ADC AD-236 Installation guide

Brand: ADC

Model: AD-236

Category: Tumble dryers

Type: Installation guide

AD-236 Installation Manual

Phase 7

ADC Part No. 113215-12

AVERTISSEMENT: Assurez-vous de

bien suivre les instructions données dans

cette notice pour réduire au minimum le

risque d’incendie ou d’explosion ou pour

éviter tout dommage matériel, toute

blessure ou la mort.

—Ne pas entreposer ni utiliser d’essence

ni d’autres vapeurs ou liquides

inflammables à proximité de cet

appareil ou de tout autre appareil.

—QUE FAIRE SI VOUS SENTEZ UNE

ODEUR DE GAZ:

●

Ne pas tenter d’allumer d’appareils.

●

Ne touchez à aucun interrupteur. Ne

pas vous servir des téléphones se

trouvant dans le bâtiment.

●

Évacuez la pièce, le bâtiment ou la

zone.

●

Appelez immédiatement votre

fournisseur de gaz depuis un voisin.

Suivez les instructions du fournisseur.

●

Si vous ne pouvez rejoindre le

fournisseur de gaz, appelez le service

des incendies.

—L’installation et l’entretien doivent être

assurés par un installateur ou un

service d’entretien qualifié ou par le

fournisseur de gaz.

WARNING: For your safety the

information in this manual must be

followed to minimize the risk of fire or

explosion and to prevent property

damage, personal injury or death.

— Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS:

●

Do not try to light any appliance.

●

Do not touch any electrical switch;

do not use any phone in your

building.

●

Clear the room, building or area of

all occupants.

●

Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

●

If you cannot reach your gas

supplier, call the fire department.

— Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781 USA

Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447

e-mail: techsupport@amdry.com

www.adclaundry.com

We have tried to make this manual as complete as possible and hope you will find it useful. The manufacturer

reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and

material, and to change or discontinue models. The illustrations included in this manual may not depict your particular

dryer exactly.

IMPORTANT

For your convenience, log the following information:

DATE OF PURCHASE ________________________________________________________ MODEL NO. ______________

RESELLER’S NAME __________________________________________________________________________________

Serial Number(s) _____________________________________________________________________________________

____________________________________________________________________________________________________

Replacement parts can be obtained from your reseller or the ADC factory. When ordering replacement parts from the

factory, you can FAX your order to ADC at +1 (508) 678-9447 or telephone your order directly to the ADC Parts

Department at +1 (508) 678-9000. Please specify the dryer model number and serial number in addition to the

description and part number, so that your order is processed accurately and promptly.

These instructions are only valid if the following country code is on the appliance… If this code is not present on the

appliance, it is necessary to refer to the technical instructions which will provide the necessary information concerning

the modification of the appliance to the condition of use for the country.

In accordance with EN ISO 3166-1, the names of countries shall be represented by the following codes:

GB United Kingdom

IE Ireland

AD-236

Retain This Manual in a Safe Place for Future Reference

This product embodies advanced concepts in engineering, design, and safety. If this product is properly

maintained, it will provide many years of safe, efficient, and trouble free operation.

Only qualified technicians should service this equipment.

OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation

manual included with the dryer.

The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline

or other flammable vapors

and liquids in the vicinity of

this or any other appliance.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence

ni d’autres vapeurs ou liquides

inflammables à proximité de cet

appareil ou de tout autre appareil.

“IMPORTANT NOTE TO PURCHASER”

Information must be obtained from your local gas supplier on the

instructions to be followed if the user smells gas. These

instructions must be posted in a prominent location near the dryer.

IMPORTANT

YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND THE

GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS

ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING,

ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA

(Occupational Safety and Health Administration) STANDARDS.

WARNING

CHILDREN SHOULD NOT BE ALLOWED TO PLAY ON OR NEAR THE

DRYER(S).

CHILDREN

SHOULD BE SUPERVISED IF NEAR DRYERS IN OPERATION.

CAUTION

DRYERS SHOULD NEVER BE LEFT UNATTENDED WHILE IN OPERATION.

“Caution: Label all wires prior

to disconnection when servicing

controls. Wiring errors can cause

improper operation.”

«Attention: Au moment de l’entretien des commandes,

étiquetez tous les fils avant de les débrancher. Des

erreurs de câblage peuvent entraîner un fonctionnement

inadéquat et dangereux.»

Proposition 65

Use of this product could expose you to substances from fuel combustion

that contain chemicals known to the State of California to cause cancer,

birth defects and other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor,

plumber, or gasfitter qualified or licensed by the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

WARNING

IMPORTANT

PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/

or specified in the installation manual included with the dryer.

Dryer must not be installed or stored in an area where it

will be exposed to water or

weather.

The wiring diagram for the dryer is located in the front electrical control box area.

IMPORTANT

Dryer must be installed in a location/environment, which the ambient temperature

remains between 40° F (4.44° C) and 130° F (54.44° C).

FOR YOUR SAFETY

DO NOT DRY MOP HEADS IN THE DRYER.

DO NOT USE DRYER IN THE PRESENCE OF DRY CLEANING FUMES.

WARNING

UNDER NO CIRCUMSTANCES should the dryer door switches, lint drawer switch,

or heat safety circuit ever be disabled.

DO NOT MODIFY THIS APPLIANCE.

The dryer must never be operated with any of the back guards, outer tops, or service

panels removed. PERSONAL INJURY OR FIRE COULD RESULT.

DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN

IN PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED.

If a hi-limit switch trips, a service call is required to investigate the reason and resolve

the issue.

SECTION I

SAFETY PRECAUTIONS ............................................................................................................................. 2

SECTION II

SPECIFICATIONS.......................................................................................................................................... 5

SECTION III

INSTALLATION PROCEDURES ................................................................................................................ 7

A. Unpacking / Setting Up ........................................................................................................................ 7

B. Location Requirements......................................................................................................................... 8

C. Dryer Enclosure Requirements ............................................................................................................ 9

D. Fresh Air Supply Requirements ......................................................................................................... 10

E. Exhaust Requirements ........................................................................................................................ 11

F. Electrical Information......................................................................................................................... 14

G. Gas Information .................................................................................................................................. 18

H. Preparation for Operation / Start-Up ................................................................................................. 23

I. Preoperational Instructions................................................................................................................. 23

J. Shutdown Instructions ........................................................................................................................ 25

SECTION IV

SERVICE / PARTS INFORMATION ........................................................................................................ 26

A. Service ................................................................................................................................................. 26

B. Parts ..................................................................................................................................................... 26

SECTION V

WARRANTY INFORMATION ................................................................................................................... 27

A. Returning Warranty Cards .................................................................................................................. 27

B. Warranty............................................................................................................................................... 27

C. Returning Warranty Parts ................................................................................................................... 27

SECTION VI

ROUTINE MAINTENANCE....................................................................................................................... 29

A. Cleaning............................................................................................................................................... 29

B. Adjustments......................................................................................................................................... 30

C. Lubrication .......................................................................................................................................... 30

SECTION VII

DATA LABEL INFORMATION ................................................................................................................. 31

SECTION VIII

PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS .................... 32

SECTION IX

COIN PROGRAMMING ............................................................................................................................. 34

NON-COIN PROGRAMMING .................................................................................................................... 35

Table of Contents

2 American Dryer Corp. 113215- 12

SECTION I

SAFETY PRECAUTIONS

WARNING: For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage, personal injury, or loss of life.

WARNING: The dryer must never be operated with any of the back guards, outer tops, or

service panels removed. PERSONAL INJURY OR FIRE COULD RESULT.

1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

2. DO NOT spray aerosols in the vicinity of this appliance while it is in operation.

3. Purchaser/user should consult the local gas supplier for proper instructions to be followed in the event the

user smells gas. The instructions should be posted in a prominent location.

4. WHAT TO DO IF YOU SMELL GAS:

a. DO NOT try to light any appliance.

b. DO NOT touch any electrical switch.

c. DO NOT use any phone in your building.

d. Clear the room, building, or area of ALL occupants.

e. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

f. If you cannot reach your gas supplier, call the fire department.

5. Installation and service must be performed by a qualified installer, service agency, or gas supplier.

6. Dryer(s) must be exhausted to the outdoors.

7. Although ADC produces a very versatile dryer, there are some articles that, due to fabric composition or

cleaning method, should not be dried in it.

WARNING: Dry only water washed fabrics. DO NOT dry articles spotted or washed in dry cleaning

solvents, a combustible detergent, industrial chemicals, or “all purpose” cleaner.

EXPLOSION COULD RESULT.

WARNING: DO NOT dry rags or articles coated or contaminated with gasoline, kerosene, oil, paint,

or wax. EXPLOSION COULD RESULT.

WARNING: DO NOT dry mop heads. Contamination by wax or flammable solvents will create a

fire hazard.

113215- 12 www.adclaundry.com 3

WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or

similarly textured rubberlike materials. Drying in a heated basket (tumbler) may

damage plastics or rubber and may be a fire hazard.

8. The possible presence of residual quantities of aggressive or decomposed chemicals in the load may produce

damage to the machine and harmful fumes.

9. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ductwork,

and area around the back of the dryer. The frequency of inspection and cleaning can best be determined

from experience at each location.

WARNING: The collection of lint in the burner area and exhaust ductwork can create a potential fire

hazard.

10. For personal safety, the dryer must be electrically grounded in accordance with local codes or the National

Electrical Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the Canadian Electrical Codes

Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

NOTE: Failure to electrically ground the dryer will VOID THE WARRANTY.

11. UNDER NO CIRCUMSTANCES should the dryer door switches, lint drawer switch, or heat safety

circuit ever be disabled.

WARNING: PERSONAL INJURY OR FIRE COULD RESULT.

12. This dryer is not to be used in the presence of dry cleaning solvents or fumes.

13. Remove articles from the dryer as soon as the drying cycle has been completed.

WARNING: Articles left in the dryer after the drying and cooling cycles have been completed can

create a fire hazard.

14. READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE

DRYER.

15. For safety, proper operation, and optimum performances, the dryer must not be operated with a load less

than sixty-six percent (66%), 20 lb (18.14 kg) of its rated capacity.

WARNING: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND

THE GAS SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED

FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING,

ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER

OSHA (Occupational Safety and Health Administration) STANDARDS.

IMPORTANT: Dryer must be installed in a location/environment, which the ambient

temperature remains between 40° F (4.44° C) and 130° F (54.44° C).

4 American Dryer Corp. 113215- 12

WARNING: Disconnect power before resetting the hi-limit. The hi-limit is located on the top front of

the lint box. Press and release and the hi-limit will reset.

CE ONLY

IMPORTANT: This appliance must only be installed and operated in the country of destination

indicated on the dryer’s data plate. If the appliance is to be installed and operated in a

country other than the one indicated on the data plate, a data plate amendment must

be obtained from American Dryer Corporation.

IEC335 applies.

NOTES ____________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________________

113215- 12 www.adclaundry.com 5

MAXIMUM CAPACITY

(DRY WEIGHT) PER POCKET

30 lb

13.6 kg

TUMBLER DIAMETER 27-1/4”

69.22 cm

TUMBLER DEPTH 3 0”

76.2 cm

TUMBLER VOLUME

PER POCKET

10.1 cu ft

286 L

TUMBLER/DRIVE MOTOR

PER POCKET

1/2 hp

0.373 kW

BLOWER/FAN MOTOR

PER POCKET

1/2 hp

0.373 kW

DOOR OPENING

(DIAMETER)

21-1/2”

54.61 cm

DOOR SILL HEIGHT

TOP POCKET / BOTTOM POCKET

51-1/4” / 13-1/2”

130.2 cm / 34.3 cm

WATER CONNECTION N / A

DRYERS PER 20’/40’ CONTAINER 11 / 2 2

DRYERS PER 48’/53’ TRUCK 30 / 3 3

VOLTAGE AVAILABLE 120-240V 1,3ø 2,3w 50/60 Hz

APPROXIMATE NET WEIGHT 850 lb

385.5 kg

APPROXIMATE SHIPPING WEIGHT 900 lb

408.2 kg

AIRFLOW

PER POCKET

60 Hz

400 cfm

11.33 cmm

50 Hz

333 cfm

9.44 cmm

HEAT INPUT

PER POCKET

80,000 Btu/hr

20,160 kcal/hr

EXHAUST CONNECTION

(DIAMETER)

8”

20.32 cm

COMPRESSED AIR CONNECTION N / A

COMPRESSED AIR VOLUME N / A

INLET PIPE CONNECTION 3/4” M.N.P.T.

VOLTAGE AVAILABLE

N / A

APPROXIMATE NET WEIGHT

APPROXIMATE SHIPPING WEIGHT

AIRFLOW

PER POCKET

EXHAUST CONNECTION

(DIAMETER) PER POCKET

COMPRESSED AIR CONNECTION

COMPRESSED AIR VOLUME

OVEN SIZE

PER POCKET

kW Btu/hr

kcal/hr

VOLTAGE AVAILABLE

N / A

APPROXIMATE NET WEIGHT

APPROXIMATE SHIPPING WEIGHT

AIRFLOW

PER POCKET

STEAM CONSUMPTION

PER POCKET

OPERATING STEAM PRESSURE

EXHAUST CONNECTION

(DIAMETER) PER POCKET

COMPRESSED AIR CONNECTION

COMPRESSED AIR VOLUME

BOILER HORSEPOWER

(NORMAL LOAD) PER POCKET

SUPPLY CONNECTION

PER POCKET

RETURN CONNECTION

PER POCKET

Shaded areas are stated in metric equivalents 1/25/11

NOTE: ADC reserves the right to make changes in specifications at any time without notice or

obligation.

SECTION II

SPECIFICATIONS

GAS

ELECTRIC

STEAM

6 American Dryer Corp. 113215- 12

SPECIFICATIONS

NOTE: ADC reserves the right to make changes in specifications at any time without notice or

obligation.

113215- 12 www.adclaundry.com 7

SECTION III

INSTALLATION PROCEDURES

Installation should be performed by competent technicians in accordance with local and state codes. In the

absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1-

LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical

Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91

(Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General

Installation and Gas Plumbing) or Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION

(for Electrical Connections).

A. UNPACKING / SETTING UP

Remove protective shipping material (i.e., plastic wrap and/or optional shipping box) from dryer.

NOTE: The access keys for the service doors are included in the information packet shipped in the

basket (tumbler). These keys should be removed and put in a safe place, yet made

accessible because they will be needed throughout various phases in the installation of the

dryer.

Dryers are shipped with a coin box and coin box faceplate ONLY. The coin box lock is not included and

must be purchased elsewhere or the lock can be ordered as a parts order from the ADC Parts Department at

(508) 678-9000.

The dryer can be moved to its final location while still attached to the skid or with the skid removed. To unskid

the dryer, locate and remove the four (4) bolts securing the base of the dryer to the wooden skid. Two (2) are

at the rear of the base and two (2) are located in the front. Once the bolts are removed, slide the dryer off of the

skid.

With the skid removed, to make it easier to slide the dryer into its final position, slightly lower ALL the leveling

legs so that the dryer will slide on the legs instead of the base frame. The dryer is equipped with four (4) leveling

legs, one (1) at each corner of the dryer base.

8 American Dryer Corp. 113215- 12

B. LOCATION REQUIREMENTS

Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such

codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1 LATEST

EDITION, or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-

M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General

Installation and Gas Plumbing).

1. The dryer must be installed on a sound level floor capable of supporting its weight. Carpeting must be

removed from the floor area that the dryer is to rest on.

IMPORTANT: “The dryer must be installed on noncombustible floors only.”

2. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

3. The dryer is for use in noncombustible locations.

4. Provisions for adequate air supply must be provided as noted in this manual (refer to Fresh Air Supply

Requirements in Section D).

5. Clearance provisions must be made from combustible construction as noted in this manual (refer to Dryer

Enclosure Requirements in Section C).

6. Provisions must be made for adequate clearances for servicing and for operation as noted in this manual

(refer to Dryer Enclosure Requirements in Section C).

7. The dryer must be installed with a proper exhaust duct connection to the outside as noted in this manual

(refer to Exhaust Requirements in Section E).

8. The dryer must be located in an area where correct exhaust venting can be achieved as noted in this

manual (refer to Exhaust Requirements in Section E).

IMPORTANT: The dryer should be located where a minimum amount of exhaust duct will be

necessary.

9. The dryer must be installed with adequate clearance for air openings into the combustion chamber.

CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint build up.

IMPORTANT: The dryer must be installed in a location/environment, which the ambient

temperature remains between 40° F (4.44° C) and 130° F (54.44° C).

113215- 12 www.adclaundry.com 9

C. DRYER ENCLOSURE REQUIREMENTS

Bulkheads and partitions must be made of noncombustible materials and must be located a minimum of

12-inches (30.48 cm) above the dryer outer top, except along the front of the dryer which may be partially closed

in if desired. It is suggested that the dryer be positioned about 2 feet (0.61 meters) away from the nearest

obstruction, for ease of installation, maintenance, and service (to be measured from the back guard).

NOTE: Allowances must be made for opening the control door.

Dryers may be positioned sidewall to sidewall. However, a 1/16” (1.5875 mm) minimum allowance must be

made for the opening and closing of the control door. Refer to the illustration below for details.

NOTE: Air considerations are important for proper and efficient operation.

IMPORTANT: When fire sprinkler systems are located above the dryers, a minimum of 18-inches

(45.72 cm) above the dryer console (module) is required.

10 American Dryer Corp. 113215- 12

EXAMPLE: For a bank of four (4) dryers, a total make-up air opening of 6 square feet (0.55 square meters) is

required. Two (2) unrestricted openings measuring 18-inches by 24-inches (45.72 cm by 60.96 cm) are acceptable.

Allowances must be made for remote or constricting passageways or where dryers are located at excessive

altitudes or predominantly low pressure areas.

IMPORTANT: Make-up air must be provided from a source free of dry cleaning solvent fumes.

Make-up air that is contaminated by dry cleaning solvent fumes will result in

irreparable damage to the motors and other dryer components.

NOTE: Component failure due to dry cleaning solvent fumes will VOID THE WARRANTY.

D. FRESH AIR SUPPLY REQUIREMENTS

This appliance may only be installed in a room that meets the appropriate ventilation requirements specified in

the national installation regulations.

When the dryer is operating, it draws in room air, heats it, passes this air through the basket (tumbler), and

exhausts it out of the building. Therefore, the room air must be continually replenished from the outdoors. If the

make-up air is inadequate, drying time and drying efficiency will be adversely affected. Ignition problems and

sail switch “fluttering” problems may result, as well as premature motor failure from overheating.

Air supply (make-up air) must be given careful consideration to ensure proper performance of each dryer. An

unrestricted source of 800 cfm (22.66 cmm) is necessary for each dryer. As a general rule, an unrestricted air

entrance from the outdoors (atmosphere) of a minimum of 1-1/2 square feet (0.41 square meters) is required for

each dryer. The area must be enlarged if louvers or registers cover the openings. The dryer must be installed

with provisions for adequate combustion and make-up air supply.

To compensate for the use of registers or louvers used over the openings, this make-up air must be increased by

approximately thirty-three percent (33%). Make-up air openings should not be located in an area directly near

where exhaust vents exit the building.

is not necessary to have a separate make-up air opening for each dryer. Common make-up air openings are

acceptable. However, they must be set up in such a manner that the make-up air is distributed equally to ALL

the dryers.

A = 18” (45.72 cm)

B = 24” (60.96 cm)

113215- 12 www.adclaundry.com 11

E. EXHAUST REQUIREMENTS

Exhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork will

create excessive back pressure which results in slow drying, increased use of energy, overheating of the dryer,

and shut down of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler) hi-limit thermostats.

The dryer must be installed with a proper exhaust duct connection to the outside.

The design of the flue system shall be such that any condensate formed when operating the appliance from cold

shall either be retained and subsequently re-evaporated or discharged.

CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors.

CAUTION: IMPROPERLY SIZED OR INSTALLED EXHAUST DUCTWORK CAN

CREATE A POTENTIAL FIRE HAZARD.

The ductwork should be laid out in such a way that the ductwork travels as directly as possible to the outdoors

with as few turns as possible.

1. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust ductwork

should be laid out in such a way that the ductwork travels as directly as possible to the outdoors with as

few turns as possible. It is suggested that the use of 90° turns

be avoided; use 30° and/or 45° bends

instead. The radius of the elbows should preferably be 1-1/2 times the diameter of the duct. The shape

of the ductwork is not critical as long as the minimum cross-sectional area is provided.

IMPORTANT: Exhaust back pressure measured by a manometer/magnehelic in the exhaust duct

must be no less than 0 and must not exceed 0.3 in WC (0.74 mb) with both baskets

(tumblers) operating.

NOTE: It is recommended that exhaust or booster fans not be used in the exhaust ductwork system

except where necessary to maintain exhaust back pressure (in the exhaust duct) between zero

and 0.3 inch water column with both baskets (tumblers) operating. Where employed, booster

fans must not activate the dryer airflow proving switch (sail switch) when the dryer is not in

operation.

It is suggested that the ductwork from each dryer must not exceed 20 feet (6.1 meters) with no more than

two (2) elbows. If the ductwork exceeds 20 feet (6.1 meters) or has numerous elbows, the cross-sectional

area of the ductwork must be increased in proportion to the length or number of elbows in it.

IMPORTANT: For extended ductwork runs, the cross-sectional area of the ductwork can only be

increased to an extent. When the ductwork approaches the maximum limits as noted

in this manual, a professional heating, ventilating, and air-conditioning (HVAC) firm

should be consulted for proper venting information.

NOTE: As per the National Fuel Gas Code, “Exhaust ducts for Type 2 clothes dryers shall be

constructed of sheet metal or other noncombustible material. Such ducts shall be equivalent in

strength and corrosion resistance to ducts made of galvanized sheet steel not less than

0.0195 inches (26 gauge [0.5 mm]) thick.”

12 American Dryer Corp. 113215- 12

ALL ductwork should be smooth inside with no projections from sheet metal screws or other obstructions,

which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be

connected.

ALL ductwork joints must be taped to prevent moisture and lint from escaping into the

building. Inspection doors should be installed at strategic points in the exhaust ductwork for periodic

inspection and cleaning of lint from the ductwork.

NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible

materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).

The duct must be centered within this opening.

Outside Ductwork Protection

To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward should

be installed where the exhaust exits the building. If the ductwork travels vertically up through the roof, it

should be protected from the weather by using a 180° turn to point the opening downward. In either case,

allow at least twice the diameter of the duct between the duct opening and the nearest obstruction.

IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

2. Multiple Dryer (Common) Venting

If it

is not feasible to provide a separate exhaust duct for each dryer, ducts from individual dryers may be

channeled into a “common main duct.” The individual ducts should enter the bottom or the side of the main

duct at an angle not more than 45° in the direction of the airflow. The main duct should be tapered with

the diameter increasing before each individual 8-inch (20.32 cm) duct is added.

IMPORTANT: No more than eight (8) dryers should be connected to one (1) main common duct

(refer to the illustration on the following page).

The main duct may be any shape as long as the minimum cross-sectional area is provided. The illustration

on the following page shows the minimum cross-sectional area for multiple dryer venting. These figures

must be increased in proportion as the result of whatever changes or additions are made to this ductwork

run. Two examples are if ductwork length from last dryer to where duct exits the building exceeds limits

noted (20 feet [6.1 meters]) or, if ductwork runs from last dryer to where duct exits the building has more

than one (1) elbow (including outside protection).

113215- 12 www.adclaundry.com 13

NOTE: Refer to the illustration below for examples of multiple dryer (common) venting.

IMPORTANT: For extended ductwork runs, the cross-sectional area of the ductwork can only be

increased to an extent. When the ductwork approaches the maximum limits as noted

in this manual, a professional heating, ventilating, and air-conditioning (HVAC) firm

should be consulted for proper venting information.

IMPORTANT: Exhaust back pressure measured by a manometer/magnehelic in the exhaust duct

must be no less than 0 and must not exceed 0.3 in WC (0.74 mb) with both baskets

(tumblers) operating.

NOTE: It is recommended that exhaust or booster fans not be used in the exhaust ductwork system

except where necessary to maintain exhaust back pressure (in the exhaust duct) between zero

and 0.3 inch water column with both baskets (tumblers) operating. Where employed, booster

fans must not activate the dryer airflow proving switch (sail switch) when the dryer is not in

operation.

The ductwork should be smooth inside with no projections from sheet metal screws or other obstructions,

which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be

connected. ALL ductwork joints must be taped to prevent moisture and lint from escaping into the building.

Inspection doors should be installed at strategic points in the exhaust ductwork for periodic inspection and

cleaning of lint from the ductwork.

NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible

materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).

The duct must be centered within this opening.

To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward should

be installed where the exhaust exits the building. If the exhaust ductwork travels vertically up through the

roof, it should be protected from the weather by using a 180° turn to point the opening downward. In either

case, allow at least twice the diameter of the duct between the duct opening and nearest obstruction.

14 American Dryer Corp. 113215- 12

F. ELECTRICAL INFORMATION

1. Electrical Requirements

ALL electrical connections must be made by a properly licensed and competent electrician. This is to

ensure that the electrical installation is adequate and conforms to local and state regulations or codes. In the

absence of such codes,

ALL electrical connections, materials, and workmanship must conform to the

applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in

Canada, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

IMPORTANT: Failure to comply with these codes or ordinances, and/or the requirements

stipulated in this manual can result in personal injury or component failure.

NOTE: Component failure due to improper installation will VOID THE WARRANTY.

Each pocket should be connected to an independently protected branch circuit. The dryer must be

connected with copper wire only. DO NOT use aluminum wire, it could create a fire hazard. The

copper conductor wire/cable must be of proper ampacity and insulation in accordance with electric codes

for making ALL service connections.

NOTE: The use of aluminum wire will VOID THE WARRANTY.

IMPORTANT: A separate protected circuit must be provided to each pocket.

NOTE: An individual ground circuit must be provided to each dryer, do not daisy chain.

IMPORTANT: The dryer must be connected to the electric supply shown on the data label. In

the case of 208 VAC or 240 VAC, the supply voltage must match the electric service

specifications of the data label exactly.

IMPORTANT: The wire size must be properly sized to handle the related current.

WARNING: 208 VAC AND 240 VAC ARE NOT THE SAME. Any damage done to dryer

components due to improper voltage connections will automatically VOID THE

WARRANTY.

NOTE: Component failure due to improper voltage application will VOID THE WARRANTY.

NOTE: ADC reserves the right to make changes in specifications at any time without notice or

obligation.

113215- 12 www.adclaundry.com 15

GAS MODELS

ELECTRICAL SERVICE SPECIFICATIONS (PER POCKET)

IMPORTANT:

NOTES

: A.

208 VAC AND 240 VAC ARE

NOT THE SAME. When ordering,

specify exact voltage.

When fuses are used they must be dual element, time delay, current

limiting, class RK1 or RK5 ONLY. Calculate/determine correct fuse

value, by applying either local and/or National Electrical Codes to

listed appliance amp draw data.

Circuit breakers are thermal-magnetic (industrial) motor curve type

ONLY. For others, calculate/verify correct breaker size according to

appliance amp draw rating and type of breaker used.

Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

APPROX.

AMP DRAW

CIRCUIT

BREAKER

60 Hz 50 Hz

120 1ø 2 8.7 — 15

208 1ø 2 5.2 — 15

240 1ø 2 4.8 4.7 15

208 3ø 3 3.0 — 15

240 3ø 3 3.2 — 15

12/5/14

3. Grounding

A ground (earth) connection must be provided and installed in accordance with state and local codes. In

the absence of these codes, grounding must conform to applicable requirements of the National Electrical

Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation must conform to applicable

Canada Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The

ground connection may be to a proven earth ground at the location service panel.

For added personal safety, when possible, it is suggested that a separate ground wire (sized per local codes)

be connected from the ground connection of the dryer to a grounded cold water pipe. DO NOT ground to

a gas pipe or hot water pipe. The grounded cold water pipe must have metal-to-metal connection ALL

the way to the electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic,

rubber, or other insulating connectors, they must be jumped out with no. 4 copper wire and securely

clamped to bare metal at both ends.

IMPORTANT: For personal safety and proper operation, the dryer must be grounded.

Provisions are made for ground connection in each dryer at the electrical service connection area.

Electrical Service Specifications

16 American Dryer Corp. 113215- 12

4. Electrical Connections

A wiring diagram is located inside the control box for connection data.

If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail

(wire size must conform to rating of dryer), or the dryer can be hard wired directly to the service breaker

panel. In both cases, a strain relief must be installed where the wiring enters the dryer.

IMPORTANT: A separate protected circuit must be provided to each pocket.

Single-Phase (1ø) Hookup

The electrical input connections on

ALL single-phase (1ø) dryers are made into the junction box located at

the upper rear of the dryer. A separate circuit servicing each pocket must be provided.

Page is loading ...

ADC AD-236 Installation guide

Brand: ADC

Model: AD-236

Category: Tumble dryers

Type: Installation guide

Download PDF

report

ADC AD-236 Installation guide

ADC AD-236 Installation guide

Related papers

Other documents