Harvest TEC 200RBC User manual

H2O Sensor-Owners-18-Imp&Metric

6/22

Owner’s Manual

H2O Sensor - Model 200

& 200DM

Round Baler Precision Moisture Sensing Kit

Forage Harvester

2

DECLARATION OF INCORPORATION

MANUFACTURER: Harvest Tec LLC.

2821 Harvey St.

P.O. Box 63

Hudson, WI 54016, U.S.A.

REPRESENTATIVE ESTABLISHED IN COMMUNITY: Profitable Farming Company

Middle Barlington, Roborough

Winkleigh, Devon, EX19 8AG

ENGLAND

The person above certifies and declares that:

VIRTUAL MACHINE: Equipment mounted on a farm press to monitor moisture.

MODEL: H2O Sensor-Owners-18-Imp&Metric

BRAND: Harvest Tec

SERIAL NUMBER:

This Harvest Tec moisture system meets the Directive 2006/42/EC of the European Parliment and the

Council of 17 May 2006 and other applicable European Directives including Directive 2014/53/EU on

the Radio Equipment Directive and 2014/30/EU.

The Harvest Tec moisture system will be turned on after being installed on a farm press which has

been declard in conformity with the Machinery Directive.

Person in the community authorized to provide information on the partly completed machinery and

making this statement:

Richard Snell, President, Profitable Farming Company

Signed on May 21, 2011: Middle Barlington, Roborough

Winkleigh, Devon, EX19 8AG

ENGLAND

3

H2O Moisture Owner’s Manual Table of Contents

Page

Introduction

3

Tools Needed

3

Moisture Disc Installation Reference Chart

4

Installation of Applicator

5-12

Installation of Moisture Sensor Pads and Discs

5-11

Option A

5

Option B

6

Option C

7

Option D

8

Option E

9

Option F

10

Option G

11

End of Bale Sensor Installation

12

Control Box Installation

12

200RB Dye Marker Installation (Optional

13

Wiring Diagram

14

Downloading H2O App

15

Screen Definitions

15

Main Screen

15

Settings Screen

15

Operation

16-18

Reading Moisture

16

Moisture Range

16

Fixed Chamber Balers Only

17

Dye Sprayer System

18

Dye Sprayer Override

18

H2O Firmware Update through App

19

Troubleshooting

20

Pin Outs

21-22

Parts Breakdown

22-24

Installation Option A

22

Installation Option B → G

23

Fixed Chamber End of Bale Sensor Kit

23

Precision Moisture Dye Marker

24

Notes

25-26

Warranty Statement

27

Introduction

Congratulations and thank you for purchasing a Harvest Tec H2O Moisture Sensing Kit Model 200 system.

Please read this manual carefully to ensure correct steps are taken to attach the system to the baler. This

system is designed to read moisture at levels of 6-60%.

Requirements

The app will support operation of the current operating system and one previous version for both Apple and

Android devices.

Tools Needed

SAE wrench set

Hammer

Drill bit set

Standard screw driver

Measuring tape

Center punch

Side cutter

SAE socket set

4

Moisture Disc Installation Reference Chart

Use this chart to identify the correct moisture disc installation instructions for each baler model.

Baler Make

Baler Model

Install

Option

AGCO

5134, 5415, 550

B

5446, 5446 Silage, 5456, 5545, 5545 Silage, 5546, 5546 Silage, 5556, 5556 Silage,

2745, 2746, 2746A, 2756A, 2766

E

2846, 2846A, 2856, 2856A, 2946, 2946A, 2956, 2956A

F

CaseIH

8400 Series, RB444, RBX 442, 443, 451, 461, 561

B

RB 454,464, RBX 452, 453, 462, 463

B

RB 554, 564, RBX 552, 553, 562, 563

B

RB 455, 465, 560, 565

A

RB455A Utility Baler

A

Challenger

RB 34, 44, 45, 452

B

RB 46, 56

E

RB 453, 453A, 463, 463A, 563, 563A, RB 56C, RB56CA

F

Claas

Rollant Fixed Chamber, Variant 280 & 360

B

Hesston

500 Series: 530, 540, 545, 550, 555S, 555T, 560, 565A, 565T, 700 Series - 730, 740,

745, 5400, 5500, 5600, 5800, Series Fixed Chamber, 814 Fixed Chamber

B

800 Series - 845, 846A, 855, 856, 900 Series - 946, 955, 956

E

John Deere

430, 510, 530

B

435, 455, 465, 535, 545, 565, 446, 456, 466, 546, 566, 447, 457, 467, 547, 557, 567

C

448, 458, 468, 558, 568, 449, 459, 459E, 469, 559, 569, 440, 450, 460, 550, 560

C

440, 450, 460, 550, 560 w/HC2

C

960, 990

G

582 Silage Special, 854

D

C451R, V451R, V461R

C

Krone

Round Pack Fixed Chamber, 1250, 1250 Multi-Cut, 1550, 1550 Multi-Cut, KR 125,

F130, Vario Pack, 1510, 1810, Comprima Series

B

Kubota

BV4160, BV4180, BV4580, BV5160

A

Kuhn

VB 2160, 2190, VB 2255, 2260, 2265, 2285, 2295, FB119, 2130

B

Kuhn

VB3160, VB3190, VBP3165

A

McHale

V660, F540, F550, F560, Fusion Balers

B

Massey

Ferguson

1734, 1745, 1746, 1756

B

2745, 2746, 2746A, 2756A, 2766

E

2846, 2846A, 2856, 2856A, 2946, 2946A, 2956, 2956A

F

RB4100V

B

New Holland

544, 548, 564, 630, 634, 638

B

640, 644, 648, 650, 658 ,660, 664, 668, 678, 688

B

BR 7060, 7070

B

BR 7080, 7090

B

BR 730, 730A, 7050

B

BR 740, 740A, 750, 750A

B

BR 770, 770A, 780, 780A

B

Roll Belt 450, 460, 550, 560, 565

A

BR450 Utility Baler

A

RF 440, 450 Fixed Chamber

C

New Idea

4800 Series Fixed, 6343, 6344, 6345, 6364, 6365, 6454, 6464, 6465

B

Vermeer

404, 504 Series 1 Pro

B

404, 504 Series 2 Pro

B

604 Series 3 Pro

B

504, 505 J, K, M, N, Series, Rebel Series, XL Series

B

604M, 605M, 604N, 605N, 504R

B

Vicon

RV 1601, 1901, 2160, 2190

B

Welger

RP Fixed Chamber 202, 220, 235, 245, 415, 420, 445, 520, 535

B

5

Option A – Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. Open rear tail gate of baler and lock in the up position. Refer to baler manual to lock door open.

2. Remove bale shaping discs on each side of chamber.

3. Place plastic isolator (006-4641FX) in the same spot that the shaping disc had been. There should be a

hole in the baler that matches up with the hole in the plastic isolator, this hole will need to be drilled out to

3/4" (19mm). If there is not a hole, use the isolator as a template and mark the hole. Center punch the hole

and drill it to 3/4" (19mm). Note: before drilling make sure you are not drilling into sensitive equipment on

the outside of the baler). Repeat for other side of the baler.

4. Insert plastic bushing (006-4641G) from the outside of baler. Make sure it is flush with the outside of the

baler frame. Go to the inside of the baler and mark amount that protrudes into the chamber. Remove and

cut off excess material. Repeat for other side.

5. Using the 4” carriage bolt slide the parts on in following order: metal disc (001-4641HX), plastic isolator

(006-4641FX) and shortened plastic bushing (006-4641G).

6. Insert disc assembly into 3/4” (19mm) hole from inside of bale chamber. Secure to outside of baler by

attaching to the protruding carriage bolt in the following order: small isolator (006-4641I), 1/2” D shaped

washer, 1/2” lock washer, 1/2” nut. Tighten down and repeat for the other side. Make sure no part of the

bolt or hardware makes contact with the frame of baler-no metal to metal. Trim 006-4641I to fit.

7. Route moisture harness (006-2470B from processor down to the carriage bolt on each side. Make sure it

does not come in contact with any moving parts. Secure with cable ties.

8. Attach moisture cable to moisture carriage bolt by placing items in the following order: 1/2” D shaped

washer, Ring terminal of moisture harness (006-2470B), second 1/2” D washer, 1/2” lock washer, 1/2” nut.

Tighten down and repeat for other side. Make sure none of the hardware contacts the frame of baler.

6

Option B - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. If your baler is equipped with bale shaping pads, remove disc and use existing hole (may need to be drilled

larger, 3/4" (19mm) to install new moisture sensing discs.

2. If your baler is not equipped with bale shaping pads you will need to drill a hole in the chamber directly

behind and above the starting roll (Figure 1).

3. The mounting hole will be 3/4" (19mm) in diameter. Use a plastic pad (006-4641F) and place it into the

baler to use as a template. The bottom edge of the pad will be placed 1” (25mm) up from starting roll and

2” (51mm) from the back of the bale chamber (Figure 1).

4. Locate the 006-4641G (a) piece, this will need to be cut down to size. Use the already machined line in the

bushing to cut off the small piece shown above 006-4641G (b). Part 006-4641I may also need to be

trimmed to fit.

5. Depending on the baler the bolt may need to be trimmed for proper fit.

6. Tighten all of the hardware to 50 ft/lbs (68 N/m).

7. Make sure that the plastic pad is protecting all metal surfaces of the disc from touching baler.

8. Run the moisture wire harness (006-2470B) to each disc securing with cable ties.

2” from back of chamber

(51mm)

1” from top of roll

(25mm)

Figure 1

006-4641G (a)

006-4641G (b)

006-4641I

006-2470B

006-4641F

006-4641H

7

Option C - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. Both moisture discs (006-4641H) will need to be cut along the serrated line (A) shown on Figure 1. Only

cut on the line shown on Figure 1, do not cut the other line.

2. The plastic pad (006-4641F) will also need to be cut 1/4" (7mm) longer than the back of the disc.

3. Using the cut disc as a pattern, mark and drill a 3/4" (19mm) hole in the side of the bale chamber. The disc

will need to be placed on the baler 1” (25mm) up from bottom and 1/4" (7mm) in from the back of the

chamber (Figure 2).

4. Make sure that plastic pad is protecting all metal surfaces of disc from touching baler.

5. Run the moisture wire harness (006-2470B) to each disc securing with cable ties.

6. On some balers the bolt may need to be trimmed for proper fit.

7. Tighten all hardware to 50 ft/lbs (68 N/m).

8. Apply silicone over nuts and washers.

Figure 2

1” from Bottom

(25mm)

1/4" in from

back of baler

(7mm)

006-2470B

006-4641I

006-4641G

006-4641F

006-4641H

A

Figure 1

8

Option D - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. The moisture discs (006-4641H) will both need to be cut on line A. (Figure 1) One disc will need to be cut

on line B and one disc on line C.

2. The plastic pad (006-4641F) will also need to be cut 1/4" longer than the back of the disc.

3. Bevel all sides of the cut discs to allow the smooth travel of crop over them.

4. The mounting hole will be 3/4" (19mm) in diameter. The disc will need to be placed on the baler lining up

the center of the bolt with the location 2” (51mm) up from bottom and 2” in from the back of the chamber.

(Figure 2)

5. Make sure that plastic pad is protecting all metal surfaces of disc from touching baler.

6. Run the moisture wire harness (006-2470B) to each disc, securing with cable ties.

7. On some balers the bolt may need to be trimmed for proper fit.

8. Tighten all hardware to 50 ft/lbs (68 N/m).

9. Apply silicone over nuts and washers.

Figure 2

006-2470B

006-4641I

006-4641G

006-4641F

006-4641H

A

B

C

Figure 1

9

Option E - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. If your baler is equipped with bale shaping pads, remove pads and use existing hole (may need to be

drilled larger) to install new moisture sensing discs.

2. If your baler is not equipped with bale shaping pads you will need to drill a hole in the chamber directly

behind and above the starting roll (Figure 1).

3. You will need to remove the main chain assembly to install the disk on the right side of baler (when facing

front of baler) Figure 2.

4. The hole size is 3/4” (19mm) diameter. Before drilling the hole make sure hole is accessible from opposite

side of chamber to tighten down mounting hardware and to install moisture harness (Figure 3).

5. Locate the 006-4641G. The piece will need to be cut down to size.

6. Use the already machined line in the bushing to cut off the small piece shown above.

7. Depending on the baler the bolt may need to be trimmed for proper fit.

8. Tighten all of the hardware to 50 ft/lbs (68 N/m).

9. Make sure that the plastic pad is protecting all metal surfaces of the disc from touching baler (Figure 4)

10. Run the moisture wire harness (006-2470B) to each disc securing with cable ties.

11. Apply silicone over nuts and washers.

Figure 3

Figure 4

Figure 1

Figure 2

006-4641I

006-4641H

006-4641F

006-4641G

006-2470B

10

Option F - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

1. Both moisture discs (006-4641H) will need to be cut along the serrated line (A) shown on Figure 1.

Measure from the laser etched line (B) 1 3/4" (45mm) on both side. Mark and cut the disc. A completed

disc in shown to the right.

2. The plastic pad (006-4641F) will also need to be cut 1/4" (7mm) larger than the steel disc.

3. Bevel all sides of the cut discs to allow the smooth travel of crop over them.

4. Mark a line 1 1/2” (38mm) up and 3 1/2” (89mm) over from point (D). Drill a 3/4” hole at the point (E).

Repeat for the opposite side.

5. Locate the 006-4641G. The piece will need to be cut down to size. Use the already machined line in the

bushing to cut off the small piece shown above.

6. Depending on the baler the bolt may need to be trimmed for proper fit.

7. Tighten all of the hardware to 50 ft/lbs.

8. Make sure that the plastic pad is protecting all metal surfaces of the disc from touching baler.

9. Run the moisture wire harness (006-2470B) to each disc securing with cable ties.

10. Apply silicone over nuts and washers.

A

C

B

Figure 1

Figure 2

D

E

006-4641G

006-2470B

006-4641I

006-4641H

006-4641F

11

Option G - Installation of Moisture Sensor Pads and Discs

*Refer to Moisture Disc Installation Reference Chart to locate correct install option

4. With the baler door open measure 5 1/8” toward top of baler from the point shown in figure 1. Drill a 3/4”

(19mm) hole to mount moisture disc as shown in figure 2.

5. Use plastic pad (006-4641F) and place it into the baler to use as a template. The bottom edge of the pad

will be placed 2” (51mm) up from bottom of sheet metal on door and starting roll and 1” (25mm) back from

sheet metal seam in figure 2.

6. Locate part 006-4641G, which will need to be cut down to size. Use the factory machined line in the

bushing to cut off the small piece shown above.

7. Depending on the baler the bolt may need to be trimmed for proper fit.

8. Tighten all of the hardware to 50 ft/lbs (68 N/m)

9. Make sure that the plastic pad is protecting all metal surfaces of the disc from touching baler.

10. Run the moisture wire harness (006-2470B) from the processor to each disc, securing with cable ties. Be

harness is clear from moving parts, chains and potential pinch points.

11. Apply silicone over nuts and washers to seal moisture way from connections.

Measure 5 1/8”

from this point,

toward top of

the baler

006-4641G

006-4641I

006-2470B

006-4641F

006-4641H

Figure 1

Figure 2

12

End of Bale Sensor Installation

*This sensor is required on Fixed Chamber balers and Optional on all other Models (Kit 200FCA)

The end of bale sensor is used to determine when the baler door is open. With this information the system is

able to show the average moisture of the previous bale.

Locate the sensor (006-7400) and the sensor bracket (001-4648RB). On the right side of the baler find a

location 1”– 6” down from the hinge to mount the bracket. Check for clearance with hydraulic cylinders before

mounting the bracket. The bracket should be mounted to the front side of the hinge point, with the sensor

aligned over the back door.

Mark and drill two 1/4” (7mm) holes and install the bracket using two 5/16” x1/4” self-tapping bolts.

Install the sensor into the bracket and leave 1/4" (7mm) of clearance between the end of sensor and the door.

The harness will need to be routed toward the harness at the tongue of the baler. Secure with cable ties and

take care to avoid pinch points. The harness extension (006-7400EXT) may need to be used.

Control Box Installation

Locate a safe location in the cab of the tractor to place the

control box (006-2471RB). Recommended location is as

close to the tablet or phone being used to control the

system.

Connect the Tractor Power Harness (006-2470T) and the

Baler Power Communication Harness (006-2470B).

The control box (006-2471RB) is equipped with lights to

indicated both power and iPad connection.

Red Light – The control box has power

Green Light – When the active Bluetooth connection is

made with the H2O system, the green light will indicate

connection with the control device.

Hinge Point

001-4648RB

006-7400

View of the right side of baler

Back Door

Front of baler

Baler Power / Communication

Tractor Power

13

200DM Dye Marker Installation (Optional)

Locate the dye marking kit tank and pump assembly (005-9015). Identify a suitable mounting location for the

tank away from moving parts and hydraulic lines on the baler. Be sure to mount the tank within 10’ of the

connection on the Baler Pwr/Comm Harness (006-2470B), wiring details in the wiring diagram.

Note: The mounting location will potentially be different for the tank on each baler model. Due to various baler

designs and modifications, Harvest Tec does not offer a specific mounting location for each baler model.

Once a mounting location has been identified, mount the tank vertically as

shown (right) with the tank lid on the top using the included hardware.

Next locate the dye marking spray assemblies shown (below).

Mount one tip assembly on the right side of the baler positioning the tip to allow

the tip to begin spraying the bale when the door opens. Below (left) is an

example of the tip assembly mounted next to the End of Bale sensor. The nozzle

holder bracket can be bent or adjusted as needed to position properly.

Mount the second tip assembly on the left side of the baler in a

similar position to allow the tip to begin spraying the bale as the door

opens (right).

Routing the Hose

Using the supplied 1/4” hose (002-9006) connect to the pump and secure with the hose clamps (003-9002).

Route the hose to each tip assembly by using the 1/4" Barbed Tee (003-T1414) to go to each side of the baler.

Be sure to avoid moving parts.

14

Wiring Diagram

1. Connect the power harness (006-2470T) to the tractor battery or a convenience outlet using the red wire

with fuse to the positive side and the black wire to the negative.

a. Any modifications of the power harness will void the warranty. Contact Harvest Tec before

modifications are made.

b. This unit will not function on positive ground tractors.

2. The power harness on the tractor (006-2470T) will run from the tractor battery to the control box in the cab

of the tractor (006-2471RB).

3. Connect the keyed power wire (006-5650K) to a keyed power source on the tractor. The keyed power wire

must connect to a keyed source or the unit will not power up correctly.

4. Connect the Baler Pwr/Comm Harness (006-2470B) to the control box in the cab of the tractor.

5. Route the harness to the baler and to each moisture sensor on both sides of bale chamber (006-4641H). If

the baler is a CNH Rollbelt or Kubota round baler the sensors are pn 006-4641HX.

6. When using a Fixed Chamber baler or Dye Marker the End of Bale Sensor kit will need to be added to the

system in order to see when the baler door opens to eject a bale. Part number (200FCA). Connect the

sensor to the End of Bale (EOB) connection on the Baler Pwr/Comm Harness (006-247B).

7. When using the optional Dye Marker (200DM) connect 4 pin round end of the H2O harness (006-2470C) to

the Dye Marker (DM) connection on the (006-2470B) harness. Then connect the two straight spade

connections with only the white wire to the push switch (006-2850). The remaining two connections with 90

degree female spades will connect to the pump.

System wiring diagram

Power Harness on Tractor

006-2470T (15’)

200 Control Box

006-2471RB

Baler Pwr/Comm Harness

006-2470B (18’)

End of Bale Sensor

006-7400

(Complete Kit 200FCA)

Orange Wires to

Keyed Power

006-5650K

Moisture Disc

006-4641H

or

006-4641HX

(CNH Rollbelt &

Kubota Round Baler)

*If needed an optional 8’ Pwr/Comm harness available (not included), part number 006-2470BL. This harness will

mount on the tractor and disconnect from the baler mounted Pwr/Comm harness (006-2470B) at the baler hitch.

*Required on Fixed Chamber Balers

& When Using Dye Marker

Dye Marker

(200DM)

H2O Harness (10’)

006-2470C

15

Downloading H2O App

The H2O App is available on any Apple or Android device running with the current

operating system software and one previous version. Download the app by

searching for H2O Sensor. App icon shown right.

Screen Definitions

Main Screen

Settings Screen

Brightness Adjustment –

Tap to switch between day and

night time brightness

Current App Version

(example)

Current Moisture Reading –

Information will display once hay

enters the bale chamber

Settings Tab – Select to

switch to Settings Screen

Connection Signal - When

wireless connection is made with

the control box light will turn Green

Red – Not Connected

Green - Connected

Home Tab – Select to

change to Home Screen

Dye Sprayer System

*Available 2019*

Serial number of system

Fixed Chamber Baler -

Activate when operating a

fixed chamber baler

On / Off Slide – Slide to the right to turn

On Setting. The bar will turn red or

green (dependent on device)

16

Operation

After installation of the H2O app, turn the system on by turning the key in the tractor on. Ensure the Bluetooth

connection is turned on within your device. When the connection is made the green light on the control box will

illuminate.

Reading Moisture

When hay begins to enter the bale chamber,

current moisture will be displayed

Moisture Range 5-60%

If the moisture being read is Less Than 5% the

reading will appear as shown above

If the moisture being read is Greater Than 60%

the reading will appear as shown above

17

Operation (continued)

Fixed Chamber Balers Only

*200FCA End of Bale Sensor Kit Required

When using a fixed chamber baler, turn on the setting as

shown, and enter the time to make a bale (seconds). This time

is used only until a 3 bale rolling average time is calculated.

Previous bale moisture will now display.

*Current moisture will update when 1/2 of the next bale is

made and / or if using dye sprayer.

The first half of the first bale "--" will be displayed. As the system operates, the system will use the time between End

of Bale signals to calculate an actual time per bale and then use a 3 bale rolling average for the time the current

moisture reading is displayed.

*If you would like to see the previous bale moisture when not using a Fixed Chamber baler the optional

End of Bale Sensor kit will need to be installed (200FCA) and dye sprayer setting turned ‘On’.

18

Operation (continued)

Dye Marker System

When using the dye sprayer turn on the setting as

shown, and select the desired moisture to mark a bale.

*Bales at or above this moisture level will be marked.

Dye Sprayer icon will now appear on the home screen.

The last bale moisture will be highlighted in red and

the bale will be marked at or above the set moisture.

Dye Sprayer Override

If you would like to mark a bale for any reason, press the bale icon which will cause it to turn green.

*At the next End of Bale signal the dye sprayer will mark the bale and the manual override will no longer be

green. When the manual override is used the last bale moisture will not highlight in red.

19

H2O Firmware Update through App

When there is an update available for the H2O system the following information will appear and the steps listed

will need to be followed.

Once an operator downloads the app update (internet connection

required) the “update available” symbol will appear along with the

version number of the available update once connected to the system.

At this point the system can run without updating if the operator

chooses. The icon will simply remain on the screen.

Once the operator decides to perform the software update, they will

press the version number or upload arrow to begin.

Internet connection is not required to perform the update to the module

once the app is downloaded

Once the update is initiated, the system

will enter update mode

The status light will turn red

A green loading symbol will begin to

circulate on the screen

A status bar with then appear to

show the update progress

This can take 3-5 minutes to load software

Once the status bar load completely, the

system will boot back up

The status light will again turn green

The updated version number will be

shown at the bottom of the screen

20

Troubleshooting

Problem

Possible cause(s)

Solution(s)

Moisture reading errors

(reading high or low)

1. Wire disconnected or bad connection

between moisture disc and control box

1. Reconnect wire.

2. Low power supply to control

2. Check voltage at box. Min of 12.5V

3. Hay over 60% moisture

4. Ground contact with one or both

moisture disc and control

4. Reconnect.

5. Short in wire between moisture disc and

control

5. Replace wire.

6. Elevated moisture readings

6. Extreme baler load/density settings.

Adjust baler settings.

Moisture Reading Erratic

1. Check all wiring connections for

corrosion or poor contact.

1. Apply dielectric grease to all

connections.

2. Check power supply at tractor. Voltage

should be constant between 12V-14V

2. Install voltage surge protection on

tractors alternator.

3.Buildup of material around moisture

discs and pads.

3. Remove debris and eliminate any

potential spots on discs that could allow

the material to buildup

Bluetooth Receiver lights

will not illuminate

1. Bluetooth receiver not connected

2. Harness disconnected

3. Low power

1. Check connections and voltage.

Minimum 12.5V needed.

Red Light – The Bluetooth receiver has power

Green Light – When the proper active connection is selected in the Hay App menu, the

green light will indicate connection with the iPad.

Page is loading ...

Harvest TEC 200RBC User manual

This manual is also suitable for

Harvest TEC 200RBC User manual

Related papers

Other documents