle use.

WARNING: Fire, burn, inhala-

tion, and explosion hazard. Keep

solid combustibles, such as build-

ing materials, paper or cardboard,

a safe distance away from the

heater as recommended by the

instructions. Never use the heater

in spaces which do or may contain

volatile or airborne combustibles,

or products such as gasoline, sol-

vents, paint thinner, dust particles

or unknown chemicals.

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury, property

damage, or death. Read the installation, operating, and

maintenance instructions thoroughly before installing

or servicing this equipment.

TABLE OF CONTENTS

Specications ...................................................... 2

Safety .................................................................. 2

Propane/LP Safety .............................................. 4

Unpacking Heater ................................................ 4

Assembly ............................................................. 5

Checking for Leaks .............................................. 8

Locating Heater ................................................... 9

Operation ............................................................. 9

Storage .............................................................. 10

Servicing .............................................................11

Replacement Parts .............................................11

Technical Service................................................11

Parts .................................................................. 12

Warranty ............................................................ 16

www.desatech.com

121117-01C 3

This is a propane, direct-red heater. Propane

is heavier than air. If propane leaks from a

connection or tting, it sinks to the oor, col-

lecting there with the surrounding air, forming

a potentially explosive mixture. Obviously,

propane leaks should be avoided, so set up

the propane supply with utmost care. Read

Propane/LP Safety, page 4 for additional in-

formation about detecting propane leaks. Leak

check new connections or reconnections with a

noncorrosive leak detection uid and follow all

connection instructions herein. Also, ask your

propane dealer for advice on the propane ap-

plication and supply installation and ask them

to check it if there are any questions.

When the heater is to be operated in the pres-

ence of other people the user is responsible

for properly acquainting those present with

the safety precautions and instructions, and

of the hazards involved.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

1. State of Massachusetts: The installation

must be made by a licensed plumber or

gas fitter in the Commonwealth of Mas-

sachusetts.

2. Check heater thoroughly for damage. DO

NOT operate a damaged heater.

3. DO NOT modify heater or operate a

heater which has been modied from its

original condition.

4. Use only propane/LP gas.

5. Use only VAPOR WITHDRAWAL pro-

pane supply. The propane cylinder must

be arranged for vapor-withdrawal, in

accordance with the Compress Gas As-

sociations, Small Propane Bottle Assem-

bly. If there is any question about vapor

withdrawal, ask your propane dealer.

6. Use only hose and regulator assembly

provided with heater.

7. Inspect hose assembly before each use

of heater. If there is excessive abrasion

or wear, or hose is cut, replace with hose

assembly listed on parts list before using

heater.

8. This heater is for OUTDOOR USE ONLY.

Make sure there is ample fresh air ventila-

tion. Do not use in buildings, garages or

other enclosed spaces.

SAFETY

Continued

9. If at any time gas odor is detected, IM-

MEDIATELY DISCONTINUE operation

until source of gas has been located and

corrected. Read Propane/LP Safety, page

4 for additional information about detect-

ing propane leaks.

10. Do not expose heater to water spray, rain

and/or dripping water.

11. Maintain minimum clearance to people

or normal combustible material (paper)

of 3 ft. (91.44 cm) from top and 2 ft.

(60.96 cm) from reector.

12. Operate only on a stable, level surface.

13. Do not spray aerosols near heater during

use or shortly thereafter.

14. Do not clean heater with combustible or

corrosive cleaners. Use a noncorrosive

leak detection uid.

15. Check control compartment burners and

circulation air passageways for free air

passage. Make sure there are no obstruc-

tions. These areas are a common location

for spider webs, which can present a

dangerous condition, damage heater and

render it unsafe for use. Heater must be

checked if any of the following conditions

exist:

a) Gas smell along with predominate yel-

low tipping of burner.

b) Heater does not reach temperature.

c) Uneven burner glow.

d)

Burner makes popping noises during nor-

mal use, other than during shutdown.

16. Use only a noncorrosive leak detection

uid to conduct leak tests whenever a

propane cylinder is connected. Bubbles

indicate a leak.

17. Do not adjust gas regulator. If you are

unsure of your appliances gas type or

pressure, call a qualied service person.

18. Place control knob in OFF position when

heater is not in use.

19. Always disconnect gas supply after heater

is turned OFF.

20. Do not move, handle or service while hot

or burning.

21. Allow 45 minutes to cool down after use

before attempting to move heater.

22. Do not operate this appliance in windy

conditions. Maximum allowable wind

speed is 10 mph (16 Km/h).

www.desatech.com

121117-01C4

23. Do not operate this appliance in tempera-

ture conditions below 40° F (5° C).

24. Keep heater away from areas where am-

mable liquids, vapors or solids are stored

or used.

25. If operated in salt air environments, unit will

require more frequent cleaning. Otherwise,

longevity of unit will deteriorate rapidly. Use

warm soapy water to clean unit.

26. Items or material stored under heater will

be subjected to radiant heat and could be

seriously damaged.

Any guard or other protective

device removed for servicing

must be replaced prior to operat-

ing the heater.

Surface temperatures become very

hot when operating heater. Children

and adults should stay away to

avoid burns or clothing ignition.

Young children should be care-

fully supervised when they are

in the area of the heater.

SAFETY

Continued

Clothing or other flammable

materials should not be hung

from the heater, or placed on or

near heater.

Installation and repair should

be done by a qualied service

person. The heater should be

inspected before use and at

least annually by a qualied

service person. More frequent

cleaning may be required as

necessary. It is imperative that

control compartments, burners

and circulating air passageways

of the heater be kept clean.

CAUTION: The gas pressure

regulator provided with this ap-

pliance must be used. This regu-

lator is set for an output pressure

of 11" W.C. (2.74 kPa).

PROPANE/LP SAFETY

WARNING: For outdoor use

only.

ASPHYXIATION HAZARD

• Do not use this heater for heating human

or animal living quarters.

• Do not use in unventilated areas.

• The ow of combustion and ventilation

air must not be obstructed.

• Proper ventilation air must be provided

to support the combustion air require-

ments of the heater being used.

• Refer to the Specifications, page 2,

heater data plate or contact DESA Heat-

ing, LLC to determine combustion air

ventilation requirements of the heater.

• Lack of proper ventilation air will lead

to improper combustion.

• Improper combustion can lead to car-

bon monoxide poisoning leading to

serious injury or death. Symptom of

carbon monoxide poisoning can include

headaches dizziness and difculty in

breathing.

UNPACKING HEATER

1. Carefully remove packaging material

from box.

2. Carefully remove heater components from

box. Inspect parts for possible shipping

damage. If any is found, immediately

notify dealer.

3. Check to make sure that all components

are included with your heater (see pages

12 and 13).

www.desatech.com

121117-01C 5

ASSEMBLY

Figure 2 - Base Assembly

Legs

Base

Pole

Support

1/4" Washer,

Lock Washer

and Nut

Figure 1 - Attaching Wheels to Base

5/16" Bolt,

Washer

and Nut

Figure 3 - Pole to Pole Support

Pole Support

Pole

Figure 4 - Attaching Back Cover

Back Cover

1/4" Large

Phillips Head

Screw and

1/4" Washer

Tools Required:

• 1) #2 Phillips Head Screwdriver

• 2) Adjustable Wrenches

Hardware packet provided with heater may

contain more parts than needed for heater

assembly.

1. Attach wheel assembly to base using two

5/16" bolts, two 5/16" washers and two

5/16" nuts (see Figure 1).

2. Attach legs to base using two 1/4" bolts,

four 1/4" washers, two 1/4" lock washers

and two 1/4" nuts per leg (see Figure

2). Place washer on bolt then insert bolt

through leg and into top of base. Attach

washer, lock washer and nut from under-

neath base. Finger tighten only. Repeat

for each bolt and leg. Do not fully tighten

until next step.

3. Secure pole support to legs using two

1/4" bolts, four 1/4" washers, two 1/4" lock

washers and two 1/4" nuts per leg (see

Figure 2). Repeat for each leg. Wrench

tighten nuts and bolts from step 1 and 2.

4. Remove 4 bolts and washers in collar of

pole support (see Figure 3). Place pole

over pole support collar. Reattach and

tighten 4 bolts and washers.

5. Attach back cover using four 1/4" large

Phillips head screws and four 1/4" wash-

ers as shown in Figure 4.

Base

Wheel

Assembly

Bolt and

Washer

1/4" Washer,

Lock Washer

and Nut

1/4" Bolt

and Washer

www.desatech.com

121117-01C6

Note: A cap support is provided on pole

support to lift top when changing propane/

LP cylinder.

8. Remove 4 screws in bottom of emitter.

Place burner assembly on emitter and

align holes. Replace screws. See Figures

7 and 8.

ASSEMBLY

Continued

Figure 7 - Placing Burner Assembly Onto

Emitter

6. Install tank door by placing cutouts on

sides over screws installed in step 5 (see

Figure 5).

7. Slide propane/LP cylinder top down pole

and over pole support (see Figure 6). Be

sure that propane/LP cylinder top rests

level on base.

Figure 5 - Attaching Tank Door

Cutout in

Tank Door

Figure 6 - Installing Cylinder Cap

Cylinder Cap

Burner

Assembly

Emitter

Figure 8 - Attaching Burner Assembly

and Emitter

Cap Support

www.desatech.com

121117-01C 7

ASSEMBLY

Continued

9. Thread manifold to bottom of burner

assembly (see Figure 9). Tighten with

wrenches (see Figure 10.)

10. Temporarily connect hose and regulator

to manifold. Connect hose and regulator

to a 20 lb. propane cylinder.

DO NOT LIGHT HEATER!

Open propane cylinder valve. Leak test

burner assembly and manifold connection

using a noncorrosive leak detection uid.

DO NOT USE FLAME. See Checking for

Leaks, page 8. When there is no sign of a

leak, turn off propane/LP cylinder valve and

disconnect regulator from propane/LP gas

cylinder. Slowly loosen connection between

manifold and hose and regulator assembly.

Propane gas left in hose will escape.

11. Remove bolts from burner assembly.

Carefully lean base and pole assembly

over and insert manifold and burner

assembly through pole (see Figure 11).

Replace bolts.

12. Remove blue lm from dome top. Dome

attaches to burner assembly with three

5/16" nuts and six 5/16" washers.

Place 1 washer on each threaded stud

of burner assembly. Place dome over

studs. Attach 3 washers and nuts to

studs. See Figure 12.

Figure 11 - Sliding Manifold and Burner

Assembly into Pole

Figure 9 - Attaching Manifold to Burner

Assembly

Manifold

Figure 10 - Tightening Manifold and

Burner Assembly

Burner

Assembly

Figure 12 - Attaching Dome to Burner

Assembly

Burner

Assembly

Bolts

Removed

From Here

Pole

Bolts Reinstalled

Through Here

Manifold

www.desatech.com

121117-01C8

Figure 13 - Attaching Regulator and

Hose Assembly

Figure 14 - Propane Tank and Safety

Chain

13. Remove tank door. Wrench tighten regu-

lator and hose assembly to manifold as

shown in Figure 13. Check connections

for gas leaks (see Checking for Leaks).

Note: Make sure hose and regulator as-

sembly attached to manifold are never

bent or kinked during installation and

operation of heater.

14. Place propane/LP tank on top of base.

Attach regulator.

15. Install propane tank safety chain around

tank and into openings on legs as shown

in Figure 14.

16. Reinstall door.

ASSEMBLY

Continued

CHECKING FOR LEAKS

IMPORTANT: The heater must be leak tested

before any further assembly is done. Use only

a noncorrosive leak detection uid. DO NOT

USE FLAME.

Turn control knob to the OFF position. Se-

curely connect regulator to propane/LP gas

cylinder. Open propane/LP cylinder valve.

Apply a noncorrosive leak detection uid to

connections at the manifold and regulator

connections. Bubbles forming show a leak.

In case of any leaks, turn off propane/LP

cylinder valve, remove manifold, check and

clean connection. Reconnect manifold and

leak test again.

Upon completion of leak test, and when

there is no sign of a leak, turn off propane/LP

cylinder valve and disconnect regulator from

propane/LP gas cylinder. Remove propane/LP

gas cylinder and continue to next step.

Cap Support

Safety

Chain

www.desatech.com

121117-01C 9

OPERATION

WARNING: If you smell gas:

• Shut off gas to the appliance.

• Extinguish any open ames.

• If odor continues, immediately

call your gas supplier.

See safety warnings and pre-

cautions starting on the front

page of this manual for more

information.

PREPARING FOR OPERATION

1. Check heater for possible shipping damage.

If any is found, immediately notify dealer.

2. Follow all safety information starting on

page 2.

3. Check and assure control knob is in the

OFF position.

LOCATING HEATER

WARNING: Do not move

heater when lit. Allow heater to

cool before moving.

1. Locate pop-out wheel decal on base of

heater (see Figure 15).

Figure 15 - Pop-out Wheels

Wheel

Pop-out

Wheel

Decal

Figure 16 - Locating Heater

2. Standing on decal side of heater, care-

fully lean heater away from you to access

wheels underneath base.

3. Swing wheels out from under base to

relocate heater.

4. Replace wheels underneath base after

placing heater in desired location.

4. Place propane/LP gas cylinder inside

cylinder base. Securely connect regulator

to propane/LP gas cylinder.

5. Turn cylinder valve on. Apply a noncor-

rosive leak detection uid to connection

at regulator and cylinder. Bubbles forming

show a leak.

6. In case of any leaks, turn off propane/LP

cylinder valve, undo leaking connection.

Check and clean connection. Reconnect

regulator and leak test again.

IMPORTANT: On new installations or routine

gas cylinder changes. The system must be

purged of air before use. Turn control knob

to the pilot setting. Press and hold for 30-40

seconds before attempting to light pilot.

www.desatech.com

121117-01C10

STORAGE

1. Allow at least 45 minutes for heater to cool

down after using.

2. Store heater upright in a sheltered area

away from inclement weather and dust.

3. If desired, cover heater after heater has

cooled.

4. If heater is not to be used for an extended

period of time, disconnect and remove

propane/LP gas cylinder and store in ac-

cordance with the Standard for Storage

and Handling of Liquefied Petroleum

Gases, ANSI/INFPA 58.

TO LIGHT

1. Shut main gas supply valve on propane

cylinder off. Set heater control knob to

OFF position. Wait 5 minutes.

2. Open main gas supply valve on propane

cylinder.

3. Turn heater control knob to the PILOT po-

sition. Push and hold for 5 seconds. Press

igniter button until pilot is lit. Continue to

hold heater control valve for 30 seconds

then release.

CAUTION: Do not attempt to

slide viewing hole cover when

main burner is lighting, operat-

ing or hot.

4. TO MATCH LIGHT PILOT: Rotate match

light hole cover. Apply ame to pilot burner

while holding knob in for 20 seconds or

until pilot remains lit when knob is re-

leased.

5. Knob can now be turned to the ON

position.

IMPORTANT: Smoke and odor (not a gas

odor) emission may occur in the rst 30 min-

utes of use. Run heater at high setting for at

least 30 minutes to eliminate this problem.

Figure 17 - Heater Controls and Viewing

Hole and Cover

Viewing Hole

and Cover

Ignitor Button

Control

Knob

WARNING: If you smell gas

while in use, immediately press

and turn control knob to the OFF

position to shut down heater.

TO SHUT DOWN

1. Turn control knob to the OFF position.

2. Shut off main gas supply.

3. Wait 5 minutes before relighting heater.

OPERATION

Continued

www.desatech.com

121117-01C 11

REPLACEMENT PARTS

When calling DESA Heating, LLC have

ready

• your name

• your address

• model number of your heater

• how heater was malfunctioning

• purchase date

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If

they can’t supply original replacement part(s),

either contact your nearest Parts Central

(listed in Authorized Service Center booklet)

or call DESA Heating, LLC at 1-866-672-6040

for referral information.

When calling DESA Heating, LLC have

ready

• model number of your heater

• the replacement part number

SERVICING

To assure safety, proper function and lon-

gevity of the heater, regular maintenance is

required. The frequency of maintenance will

depend on the usage of the unit. Review the

following concerning the criteria for a properly

functioning heater. Failing to follow proper,

regular maintenance will void warranty.

A hazardous condition may result if a heater

is used that has been modied or is not func-

tioning properly. When the heater is working

properly:

• The ame is contained within the heater.

• The ame is essentially blue with perhaps

some yellow tipping.

• There is no strong disagreeable odor, eye

burning or other physical discomfort.

• There is no smoke or soot internal or ex-

ternal to the heater.

• There are no unplanned or unexplained

shut downs of the heater.

The parts list shows the heater as it was con-

structed. Do not use a heater which is different

from that shown. In this regard, use only the

hose, regulator and cylinder connection tting

(called a POL tting) supplied with the heater.

IMPORTANT: Do not use alternates. For this

heater, the regulator must be set as shown

in Specications, page 2. If there is any un-

certainty about the regulator setting, have it

checked by a qualied service person.

WARNING: Use only original

replacement parts. This heater

must use design-specic parts.

Do not substitute or use generic

parts. Improper replacement

parts could cause serious or fa-

tal injuries. This will also protect

your warranty coverage for parts

replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If

they can’t supply original replacement part(s),

either contact your nearest Parts Central or

call DESA Heating, LLC at 1-866-672-6040.

TECHNICAL SERVICE

A heater which is not working right must be

repaired, but only by a trained, experienced

service person. To nd the service center

closest to you, or if you have further questions

about this heater, contact DESA Heating, LLC

at 1-866-672-6040. When calling, please

have your model and serial numbers of your

heater ready.

You can also visit DESA Heating, LLC's web

site at www.desatech.com.

You may also obtain in-warranty or out of

warranty service by taking the product to your

local service center.

www.desatech.com

121117-01C12

PARTS

MODELS

TD125, TD126, TD127, TD128

1

2

3

4

34

33

22

31

29

30

23

35

24

25

26

32

19

27

21

9

10

7

13

15

12/14

16

17

11

5

8

20

6

28

18

www.desatech.com

121117-01C 13

KEY

NO. PART NO. DESCRIPTION QTY

1 V01-001 Dome • • • • 1

2 V01-002 Emitter Cap • • • • 1

3 V01-003 Emitter • • • • 1

4 V01-005 Emitter Bottom • • • • 1

5 V01-008 Pilot Cover • • • • 1

6 V01-004 Main Burner • • • • 1

7 V01-028 Copper Nut • • • • 1

8 V01-007 Pilot Burner Assembly • • • • 1

9 V01-006 View-hole Cover • • • • 1

10 V01-011 Insulation Panel • • • • 1

11 V01-009 Face Panel (English Operation) • • • • 1

12 V01-026 Main Nozzle • • • • 1

13 V01-034 Knob • • • • 1

14 V01-027 Nozzle Connector • • • • 1

15 V01-012 Valve Support • • • • 1

16 V01-029 Main Burner Gas Line • • • • 1

17 V01-037 Valve Assembly • • • • 1

18 V01-030 Connector Tube • • • • 1

19 V01-036 Ignitor, Manual • • • 1

V01-036E Ignitor, Electronic • 1

20 V01-023 Ignitor Line • • • • 1

21 V01-031 Gas Line • • • • 1

22 see page 14 Post • • • • 1

23 see page 14 Cylinder Cap • • • • 1

24 see page 14 Post Support • • • • 1

25 V01-022 Cylinder Cap Support • • • • 1

26 see page 14 Back Cover • • • • 1

27 V01-045 Regulator Assembly • • • • 1

28 see page 14 Door • • • • 1

29 see page 14 Legs • • • • 3

30 V01-032 Chain • • • • 1

31 see page 14 Base Kit • • • • 1

32 see page 14 Valve Housing Bottom • • • • 1

33 V01-013 Gas Line Fixed Plate • • • • 1

34 V01-010 Valve Housing • • • • 1

35 V01-035 O Ring • • • • 1

PARTS AVAILABLE - NOT SHOWN

NV02-08-00 Wheel Assembly • • • • 1

121119-01 Hardware Package • • • • 1

114124-01 Warning Hang Tag, English • • • • 1

114124-02 Warning Hang Tag, Spanish • • • • 1

114124-03 Warning Hang Tag, French • • • • 1

114122-02 Operation Decal, English • • • • 1

114124-06 Operation Hang Tag, Spanish • • • • 1

114124-07 Operation Hang Tag, French • • • • 1

121420-01 Wheel Warning Decal • • • • 1

PARTS

This list contains replaceable parts used in your heater. When ordering parts, follow the

instructions listed under Replacement Parts on page 11 of this manual.

TD125

TD126

TD127

TD128

www.desatech.com

121117-01C14

KEY

NO. PART NO. DESCRIPTION QTY

22 V01-015SS Post, Stainless Steel • 1

V01-015BK Post, Black • 1

V01-015WH Post, White • 1

V01-015HB Post, Hammered Bronze • 1

23 V01-017SS Cylinder Cap, Stainless Steel • 1

V01-017BK Cylinder Cap, Black • 1

V01-017WH Cylinder Cap, White • 1

V01-017HB Cylinder Cap, Hammered Bronze • 1

24 V01-016SS Post Support, Stainless Steel • 1

V01-016BK Post Support, Black • 1

V01-016WH Post Support, White • 1

V01-016HB Post Support, Hammered Bronze • 1

26 V01-019SS Back Cover, Stainless Steel • 1

V01-019BK Back Cover, Black • 1

V01-019WH Back Cover, White • 1

V01-019HB Back Cover, Hammered Bronze • 1

28 V01-018SS Door, Stainless Steel • 1

V01-018BK Door, Black • 1

V01-018WH Door, White • 1

V01-018HB Door, Hammered Bronze • 1

29 V01-020SS Legs, Stainless Steel • 3

V01-020BK Legs, Black • 3

V01-020WH Legs, White • 3

V01-020HB Legs, Hammered Bronze • 3

31 V01-021K-SS Base Kit, Stainless Steel • 1

V01-021K-BK Base Kit, Black • 1

V01-021K-WH Base Kit, White • 1

V01-021K-HB Base Kit, Hammered Bronze • 1

32 V01-014SS Valve Housing Bottom, Stainless Steel • 1

V01-014BK Valve Housing Bottom, Black • 1

V01-014WH Valve Housing Bottom, White • 1

V01-014HB Valve Housing Bottom, Hammered Bronze • 1

TD125

TD126

TD127

TD128

PARTS

www.desatech.com

121117-01C 15

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

NOTES

WARRANTY

KEEP THIS WARRANTY

121117-01

Rev. C

02/08

DESA Heating, LLC

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

1-866-672-6040

LIMITED WARRANTY

DESA Heating, LLC warrants this product and any parts thereof, to be free from defects in materials and

workmanship for one (1) year for residential home owner usage or 90 days for commercial/industrial

usage from the date of first purchase when operated and maintained in accordance with instructions.

This warranty is extended only to the original retail purchaser, when proof of purchase is provided.

This warranty covers only the cost of parts and labor required to restore the product to proper operating

condition. Transportation and incidental costs associated with warranty repairs are not reimbursable

under this warranty.

Warranty service is available only through authorized dealers and service centers.

This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper

maintenance, normal wear, alteration, modification, tampering, contaminated fuels, repair using improper

parts, or repair by anyone other than an authorized dealer or service center. Routine maintenance is

the responsibility of the owner.

THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED

OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-

LAR PURPOSE.

DESA Heating, LLC assumes no responsibility for indirect, incidental or consequential damages. Some

states do not allow the exclusion or limitation of incidental or consequential damages or limitations or

exclusions may not apply to you. This Limited Warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

This warranty does not cover discoloration due to operation of heater. The only warranty applicable is

our standard written warranty. We make no other warranty, expressed or implied.

WARRANTY SERVICE

Should your heater require service, return it to your nearest authorized service center. Proof of purchase

must be presented with the heater. The heater will be inspected. A defect may be caused by faulty materi-

als or workmanship. If so, DESA Heating, LLC will repair or replace the heater without charge.

REPAIR SERVICE

Return the heater to your nearest authorized service center. Each Service Center is independently owned

and operated. Repairs not covered by the warranty will be billed at standard prices.

For information about this warranty write:

Model (

located on product or identication tag

) _____________________________

Serial No. (

located on product or identication tag

) __________________________

Date Purchased __________________________

Keep receipt for warranty verication.

Page is loading ...

www.desatech.com

121117-01C12

PIEZAS

MODELOS

TD125, TD126, TD127, TD128

1

2

3

4

34

33

22

31

29

30

23

35

24

25

26

32

19

27

21

9

10

7

13

15

12/14

16

17

11

5

8

20

6

28

18

Page is loading ...

www.desatech.com

121117-01C12

PIÈCES

MODÈLES

TD125, TD126, TD127, TD128

1

2

3

4

34

33

22

31

29

30

23

35

24

25

26

32

19

27

21

9

10

7

13

15

12/14

16

17

11

5

8

20

6

28

18

Page is loading ...

Desa td126 Owner's manual

This manual is also suitable for

Desa td126 Owner's manual

in other languages

Related papers

Other documents