Sentera Controls DRM-M-02 Mounting Instruction

Brand: Sentera Controls

Model: DRM-M-02

Category: Electrical relays

Type: Mounting Instruction

DRM-M-02 MODBUS I/O MODULE WITH

2 RELAY OUTPUTS

Mounting and operating instructions

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 2 - 8

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

Table of contents

SAFETY AND PRECAUTIONS 3

PRODUCT DESCRIPTION 4

ARTICLE CODES 4

INTENDED AREA OF USE 4

TECHNICAL DATA 4

STANDARDS 4

WIRING AND CONNECTIONS 5

MOUNTING INSTRUCTIONS IN STEPS 5

VERIFICATION OF INSTALLATION 7

OPERATING INSTRUCTIONS 7

TRANSPORT AND STORAGE 8

WARRANTY AND RESTRICTIONS 8

MAINTENANCE 8

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 3 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

SAFETY AND PRECAUTIONS

Read all the information, the datasheet, Modbus map, mounting and operating

instructions and study the wiring and connection diagram before working with the

product. For personal and equipment safety, and for optimum product performance,

make sure you entirely understand the content before installing, using or servicing

this product.

For safety and licensing (CE) reasons, unauthorised conversion and/ or modiﬁcations

of the product are inadmissible.

e product should not be exposed to abnormal conditions, such as extreme

temperatures, direct sunlight or vibrations. Long-term exposure to chemical

vapours in high concentration can aﬀect the product performance. Make sure the

work environment is as dry as possible; avoid condensation.

All installations shall comply with local health and safety regulations and local

electrical standards and approved codes. is product can only be installed by

an engineer or a technician who has expert knowledge of the product and safety

precautions.

Avoid contact with energised electrical parts. Always disconnect the power supply

before connecting, servicing or repairing the product.

Always verify that you apply appropriate power supply to the product and use

appropriate wire size and characteristics. Make sure that all the screws and nuts

are well tightened and fuses (if any) are ﬁtted well.

Recycling of equipment and packaging should be taken into consideration and these

should be disposed of in accordance with local and national legislation/regulations.

In case there are any questions that are not answered, please contact your

technical support or consult a professional.

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 4 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

PRODUCT DESCRIPTION

DRM-M-02 are relay output modules for Modbus networks. ey feature 2 C/O

relays with a normally open and normally closed contact. e status of the relays

can be controlled by Modbus RTU communication.

ARTICLE CODES

Code Number of relay outputs

DIO-M-02 2

INTENDED AREA OF USE

■ Change relay status via a Modbus RTU master device or BMS

■Control external devices via the relay outputs

TECHNICAL DATA

■2 C/O relays with a normally open and normally closed contact

■Modbus RTU communication

■DIN rail mountable

■ Firmware updates can be pushed via Modbus RTU communication (integrated

bootloader)

■Supply voltage: 24 VDC PoM

■Maximum current consumption: 60 mA

■Maximum switching voltage: 220 VDC / 250 VAC

■Maximum switching current: 5 A (resistive load)

■Protection class: IP30 (EN 60529)

■Enclosure: plastic ABS, UL94-V0, grey RAL 7035

■Operating ambient conditions:

►Temperature: -20—60 °C

►Rel. humidity: 5—90 % rH (non-condensing)

■Storage temperature: -40—85°C

STANDARDS

■Low Voltage Directive 2014/35/EU

► EN 50178:1997 Electronic equipment for use in power installations

► EN 60529:1991 Degrees of protection provided by enclosures (IP Code).

Amendment AC:1993 to EN 60529

■ EMC directive 2014/30/EU:

► EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2: Generic

standards - Immunity for industrial environments. Amendment AC:2005 to

EN 61000-6-2

► EN 61000-6-4:2007 Electromagnetic compatibility (EMC) - Part 6-4: Generic

standards - Emission standard for industrial environments Amendment A1:2011

to EN61000-6-4

■RoHs Directive 2011/65/EU

► EN IEC 63000:2018 Technical documentation for the assessment of electrical

and electronic products with respect to the restriction of hazardous substances

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 5 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

WIRING AND CONNECTIONS

24 VDC PoM – 60 mA max.

Pin 1 Supply voltage, 24 VDC

Pin 2 Supply voltage, 24 VDC

Pin 3 Modbus RTU communication, signal A

Pin 4 Modbus RTU communication, signal A

Pin 5 Modbus RTU communication, signal /B

Pin 6 Modbus RTU communication, signal /B

Pin 7 Ground, supply voltage

Pin 8 Ground, supply voltage

RJ45 socket

GND

8 7 6 5 4 3 2 1

+24 VDC

GND

24 VDC

8 mm

RJ45

Relay outputs

NO1 Normally open contact 1

COM1 Common contact 1

NC1 Normally closed contact 1

NO2 Normally open contact 2

COM2 Common contact 2

NC2 Normally closed contact 2

MOUNTING INSTRUCTIONS IN STEPS

Before you start mounting the unit, read carefully “Safety and Precautions” and

follow these steps:

1. Switch oﬀ the power supply.

2. Slide the unit along the guides of a standard 35 mm DIN rail and ﬁx it to the rail

by means of the black locking clip on the enclosure. Mind the correct position and

mounting dimensions shown in Fig. 1 Mounting dimensions and Fig. 2 Mounting

position.

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 6 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

Fig. 1 Mounting dimensions Fig. 2 Mounting position

94 mm

35 mm

94 mm

66 mm

DIN rail

Locking clip Locked

Unlocked

3. Connect the relay output cables to the terminal block as shown in Fig.3a adhering

to the information in section “Wiring and connections”.

Fig. 3 Wiring diagram

a. Relay outputs

b. RJ45 connector

GND

24 VD

8 mm

RJ45

4. Crimp the RJ45 cable (for 24 VDC power supply and Modbus RTU communication)

and plug it into the socket (see Fig. 3b).

5. Switch on the power supply.

For the complete Modbus register data, refer to the product Modbus Register

Map, which is a separate document attached to the article code on the website

and contains the registers list. Products with earlier ﬁrmware versions may not be

compatible with this list.

NOTE

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 7 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

Optional settings

To assure correct communication, the NBT needs to be activated in only two devices

on the Modbus RTU network. If necessary, enable the NBT resistor via 3SModbus or

Sensistant (Holding register 9).

Example 1 Example 2

ТX

NBT

Slave 2

Master

Slave n

Slave 1

Slave 2

Slave 1

ТX

NBT

Master

Slave n

NOTE On a Modbus RTU network, two bus terminators (NBTs) need to be activated.

VERIFICATION OF INSTALLATION

After powering the unit, the LED on the left of the RJ45 socket (Fig. 4 - 1) should

light up to indicate that the unit is supplied.

e LED on the right of the RJ45 socket (Fig. 4 - 2) indicates that there is active

Modbus communication.

If your unit does not function as expected, please check the connections.

Fig. 4 LED indications

ATTENTION e status of the LEDs can be checked only when the unit is energised. Take the

relevant safety measures!

OPERATING INSTRUCTIONS

e DRM-M-02 are entirely Modbus RTU operated. ey transfer the commands

given via holding registers 11 and 12 to change the C/O contact status.

Bootloader

anks to the bootloader functionality, the unit ﬁrmware can be updated via Modbus

RTU communication. With 3SM boot Application (part of 3SM center software

suite), ‘boot mode’ is automatically activated and the ﬁrmware can be updated.

NOTE Make sure the power supply does not get interrupted during “bootload” procedure,

otherwise you risk losing unsaved data.

www.sentera.eu

MIW-DRM-M-02-EN-000 - 05 / 07 / 2023 8 - 8

back to the table of contents

DRM-M-02 MODBUS I/O MODULE

WITH 2 RELAY OUTPUTS

TRANSPORT AND STORAGE

Avoid shocks and extreme conditions; stock in original packing.

WARRANTY AND RESTRICTIONS

Two years from the delivery date against defects in manufacturing. Any modiﬁcations

or alterations to the product after the date of publication relieve the manufacturer

of any responsibilities. e manufacturer bears no responsibility for any misprints or

mistakes in this data.

MAINTENANCE

In normal conditions this product is maintenance-free. If soiled, clean with a dry or

damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these

circumstances the unit should be disconnected from the supply. Pay attention that

no ﬂuids enter the unit. Only reconnect it to the supply when it is completelydry.

Sentera Controls DRM-M-02 Mounting Instruction

Brand: Sentera Controls

Model: DRM-M-02

Category: Electrical relays

Type: Mounting Instruction

Download PDF

report

Sentera Controls DRM-M-02 Mounting Instruction

Sentera Controls DRM-M-02 Mounting Instruction

Related papers