Electrolux E40PV100FS Owner's manual

Brand: Electrolux

Model: E40PV100FS

Category: Cooker hoods

Type: Owner's manual

Electrolux E40PV100FS is a range hood that effectively removes cooking odors and grease from your kitchen. It features halogen lights for illuminating your cooking surface, a 3-speed fan that can be adjusted to your cooking needs, and dishwasher-safe grease filters for easy cleaning. With its sleek stainless steel finish, the E40PV100FS will complement any kitchen décor while providing powerful ventilation.

Use E_Care Guide

lnstaWWation Instructions

Ve n _ 1_oo d

READAND SAVETHESEINSTRUCTIONS

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

Read all instructions before installing the hood.

For your safety, please read and observe all safety instructions. This guide will

help you anticipate all installation connections.

[] [] [] [] [] [] [] [] [] [] [] [] [] [] []

For toll-free telephone support in the U.S. and Canada:

1=877= 4ELECTROLUX (1=877=435=3287)

For online support and Intemet product information:

www.electro_uxusa.com

[] [] [] [] [] []

@2006 Electrolux Home Products, Inc,

Post Office Box 212378, Augusta, Georgia 30917, USA

Al! rights reserve& Printed in the USA

TABIIII,,,,,,,,,,EOF CONTENTS

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

FindingInformation..............................................2

PleaseReadAndSaveThisGuide...................2

MakeA RecordForQuickReference................2

Questions...........................................................2

TableOfContents..............................................3

Safety.....................................................................4

ImportantSafetyInstructions.............................4

GeneralPrecautions..........................................5

Getting Started......................................................8

OperatingYourHood.........................................8

Careand Cleaning...............................................11

CleaningtheFiltersandHood..........................11

Installation...........................................................12

InstallationPlanning.........................................12

VarifyingPackageContents.............................13

InstallingtheDuctwork.....................................14

InstallingtheSupportSystem..........................15

ConnectingtheDecorativeFlue......................16

InstallingtheDuctCollar..................................16

MountingtheHoodtoSupportFrame.............17

InstallingtheElectrical.....................................17

ConnectingtheDuctwork.................................18

ReplacingtheBottomTrim..............................18

InstallingtheFilters..........................................19

Troubleshooting ................................................20

IfServiceis Required.......................................20

TroubleshootingGuide.....................................21

EnergySavingTips..........................................22

WarrantyInformation.........................................24

Safety Precautions

Do not attempt to install or operate your unit untie you have read the safety

precautions in this manual. Safety items throughout this manual are labeled with a

Warning or Caution based on the risk type,

Definitions

Z_ This is the safety alert symbol. It is used to alert you to potential personal injury

hazards. Obey all safety messages that follow this symbol to avoid possible injury

or death,

i¸iiii_iii!i_i_iil,i_iii!i_i_iil,i_iiiiiiiiiiiil_i__!!_!_ii!_i_!_!iiii_i_i!!i:i_i!_!!_!_i_!_:i_!_!i_i!_!_iiii_i_i!_!i_i!!!i_i!_!i_i!!!i_i!_!i_i!!!i_i!_!i_i!!!i_i!_!i_i!!!i_i{_i_i!i!!_!i_i_i!!_!_iii!i!_i!_ii_ii_!iii!!ii,!iiii_ilJ!iiii!i!ili!i!ili!i_ii!il,i_!i!,i_!i!,i_!i!,i_!i!,i_iiiii!i!iiiiiiiiii!iiiii:ii_i_i_i!i!iiii'i!!iiiii:ii!i:iiii:ii!i:iiii:ii!i:iiii:!i!ili'i_!_i!i!i!ii_i:iiiiii_iii!_iiiii_iiii!ii!,!:ii_!i:!:!i:!_!_!i_!i_i_ii!ii!i!!ii!ii!iii_i_J_:!i!_i_i_ii!ii!_!_!i!ii_i_ii_!_ii!i_i_i_:i_i_:i_i_:i_i%!_i_i!:!_!_ii!_i,_i_z!_!_z_!_i!_!_ii_!_!_!iii_ii!_ii!_ii!_i!_i_i_i_!_!_i!i!!_i_!_i_!_¸i_i_iii!!_!i_i_i_i!i_i_!i_!_!i_!_i_!_!i!_!_i%!_!_!_i!_!_i_i_!_ii_ii_ii_ii_!J_iii!_!_i_ii_i¸ii_i¸_!_!_ii!_!i_i!i!_ii!i!_ii!i!_ii!i!_ii!_!_!i!i!!_i_i_i_i_i_i_i_i!_i_i!i_i_!!i:ii_i!ii_i_!_!:i_ii_ii!:i_ii_ii!:i_ii_ii!:i_ii_ii!:i_ii_ii!:i_ii_ii!_!i_!!_!!_i_i_!:!_!i!:!,!_!:!iii_i,iiiiiiiiiiii!i!iiii!_i_iii_i!_i_i!i_i!_!_i_i_i!ii_i_i_ii!iiii_i¸iii!iii'Jiiii_ilili!i_iii!i_iii!i_iii!i_iii!i_iii!iii!iilliiiii_i!i_i_

SAFETYPRECAUTIONS

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] m []

ORERATIHG YOUR HOOD

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

The hood is operated using the slide controls under the front edge of the hood.

The light switch turns the halogen lights on and off.

PHLOT

LAMP

Figure 1

BLOWER

ON/OFF

SWHTCR

The blower on/off switch turns the blower on to the running

speed set by the blower speed control. The blower must be

turned on and off using this switch.

The blower speed control changes the running speed of the

blower (1-2-3).

The pilot lamp lights up whenever the blower is on.

Auto-Start Heat Sensing System

Your hood is equipped with an Auto-Start Heat Sensing

System thermostat. This thermostat is a device that will turn

on or speed up the blower if it senses excessive heat above

the cooking surface.

1 If blower is OFF - it turns blower ON to HIGH speed.

2 If blower is ON at a lower speed setting - it turns blower

up to HiGH speed.

When the temperature level drops to normal, the blower will

return to its original setting.

HALOGEN BULBS

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

This range hood requires four (4) halogen bulbs (Type MR16, 12V, 20W).

[] []

To change bulbs:

1 Loosen the ring nut by turning it counterclockwise.

2 Remove the bulb by pulling downward (DO NOT ROTATE).

3 Replace with a bulb of the same type (MR16, 12V, 20W). Do not touch replacement

bulb with bare hands.

Figure 2

FUSE REPIIII,,,,,,,,,ACEMENT

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

mFUGHTS FAiL TO OPERATE, DmSCONNECT POWER AT THE

SERVICE ENTRANCE. CHECK THE FUSE AND REPLACE mF

NECESSARY.

1 Remove grease filters.

2 Remove the electrical box support and open the fuse box.

3 Unscrew the cap from the fuse holder and remove the fuse.

4 Replace the fuse with the same size and amperage (5 x 20mm,

4 amp, 125 volt).

Figure 3

5 Reconnect power at the service entrance.

Care an Cleanin

ClIII,EANINGTHE FIL,,,,RSAND HOOD

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

Proper maintenance of the Range Hood will assure proper performance of the unit,

Grease Filters

The grease fi_ters should be cleaned frequently. Use a warm detergent solution,

Grease filters are dishwasher safe,

See "INSTALL FILTERS" section for removal and installation instructions.

Hood Cleaning

Stainless steel is one of the easiest materials to keep clean. Occasional care will

help preserve its fine appearance.

Cleaning tips:

1 Hot water with soap or detergent is all that is usually needed.

2 Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth

to avoid water marks.

3 For discolorations or deposits that persist, use a non-scratching household

cleanser or stainless steel polishing powder with a little water and a soft cloth.

4 For stubborn cases, use a plastic scouring pad or soft bristle brush together

with cleanser and water. Rub lightly in direction of polishing lines or "grain" of the

stainless finish. Avoid using too much pressure which may mar the surface.

5 DO NOT allow deposits to remain for long periods of time.

6 DO NOT use ordinary steel wool or steel brushes. Small bits of steel may

adhere to the surface causing rust.

7 DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds

to remain in contact with stainless steel for extended periods. Many of these

compounds contain chemicals which may be harmful. Rinse with water after

exposure and wipe dry with a clean cloth.

Painted surfaces should be cleaned with warm water and mild detergent only.

INSTAl,I,ATIONPLANNING

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

A qualified installer must complete the installation of this built-in appliance. Proper

installation is your responsibility.

Carefully check the location where the hood is to be installed. The hood should be

placed for convenient access. Make certain that electrical power can be provided

in the selected location.

Plan the installation so that all minimum clearances are met or exceeded.

Dimensions shown provide minimum clearances, unless otherwise noted.

Make certain that you have everything necessary to ensure a proper

installation before proceeding.

VERIFYPACKAGECONTENTS

[] [] [] [] [] [] [] [] [] [] [] [] [] [] []

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flue Assembly

1 - Support Frame

1 - Duct Collar

1 - Parts Bag containing:

8 - Washers ® 6.4

4 - Washers e 4.5

4 - Lag Bolts

8 - Mounting Screws (3.9 X 9.5mm Pan Head)

4 - Hex Nuts

1 - Installation Instructions

2 - Warranty Cards

[] [] [] []

4 REX NUTS

DECORATIVE

FLUE

SUPPORT

FRAME

8 WASHERS

_6.4

4 WASHERS

e4.5

8 MOUNTING SCREWS

(3.9 × 9.5ram Pan Head)

[] [] []

4 Lag Bolts

(6x7Omm)

DUCT COLLAR

Figure 4

INSTALLINGTHE DUCTWORK

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Decide where the ductwork will run between the hood and the outside. Figure 5.

2 A straight, short duct run will allow the hood to perform most efficiently.

3 Long duct runs, elbows, and transitions will reduce the performance of the hood. Use

as few of them as possible. Larger ducting may be required for best performance

with longer duct runs.

4 Install a roof or wall cap. Connect round metal ductwork to cap and work back

towards hood location. Use duct tape to seal the joints between ductwork

sections.

ROOF CAP

\ 8"

ROUND

DUCT

DECORATIVE

FLUE_

HOOD

24" to 30" ABOVE COOKING

SURFACE (See "Install Mounting

Bracket" section for mounting

restrictions).

Figure 5

J Jation

INSTAI,,,,,,,,,,I,,,,,,,,,,INGTHE SUPPORTSYSTEB

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 At hood location, install 2 x 4 cross framing between ceiling joists

using dimensions shown in Figure 6.

2 Finish the ceiling surface. Be sure to mark the location of the

ceiling joists and cross framing.

3 Measure the ceiling height and determine distance between the cook

top and bottom of hood.

4 Per the chart, adjust overall length of the support frame as shown in

Figure 7. Remove and reinstall (4) screws in the height adjustment

slots to achieve proper length. Install (4) additional 3.9 x 9.5mm

screws and 4.5 diameter washers from the Hardware Parts Bag.

CEILING

HEIGHT

8-FEET

9-FEET

10-FEET

(See note B)

SUPPORT FRAME HEIGHT ADJUSTMENT CHART

HOOD DISTAN¢ E ABOVE 3_' HiGH COOKTOP (SEE _OTE A)

24" J 25" J 26" J 27" I 28" I 29" I 30"

SUPPORT FRAME LENGTH

k _ F

25" 24" 23"

F k F

31"

I I

, , 46" 45" 44" 43"

DRYWALL

5 Secure the support frame to ceiling joists and cross framing with

(4) 6 x 70mm lag bolts and 6.4 diameter washers provided. Make

sure the bolts are driven into centers of joists and cross framing for

maximum strength. See Figure 8.

6 Run 2-wire plus ground electrical cable through the hole on top of

the support frame bracket. Cable length must extend at least 12"

below the bottom of the support frame. Secure cable to the support

frame with an appropriate cable connector.

CONNECTINGTHE DECORATIVEFLUE

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Secure the upper flue to the upper support frame with the mounting screws (3.9

x 9.5mm).

2 Insert the bower flue moving it completely towards the top and secure it temporarily

with retaining screws (3.9 x 9.5mm).

MOUNTING

SCREWS

(s.9 xg.5mm)

UPPER

FLUE

iNSERT THE LOWER FLUE

Figure 10

INSTAL,LINGTHE DUCTCOIIII,,,,,,,,,,I,,,,,,,,,,AR

m [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Fold the 2 tongues outwards.

2 Secure the discharge collar to the hood with (2) retaining screws

(3.90 x 9.5mm).

RETAiNiNG

SCREWS DISCHAR-

Figure 11

MOUNTINGTHE HOODTOSUPPORTFRAME

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Insert four (4) bolts through the top of the hood from the inside,

2 Use four (4) nuts and four (4) washers to secure hood to support frame.

[] []

INSTAL,LINGTHE EIIII,,,,,,,,,,ECTRICAIIII..........

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Remove the wiring box cover. Remove a knockout from the wiring

box.

2 Feed 6" of power cable through the knockout opening and secure

cable to the wiring box with an appropriate connector.

3 Make electrical connections. Connect white to white, black to black

and green to green.

4 Replace wiring box cover and screws. Check that wires are not

pinched between cover and box.

WiRiNG BOX COVER

Figure 13

[

CONNECTINGTHE DUCTWORK

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

LOWER

FLUE

8" ROUND

METAL

DUCT

RETAINING

SCREWS

Figure 14

1 Use 8" round metal duct to connect the discharge collar on the hood to

the ductwork above,

2 Use duct tape to make all joints secure and air tight,

3 Remove the two temporary retaining screws from the lower flue and set

it in place on the hood,

4 Secure decorative flue to hood with two mounting screws (3,9 x 9,5mm),

pan head mounting screws.

MOUNTING

Figure 15

R IIII,AClNGTHEBO TRIM

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 Remove the four (4) screws from the inside of the hood.

2 Remove the trim by pulling downward.

3 Slide the new trim upward into hood.

4 Replace the four screws inside hood.

Figure 16

INSTALLINGTHE FIL,,,,,,R(S)

[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []

1 To remove the grease filter, grip the latch and pull it down. This will disengage the

filters from the hood. Tilt the filter downward and remove.

2 To install the grease filter, align rear filter tabs with slots in the hood. Pull latch

tab down, push filter up into position and release the tab. Make sure the filter is

securely engaged after installation.

ii¸ii'_iiii¸¸_ili!i{i¸¸_i_:(i!_i_'_!!i_¸_''_'_'_!i_¸¸¸_i!i!!@i_iii!,!ii!,!iiiiill¸I!II¸:!I_!_:!I:!{!¸:iii_i!ii_i!ii_i!!i:_i:_:_:_!i!_!ii_i_ii_ii_ii_ii_ii_ii!i_i_%_!!!!_ii_!_!_¸i!iil¸iii:!ii_?ii!i:iii:iii:iii:i!i!!i:i!i!!_!i_!_!!!!i_!iiii!!i¸I¸@!@%i_iiii_!_iii¸?iiiii!i:_ii:i:iii!:¸i!{i_i!:_ii_!iii!i!iii!:i_!i!ili!i_:_i!i_:_i{iiii!@ili!i_iiiii{{!!ii:@!i':_i!i':_!ii_i¸iiii:i:!:!iiiii_',_ii_iiii(_ii_ii_i!i_i¸I¸ili:i_i!!:i!i!:i!i!iiiiiiiii%iii_ii(i(ili@ii¸i¸I¸ii!_ii!i!({i_iii!i!ii!£1:_@!i!_i!i!_i!ii!iiiiii!i_iiii¸i_ili¸i_ili¸I

iliii_!_!_i!_i!_i_!E!i!_i_i_i:ii!i!_ii_i!iii:_:_!i!!!_!i!!!!!_!_!_i_:i_i:i_!_i!_i_!_i_i!_!_ii!i_i_i_!:i_i_!:i_ii_iii_i_ii_!_!J_i_i_iii!i:_!_i!_i_!_i_!_i_!@!:!_i!i£{{_i_!_!_ii_!_!_ii_!_i_i_i_(_ii!i_!_ii_@:@_i_i_!_!_!_ii__i_ii_ii_ili_ii_ili_i!i_iiii_!ii_i_@@i!:_iii_i_i!_!_!_!_!!i:i_@_!_@_ii_!:i_i_!_i_i_!_!_i_!i:_!i_i_!_!!:_!_i__i_i::_@ii_i_i!_!_:_i_ii!_i_(@_!@_i_i!i!_i_!!!i_i@_ii:iJi!:i:_i!_!_(_!:!i_!_!_!i!_{_i!i_i_i_i_::i_::i_::i_!!!:!_i!!:_:_!ii!_ii!iii_!!_!_!i!i_

i i!ii!i i!ii!:!ii!ii!ii!ii!ii!ii!ii!ii!ii!iiiiiii i iii!i !ili i!iiiiii

GREASE

FILTERS

Figure 17