Quest Usa WIASUP10031400 LED Wireless Charger User manual
- Type
- User manual
Product Description
LED Wireless Charger
1. Product introduction
Wireless charger with the best quality raw materials and exquisite
design and manufacturing process. Perfect combination of
technology and art, classic elements, fashion and exquisite.
Special SOC intelligent design, accurate calculation, careful control
of the charging and discharging process. Automatic identification
equipment, multi-layer protection, exquisite products, leading
technology, for the majority of users to bring more convenient
charging way!
2. Technical Specifications
Input：5V-2A；9V-1.67A
Output：10W（max）
Specifications：110*26mm
Net weight：72g
3. Product use and function introduction
Ke
y
Wirelesschar
g
esensor
Input port
The figure below shows a simple charging diagram, taking a mobile
phone that meets Qi equipment as an example:
a.Please use the usb-type-c data cable to connect the wireless
charger according to the instruction manual. It is recommended to
use a regular brand power QC adapter to supply power for it.
b. After connecting, the wireless charger will automatically start the
load output and start the charging program. At this time, the
wireless charger will automatically identify and charge the device
with wireless charging function.
c. Put the device supporting wireless charging on the wireless
charger, the device will press the soft shell of the wireless charger
to the wireless charging induction area, and then charge the device
normally.
d. When the receiving device is placed, the charging efficiency is
the highest when the receiving device is aligned with the center of
the wireless charger.
e.When charging the receiving device, the state of the wireless
night light does not change
4. Light control of wireless charger
a. When the wireless charger is connected to the power supply, the
LED light is always on, and the color is the last selected memory
color.
b. The key is used to select the color. Gently press your finger in
the middle of the soft shell to the key in the center of the transmitter.
Short press or double-click the key to select the color.
c. Short press: press the key once each time, the LED light will
change a color
d. Double click: each time you double-click the LED light, there will
be a variety of color lights automatically converted
5. Product precautions
a.This product is only suitable for charging mobile phones and
electronic devices that meet Qi standard. Do not use it for other
purposes;
b.It is forbidden to disassemble the product without permission
c.Please keep the equipment in a well ventilated place away from
high temperature or direct sunlight
d.It is forbidden for children to use this product alone. It should be
used under the supervision of the guardian
e.Handle with care, do not use hard objects to collide with the
beauty mirror
f.During maintenance, it needs to be waterproof to keep the
equipment in power off state
6. FCC Caution
This device complies with Part 15 of the FCC rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
Any changed or modification not expressly approved by the part
responsible for compliance could void the user’s authority to
operate the equipment
Note : This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure
requirement.
To maintain compliance with FCC’s RF exposure guidelines,
this equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body
-
1
-
2
-
3
-
4
-
5
-
6
