2. Robus
  3. R3EMPK4-PSU

Robus R3EMPK4-PSU Installation guide

  • Hello, I am your chat assistant. I have reviewed the provided document which is an installation guide for the ROBUS R3EMPK4-PSU emergency pack. The document details the wiring procedures for connecting the pack to light fittings, both with and without Swift connectors. I am ready to answer any questions you may have about the installation process or the device itself.
  • What is the purpose of this document?
    What is the first step when wiring with Swift connectors?
    What is the first step when wiring without Swift connectors?
    Where should the Emergency Pack cable labelled LED Driver Input be connected when wiring without Swift connectors?
Wiring Emergency
Pack R3EMPK4-PSU
into Fitting with
Swift
R3EMPK4-PSU & Fitting with Swift
Driver
Fitting Inline
Connector
Driver
(Output)
Inline
Connector
Driver
(Input)
Female Swift
Connector
Driver
(Input) Male
Swift
Connector
Emergency
Pack
(Permanent
and Switch
AC) Male
Swift
Connector
Emergency
Pack (LED
Driver Input)
Female Swift
Connector
LED
Indicator Emergency
Pack
Emergency
Pack (Output
to Lamp)
Inline
Connector
Emergency Pack
(Driver DC
Output) Inline
Connector
Remove the Female Swift Connector from the Driver Input and connect it
to the Male Swift Connector of the Emergency Pack labelled ‘Permanent
and Switched AC’
R3EMPK4-PSU & Fitting with Swift
Female Swift
Connector
Emergency
Pack
(Permanent
and Switch
AC) Male
Swift
Connector
Driver
Connect the Female Swift Connector of the Emergency Pack labelled ‘LED
Driver Input’ to the Driver Male Swift Connector
R3EMPK4-PSU & Fitting with Swift
Emergency
Pack (LED
Driver Input)
Female Swift
Connector
Driver Male
Swift
Connector
Disconnect the Inline Connector between the Driver and the Fitting
R3EMPK4-PSU & Fitting with Swift
Connect the Inline Connector of the Fitting to the Inline Connector of the
Emergency Pack labelled ‘Output to Lamp’
R3EMPK4-PSU & Fitting with Swift
Connect the Inline Connector of the Driver Output to the Inline Connector
of the Emergency Pack Driver Output labelled ‘Driver DC Output’
R3EMPK4-PSU & Fitting with Swift
Wiring Emergency
Pack R3EMPK4-PSU
into Fitting without
Swift
R3EMPK4-PSU & Fitting without Swift
Driver
Fitting Inline
Connector
Driver
(Output)
Inline
Connector
Emergency
Pack
(Permanent
and Switch
AC) Male
Swift
Connector
Emergency
Pack (LED
Driver Input)
Female Swift
Connector
LED
Indicator Emergency
Pack
Emergency
Pack (Output
to Lamp)
Inline
Connector
Emergency Pack
(Driver DC
Output) Inline
Connector
Remove Female Swift Connector from the Emergency Pack cable labelled
‘LED Driver Input’
R3EMPK4-PSU & Fitting without Swift
Emergency
Pack (LED
Driver Input)
Female Swift
Connector
Connect the removed Female Swift Connector to the Male Swift Connector
of the Emergency Pack labelled ‘Permanent and Switched AC’
R3EMPK4-PSU & Fitting without Swift
Female Swift
Connector
Emergency
Pack
(Permanent
and Switch
AC) Male
Swift
Connector
Driver
Connect the Emergency Pack cable labelled ‘LED Driver Input’ to Input side
of the Driver
R3EMPK4-PSU & Fitting without Swift
Disconnect the Inline Connector between the Driver and the Fitting
R3EMPK4-PSU & Fitting without Swift
Connect the Inline Connector of the Fitting to the Inline Connector of the
Emergency Pack labelled ‘Output to Lamp’
R3EMPK4-PSU & Fitting without Swift
Connect the Inline Connector of the Driver Output to the Inline Connector
of the Emergency Pack Driver Output labelled ‘Driver DC Output’
R3EMPK4-PSU & Fitting without Swift
/