eOUTIL AE1802-1 User guide

Brand: eOUTIL

Model: AE1802-1

Type: User guide

eOUTIL AE1802-1 Digital Battery Tester

The eOUTIL AE1802-1 is a versatile and user-friendly battery tester designed to provide accurate and comprehensive analysis of 12V batteries. With its advanced features, this device empowers you to assess the health, condition, and performance of your batteries, ensuring optimal performance and extending their lifespan.

Key Features:

5 Accurate Indexes: Analyze your battery's CCA Value, Resistance, State of Health, Voltage, and State of Charge, giving you a complete picture of its condition.
Wide Application Range: Compatible with various battery standards, including CCA, CA, BCI, MCA, SAE, GB, JIS, IEC, EN, and DIN, ensuring compatibility with a wide range of batteries.

eOUTIL AE1802-1 Digital Battery Tester

Key Features:

5 Accurate Indexes: Analyze your battery's CCA Value, Resistance, State of Health, Voltage, and State of Charge, giving you a complete picture of its condition.
Wide Application Range: Compatible with various battery standards, including CCA, CA, BCI, MCA, SAE, GB, JIS, IEC, EN, and DIN, ensuring compatibility with a wide range of batteries.

Digital Battery Tester (AE1802)

LCD Display

ESC Button

ENTER Button

Up Button

Down Button

Red

Black

Features:

Application range: 12V battery.

Analyze battery by 5 accurate indexes: CCA Value, Resistance, State of Health,

Voltage, and State of Charge.

Working scope:

Measuring voltage range: 6V-18V

Working temperature: 0 to 50

Measure standard mode:

CCA: 100-1700

CA:100-1700

BCI: 100-1700

MCA:100-1700

SAE: 100-1700

GB:30-200Ah

JIS: 26A17-245H52(100-1700)

IEC 100-1000

EN: 100-1700

DIN: 100-1000

Operation Procedure:

Clamp connection:

Power for the tester comes from the test battery.

For battery testing, place the tester clamps around the battery posts during testing.

Red clamp(+ positive) terminal and black clamp(- negative) terminal should be attached

to the corresponding battery terminal. For higher accuracy, both sides of each battery

clamp need to have a solid connection with the terminal post.

A partial connection may result in the “ ” displaying on the left of the screen or cause

the tester not to turn on at all. To correct, ensure the clamps are properly fastened.

Test Function selection:

Press “ENT” button to turn on the tester, the tester starts up in programming mode

showing the last entered value or in the CA(Cranking Amps) mode if no earlier value

entered.

Press “ ” or “ ” button to choose the measure standard mode you need.

Press "ENT" button to enter the measure standard mode you chose,

press “ ” or “ ” button to set the value, after input values are entered, press "ENT"

button to start testing mode, the bar graph and “TEST ON” will show.

To re-test, press the "ENT" button.

Press the "ESC" button to return to the previous menu or submenu.

To turn off the tester, remove clamps from terminals.

Note: If the voltage of the battery is too low, the “ ” icon will blink in the lower left

corner of the screen. Recharge the battery and test again.

Checking results

1.The index below the bar graph on the display screen shows the capacity of the battery

which has an indication from 0-100%.

If the bar graph displays less than 40%, it indicates the battery is broken or too old and

should be replaced.

Graph displays between 40%-60%, the battery is old, replacement should be considered.

Graph displays between 60%-80%, the battery is workable.

Graph displays between 80%-100%, the battery is in good condition.

2.Values display: take CCA for example.

First row is the entered CCA value for the battery.

Second row is the actual test CCA value of the battery.

Press “ ” button, the screen changes to the next values display.

First row is the the mΩ resistance of the battery.

Second row is SOH (State of Health) of the battery.

Press “ ” button again, the screen changes to the next values display.

First row is voltage of the battery.

Second row is SOC (State of Charge) of the battery.

Note 1: When choose JIS Measure Standard Mode, please refer to JIS-CCA

Comparison Index to set CCA value.

Note 2: When the testing values are different by using different “measure standard

modes”, please give priority to the CCA testing results.

Note 3: Vehicles must be turned off for more than half an hour before testing the battery.

A fresh fully-charged battery should be tested after removing it from the charger

for half an hour.

Note 4: The battery is designed for a single 12V battery. Do not use on a series

connected battery.

JIS translation table

Comparison table of DIN/EN

eOUTIL AE1802-1 User guide

Brand: eOUTIL

Model: AE1802-1

Type: User guide

eOUTIL AE1802-1 Digital Battery Tester

Key Features:

5 Accurate Indexes: Analyze your battery's CCA Value, Resistance, State of Health, Voltage, and State of Charge, giving you a complete picture of its condition.
Wide Application Range: Compatible with various battery standards, including CCA, CA, BCI, MCA, SAE, GB, JIS, IEC, EN, and DIN, ensuring compatibility with a wide range of batteries.

Download PDF

report

eOUTIL AE1802-1 User guide

eOUTIL AE1802-1 User guide

Other documents