Black & Decker 90504494 User manual

VEA EL ESPA OL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

CC

OO

RR

DD

LL

EE

SS

CC

OO

MM

PP

AA

CC

TT

DD

RR

II

LL

SS

WW

II

TT

HH

LL

AA

SS

EE

RR

SS

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE

A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

T

HANK

YOU

FOR

CHOOSING

B

LACK

&

D

ECKER

!

G

O

T

O

WWW

.B

LACKAND

D

ECKER

.

COM

/N

EW

O

WNER

T

O

REGISTER

YOUR

NEW

PRODUCT

.

Catalog Numbers

BDGL1200, BDGL1440,

BDGL1800

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 1

GENERAL SAFETY RULES

WARNING! Read and understand all instructions. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious injury. The term “power tool”

in all of the warnings listed below refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust

. Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions

can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools.

Unmodified

plugs and matching outlets will reduce risk of electric shock

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence

of drugs, alcohol or medication.

A moment of inattention while operating power tool

may result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before

plugging in.

Carrying power tools with your finger on the switch or plugging in power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be

avoided.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of these devices

can reduce dust-related hazards.

2

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 2

3

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools

operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool,

taking into account the working conditions and the work to be performed.

Use

of the power tool for operations different from those intended could result in a

hazardous situation.

5) Battery tool use and care

a) Ensure the switch is in the off position before inserting battery pack. Inserting

the battery pack into power tools that have the switch on invites accidents.

b) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another

battery pack.

c) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

d) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

e) Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

b) If the replacement of the supply cord is necessary,

this has to be done by the

manufacturer or his agent in order to avoid a safety hazard.

Specific Safety Rules

• Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

• When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use. Some tools with large battery packs will stand upright but may be easily

knocked over.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 3

First Aid Measures for Gel Components

If gel within the comfort grip becomes exposed and results in skin contact wash with

soap and water;

For eye contact, flush with flowing water. If swallowed, seek medical attention.

Material Safety Data Sheet (MSDS) available from 1-800-544-6986

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles

away from face and body.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating

current

......................direct current

n

o ........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations

per minute

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the

tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently

come in contact with conductive materials such as keys, coins, hand tools and the like.

The US Department of Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and

carryon luggage) UNLESS they are properly protected from short circuits. So when

transporting individual batteries, make sure that the battery terminals are protected and

well insulated from materials that could contact them and cause a short circuit.

4

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 4

5

D

A

9

8

10

11

FUNCTIONAL DESCRIPTION

1. Variable speed switch

2. Forward/reverse slider

3. Torque adjustment collar

4. Chuck

5. Laser apertures

6. Laser on/off switch

7. Laser direction actuator

8. Battery

9. Cup charger

10. Jack plug charger

(BDGL1200)

B

C

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 5

Page is loading ...

7

M

N

SAFETY INSTRUCTIONS - LASERS

CAUTION: Laser Radiation, avoid direct eye exposure, serious eye injury can

result.

• Do not use optical tools such as a telescope or transit to view the laser beam.

• Position the laser so unintentional eye contact will be avoided.

• Do not operate the laser around children or allow children to operate the laser.

• Do not disassemble. Modifying the product in any way can increase the risk of laser

radiation.

WARNING: Use of controls or adjustments or performance of procedures other than

those specified in this manual may result in hazardous laser radiation exposure.

• Do not operate in explosive atmospheres, such as in the presence of flammable liquids,

gases, or dust.

• Store idle product out of reach of children and other untrained persons. Lasers are

dangerous in the hands of untrained users.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one laser, may create a risk of injury when used on

another laser.

• Repairs and servicing MUST be performed by a qualified repair facility. Repairs

performed by unqualified personnel could result in serious injury.

• Do not remove or deface warning labels. Removing labels increases the risk of exposure

to radiation.

• For indoor use only.

• This product is intended for use in a temperature range of 41°F(5°C) - 104°F(40°C).

For your convenience and safety, the following labels are on the laser.

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

PER EN60825-1:11994+AII+A2

Pmax- 2.8mW,

=633-670nm

COMPLIES WITH 21CFR PARTS

1040.10 AND 1040.11 EXCEPT FOR

DEVIATIONS PURSUANT TO LASER

NOTICE NO.50, DATED JULY 26,2001.

BDGL1800

BDGL1200/

BDGL1440

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 7

8

SAFETY WARNINGS AND INSTRUCTIONS: CHARGING

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary markings on

battery charger, battery pack, and product using battery pack.

3. CAUTION: To reduce the risk of injury, charge only Black & Decker Batteries. Other

types of batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round

jacketed extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must

be suitable for outdoor use. Any cord marked for outdoor use can also be used for

indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is

suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number

of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity

than 18 gauge. When using more than one extension to make up the total length, be

sure each extension contains at least the minimum wire size.

9. Use only the supplied charger when charging the battery pack. The use of any other

charger could damage the battery pack or create a hazardous condition.

10. Use only one charger when charging.

11. Do not attempt to open the charger. There are no customer serviceable parts inside.

Return to any authorized Black & Decker service center.

12. DO NOT incinerate the battery pack even if it is severely damaged or completely worn

out. The batteries can explode in a fire.

13. A small leakage of liquid from the battery pack cells may occur under extreme usage,

charging or temperature conditions. This does not indicate a failure. However, if the

outer seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a

25-35% solution of potassium hydroxide.

CHARGING THE BATTERY PACK (BDGL1200) FIGURE C

THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE

ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE

SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power.

1. Make sure the battery pack is fitted properly into the drill. Insert the charger plug (10)

into the connector (11) as shown in figure C.

2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet and let the battery

pack charge initially for 9 hours. After the initial charge, under normal usage, your

battery pack should be fully charged in 3 to 9 hours. NOTE: Do not charge by

means of an engine generator or DC power source. Use only 120V AC

3. Disconnect the charger from the outlet, then disconnect the charger from the tool.

NOTE: Do not use the tool while it is connected to the charger.

NOTE: To remove the battery pack from the drill, press down on the release button

(12) on the back of the battery pack (figure E) and slide out.

NOTE: Turn off laser before inserting / removing the battery pack. When installing

battery pack, be certain that it is inserted fully into the tool cavity until it “clicks” into

place.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 8

9

CHARGING THE BATTERY PACK (BDGL1440, BDGL1800) FIGURE D

THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE

ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE

SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power.

1. Plug the charger (9) into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not

charge by means of an engine generator or DC power source. Use only 120V

AC.

2. Slide the charger onto the battery pack (8) as shown in figure D and let the battery

pack charge initially for 9 hours. After the initial charge, under normal usage, your

battery pack should be fully charged in 3 to 9 hours.

3. Unplug charger, and remove the battery pack. Place the battery pack in the tool

and be certain that it is inserted fully into the tool cavity until it “clicks” into

place.

NOTE: To remove the battery pack from the drill, press down on the release button

(12) on the back of the battery pack (figure E) and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your battery pack should be fully charged in 3 to 9 hours. If the

battery pack is run-down completely, it may take up to 9 hours to become fully

charged. Your battery pack was sent from the factory in an uncharged condition.

Before attempting to use it, it must be charged for at least 9 hours.

2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above

105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack.

Longest life and best performance can be obtained if battery pack is charged when

air temperature is about 75°F.(24°C).

3. While charging, the charger may hum and become warm to touch. This is a normal

condition and does not indicate a problem.

4. If the battery pack does not charge properly—(1) Check current at receptacle by

plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to

a light switch which turns power off when you turn out the lights. (3) Move charger

and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C)

(4) If the receptacle and temperature are OK, and you do not get proper charging,

take or send the battery pack and charger to your local Black & Decker service

center. See Tools Electric in yellow pages.

5. The battery pack should be recharged when it fails to produce sufficient power on

jobs which were easily done previously. DO NOT CONTINUE using product with its

battery pack in a depleted condition.

6. To prolong battery life, avoid leaving the battery pack on charge for extended periods of

time (over 30 days without use). Although overcharging is not a safety concern, it can

significantly reduce overall battery life.

7. The battery pack will reach optimum performance after being cycled 5 times during

normal usage. There is no need to run the batteries down completely before

recharging. Normal usage is the best method of discharging and recharging the

batteries.

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the

battery pack.

2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always

expect the stall. Grip the drill firmly with both hands to control the twisting action and

prevent loss of control which could cause personal injury. If a stall does occur, release

the trigger immediately and determine the reason for the stall before re-starting.

OPERATING INSTRUCTIONS

TRIGGER SWITCH & REVERSING BUTTON (FIGURE F)

• The drill is turned ON and OFF by pulling and releasing the trigger switch (1). The

farther the trigger is depressed, the higher the speed of the drill.

• A forward/reverse control button (2) determines the direction of the tool and also

serves as a lock off button.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 9

10

• To select forward rotation, release the trigger switch and depress the forward/reverse

control button to the left.

• To select reverse, depress the forward/reverse control button the opposite direction.

NOTE: The center position of the control button locks the tool in the off position.

When changing the position of the control button, be sure the trigger is released.

DUAL RANGE GEARING (FIGURE G) (BDGL1800 ONLY)

The dual range feature of the BDGL1800 allows you to shift gears for greater versatility.

• To select low speed, high torque setting (position 1), turn tool off and permit to stop.

Slide gear shifter button (13) forward towards the chuck.

• To select the high speed, low torque setting (position 2), turn tool off and permit to

stop. Slide gear shifter button (13) back (away from chuck). NOTE: Do not change

gears when tool is running. If you are having trouble changing gears, make sure that

the gear shifter button is either completely pushed forward or completely pushed back.

TORQUE CONTROL (FIGURE H)

This tool is fitted with a collar (3) to select the operating mode and to set the torque for

tightening screws. Large screws and hard workpiece materials require a higher torque

setting than small screws and soft workpiece materials.

• For drilling in wood, metal and plastics, set the collar to the drilling position symbol .

• For screwdriving, set the collar to the desired setting. If you do not yet know the

appropriate setting, proceed as follows:

• Set the collar to the lowest torque setting.

• Tighten the first screw.

• If the clutch ratchets before the desired result is achieved, increase the collar setting

and continue tightening the screw. Repeat until you reach the correct setting. Use this

setting for the remaining screws.

KEYLESS CHUCK (FIGURE I)

To insert a drill bit or other accessory:

1. Grasp the rear half of the chuck (4) with one hand and use your other hand to rotate

the front half in the counterclockwise direction, as viewed from the chuck end.

2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding

the rear half of the chuck and rotating the front portion in the clockwise direction as

viewed from the chuck end.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the

front part of the chuck and turning the tool on. Damage to the chuck and personal injury

may occur when changing accessories.

OPERATING THE LASER

Your drill is equipped with a laser which is turned on and off separately from the tool.

WARNING: NEVER aim the beam at a workpiece with a reflective surface. Bright

shiny reflective sheet steel or similar reflective surfaces are not recommended for laser

use. Reflective surfaces could direct the beam back toward the operator.

CAUTION: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare

into the laser light source. Never aim light at another person or object other than

the workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses

will reduce overall vision for the application and interfere with the normal operation of the

tool.

SWITCHING THE LASER ON AND OFF (FIGURE J)

• To turn the laser on, slide the laser on/off button (6) to the (I) position.

• To turn the laser off, slide the laser on/off button (6) to the (0) position.

SETTING THE DIRECTION OF THE BEAM (FIGURE K)

The laser beam can be set for both horizontal and vertical leveling applications.

• To change the laser line projection, move the laser direction actuator (7) in the

direction that you want the laser line to project.

NOTE: Laser will not work if the drill is inverted.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 10

11

USING THE LASER LEVEL FUNCTION (HORIZONTALLY LEFT - FIGURE L)

• Place the tool flat against the wall as shown.

• Slide the laser on/off switch (6) to position I to switch the laser ON.

• Move the laser direction actuator (7 in Figure K) to the left most position. Laser will

project horizontally to the left from the laser aperture (5 in Figure B).

• Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from

vertical.

• Slide the laser on/off switch (6) to position 0 to switch the laser OFF.

NOTE: Laser will not work if the drill is inverted.

USING THE LASER LEVEL FUNCTION (VERTICALLY - FIGURE M)

• Place the tool flat against the wall as shown.

• Slide the laser on/off switch (6) to position I to switch the laser ON.

• Move the laser direction actuator (7 in Figure K) to the center position. Laser will

project vertically from the laser aperture (5 in Figure B).

• Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from

vertical.

• Slide the laser on/off switch (6) to position 0 to switch the laser OFF.

NOTE: Laser will not work if the drill is inverted.

USING THE LASER LEVEL FUNCTION (HORIZONTALLY RIGHT - FIGURE N)

• Place the tool flat against the wall as shown.

• Slide the laser on/off switch (6) to position I to switch the laser ON.

• Move the laser direction actuator (7 in Figure K) to the right most position. Laser will

project horizontally to the right from the laser aperture (5 in Figure B).

• Move the tool as necessary to position the laser line.

NOTE: The laser lines will only be level if the tool is kept within 5 degrees from

vertical.

• Slide the laser on/off switch (6) to position 0 to switch the laser OFF.

NOTE: Laser will not work if the drill is inverted.

SCREW DRIVING

For driving fasteners, the reversing button should be pushed to the left. Use reverse

(button pushed to the right) for removing fasteners. When moving from forward to reverse,

or vice versa, always release the trigger switch first.

ON BOARD BIT STORAGE

A bit storage slot is built-in to the area just above the battery pack.

DRILLING

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the

drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with two hands to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the

last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Make sure switch turns drill on and off.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 11

12

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service personnel, always using identical replacement

parts.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack

installation.

• Battery pack not charged. • Check battery pack charging

requirements.

• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into

charger until red LED

appears.

• Charger not plugged in. • Plug charger into a working

outlet. Refer to “Important

Charging Notes” for more

details.

• Surrounding air temperature • Move charger and battery

too hot or too cold. pack to a surrounding air

temperature of above 40

degrees F (4,5°C) or below

105 degrees F (+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the location of the

service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

The RBRC“ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs

to recycle the battery (or battery pack) at the end of its useful life have already been paid

by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in

the trash or municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service

center or to your local retailer for recycling. You may also contact your local recycling

center for information on where to drop off the spent battery, or call 1-800-8-BATTERY.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 12

13

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide

customers with efficient and reliable power tool service. Whether you need technical

advice, repair, or genuine factory replacement parts, contact the Black & Decker location

nearest you. To find your local service location, refer to the yellow page directory under

"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge

in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory and on our website

www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state or province to province.

Should you have any questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

TECHNICAL SPECIFICATIONS OF LASER:

Laser diode wavelength: 633-670nm (red color)

Laser Class: Class II

Accuracy: +/- 3.0mm (1/8”) @ 3m (10')

Operating temperature: 50°F (10°C) - 104° F (40°C)

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 13

14

PP

EE

RR

CC

EE

UU

SS

EE

SS

CC

OO

MM

PP

AA

CC

TT

EE

SS

AA

NN

SS

FF

II

LL

AA

VV

EE

CC

LL

AA

SS

EE

RR

SS

MODE D EMPLOI

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

1-800-544-6986

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART

DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

M

ERCI

D

’

A

VOIR

CHOISI

B

LACK

& D

ECKER

!

V

ISITEZ

WWW

.B

LACKAND

D

ECKER

.

COM

/N

EW

O

WNER

POUR

ENREGISTRER

VOTRE

NOUVEAU

PRODUIT

.

CONSERVER CE MANUEL POUR UN USAGE ULT RIEUR.

N¡ de catalogue

BDGL1200, BDGL1440,

BDGL1800

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 14

Page is loading ...

29

TT

AA

LL

AA

DD

RR

OO

SS

CC

OO

MM

PP

AA

CC

TT

OO

SS

II

NN

AA

LL

MM

BB

B

RR

II

CC

OO

SS

CC

OO

NN

LL

SS

EE

RR

N MEROS DE

CAT LOGO

BDGL1200, BDGL1440,

BDGL1800

MANUAL DE INSTRUCCIONES

CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.

ANTES DE DEVOLVER ESTE PRODUCTO POR

CUALQUIER MOTIVO, LLAME AL

(55)5326-7100

ANTES DE LLAMAR, TENGA EL NÚMERO DE CATÁLOGO Y EL CÓDIGO DE FECHA PREPARADOS. EN

LA MAYORÍA DE LOS CASOS, UN REPRESENTANTE DE BLACK & DECKER PUEDE RESOLVER EL

PROBLEMA POR TELÉFONO. SI DESEA REALIZAR UNA SUGERENCIA O COMENTARIO, LLÁMENOS. SU

OPINIÓN ES FUNDAMENTAL PARA BLACK & DECKER.

¡G

RACIAS

POR

ELEGIR

B

LACK

& D

ECKER

!

V

A

Y

A

WWW

.B

LACKAND

D

ECKER

.

COM

/N

EW

O

WNER

P

ARA

REGISTRAR

SU

NUEVO

PRODUCT

O

.

90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 29

Page is loading ...

Black & Decker 90504494 User manual

Black & Decker 90504494 User manual

in other languages

Related papers

Other documents