Metropolitan N7723-710 User manual

N7723-710
Metropolitan
Brand
Metropolitan
Model
N7723-710
Type
User manual

Metropolitan N7723-710 is a versatile lighting fixture that can be used to enhance the ambiance of any room. With its classic design and sturdy construction, it's a perfect choice for both residential and commercial applications. Installation is simple and straightforward, thanks to the included mounting hardware and detailed instructions. The fixture is compatible with three candelabra base bulbs up to 60 watts each, or CFL or LED equivalents. This allows for customization of the brightness and color temperature to suit your specific needs.

Metropolitan N7723-710 is a versatile lighting fixture that can be used to enhance the ambiance of any room. With its classic design and sturdy construction, it's a perfect choice for both residential and commercial applications. Installation is simple and straightforward, thanks to the included mounting hardware and detailed instructions. The fixture is compatible with three candelabra base bulbs up to 60 watts each, or CFL or LED equivalents. This allows for customization of the brightness and color temperature to suit your specific needs.

INSTALLATION INSTRUCTIONS
Item#N7723-710 (New. 02/11/2019)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box
and remove the old fixture including the mounting
hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clean area. Take care not to misplace any
small parts necessary for installation.
3. Remove the screw (C) and mounting plate (A).
4. Position the mounting plate (A) on the wall, and mark
location of the two mounting holes. Drill the holes on
the wall, and then insert the plastic anchors (E).
5. Attach the mounting plate (A) to the junction box using
mounting screws (B) (Size: #8-32N*L0.5”). The side of
the mounting plate marked “GND” must face out.
6. Secure the mounting plate (A) by inserting the wood
screws (F) through the holes on the mounting plate
into the plastic anchors (E).
CONNECTING THE WIRES (Fig. 2)
7. At this point, connect the electrical wires as shown in
Fig. 2, making sure that all wire connectors are
secured. If your outlet box has a ground wire (green or
bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to
the mounting plate (A) using the green screw provided.
After wires are connected, tuck them carefully inside
the junction box.
FINISHING THE INSTALLATION (Fig.1)
8. Place the candle covers (L) over the sockets (K) of the
fixture body.
9. Install (3) three candelabra base bulbs (M) up to 60
watts each or CFL or LED equivalent (not included) in
accordance with the fixture specification— DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
10. Place fixture body (D) over mounting plate (A) and
fasten with screws (C).
Your installation is now complete. Return power and test
the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-3057E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set#A-021-162430
-Mounting Plate
-Ground Screw
-Mounting Screw*2
Candle Cover# CCV24069P-710
E
A
F
C
D
L
M
K
B
  • Page 1 1

Metropolitan N7723-710 User manual

N7723-710
Metropolitan
Brand
Metropolitan
Model
N7723-710
Type
User manual

Metropolitan N7723-710 is a versatile lighting fixture that can be used to enhance the ambiance of any room. With its classic design and sturdy construction, it's a perfect choice for both residential and commercial applications. Installation is simple and straightforward, thanks to the included mounting hardware and detailed instructions. The fixture is compatible with three candelabra base bulbs up to 60 watts each, or CFL or LED equivalents. This allows for customization of the brightness and color temperature to suit your specific needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents