Keystone K-Block Quarter Turn Position Indicator F792E IOM Owner's manual
- Type
- Owner's manual
7
5
6
4
2
8
1
29 mm
3
3
6
2
KEYSTONE K-BLOCK™ QUARTER-TURN POSITION INDICATOR - FIGURE 792E
MOUNTING AND INSTALLATION INSTRUCTIONS
WARNING
Before mounting, make sure that electrical
power to the cable assembly has been turned off.
Failure to do so may result in personnel injury.
MOUNTING THE POSITION INDICATOR
1. Fit proper driveshaft adaptor (or coupling)
(1) to actuator accessory drive, so that
flats are parallel to the transverse axis of
actuator in its closed position.
2. Assemble the K-BLOCK mounting kit (2)
to the actuator or bracket kit (3) using
screws (4) provided so that the indicator
arrow points 90° clockwise from the sensor
position with the actuator closed.
3. Assemble the K-BLOCK sensor (6) to
the mounting kit assembly (2), using slot
blanking plate (5) and screws (7).
4. Make sure the sensor (6) is 2 to 4mm from
the sensor puck.
5. Tighten the K-BLOCK sensor bolts (7) firmly.
(max. torque - 1Nm.).
CAUTION
Do not overtorque the sensor bolts.
Overtorquing the sensor bolts could damage
the K-BLOCK assembly.
6. Attach the matching plug and cable to the
K-BLOCK sensor.
Before installation these instructions must be fully read and understood
Emerson.com/FinalControl © 2017 Emerson. All Rights Reserved. VCIOM-01597-EN 17/03
Closed (lower)
Sensor screw
Open (upper)
Sensor screw
DIRECT MOUNTED VIEW BRACKET MOUNTED VIEW
2
TRANSVERSELY MOUNTED UNITS
Assembly as standard except
a. Remove Indicator cap (8), rotate 90° anti-
clockwise and re-fit with the indicator arrow
pointing at the sensor.
b. Changeover all yellow coloured plugs on
puck with the black plugs.
KEYSTONE K-BLOCK™ QUARTER-TURN POSITION INDICATOR - FIGURE 792E
MOUNTING AND INSTALLATION INSTRUCTIONS
ACTUATOR CLOSED - TRANSVERSE MODE
ACTUATOR CLOSED - NORMAL MODE
NOTES
Top sensor switch indicates open position.
Bottom sensor switch indicates close position.
Actuators rotate clockwise to close.
Please refer to diagrams.
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Keystone is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson
and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by
our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without
notice.
Emerson.com/FinalControl
-
1
-
2
Keystone K-Block Quarter Turn Position Indicator F792E IOM Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Keystone Pneumatic Actuators PremiAir IOM Owner's manual
-
Keystone Figure 89 pneumatic actuators Owner's manual
-
-
-
-
-
-
-
Keystone K-LOK® Series 36 and 37 High Performance Butterfly Valve Owner's manual
-
Other documents
-
Yarway Templow model 4300 IOM Owner's manual
-
KTM Hindle Series 300 Ultra-Seal two piece metal seated ball valves Owner's manual
-
-
Clarkson Model KS1 Severe Owner's manual
-
-
-
-
-
-