_'_'_4'a-=nl"Jm
SAFETY WARNINGS AND CAUTIONS:
• DO NOT st,u-d on tide i_oduct. You may Pal wkbh may cause person_ Injury.
• WEAR SAFETY GLASSIF_ AND GLOVE8 when cull_g _e ban(f_9 materiaL The
I_nd's may _rmp Which may ©a,Jsepersonal Injury.
- BECAREFUt.v_-_n ope, ingmorathan onedrawer.'[hepr_LL_tmaybecome
mslable and tip, which may cause personal injury or ixoduct damage.
• DO NOT mount lids product on a _,ck bed or any ether moving object. This may
cause personal thju_y el product damage.
• DO NOT step in the dmwem_ You maytog w_2t may cause personal injmy.
• Appropdatdy secure thispmdluct berate ram/lag Rwith a ferkJi11.
- DO NOT ahr this productin arp/manner. For e0_nnlale,do netwefd external Iockbare
or at_ eleot_l equipment. Thb may cause prod,_t damage or personal _u_.
• Lockthe drawers and deals before meting thispnodu_ "[he drawers or dears could
come open end make tim product unstable and tip, which may cause pemenar injuw
or product damage.
• The ma_imum weight for e_h drawer should be no more than 50 pounds.
• W_ght 5_I ollthe top of Ihe wolkbench is 1,000 poundeL ff the linnitise_,ceeded, the
I_odu_t oot_d col'apse and cause personal Injury or product damage.
....
letto SaUce PartsDrawingforfulllisle _,_,ervlce Parts I1_ I
HARDWARE:
(Some units may not Include all PARTS:
h_m_am} (Some units may not include all paris)
_)_ 14-10X 5,_ I-P_S:mw
_ 8 X 3'4 SIo_k_t_c_w
FRAME & SIDE ASSEMBLY:
NOTE: Betom ni/acldng the upper r'_s
(8) make sum f_a_the lances m
_oward the bot_m. Before;dlaCkinglira
lower mils (13)make sam tha_tk,, lances
are toward the top. (See picture beknv).
D.,_
/
:3. •
- A_ch a rail (B) _oeach side (D) usiag
1_o 14-10 x 5t8 hexse_w_ on e_ch e_L
Finger dghten. Repeat lhe procedure with
the _ernaining rails (B).
D
• Atto_ a center slJgf_t (C), to Ille ra_
(_ ueing t,vo 14-10 x 5/8 I've<scre_ at
e_achJ_et. Ftager 8ghten. Repe_t the
procedure with the ot_er support.
• The lances oe alloi'_ ra_s _heuld be
flush aga_lsl the _ange on 1hesides to
provide me proper spacing (18 1/2") for the
drawers. Square up the flame a=ernl_
andl_htel_ the ecrews. Rnger t]glffe_ Ihen
tighten 1/4 ken more or k_/que screws to
40 inch-pounds. DO NOT OVER
TIGNTEN.
TOPA68EMBLY:
(Depudent omModel)
MOTE:rlr IS RECOMMENDEDto have
another person kelp,,vfththis parrot ti_
assembly.
• Placethetop (A)ondean _ surtace.
(_e pacldng m_l_al ,Nil won:). Place
_rame assembly upside down on the lop.
Pos_on i_in a desired Ioca_on making
_wanaes forcan_rk_goroff_e_g _e
top to muiryour need_
• PomUon an attachment dp on the top
Altachrt_e_!
[
flange of the rail (1_ appro_ two inP-.hes
from the assembled Irame qpenbg end
arid r_a_k the hole Ioca_on. Repeat the
proc_lure unlg al four erld affachmer_!
di_ have been located.
- P'os_on attachment d'_ on both
front and back rails (B) at _e center
pear,one approx, two im:hes from the
cani_r supports. Mark the hole Ioca_o_rs_
- Ram eve fJheframe assembly and dn'llthe
ma[ked Ioca_ona fi8"dbmeter by 1/2"
deep in thetol x DONOr DRILL
I_:_IPER THAN lrZ'.
.. Repositk_ the frame _ssmnbl_ end
secure Ihe atta_im_ent dips udng one 8
x 3/4 slobd _,v per cllp.
Note: For tnodel no. ?0L_55070. Set
steel top (E) upside down. Place wood
top (A| in steel _op (E). Ma,'k lhe hoin
locations. Remove the wood _p (A) and
drill the madmd [oealk_s t,'8" _ameter
by ?/2" deep i: _e top. Place the wood
top (A_ back In Ele steel liop (E). P/_a
spacers (F) _ between the
steel lop and the weed top aUg]led with
Iw_es. Using #8 x 3/4" stated screws,
secure steel top and spacers (where
aec_ryl lethe wood top in tom
Iocal_ See graphics on next page,
3 4
