IMPORTANT NOTE
●
Handle the liquid crystal display (LCD) with care:
- The LCD is a very delicate display device: Do not press its surface with
force, hit it or prick it with a sharp object.
- If you push the LCD surface, unevenness in display may occur. If
unevenness does not disappear, turn the camcorder off, wait for a few
moments, and then turn it on again.
- Do not place the camcorder with the open LCD screen down.
- Close the LCD screen when not using the camcorder.
Liquid crystal display:
- The LCD screen the product of highly precise technology. Among the total
number of pixels (approx. 230,000 pixels for LCD screen), 0.01% or less
pixels may be missing (black dots) or may remain lit as colored dots (red,
blue, green). This shows the limitations of the current technology, and does
not indicate a fault that will interfere with recording.
- The LCD screen will be slightly dimmer than usual when the camcorder is
at low temperature, as in cold areas, or immediately after power is turned
on. Normal brightness will be restored when the temperature inside the
camcorder rises. This has no effect on the images in the storage media, so
there is no cause for concern.
●
Hold the HD camcorder correctly:
Do not hold the HD camcorder by the LCD screen when lifting it: the LCD screen
could detach and the HD camcorder may fall.
●
Do not subject the HD camcorder to impact:
-
This HD camcorder is a precision machine. Take great care that you do
not strike it against a hard object or let it fall.
- Do not use the HD camcorder on a tripod (not supplied) in a place where it
is subject to severe vibrations or impact.
●
No sand or dust!
Fine sand or dust entering the HD camcorder or AC power adaptor could cause
malfunctions or defects.
●
No water or oil!
Water or oil entering the HD camcorder or AC power adaptor could cause
electric shock, malfunctions or defects.
●
Heat on surface of product:
The surface of the HD camcorder will be slightly warm when in use, but this does
not indicate a fault.
●
Be careful of ambient temperature:
- Using the HD camcorder in a place where the temperature is over 60°C
(140°F) or under 0°C (32°F) will result in abnormal recording/playback.
- Do not leave the HD camcorder on a beach or in a closed vehicle
where the temperature is very high for a long time: This could cause a
malfunction.
precautions when using
vii_ English
中文 _vii
重要注意事项
细心处理液晶显示器
(LCD)
:
-
LCD
是非常精密的显示设备:切勿用力压其表面,或使用尖锐的
物体击打或刺戳。
- 如果您按压
LCD
表面,可能会在显示时出现不平现象。如果不平
现象不消失,请关闭摄像机,等待片刻后再次打开。
- 切勿使打开的
LCD
屏幕向下放置摄像机。
- 在不使用摄像机时关闭
LCD
显示器。
液晶显示:
-
LCD
屏幕是采用高精密技术制造的产品。在总像素(
LCD
显示器
的大约
230,000
像素)中,
0.01%
或更少的像素可能会损失(黑
点),或可能以彩色(红、蓝和绿色)的点亮起。
这表明了当前技
术的局限性,但不表示是影响录制的故障。
- 当摄像机在温度较低的环境(如在寒冷地区)时,
LCD
屏幕会比
正常时稍暗,或在打开电源后显示正常。当摄像机内部的温度上
升时,会恢复到原来的亮度。注意,上述现象对存储介质中的图
像没有什么影响,因此无需顾虑。
正确把持数码摄像机:
- 不要握住数码摄像机的
LCD
显示器来提起它:
LCD
显示器可能会
拆离,从而导致数码摄像机跌落。
切勿撞击数码摄像机:
- 本数码摄像机是精密机器。
要特别小心,不要让其撞击硬物或摔落。
- 切勿在严重振动或撞击的地方将数码摄像机放在三脚架上使用。
要避免沙尘!
- 细沙或灰尘进入数码摄像机或交流电源适配器会引起故障。
要避免水或油!
- 水或油进入数码摄像机或交流电源适配器会引起触电或故障。
产品表面变热:
- 在使用时,数码摄像机表面会轻微变热,但这并不表示有故障。
注意异常的环境温度:
- 在温度高于
60°C (140°F)
或低于
0°C(32°F)
的地方使用数码摄像
机,可能会导致录制
/ 播放不正常。
- 切勿将数码摄像机放在沙滩上或温度长时间会很热的封闭车辆中:
这样可能会导致发生故障。
•
•
•
•
•
•
•
使用须知