Ugolini ARCTIC COMPACT User manual

ARCTIC

Compact 12L - 20L

MANUALE D’ISTRUZIONE

OPERATOR’S MANUAL

CARNET D’INSTRUCTIONS

GEBRAUCHSANWEISUNG

MANUAL DE INSTRUCCIONES

2

Arctic Compact 12-20

DICHIARAZIONE DI CONFORMITÀ CE

Noi Ugolini spa, via dei Pioppi, 33 20090 Opera Milano ITALY dichiariamo, sotto la nostra responsabilità, che l’apparecchio DISTRIBUTORE DI

BEVANDE FREDDE - Marca: UGOLINI S.p.A. - Fabbricante: UGOLINI S.p.A. - Modelli: ARCTIC COMPACT 1/12 - 2/12 - 3/12 - 4/12 - 1/20 - 2/20 -

3/20 - 4/20 sono conformi alle seguenti Normative:

In ottemperanza alle Direttive 2006/42/CE, 2006/95/CE, 2004/108/CE.

EC DECLARATION OF CONFORMITY

We Ugolini spa, via dei Pioppi, 33 20090 Opera Milano ITALY declare, under our responsibility, that the apparatus COLD DRINK DISPENSER -

Trademark: UGOLINI S.p.A. - Manufacturer: UGOLINI S.p.A. - Model: ARCTIC COMPACT 1/12 - 2/12 - 3/12 - 4/12 - 1/20 - 2/20 - 3/20 - 4/20 are in

conformity with the following Standards:

Following the provisions of the Directives 2006/42/CE, 2006/95/CE, 2004/108/CE.

DECLARATION DE CONFORMITE CE

Nous Ugolini spa, via dei Pioppi, 33 20090 Opera Milano ITALY déclarons, sous notre responsabilité, que les appareil DISTRIBUTEUR REFROI-

DISSEUR DE BOISSONS - Marque: UGOLINI S.p.A. - Constructeur: UGOLINI S.p.A. - Modèle: ARCTIC COMPACT 1/12 - 2/12 - 3/12 - 4/12 - 1/20

- 2/20 - 3/20 - 4/20 sont conformes aux Normes suivantes:

Conformément aux Directives 2006/42/CE, 2006/95/CE, 2004/108/CE.

EG-ÜBEREINSTIMMUNGSERKLÄRUNG

Wir Ugolini spa, via dei Pioppi, 33 20090 Opera Milano ITALY erklären auf eigene Verantwortung, daß die Gerät KALTGETRÄNKE DISPENSER -

Marke: UGOLINI S.p.A. - Hersteller: UGOLINI S.p.A. - Modell : ARCTIC COMPACT 1/12 - 2/12 - 3/12 - 4/12 - 1/20 - 2/20 - 3/20 - 4/20 mit den fol-

genden Normen übereinstimmen:

Gemäß den EWG-Richtlinien 2006/42/CE, 2006/95/CE, 2004/108/CE.

DECLARACIÓN DE CONFORMIDAD CE

Nosotros Ugolini spa, via dei Pioppi, 33 20090 Opera Milano ITALY declararamos, bajo nuestra responsabilidad, que los aparato DISTRIBUIDOR

DE BEBIDAS FRIAS - Marca: UGOLINI S.p.A. - Fabricante: UGOLINI S.p.A. - Modelo: ARCTIC COMPACT 1/12 - 2/12 - 3/12 - 4/12 - 1/20 - 2/20 -

3/20 - 4/20 responden con las siguientes Normativas:

En cumplimiento de las Normas 2006/42/CE, 2006/95/CE, 2004/108/CE

-

EN ISO 12100-1 (2010)

EN ISO 12100-2 (2010)

EN60335-1 (2012)

EN60335-2-24 (2010)

EN60335-2-75 (2004) + A1 (2005) + A11 (2006) + A2 (2008) + A12 (2010)

-

EN62233:2008-11; EN62233:2009-04;

EN 55014 -1 (2006) + A1 (2009) + A2 (2011);

EN 55014-2 (1997) + A1 (2001) + A2 (2008)

EN 61000-3-2 (2006) + A1/A2 (2009); EN61000-3-3 (2008)

-

EN ISO 12100-1 (2010)

EN ISO 12100-2 (2010)

EN60335-1 (2012)

EN60335-2-24 (2010)

EN60335-2-75 (2004) + A1 (2005) + A11 (2006) + A2 (2008) + A12 (2010)

-

EN62233:2008-11; EN62233:2009-04;

EN 55014 -1 (2006) + A1 (2009) + A2 (2011);

EN 55014-2 (1997) + A1 (2001) + A2 (2008)

EN 61000-3-2 (2006) + A1/A2 (2009); EN61000-3-3 (2008)

-

EN ISO 12100-1 (2010)

EN ISO 12100-2 (2010)

EN60335-1 (2012)

EN60335-2-24 (2010)

EN60335-2-75 (2004) + A1 (2005) + A11 (2006) + A2 (2008) + A12 (2010)

-

EN62233:2008-11; EN62233:2009-04;

EN 55014 -1 (2006) + A1 (2009) + A2 (2011);

EN 55014-2 (1997) + A1 (2001) + A2 (2008)

EN 61000-3-2 (2006) + A1/A2 (2009); EN61000-3-3 (2008)

-

EN ISO 12100-1 (2010)

EN ISO 12100-2 (2010)

EN60335-1 (2012)

EN60335-2-24 (2010)

EN60335-2-75 (2004) + A1 (2005) + A11 (2006) + A2 (2008) + A12 (2010)

-

EN62233:2008-11; EN62233:2009-04;

EN 55014 -1 (2006) + A1 (2009) + A2 (2011);

EN 55014-2 (1997) + A1 (2001) + A2 (2008)

EN 61000-3-2 (2006) + A1/A2 (2009); EN61000-3-3 (2008)

-

EN ISO 12100-1 (2010)

EN ISO 12100-2 (2010)

EN60335-1 (2012)

EN60335-2-24 (2010)

EN60335-2-75 (2004) + A1 (2005) + A11 (2006) + A2 (2008) + A12 (2010)

-

EN62233:2008-11; EN62233:2009-04;

EN 55014 -1 (2006) + A1 (2009) + A2 (2011);

EN 55014-2 (1997) + A1 (2001) + A2 (2008)

EN 61000-3-2 (2006) + A1/A2 (2009); EN61000-3-3 (2008)

vedere targa dati sulla macchina

see data plate on the machine

voir la plaque sur l’appareil

siehe Dispenser Typenschild

ver la placa del distribuidor

Ugolini spa

L’Amministratore Delegato

(luogo ed anno di prod. - place and mfr. year - lieu et an de production

Produktionsort und Produktionsjahr - lugar y año de producción)

Page is loading ...

8

Arctic Compact 12-20

1 TECHNICAL CHARACTERISTICS

Specifications are subject to change without notice.

2 INTRODUCTION

It is necessary read all sections of this manual thoroughly to

familiarize yourself with all aspects of the unit.

Like all mechanical products, this machine will require cleaning

and maintenance. Besides, dispenser working can be

compromised by operator’s mistakes during disassembly and

cleaning. It is strongly recommended that personnel in charge of

the equipment’s daily operations, disassembly, cleaning,

sanitizing and assembly, go through these procedures in order

to be properly trained and to make sure that no

misunderstandings exist.

3 INSTALLATION

1 Remove the corrugate container and packing materials and

keep them for possible future use.

2 Inspect the uncrated unit for any possible damage. If

damage is found, call the delivering carrier immediately to file a

claim.

3 Install the unit on a counter top that will support the combi-

ned weight of dispenser and product bearing in mind what is

stated in the preceding point 1 IMPORTANT warning.

4 A minimum of 15 cm (6”) of free air space all around the unit

should be allowed to guarantee adequate ventilation.

5 Ensure that the legs are screwed tightly into the base of the

machine.

Replace the standard legs originally installed with the 100 mm

(4”) legs whenever they are provided with the unit.

6 Before plugging the unit in, check if the voltage is the same

as that indicated on the data plate. Plug the unit into a groun-

ded, protected single phase electrical supply according to the

applicable electrical codes and the specifications of your

machine. The electrical disconnect switch shall have a contact

separation in all poles , providing full disconnection under over

voltage category III conditions. Do not use extension cords.

7 The unit doesn’t come presanitized from the factory. Before

serving products, the dispenser must be disassembled, clea-

ned and sanitized according to this handbook instructions

(chapter 5.3 CLEANING AND SANITAZING PROCEDURES).

8 The appliances shall be installed only in places where

qualified people could control them.

4 TO OPERATE PROPERLY AND SAFELY

1 Do not operate the dispenser without reading this opera-

tor’s manual.

2 Do not operate the dispenser unless it is properly groun-

ded.

3 Do not use extension cords to connect the dispenser.

4 Do not operate the dispenser unless all panels are restrai-

ned with screws.

5 Do not obstruct air intake and discharge openings: 15 cm

(6”) minimum air space all around the dispenser.

6 Do not put objects or fingers in panels louvers and faucet

outlet.

7 Do not remove bowls, augers and panels for cleaning or

routine maintenance unless the dispenser is disconnected from

its power source.

1/12

1/20

2/12

2/20

3/12

3/20

4/12

4/20

Transparent removable bowls n 1 2 3 4

Capacity of each bowl, approx. l 12

20

12

20

12

20

12

20

Dimensions:

width cm 18 36 54 72

depth cm 47 47 47 47

height 12 lt

20 lt

cm 61

71

61

71

61

71

61

71

Net weight, approx. 12 lt

20 lt

kg 17

18

23

26

37

42

50

52

Gross weight, approx. 12 lt

20 lt

kg 19

20

26

29

40

45

55

56

Adjustable thermostats n 1 2 3 4

Hermetic compressor

Air-cooled condenser

Overload protector

Noise level lower than 70 dB (A)

IMPORTANT

Read electrical ratings written on the data plate of the

individual units; the data plate is adhered on the dispen-

sing side panel of the unit, just behind the drip tray (the

right side drip tray in multiple bowl models). The serial

number of the unit (preceded by the symbol #) is adhered

just below the right bowl. Data plate specifications will

always supersede the information in this manual.

IMPORTANT

When handling the machine never grasp it by the bowls.

The manufacturer refuses all responsibilities for possible

damages which may occur through incorrect handling.

ATTENTION

Failure to provide proper electrical ground according to

applicable electrical codes could result in serious shock

hazard.

IMPORTANT

Install the dispenser so that the plug is easily accessi-

ble.

ATTENTION

In case of damages, the power cord must be replaced by

qualified personnel only in order to prevent any shock

hazard.

9

8 The device must be positioned vertically at a height of min.

80cm / max . of 110cm from the floor.

9 Do not clean with sprinkling water.

10 This unit can work at a room temperature range between

+5° and +32°C.

11 Remind to use appropriate gloves during handling and pre-

paration of food.

12 Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

13 This appliance is intended to be used in household and

similar applications.

5 OPERATING PROCEDURES

1 Clean and sanitize the unit according to the instructions in

this manual. See chapter 5.3 CLEANING AND SANITIZING

PROCEDURES.

2 Fill the bowls with product to the maximum level mark. Do

not overfill.

The exact quantity of product (expressed as liters and gallons)

is shown by marks on the bowl.

3 In case of products to be diluted with water, potable water,

pour water into bowl first, then add correct quantity of product.

In case of natural squashes, it is advisable to strain them, in

order to prevent pulps from obstructing the faucet outlet.

4 Install the covers and check that they are correctly placed

over the bowls.

5 Set the control switches as shown in chapter

5.1 DESCRIPTION OF CONTROLS.

6 The dispenser must always run with the covers installed to

prevent a possible contamination of the product.

7 Always leave the dispenser on, as the refrigeration stops

automatically when the beverage reaches the dispensing tem-

perature. The mixing devices will continue to turn.

8 To maintain a high standard of flavour, keep refrigeration

and mixing devices on during the night when beverage is in the

bowl.

5. 1 DESCRIPTION OF CONTROLS

The dispenser is equipped with the power switch only. When it

is set to position I, the power is turned on both to mixing devices

and to refregeration.

5. 2 OPERATION HELPFUL HINTS

1 The length of time for cooling down the product is governed

by many variables, such as ambient temperature and beverage

initial temperature.

2 To shorten product cooling down time and increase pro-

ductivity, it is advisable to pre-chill the product to be used in the

dispenser.

3 To shorten product cooling down time and increase pro-

ductivity, the bowl should be refilled after the product level

drops lower than half and at the start of each day.

4 The dispenser must be able to emit heat.

In case it seems excessive, check that no heating source is

close to the unit and air flow through the slotted panels is not

obstructed by wall or boxes. Allow at least 15 cm (6”) of free

clearance all around the dispenser.

In any case if the product in the bowls is cold the unit is running

properly.

5 How to reset beverage temperature:to reset beverage tem-

perature please apply to a technician.

The proper temperature is preset at the factory.

6 To avoid the risk of falling, the area around the machine

should remain dry.

5. 3 CLEANING AND SANITIZING

PROCEDURES

Cleaning and sanitizing of the dispenser are recommended to

guarantee the conservation of the best product taste and the

highest unit efficiency. This section is a procedural guideline

only and is subject to the requirements of the local Health

Authorities.

Prior to the disassembly and cleaning, the machine must be

emptied of product.

5. 3. 1 DISASSEMBLY

1 Remove cover from the bowl.

2 Remove the empty bowl by lifting pulling lever (1) and its

front side (faucet side) up and off bowl gasket (see figure 1).

figure 1

3 Remove the bowl gasket.

4 Remove the pump impeller from its location.

5 Pinch tube faucet: push the dispensing handle (1) and

IMPORTANT

Operate the dispenser with food products only.

Fill with potable water.

IMPORTANT

This appliance is not intended for use by person (inclu-

ding children) with reduced physical sensory or mental

capabilities, or lack of experience and knowledge unless

they have been given supervision or instruction concer-

ning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not

play with the appliance.

ATTENTION

The access to the service area is restricted to persons

having safety/hygiene knowledge and practical expe-

rience on the appliance.

ATTENTION

Before any disassembly and/or cleaning procedure make

sure that the dispenser is disconnected from its power

source by unplugging it.

10

Arctic Compact 12-20

take the pinch tube off from its seat (2) (see figure 2).

figure 2

6 Gravity faucet: extract the piston and then remove the

dispensing handle (see figure 3).

figure 3

7 Slide drip tray out and empty it.

5. 3. 2 CLEANING

1 Prepare at least two gallons of a mild cleaning solution of

warm (45-60 °C 120-140 °F) potable water and dishwashing

detergent. Do not use abrasive detergent.

Important: if present, follow label directions, as too strong a

solution can cause parts damage, while too mild a solution will

not provide adequate cleaning.

2 Using a brush, suitable for the purpose, thoroughly clean all

disassembled parts in the cleaning solution.

3 Do not immerse the lighted top covers in liquid. Wash them

apart with the cleaning solution. Carefully clean their undersi-

des.

4 In the same manner clean the evaporator plates using a

soft bristle brush.

5 Rinse all cleaned parts with cool clean water.

5. 3. 3 SANITIZING

Sanitizing should be performed immediately prior to

starting the machine. Do not allow the unit to sit for

extended periods of time after sanitization.

1 Wash hands with a suitable antibacterial soap.

2 Prepare at least two gallons of a warm (45-60 °C 120-

140 °F) sanitizing solution (100 PPM available chlorine concen-

tration or 1 spoon of sodium hypoclorite diluted with two litres of

water) according to your local Health Codes and manufactu-

rer’s specifications.

3 Place the parts in the sanitizing solution for five minutes.

4 Do not immerse the lighted top covers in liquid. Carefully

wash their undersides with the sanitizing solution.

5 Place the sanitized parts on a clean dry surface to air dry.

6 Wipe clean all exterior surfaces of the unit. Do not use abra-

sive cleaner.

5. 3. 4 ASSEMBLY

1 Slide the drip tray into place.

2 Pinch tube faucet: push the dispensing handle (1) and

insert the pinch tube into its vertical seat in the bowl bottom(2).

Lightly pull the pinch tube end downwards til itl is well arranged

(3) (see figure 4).

figure 4

3 Gravity faucet: install the faucet handle and the piston with

IMPORTANT

Do not attempt to wash any machine components in a

dishwasher.

ATTENTION

Before any disassembly and/or cleaning procedure make

sure that the dispenser is disconnected from its power

source.

IMPORTANT

In order to prevent any damages to the dispenser use

only a detergent suitable with plastic parts.

ATTENTION

When cleaning the machine, do not allow excessive

amounts of water around the electrically operated com-

ponents of the unit. Electrical shock or damage to the

machine may result.

11

its gasket (see figure 5).

figure 5

4 Fit the bowl gasket to the evaporator. Note: the largest brim

of the gasket must face against the drip plate (see figure 6).

figure 6

5 Place bowl on the unit. Wet the gasket for ease of insertion.

Please take care that the hook on the backside of the bowl be

inserted properly in its seat on the upper drip plate. (see figure

7).

figure 7

6 Use fresh product to chase any remaining sanitizer from the

bowl(s). Drain this solution. Do not rinse out the machine.

5. 4 IN-PLACE SANITIZATION

The In-Place Sanitization prior to starting the machine may

be performed, if needed, only as further precaution, in

addition to the Disassembled Parts Sanitization described

before, but never in lieu of it.

1 Prepare two gallons of a warm (45-60°C, 120-140 °F) sani-

tizing solution (100 PPM available chlorine concentration or 1

spoon of sodium hypoclorite diluted with two litres of water)

according to your local Health Codes and manufacturer’s speci-

fications.

2 Pour the solution into the bowl(s).

3 Using a brush suitable for the purpose, wipe the solution on

all surfaces protruding above the solution-level and on the

underside of the top cover(s).

4 Install the top cover(s) and operate the unit. Allow the solu-

tion to agitate for about two minutes. Drain the solution out of

the bowl(s).

5 Use fresh product to chase any remaining sanitizer from the

bowl(s). Drain this solution. Do not rinse out the machine.

6 ROUTINE MAINTENANCE

Daily: inspect the machine for signs of product leaks past seals

and gaskets. If proper assembly does not stop leaks around

seals or gaskets, check for improper lubrication, worn or

damaged parts. Replace parts as needed with original spare

parts from the supplier.

6. 1 MAINTENANCE (TO BE CARRIED OUT BY

QUALIFIED SERVICE PERSONNEL ONLY)

Montly: clean all internal components, primarily the condenser,

using compressed air, in order to remove dust.

To clean these internal parts, unplug the unit.

Condenser fins are very sharp. Use extreme caution when cle-

aning.

IMPORTANT

Use gloves of a minimum PL 0-4 class (EN388).

ATTENTION

Verify the correct position of the cable before closing the

cabinet and before supplying electricity.

Page is loading ...

24

Arctic Compact 12-20

ELENCO RICAMBI

SPARE PARTS LIST

LISTE DES PIECES DE RECHANGE

ERSATZTEILLISTE

DESCRIPCION PIEZAS DE REPUESTO

25

1 22900-00100 Coperchio contenit. 20 It. 20 It bowl cover Couvercle réservoir 20 It Behälterdeckel 20 It Tapa contenedor 20 It

2 22900-00100 Coperchio contenit. 12 It. 12 It bowl cover Couvercle réservoir 12 It Behälterdeckel 12 It Tapa contenedor 12 It

3 22900-00010 Contenitore 12 It. 12 It bowl Réservoir 12 It Behälter 12 It Contenedor 12 It

4 22900-04810 Contenitore 20 It. 20 It bowl Réservoir 20 It Behälter 20 It Contenedor 20 It

5 22800-02600 Molla rubinetto Faucet spring Ressort du robinet Ventilfeder Muelle grifo

6 22800-17200 Guarnizione contenitore Bowl gasket Joint du réservoir Behälterdichtung Junta contenedor

7 33900-01201 Girante pompa Impeller Turbine de la pompe Pumpenrad Turbina bomba

8 22900-00700 Profilo di giunzione Plastic I-beam for con-

nection

Profil plastique de jonction Fugeband Perfil de union

9 22900-00600 Perno centrale Central pivot Pivot central Mittescharnierstift Pivote central

10 22040-00000 OR per perno centrale Central pivot OR OR du pivot central Mittescharnierstift OR OR del pivote central

11  Condensatore Capacitor Condensateur Kondensator Condensador

12 10554-45000 Clip Clip Clip Clip Clip

13 22800-21900 Pistone rubinetto Faucet piston Piston du robinet Kolben für Hahn Pistón del grifo

14 10028-02500 Guarnizione rubinetto Faucet gasket Joint du robinet Dichtung Junta del grifo

15 21703-00000 Gommino rubinetto Pinch tube Tuyau du robinet Ausgabeventilrohr Goma de grifo

16 10029-00020 Fotografia Picture Photo Dia Fotografia

17 22900-00500 Leva comando rubinetto Push handle Levier du robinet Ausgabe Placa de mando grifo

18 22900-00800 Coprirubinetto Faucet cover Couvercle du robinet Ventilkappe Cubre grifo

19 22900-00501 Leva comando rubinetto Push handle Levier de débit Zapfhebel Palanca de mando grifo

20 21087-00000 Termostato Thermostat Thermostat Thermostat Termostato

21 21125-00000 Interruttore Switch Interrupteur Schalter Interruptor

22 22800-05100 Protezione interruttore Switch cap Capuchon interrupteur Schalterabdeckung Protección interruptor

23 33900-01051 Puleggia con cuscinetto,

magnete e distanziale

Pulley, magnet and spacer

assembly

Ensemble poulie, aimant et

entretoise

Scheibe mit Kugellager,

Magnet und Büchse

Polea con magneto y

distancial

24 22900-03601 Cinghia Belt Courroie Reimen Correa

25 22800-02201 Puleggia per motore Driving pulley Poulie motrice Scheibe für Motor Polea motora

26 22800-04800 Staffa supporto motore Motor bracket Support du moteur Motorhaltebuegel Placa soporte motor

27  Motore ventilatore/pompa

per 1 vasca

Fan/pump motor for 1 bowl Moteur ventilateur/pompe

pour 1 réservoir

Lüftermotor/pumpe für 1

behälter

Motor ventilador/bomba

por 1 contenedor

27A  Motore ventilatore/pompa

per 2, 3, 4 vasche

Fan/pump motor for 2,3, 4

bowls

Moteur ventilateur/pompe

pour 2, 3,4 réservoir

Lüftermotor/pumpe für 2, 3,

4 ehälter

Motor ventilador/bomba

por 2, 3, 4 contenedor

28  Ventola Fan Hélice Lüfterflügel Aspas

29  Relé Relay Relais Start-Relais Relé

30  Salvamotore Overload protector Protége moteur Motorsicherung Guardamotor

31 22800-12700 Protezione passablocca-

cavo

Terminal block cover Protection borne Schutzkappe Protección pasacable

32  Passabloccacavo Terminal block with cable

clamp

Borne et fixage du câble Anschlußklemme m. Kabe-

leinfürung

Pasacable

33 33800-00803 Magnete motore per 1, 3

vasche

Motor magnet for 1, 3

bowls

Aimant du moteur pour 1, 3

réservoir

Motorrad für 1, 3 behälter Embrague magnetico por

1, 3 contenedor

34 22800-04800 Staffa supporto motore Motor bracket Support du moteur Motorhaltebuegel Placa soporte motor

35  Motore ventilatore/pompa

per 1, 3 vasche

Fan/pump motor for 1, 3

bowls

Moteur ventilateur/pompe

pour 1, 3 réservoir

Lüftermotor/pumpe für 1, 3

ehälter

Motor ventilador/bomba

por 1, 3 contenedor

36  Mobile Cabinet Carrosserie Gehaeuse Caja

37 22800-10000 Piedino Rubber leg Petit pied Justierfüße Pie nivelador

38  Pannello lato rubinetto Dispensing side panel Panneau côté robinet Front Panel lado grifo

39 22900-03700 Griglia cassetto raccogli-

gocce

Drip tray cover Couvercle tiroir égouttoir Tropfgitter Rejilla cajón

40 22900-03800 Cassetto raccogligocce Drip tray Tiroir égouttoir Tropfschale Cajón recoge-gotas

41 22900-00200 Tubo mandata 20 lt Spray tube for 20 l bowl Tuyau de la pompe 20 l Gekrumtes Sprudelrohr für

Behälter 20 l

Tubo de flujo para conte-

nedor 20 l

42 22900-04800 Contenitore 20 It. per

pompa

20 l bowl for pump Cuve 20 l pour pompe Behälter 20 l für Pumpe Contenedor 20 l para

bomba

43 22900-00201 Tubo mandata 12 lt Spray tube for 12 l bowl Tuyau de la pompe 12 l Gekrumtes Sprudelrohr für

Behälter 12 l

Tubo de flujo para conte-

nedor 12 l

44 22900-00000 Contenitore 12 It. per

pompa

12 l bowl for pump Cuve 12 l pour pompe Behälter 12 l für Pumpe Contenedor 12 l para

bomba

45 33900-01200 Girante pompa 50Hz Impeller 50Hz Turbine de la pompe 50Hz Pumpenrad 50Hz Turbina bomba 50Hz

45 33900-01204 Girante pompa 60Hz Impeller 60Hz Turbine de la pompe 60Hz Pumpenrad 60Hz Turbina bomba 60Hz

 Ordinare con sigla

riportata sul pezzo

Please order what printed

on piece

Mentionner indicatif

imprimé sur la pièce

Diese Teile bitte anhand der

aufgedruckten Nummern

bestellen

Pedir com la identificación

marcada en la pieza

/ Vedere tabella See table Voir tableau Siehe Tabelle Ver tabla

 

230-240V 50Hz 115V 60Hz 220V 60Hz 1/.. 2/.. 3/.. 4/..

11 22900-03050 22900-03051 22900-03052 28 - 22900-00402 22900-00402 22900-00402

27 22800-07600 33800-06901 22800-07600 36 22900-03200 22900-03201 22900-03202 22900-03203

27A 22900-03000 22900-03001 22900-03000 38 22900-03100 22900-03101 22900-03102 22900-03103

32 22800-05501 22800-05500 22800-05500

35 22800-04705 22800-04706 22800-04708

2405_99 V 1.8 14I22

26

Arctic Compact 12-20

SCHEMA ELETTRICO

WIRING DIAGRAM

SCHEMA ELECTRIQUE

SCHALTSCHEMA

ESQUEMA ELECTRICO

1/12-20 - 2/12-20 - 3/12-20

1 Interruttore Switch Interrupteur Schalter Interruptor

2-3-4 Termostato Thermostat Thermostat Thermostat Termostato

5-7 Pompa/agitatore Pump/mixer Pompe/brasseur Pumpe/Rührwerk Bomba/agitador

6 Compressore Compressor Compresseur Kompressor Motocompresor

4/12-20

1-2 Interruttore Switch Interrupteur Schalter Interruptor

3-4-5-6 Termostato Thermostat Thermostat Thermostat Termostato

7-9 Pompa/agitatore Pump/mixer Pompe/brasseur Pumpe/Rührwerk Bomba/agitador

8-10 Compressore Compressor Compresseur Kompressor Motocompresor

Page is loading ...

Ugolini ARCTIC COMPACT User manual

Ugolini ARCTIC COMPACT User manual

in other languages

Related papers

Other documents